Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

After a set of SOF-specific changes, this patchset correct problematic
uses of pm_runtime_get_sync() in ASoC, or simplifies the flow with no
functional changes. Two patches for Intel platforms also add a test on
resume success.

Additional changes were initially suggested to completely remove the
use of pm_runtime_get_sync(). These changes were dropped since they
are way too invasive, specifically in cases where the return values
were not tested, which would lead to duplicate pm_runtime_put(). The
remaining uses of pm_runtime_get_sync() cannot really be blindly
modified without context and knowledge of each driver.

h1940_uda1380 uses gpiod*/GPIOD* so it should include GPIO consumer
header.

Fixes: 9666e27f ("ASoC: samsung: h1940: turn into platform driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627141900.470469-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Allow compile testing of Samsung SoC Sound drivers.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627143412.477226-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The module does not use anything from gpio.h header.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627143412.477226-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

There is no particular need to restrict building of S3C I2S driver to
supported platforms within the C unit, because Kconfig does it.
Removing such restricting #ifdef from s3c-i2s-v2 allows compile testing
it on other platforms.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627143412.477226-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Daniel Mack <daniel@zonque.org>:

This is a series of some patches that I collected while using the
max98396 driver is a TDM mode setup.

They correct BSEL and PCM mode configs, add support for power supplies
and add some bits to the documentation.

The code is tested in TDM-16 and TDM-8 mode with 32 channel width.

Merge series from Samuel Holland <samuel@sholland.org>:

This series adds support for enabling the codec's internal microphone
bias, which is needed on at least some versions of the PinePhone.

Changes in v2:
 - Move register update from component probe to device probe

Arnaud Ferraris (2):
  ASoC: dt-bindings: sun50i-codec: Add binding for internal bias
  ASoC: sun50i-codec-analog: Add support for internal bias

Samuel Holland (1):
  arm64: dts: allwinner: pinephone: Enable internal HMIC bias

 .../bindings/sound/allwinner,sun50i-a64-codec-analog.yaml | 5 +++++
 .../arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts | 4 ++++
 .../arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts | 4 ++++
 sound/soc/sunxi/sun50i-codec-analog.c                     | 8 ++++++++
 4 files changed, 21 insertions(+)

--
2.35.1

The conversion of the set_fmt callback to direct clock specification
included a small typo, correct the affected code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627094335.3051210-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Further development will need some of the fixes.

In order to properly bias headset microphones, there should be a pull-up
resistor between pins HBIAS and MIC2P. This can be an external resistor,
but the codec also provides an internal 2.2K resistor which is enabled
by a register.

This patch enables or disables the internal bias resistor based on a
device tree property.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
[Samuel: split binding and implementation; move to device probe]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220621035452.60272-3-samuel@sholland.orgSigned-off-by: Mark Brown <broonie@kernel.org>

In order to properly bias headset microphones, there should be a pull-up
resistor between pins HBIAS and MIC2P. This can be an external resistor,
but the codec also provides an internal 2.2K resistor which is enabled
by a register.

This patch adds a device-tree property to the sun50i-codec-analog driver
to take advantage of this feature.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
[Samuel: split binding and implementation patches]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220621035452.60272-2-samuel@sholland.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The use of pm_runtime_get_sync() is buggy with no use of put_noidle on
error.

Use pm_runtime_resume_and_get() instead.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-12-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The use of pm_runtime_get_sync() is buggy with no use of put_noidle() on
error.

Use pm_runtime_resume_and_get() instead.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-11-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simplify the flow.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-10-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simplify the flow.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-9-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simplify the flow.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-8-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

simplify the flow. No functionality change, except that on -EACCESS
the reference count will be decreased.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

simplify the flow. No functionality change, except that on -EACCESS
the reference count will be decreased.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

simplify the flow. No functionality change, except that on -EACCESS
the reference count will be decreased.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The current code does not check for errors and does not release the
reference on errors.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The current code does not check for errors and does not release the
reference on errors.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Allow the selection of the TDM slot that is used to send back speaker
monitor data. The DT property adi,spkfb-slot-no can be used to configure
this setting which defaults to 2.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-8-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

max98396_dai_set_fmt() modifes register 2041 and touches bits in the mask
0x3a. Make sure to use the right mask for that operation.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-7-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Let's log what actually failed and log at some more places.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-6-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The device has up to 5 potentially independent power supplies:
AVDD, DVDD, DVVDIO, VBAT and PVDD. The former 3 are mandatory for the
device to function. One of VBAT and PVDD should also be made available.

Regulators are enabled during probe time and will stay active except when in
suspend mode.

Futher, the chip needs to be informed about the presence of VBAT through a
bit in register 0x20a0.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-5-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This property allows to select the PCM data input channel that is
routed to the speaker audio processing bypass path.

The driver already implements this property.

While at it, fix the default value for adi,imon-slot-no.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-4-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The device is supplied with 3 core voltages (DVVDIO, DVDD, AVDD), and
PVDD and/or VBAT.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-2-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The example in audio-graph-card2.c has multiple nodes with the same name
in it. Change the port numbers to get different names.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220624092601.2445224-1-s.hauer@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

Put the SGTL5000 in a silent/safe state on shutdown/remove, this is
required since the SGTL5000 produces a constant noise on its output
after it is configured and its clock is removed. Without this change
this is happening every time the module is unbound/removed or from
reboot till the clock is enabled again.

The issue was experienced on both a Toradex Colibri/Apalis iMX6, but can
be easily reproduced everywhere just playing something on the codec and
after that removing/unbinding the driver.

Fixes: 9b34e6cc ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220624101301.441314-1-francesco.dolcini@toradex.comSigned-off-by: Mark Brown <broonie@kernel.org>

There are some functions that were missed by commit d77e7456 ("regmap:
Add bulk read/write callbacks into regmap_config") when support to define
bulk read/write callbacks in regmap_config was introduced.

The regmap_bulk_write() and regmap_noinc_write() functions weren't changed
to use the added map->write instead of the map->bus->write handler.

Also, the regmap_can_raw_write() was not modified to take map->write into
account. So will only return true if a bus with a .write callback is set.

Fixes: d77e7456 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20220616073435.1988219-4-javierm@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Before adding support to define bulk read/write callbacks in regmap_config
by the commit d77e7456 ("regmap: Add bulk read/write callbacks into
regmap_config"), the regmap_noinc_read() function returned an errno early
a map->bus->read callback wasn't set.

But that commit dropped the check and now a call to _regmap_raw_read() is
attempted even when bulk read operations are not supported. That function
checks for map->read anyways but there's no point to continue if the read
can't succeed.

Also is a fragile assumption to make so is better to make it fail earlier.

Fixes: d77e7456 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20220616073435.1988219-3-javierm@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Support for drivers to define bulk read/write callbacks in regmap_config
was introduced by the commit d77e7456 ("regmap: Add bulk read/write
callbacks into regmap_config"), but this commit wrongly dropped a check
in regmap_bulk_read() to determine whether bulk reads can be done or not.

Before that commit, it was checked if map->bus was set. Now has to check
if a map->read callback has been set.

Fixes: d77e7456 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20220616073435.1988219-2-javierm@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

madera_adsp_rate_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the
value is changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-5-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

madera_out1_demux_put returns the value of
snd_soc_dapm_mux_update_power, which returns a 1 if a path was found for
the kcontrol. This is obviously different to the expected return a 1 if
the control was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-4-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

cs47l15_in1_adc_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-3-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The mixer controls for ASP TX3/4 are set to values that are not included
in their enumeration control. This will cause spurious event
notifications when the controls are first changed, as the register value
changes whilst the actual visible enumeration value does not. Use the
register patch to set them to a known value, zero, which equates to zero
fill, thereby avoiding the spurious notifications.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-2-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

DAPM keeps a copy of the current value of mux/demux controls,
however this value is only initialised in the case of autodisable
controls. This leads to false notification events when first
modifying a DAPM kcontrol that has a non-zero default.

Autodisable controls are left as they are, since they already
initialise the value, and there would be more work required to
support autodisable muxes where the first option isn't disabled
and/or that isn't the default.

Technically this issue could affect mixer/switch elements as well,
although not on any of the devices I am currently running. There
is also a little more work to do to address the issue there due to
that side supporting stereo controls, so that has not been tackled
in this patch.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The initial settings will be written before the codec probe function.
But, the rt711->component doesn't be assigned yet.
If IO error happened during initial settings operations, it will cause the kernel panic.
This patch changed component->dev to slave->dev to fix this issue.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220621090719.30558-1-shumingf@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Various boolean controls on cs35l41 are missing the required "Switch" in
the name, add these.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220621102041.1713504-3-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The DRE controls on wm5110 should return a value of 1 if the DRE state
is actually changed, update to fix this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220621102041.1713504-2-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>