The datasheet doesn't say anything about writing twice, so this was
probably overlooked.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Don't open code the AC_READ and AC_WRITE macros.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

stmpe touchscreen supports BTN_TOUCH event but doesn't report it. Add
BTN_TOUCH reporting capability to the stmpe touchscreen driver.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver's timer must be set up before enabling IRQ handler, otherwise
bad things may happen.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Popovec <popovec@fei.tuke.sk>
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This saves us a few lines of code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This saves us a few lines of code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch to using devm_*() interfaces to manage our resources,
thus will simplify error unwinding a bit.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Failures to build a keymap, request an IRQ, or register input device are
fatal for the driver, therefore the messages should have "error" severity
instead of "debug".
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This matches structure of most other input drivers.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We need to use proper accessor functions instead of directly poking into
various structures.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use a temporary variable for our parent device (coming from I2C client
structure); we'll be also using it during conversion to managed resources.
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The kernel does not contain the symbol SA1100_BITSY so the driver
is never compiled and can be removed safely.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Now we can register the BU21013_ts touch screen when booting with Device
Tree enabled. Here we parse all the necessary components previously
expected to be passed from platform data.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

These GPIO init and exit functions have no place in platform data, they
should be part of the driver instead,
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Currently the BU21013 Touch Screen driver requests a regulator by the
name of 'V-TOUCH', which doesn't exist anywhere in the kernel. The
correct name, as referenced in platform regulator code is 'avdd'. Here,
when we request a regulator, we use the correct name instead.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We're currently carrying two 'struct bu21013_platform_device's which
are identical for no apparent reason. Here we remove the extra burden
and apply the same information to the two different instances of the
bu21012_tp driver registration.

[Dmitry Torokhov: picked it up to (hopefully) reduce merge conflict with
 bu21013_ts update that follows.]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Disable hardware if active when suspending if the hw can not
wake the system from suspend.

[Dmitry Torokhov: use input_dev->users instead of a separate flag]
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Reviewed-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of reporting the initial stage when the device is registered we
should do it when the device is opened (so there are users).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

devm_* functions are device managed and make error handling and code
simpler. While at it also fix error exit paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

clk_{un}prepare is mandatory for platforms using common clock framework.
Because for SPEAr we don't do anything in clk_{un}prepare() calls, just
call them once in probe/remove.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In imx_keypad_inhibit(), all 8 columns were set to open-drain, in
contrast to the rest of the driver, where only the enabled columns
are modified/used.

Contrary to the normal expectation, this also affects column I/Os not
even mapped via IOMUX to the KPP hardware module but used as a GPIO.
Therefore only init enabled columns to open-drain and leave all others
with their default reset value of 0, i.e. totem-pole.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We do not need to call tasklet_disable() before calling tasklet_kill() if
taskelt does not reschedult itself.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

To facilitate upcoming cleanup in twl stack switch from using
TWL4030_MODULE_PM_MASTER define to usingTWL_MODULE_PM_MASTER.
There are no functional changes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch allows the STMPE driver to be successfully probed and
initialised when Device Tree support is enabled. Besides the usual
platform data changes, we also separate the process of filling in
the 'in use' pin bitmap, as we have to extract the information from
Device Tree in the DT boot case.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Remove conditional code based on CONFIG_HOTPLUG being false.  It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Bring in changes to ads7846 to avoid mereg conflicts.

This patch allows the STMPE Touchscreen driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It supports 10 fingers.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The updated type enum enables this implementation.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 97ee9f01 (ARM: OMAP: fix the ads7846 init code) have enabled the
pendown GPIO debounce time setting by the below sequence:

  gpio_request_one()
  gpio_set_debounce()
  gpio_free()

It also revealed a bug in the OMAP GPIO handling code which prevented
the GPIO debounce clock to be disabled and CORE transition to low power
states.

Commit c9c55d92 (gpio/omap: fix off-mode bug: clear debounce settings on
free/reset) fixes the OMAP GPIO handling code by making sure that the
GPIO debounce clock gets disabled if no GPIO is requested from current
bank.

While fixing the OMAP GPIO handling code (in the right way), the above
commit makes the gpio_request->set_debounce->free sequence invalid as
after freeing the GPIO, the debounce settings are lost.

Fix the debounce settings by moving the debounce initialization to the
actual GPIO requesting code - the ads7846 driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>