Pull more libata updates from Damien Le Moal:
 "Second round of updates for libata for 5.16:

   - Fix READ LOG EXT and READ LOG DMA EXT command timeouts during disk
     revalidation after a resume or a modprobe of the LLDD (me)

   - Remove unnecessary error message in sata_highbank driver (Xu)

   - Better handling of accesses to the IDENTIFY DEVICE data log for
     drives that do not support this log page (me)

   - Fix ahci_shost_attr_group declaration in ahci driver (me)"

* tag 'libata-5.16-rc1-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  libata: libahci: declare ahci_shost_attr_group as static
  libata: add horkage for missing Identify Device log
  ata: sata_highbank: Remove unnecessary print function dev_err()
  libata: fix read log timeout value

TL;DR: While a tool like liblockdep is useful, it probably doesn't
belong within the kernel tree.

liblockdep attempts to reuse kernel code both directly (by directly
building the kernel's lockdep code) as well as indirectly (by using
sanitized headers). This makes liblockdep an integral part of the
kernel.

It also makes liblockdep quite unique: while other userspace code might
use sanitized headers, it generally doesn't attempt to use kernel code
directly which means that changes on the kernel side of things don't
affect (and break) it directly.

All our workflows and tooling around liblockdep don't support this
uniqueness. Changes that go into the kernel code aren't validated to not
break in-tree userspace code.

liblockdep ended up being very fragile, breaking over and over, to the
point that living in the same tree as the lockdep code lost most of it's
value.

liblockdep should continue living in an external tree, syncing with
the kernel often, in a controllable way.
Signed-off-by: Sasha Levin <sashal@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit aeb58c86 ("thermal/drivers/int340x: processor_thermal: Suppot
64 bit RFIM responses") started using 'readq()' to read 64-bit status
responses from the int340x hardware.

That's all fine and good, but on 32-bit targets a 64-bit 'readq()' is
ambiguous, since it's no longer an atomic access.  Some hardware might
require 64-bit accesses, and other hardware might want low word first or
high word first.

It's quite likely that the driver isn't relevant in a 32-bit environment
any more, and there's a patch floating around to just make it depend on
X86_64, but let's make it buildable on x86-32 anyway.

The driver previously just read the low 32 bits, so the hardware
certainly is ok with 32-bit reads, and in a little-endian environment
the low word first model is the natural one.

So just add the include for the 'io-64-nonatomic-lo-hi.h' version.

Fixes: aeb58c86 ("thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull PCI fixes from Bjorn Helgaas:
 "Revert conversion to struct device.driver instead of struct
  pci_dev.driver.

  The device.driver is set earlier, and using it caused the PCI core to
  call driver PM entry points before .probe() and after .remove(), when
  the driver isn't prepared.

  This caused NULL pointer dereferences in i2c_designware_pci and
  probably other driver issues"

* tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "PCI: Use to_pci_driver() instead of pci_dev->driver"
  Revert "PCI: Remove struct pci_dev->driver"

ahci_shost_attr_group is referenced only in drivers/ata/libahci.c.
Declare it as static.

Fixes: c3f69c7f ("scsi: ata: Switch to attribute groups")
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>

ACS-3 introduced the ATA Identify Device Data log as mandatory. A
warning message currently signals to the user if a device does not
report supporting this log page in the log directory page, regardless
of the ATA version of the device. Furthermore, this warning will appear
for all attempts at accessing this missing log page during device
revalidation.

Since it is useless to constantly access the log directory and warn
about this lack of support once we have discovered that the device
does not support this log page, introduce the horkage flag
ATA_HORKAGE_NO_ID_DEV_LOG to mark a device as lacking support for
the Identify Device Data log page. Set this flag when
ata_log_supported() returns false in ata_identify_page_supported().
The warning is printed only if the device ATA level is 10 or above
(ACS-3 or above), and only once on device scan. With this flag set, the
log directory page is not accessed again to test for Identify Device
Data log page support.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull KCSAN updates from Paul McKenney:
 "This contains initialization fixups, testing improvements, addition of
  instruction pointer to data-race reports, and scoped data-race checks"

* tag 'kcsan.2021.11.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
  kcsan: selftest: Cleanup and add missing __init
  kcsan: Move ctx to start of argument list
  kcsan: Support reporting scoped read-write access type
  kcsan: Start stack trace with explicit location if provided
  kcsan: Save instruction pointer for scoped accesses
  kcsan: Add ability to pass instruction pointer of access to reporting
  kcsan: test: Fix flaky test case
  kcsan: test: Use kunit_skip() to skip tests
  kcsan: test: Defer kcsan_test_init() after kunit initialization

Merge tag 'apparmor-pr-2021-11-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor

Pull apparmor updates from John Johansen:
 "Features
   - use per file locks for transactional queries
   - update policy management capability checks to work with LSM stacking

  Bug Fixes:
   - check/put label on apparmor_sk_clone_security()
   - fix error check on update of label hname
   - fix introspection of of task mode for unconfined tasks

  Cleanups:
   - avoid -Wempty-body warning
   - remove duplicated 'Returns:' comments
   - fix doc warning
   - remove unneeded one-line hook wrappers
   - use struct_size() helper in kzalloc()
   - fix zero-length compiler warning in AA_BUG()
   - file.h: delete duplicated word
   - delete repeated words in comments
   - remove repeated declaration"

* tag 'apparmor-pr-2021-11-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
  apparmor: remove duplicated 'Returns:' comments
  apparmor: remove unneeded one-line hook wrappers
  apparmor: Use struct_size() helper in kzalloc()
  apparmor: fix zero-length compiler warning in AA_BUG()
  apparmor: use per file locks for transactional queries
  apparmor: fix doc warning
  apparmor: Remove the repeated declaration
  apparmor: avoid -Wempty-body warning
  apparmor: Fix internal policy capable check for policy management
  apparmor: fix error check
  security: apparmor: delete repeated words in comments
  security: apparmor: file.h: delete duplicated word
  apparmor: switch to apparmor to internal capable check for policy management
  apparmor: update policy capable checks to use a label
  apparmor: fix introspection of of task mode for unconfined tasks
  apparmor: check/put label on apparmor_sk_clone_security()

Merge more updates from Andrew Morton:
 "The post-linux-next material.

  7 patches.

  Subsystems affected by this patch series (all mm): debug,
  slab-generic, migration, memcg, and kasan"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  kasan: add kasan mode messages when kasan init
  mm: unexport {,un}lock_page_memcg
  mm: unexport folio_memcg_{,un}lock
  mm/migrate.c: remove MIGRATE_PFN_LOCKED
  mm: migrate: simplify the file-backed pages validation when migrating its mapping
  mm: allow only SLUB on PREEMPT_RT
  mm/page_owner.c: modify the type of argument "order" in some functions

Pull m68knommu updates from Greg Ungerer:
 "Only two changes.

  One removes the now unused CONFIG_MCPU32 symbol. The other sets a
  default for the CONFIG_MEMORY_RESERVE config symbol (this aids
  scripting and other automation) so you don't interactively get asked
  for a value at configure time.

  Summary:

   - remove unused CONFIG_MCPU32 symbol

   - default CONFIG_MEMORY_RESERVE value (for scripting)"

* tag 'm68knommu-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: Remove MCPU32 config symbol
  m68k: set a default value for MEMORY_RESERVE

This reverts commit 2a4d9408.

Robert reported a NULL pointer dereference caused by the PCI core
(local_pci_probe()) calling the i2c_designware_pci driver's
.runtime_resume() method before the .probe() method.  i2c_dw_pci_resume()
depends on initialization done by i2c_dw_pci_probe().

Prior to 2a4d9408 ("PCI: Use to_pci_driver() instead of
pci_dev->driver"), pci_pm_runtime_resume() avoided calling the
.runtime_resume() method because pci_dev->driver had not been set yet.

2a4d9408 and b5f9c644 ("PCI: Remove struct pci_dev->driver"),
removed pci_dev->driver, replacing it by device->driver, which *has* been
set by this time, so pci_pm_runtime_resume() called the .runtime_resume()
method when it previously had not.

Fixes: 2a4d9408 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

This reverts commit b5f9c644.

Revert b5f9c644 ("PCI: Remove struct pci_dev->driver"), which is needed
to revert 2a4d9408 ("PCI: Use to_pci_driver() instead of
pci_dev->driver").

2a4d9408 caused a NULL pointer dereference reported by Robert Święcki.
Details in the revert of that commit.

Fixes: 2a4d9408 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Pull tracing fixes from Steven Rostedt:
 "Two locking fixes:

   - Add mutex protection to ring_buffer_reset()

   - Fix deadlock in modify_ftrace_direct_multi()"

* tag 'trace-v5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace/direct: Fix lockup in modify_ftrace_direct_multi
  ring-buffer: Protect ring_buffer_reset() from reentrancy

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf, can and netfilter.

  Current release - regressions:

   - bpf: do not reject when the stack read size is different from the
     tracked scalar size

   - net: fix premature exit from NAPI state polling in napi_disable()

   - riscv, bpf: fix RV32 broken build, and silence RV64 warning

  Current release - new code bugs:

   - net: fix possible NULL deref in sock_reserve_memory

   - amt: fix error return code in amt_init(); fix stopping the
     workqueue

   - ax88796c: use the correct ioctl callback

  Previous releases - always broken:

   - bpf: stop caching subprog index in the bpf_pseudo_func insn

   - security: fixups for the security hooks in sctp

   - nfc: add necessary privilege flags in netlink layer, limit
     operations to admin only

   - vsock: prevent unnecessary refcnt inc for non-blocking connect

   - net/smc: fix sk_refcnt underflow on link down and fallback

   - nfnetlink_queue: fix OOB when mac header was cleared

   - can: j1939: ignore invalid messages per standard

   - bpf, sockmap:
      - fix race in ingress receive verdict with redirect to self
      - fix incorrect sk_skb data_end access when src_reg = dst_reg
      - strparser, and tls are reusing qdisc_skb_cb and colliding

   - ethtool: fix ethtool msg len calculation for pause stats

   - vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries to
     access an unregistering real_dev

   - udp6: make encap_rcv() bump the v6 not v4 stats

   - drv: prestera: add explicit padding to fix m68k build

   - drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge

   - drv: mvpp2: fix wrong SerDes reconfiguration order

  Misc & small latecomers:

   - ipvs: auto-load ipvs on genl access

   - mctp: sanity check the struct sockaddr_mctp padding fields

   - libfs: support RENAME_EXCHANGE in simple_rename()

   - avoid double accounting for pure zerocopy skbs"

* tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (123 commits)
  selftests/net: udpgso_bench_rx: fix port argument
  net: wwan: iosm: fix compilation warning
  cxgb4: fix eeprom len when diagnostics not implemented
  net: fix premature exit from NAPI state polling in napi_disable()
  net/smc: fix sk_refcnt underflow on linkdown and fallback
  net/mlx5: Lag, fix a potential Oops with mlx5_lag_create_definer()
  gve: fix unmatched u64_stats_update_end()
  net: ethernet: lantiq_etop: Fix compilation error
  selftests: forwarding: Fix packet matching in mirroring selftests
  vsock: prevent unnecessary refcnt inc for nonblocking connect
  net: marvell: mvpp2: Fix wrong SerDes reconfiguration order
  net: ethernet: ti: cpsw_ale: Fix access to un-initialized memory
  net: stmmac: allow a tc-taprio base-time of zero
  selftests: net: test_vxlan_under_vrf: fix HV connectivity test
  net: hns3: allow configure ETS bandwidth of all TCs
  net: hns3: remove check VF uc mac exist when set by PF
  net: hns3: fix some mac statistics is always 0 in device version V2
  net: hns3: fix kernel crash when unload VF while it is being reset
  net: hns3: sync rx ring head in echo common pull
  net: hns3: fix pfc packet number incorrect after querying pfc parameters
  ...

Pull char/misc fix from Greg KH:
 "Here is a single fix for 5.16-rc1 to resolve a build problem that came
  in through the coresight tree (and as such came in through the
  char/misc tree merge in the 5.16-rc1 merge window).

  It resolves a build problem with 'allmodconfig' on arm64 and is acked
  by the proper subsystem maintainers. It has been in linux-next all
  week with no reported problems"

* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  arm64: cpufeature: Export this_cpu_has_cap helper

Pull USB fixes from Greg KH:
 "Here are some small reverts and fixes for USB drivers for issues that
  came up during the 5.16-rc1 merge window.

  These include:

   - two reverts of xhci and USB core patches that are causing problems
     in many systems.

   - xhci 3.1 enumeration delay fix for systems that were having
     problems.

  All three of these have been in linux-next all week with no reported
  issues"

* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: Fix USB 3.1 enumeration issues by increasing roothub power-on-good delay
  Revert "usb: core: hcd: Add support for deferring roothub registration"
  Revert "xhci: Set HCD flag to defer primary roothub registration"

There are multiple kasan modes.  It makes sense that we add some
messages to know which kasan mode is active when booting up [1].

Link: https://bugzilla.kernel.org/show_bug.cgi?id=212195 [1]
Link: https://lkml.kernel.org/r/20211020094850.4113-1-Kuan-Ying.Lee@mediatek.comSigned-off-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Reviewed-by: Marco Elver <elver@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: Yee Lee <yee.lee@mediatek.com>
Cc: Nicholas Tang <nicholas.tang@mediatek.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

These are only used in built-in core mm code.

Link: https://lkml.kernel.org/r/20210820095815.445392-3-hch@lst.deSigned-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Patch series "unexport memcg locking helpers".

Neither the old page-based nor the new folio-based memcg locking helpers
are used in modular code at all, so drop the exports.

This patch (of 2):

folio_memcg_{,un}lock are only used in built-in core mm code.

Link: https://lkml.kernel.org/r/20210820095815.445392-1-hch@lst.de
Link: https://lkml.kernel.org/r/20210820095815.445392-2-hch@lst.deSigned-off-by: Christoph Hellwig <hch@lst.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MIGRATE_PFN_LOCKED is used to indicate to migrate_vma_prepare() that a
source page was already locked during migrate_vma_collect().  If it
wasn't then the a second attempt is made to lock the page.  However if
the first attempt failed it's unlikely a second attempt will succeed,
and the retry adds complexity.  So clean this up by removing the retry
and MIGRATE_PFN_LOCKED flag.

Destination pages are also meant to have the MIGRATE_PFN_LOCKED flag
set, but nothing actually checks that.

Link: https://lkml.kernel.org/r/20211025041608.289017-1-apopple@nvidia.comSigned-off-by: Alistair Popple <apopple@nvidia.com>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There is no need to validate the file-backed page's refcount before
trying to freeze the page's expected refcount, instead we can rely on
the folio_ref_freeze() to validate if the page has the expected refcount
before migrating its mapping.

Moreover we are always under the page lock when migrating the page
mapping, which means nowhere else can remove it from the page cache, so
we can remove the xas_load() validation under the i_pages lock.

Link: https://lkml.kernel.org/r/cover.1629447552.git.baolin.wang@linux.alibaba.com
Link: https://lkml.kernel.org/r/df4c129fd8e86a95dbc55f4663d77441cc0d3bd1.1629447552.git.baolin.wang@linux.alibaba.comSigned-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Suggested-by: Matthew Wilcox <willy@infradead.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Alistair Popple <apopple@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Memory allocators may disable interrupts or preemption as part of the
allocation and freeing process.  For PREEMPT_RT it is important that
these sections remain deterministic and short and therefore don't depend
on the size of the memory to allocate/ free or the inner state of the
algorithm.

Until v3.12-RT the SLAB allocator was an option but involved several
changes to meet all the requirements.  The SLUB design fits better with
PREEMPT_RT model and so the SLAB patches were dropped in the 3.12-RT
patchset.  Comparing the two allocator, SLUB outperformed SLAB in both
throughput (time needed to allocate and free memory) and the maximal
latency of the system measured with cyclictest during hackbench.

SLOB was never evaluated since it was unlikely that it preforms better
than SLAB.  During a quick test, the kernel crashed with SLOB enabled
during boot.

Disable SLAB and SLOB on PREEMPT_RT.

[bigeasy@linutronix.de: commit description]

Link: https://lkml.kernel.org/r/20211015210336.gen3tib33ig5q2md@linutronix.deSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The type of "order" in struct page_owner is unsigned short.
However, it is unsigned int in the following 3 functions:

  __reset_page_owner
  __set_page_owner_handle
  __set_page_owner_handle

The type of "order" in argument list is unsigned int, which is
inconsistent.

[akpm@linux-foundation.org: update include/linux/page_owner.h]

Link: https://lkml.kernel.org/r/20211020125945.47792-1-caoyixuan2019@email.szu.edu.cnSigned-off-by: Yixuan Cao <caoyixuan2019@email.szu.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The below commit added optional support for passing a bind address.
It configures the sockaddr bind arguments before parsing options and
reconfigures on options -b and -4.

This broke support for passing port (-p) on its own.

Configure sockaddr after parsing all arguments.

Fixes: 3327a9c4 ("selftests: add functionals test for UDP GRO")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

curr_phase is unused. Removed the dead code.

Fixes: 8d9be063 ("net: wwan: iosm: transport layer support for fw flashing/cd")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensure diagnostics monitoring support is implemented for the SFF 8472
compliant port module and set the correct length for ethtool port
module eeprom read.

Fixes: f56ec676 ("cxgb4: Add support for ethtool i2c dump")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The print function dev_err() is redundant because
platform_get_irq() already prints an error.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>

Some ATA drives are very slow to respond to READ_LOG_EXT and
READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the
device is revalidated right after resuming a system or inserting the
ATA adapter driver (e.g. ahci). The default 5s timeout
(ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing
errors during the device configuration. Ex:

...
ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: ATA-9: XXX  XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133
ata9.00: qc timeout (cmd 0x2f)
ata9.00: Read log page 0x00 failed, Emask 0x4
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: NCQ Send/Recv Log not supported
ata9.00: Read log page 0x08 failed, Emask 0x40
ata9.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: ATA Identify Device Log not supported
ata9.00: failed to set xfermode (err_mask=0x40)
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: configured for UDMA/133
...

The timeout error causes a soft reset of the drive link, followed in
most cases by a successful revalidation as that give enough time to the
drive to become fully ready to quickly process the read log commands.
However, in some cases, this also fails resulting in the device being
dropped.

Fix this by using adding the ata_eh_revalidate_timeouts entries for the
READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout
increased to 15s, retriable one time.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>

Commit 719c5719 ("net: make napi_disable() symmetric with
enable") accidentally introduced a bug sometimes leading to a kernel
BUG when bringing an iface up/down under heavy traffic load.

Prior to this commit, napi_disable() was polling n->state until
none of (NAPIF_STATE_SCHED | NAPIF_STATE_NPSVC) is set and then
always flip them. Now there's a possibility to get away with the
NAPIF_STATE_SCHE unset as 'continue' drops us to the cmpxchg()
call with an uninitialized variable, rather than straight to
another round of the state check.

Error path looks like:

napi_disable():
unsigned long val, new; /* new is uninitialized */

do {
	val = READ_ONCE(n->state); /* NAPIF_STATE_NPSVC and/or
				      NAPIF_STATE_SCHED is set */
	if (val & (NAPIF_STATE_SCHED | NAPIF_STATE_NPSVC)) { /* true */
		usleep_range(20, 200);
		continue; /* go straight to the condition check */
	}
	new = val | <...>
} while (cmpxchg(&n->state, val, new) != val); /* state == val, cmpxchg()
						  writes garbage */

napi_enable():
do {
	val = READ_ONCE(n->state);
	BUG_ON(!test_bit(NAPI_STATE_SCHED, &val)); /* 50/50 boom */
<...>

while the typical BUG splat is like:

[  172.652461] ------------[ cut here ]------------
[  172.652462] kernel BUG at net/core/dev.c:6937!
[  172.656914] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[  172.661966] CPU: 36 PID: 2829 Comm: xdp_redirect_cp Tainted: G          I       5.15.0 #42
[  172.670222] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0014.082620210524 08/26/2021
[  172.680646] RIP: 0010:napi_enable+0x5a/0xd0
[  172.684832] Code: 07 49 81 cc 00 01 00 00 4c 89 e2 48 89 d8 80 e6 fb f0 48 0f b1 55 10 48 39 c3 74 10 48 8b 5d 10 f6 c7 04 75 3d f6 c3 01 75 b4 <0f> 0b 5b 5d 41 5c c3 65 ff 05 b8 e5 61 53 48 c7 c6 c0 f3 34 ad 48
[  172.703578] RSP: 0018:ffffa3c9497477a8 EFLAGS: 00010246
[  172.708803] RAX: ffffa3c96615a014 RBX: 0000000000000000 RCX: ffff8a4b575301a0
< snip >
[  172.782403] Call Trace:
[  172.784857]  <TASK>
[  172.786963]  ice_up_complete+0x6f/0x210 [ice]
[  172.791349]  ice_xdp+0x136/0x320 [ice]
[  172.795108]  ? ice_change_mtu+0x180/0x180 [ice]
[  172.799648]  dev_xdp_install+0x61/0xe0
[  172.803401]  dev_xdp_attach+0x1e0/0x550
[  172.807240]  dev_change_xdp_fd+0x1e6/0x220
[  172.811338]  do_setlink+0xee8/0x1010
[  172.814917]  rtnl_setlink+0xe5/0x170
[  172.818499]  ? bpf_lsm_binder_set_context_mgr+0x10/0x10
[  172.823732]  ? security_capable+0x36/0x50
< snip >

Fix this by replacing 'do { } while (cmpxchg())' with an "infinite"
for-loop with an explicit break.

From v1 [0]:
 - just use a for-loop to simplify both the fix and the existing
   code (Eric).

[0] https://lore.kernel.org/netdev/20211110191126.1214-1-alexandr.lobakin@intel.com

Fixes: 719c5719 ("net: make napi_disable() symmetric with enable")
Suggested-by: Eric Dumazet <edumazet@google.com> # for-loop
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211110195605.1304-1-alexandr.lobakin@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull ext4 updates from Ted Ts'o:
 "Only bug fixes and cleanups for ext4 this merge window.

  Of note are fixes for the combination of the inline_data and
  fast_commit fixes, and more accurately calculating when to schedule
  additional lazy inode table init, especially when CONFIG_HZ is 100HZ"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix error code saved on super block during file system abort
  ext4: inline data inode fast commit replay fixes
  ext4: commit inline data during fast commit
  ext4: scope ret locally in ext4_try_to_trim_range()
  ext4: remove an unused variable warning with CONFIG_QUOTA=n
  ext4: fix boolreturn.cocci warnings in fs/ext4/name.c
  ext4: prevent getting empty inode buffer
  ext4: move ext4_fill_raw_inode() related functions
  ext4: factor out ext4_fill_raw_inode()
  ext4: prevent partial update of the extent blocks
  ext4: check for inconsistent extents between index and leaf block
  ext4: check for out-of-order index extents in ext4_valid_extent_entries()
  ext4: convert from atomic_t to refcount_t on ext4_io_end->count
  ext4: refresh the ext4_ext_path struct after dropping i_data_sem.
  ext4: ensure enough credits in ext4_ext_shift_path_extents
  ext4: correct the left/middle/right debug message for binsearch
  ext4: fix lazy initialization next schedule time computation in more granular unit
  Revert "ext4: enforce buffer head state assertion in ext4_da_map_blocks"

Pull btrfs fix from David Sterba:
 "Fix for a deadlock when direct/buffered IO is done on a mmaped file
  and a fault happens (details in the patch). There's a fstest
  generic/647 that triggers the problem and makes testing hard"

* tag 'for-5.16-deadlock-fix-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix deadlock due to page faults during direct IO reads and writes

Pull nfsd updates from Bruce Fields:
 "A slow cycle for nfsd: mainly cleanup, including Neil's patch dropping
  support for a filehandle format deprecated 20 years ago, and further
  xdr-related cleanup from Chuck"

* tag 'nfsd-5.16' of git://linux-nfs.org/~bfields/linux: (26 commits)
  nfsd4: remove obselete comment
  nfsd: document server-to-server-copy parameters
  NFSD:fix boolreturn.cocci warning
  nfsd: update create verifier comment
  SUNRPC: Change return value type of .pc_encode
  SUNRPC: Replace the "__be32 *p" parameter to .pc_encode
  NFSD: Save location of NFSv4 COMPOUND status
  SUNRPC: Change return value type of .pc_decode
  SUNRPC: Replace the "__be32 *p" parameter to .pc_decode
  SUNRPC: De-duplicate .pc_release() call sites
  SUNRPC: Simplify the SVC dispatch code path
  SUNRPC: Capture value of xdr_buf::page_base
  SUNRPC: Add trace event when alloc_pages_bulk() makes no progress
  svcrdma: Split svcrmda_wc_{read,write} tracepoints
  svcrdma: Split the svcrdma_wc_send() tracepoint
  svcrdma: Split the svcrdma_wc_receive() tracepoint
  NFSD: Have legacy NFSD WRITE decoders use xdr_stream_subsegment()
  SUNRPC: xdr_stream_subsegment() must handle non-zero page_bases
  NFSD: Initialize pointer ni with NULL and not plain integer 0
  NFSD: simplify struct nfsfh
  ...

Pull NFS client updates from Trond Myklebust:
 "Highlights include:

  Features:
   - NFSv4.1 can always retrieve and cache the ACCESS mode on OPEN
   - Optimisations for READDIR and the 'ls -l' style workload
   - Further replacements of dprintk() with tracepoints and other
     tracing improvements
   - Ensure we re-probe NFSv4 server capabilities when the user does a
     "mount -o remount"

  Bugfixes:
   - Fix an Oops in pnfs_mark_request_commit()
   - Fix up deadlocks in the commit code
   - Fix regressions in NFSv2/v3 attribute revalidation due to the
     change_attr_type optimisations
   - Fix some dentry verifier races
   - Fix some missing dentry verifier settings
   - Fix a performance regression in nfs_set_open_stateid_locked()
   - SUNRPC was sending multiple SYN calls when re-establishing a TCP
     connection.
   - Fix multiple NFSv4 issues due to missing sanity checking of server
     return values
   - Fix a potential Oops when FREE_STATEID races with an unmount

  Cleanups:
   - Clean up the labelled NFS code
   - Remove unused header <linux/pnfs_osd_xdr.h>"

* tag 'nfs-for-5.16-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (84 commits)
  NFSv4: Sanity check the parameters in nfs41_update_target_slotid()
  NFS: Remove the nfs4_label argument from decode_getattr_*() functions
  NFS: Remove the nfs4_label argument from nfs_setsecurity
  NFS: Remove the nfs4_label argument from nfs_fhget()
  NFS: Remove the nfs4_label argument from nfs_add_or_obtain()
  NFS: Remove the nfs4_label argument from nfs_instantiate()
  NFS: Remove the nfs4_label from the nfs_setattrres
  NFS: Remove the nfs4_label from the nfs4_getattr_res
  NFS: Remove the f_label from the nfs4_opendata and nfs_openres
  NFS: Remove the nfs4_label from the nfs4_lookupp_res struct
  NFS: Remove the label from the nfs4_lookup_res struct
  NFS: Remove the nfs4_label from the nfs4_link_res struct
  NFS: Remove the nfs4_label from the nfs4_create_res struct
  NFS: Remove the nfs4_label from the nfs_entry struct
  NFS: Create a new nfs_alloc_fattr_with_label() function
  NFS: Always initialise fattr->label in nfs_fattr_alloc()
  NFSv4.2: alloc_file_pseudo() takes an open flag, not an f_mode
  NFS: Don't allocate nfs_fattr on the stack in __nfs42_ssc_open()
  NFSv4: Remove unnecessary 'minor version' check
  NFSv4: Fix potential Oops in decode_op_map()
  ...

Merge branch 'exit-cleanups-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace

Pull exit cleanups from Eric Biederman:
 "While looking at some issues related to the exit path in the kernel I
  found several instances where the code is not using the existing
  abstractions properly.

  This set of changes introduces force_fatal_sig a way of sending a
  signal and not allowing it to be caught, and corrects the misuse of
  the existing abstractions that I found.

  A lot of the misuse of the existing abstractions are silly things such
  as doing something after calling a no return function, rolling BUG by
  hand, doing more work than necessary to terminate a kernel thread, or
  calling do_exit(SIGKILL) instead of calling force_sig(SIGKILL).

  In the review a deficiency in force_fatal_sig and force_sig_seccomp
  where ptrace or sigaction could prevent the delivery of the signal was
  found. I have added a change that adds SA_IMMUTABLE to change that
  makes it impossible to interrupt the delivery of those signals, and
  allows backporting to fix force_sig_seccomp

  And Arnd found an issue where a function passed to kthread_run had the
  wrong prototype, and after my cleanup was failing to build."

* 'exit-cleanups-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (23 commits)
  soc: ti: fix wkup_m3_rproc_boot_thread return type
  signal: Add SA_IMMUTABLE to ensure forced siganls do not get changed
  signal: Replace force_sigsegv(SIGSEGV) with force_fatal_sig(SIGSEGV)
  exit/r8188eu: Replace the macro thread_exit with a simple return 0
  exit/rtl8712: Replace the macro thread_exit with a simple return 0
  exit/rtl8723bs: Replace the macro thread_exit with a simple return 0
  signal/x86: In emulate_vsyscall force a signal instead of calling do_exit
  signal/sparc32: In setup_rt_frame and setup_fram use force_fatal_sig
  signal/sparc32: Exit with a fatal signal when try_to_clear_window_buffer fails
  exit/syscall_user_dispatch: Send ordinary signals on failure
  signal: Implement force_fatal_sig
  exit/kthread: Have kernel threads return instead of calling do_exit
  signal/s390: Use force_sigsegv in default_trap_handler
  signal/vm86_32: Properly send SIGSEGV when the vm86 state cannot be saved.
  signal/vm86_32: Replace open coded BUG_ON with an actual BUG_ON
  signal/sparc: In setup_tsb_params convert open coded BUG into BUG
  signal/powerpc: On swapcontext failure force SIGSEGV
  signal/sh: Use force_sig(SIGKILL) instead of do_group_exit(SIGKILL)
  signal/mips: Update (_save|_restore)_fp_context to fail with -EFAULT
  signal/sparc32: Remove unreachable do_exit in do_sparc_fault
  ...

Pull prctl updates from Christian Brauner:
 "This contains the missing prctl uapi pieces for PR_SCHED_CORE.

  In order to activate core scheduling the caller is expected to specify
  the scope of the new core scheduling domain.

  For example, passing 2 in the 4th argument of

     prctl(PR_SCHED_CORE, PR_SCHED_CORE_CREATE, <pid>,  2, 0);

  would indicate that the new core scheduling domain encompasses all
  tasks in the process group of <pid>. Specifying 0 would only create a
  core scheduling domain for the thread identified by <pid> and 2 would
  encompass the whole thread-group of <pid>.

  Note, the values 0, 1, and 2 correspond to PIDTYPE_PID, PIDTYPE_TGID,
  and PIDTYPE_PGID. A first version tried to expose those values
  directly to which I objected because:

   - PIDTYPE_* is an enum that is kernel internal which we should not
     expose to userspace directly.

   - PIDTYPE_* indicates what a given struct pid is used for it doesn't
     express a scope.

  But what the 4th argument of PR_SCHED_CORE prctl() expresses is the
  scope of the operation, i.e. the scope of the core scheduling domain
  at creation time. So Eugene's patch now simply introduces three new
  defines PR_SCHED_CORE_SCOPE_THREAD, PR_SCHED_CORE_SCOPE_THREAD_GROUP,
  and PR_SCHED_CORE_SCOPE_PROCESS_GROUP. They simply express what
  happens.

  This has been on the mailing list for quite a while with all relevant
  scheduler folks Cced. I announced multiple times that I'd pick this up
  if I don't see or her anyone else doing it. None of this touches
  proper scheduler code but only concerns uapi so I think this is fine.

  With core scheduling being quite common now for vm managers (e.g.
  moving individual vcpu threads into their own core scheduling domain)
  and container managers (e.g. moving the init process into its own core
  scheduling domain and letting all created children inherit it) having
  to rely on raw numbers passed as the 4th argument in prctl() is a bit
  annoying and everyone is starting to come up with their own defines"

* tag 'kernel.sys.v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  uapi/linux/prctl: provide macro definitions for the PR_SCHED_CORE type argument

Pull pidfd updates from Christian Brauner:
 "Various places in the kernel have picked up pidfds.

  The two most recent additions have probably been the ability to use
  pidfds in bpf maps and the usage of pidfds in mm-based syscalls such
  as process_mrelease() and process_madvise().

  The same pattern to turn a pidfd into a struct task exists in two
  places. One of those places used PIDTYPE_TGID while the other one used
  PIDTYPE_PID even though it is clearly documented in all pidfd-helpers
  that pidfds __currently__ only refer to thread-group leaders (subject
  to change in the future if need be).

  This isn't a bug per se but has the potential to be one if we allow
  pidfds to refer to individual threads. If that happens we want to
  audit all codepaths that make use of them to ensure they can deal with
  pidfds refering to individual threads.

  This adds a simple helper to turn a pidfd into a struct task making it
  easy to grep for such places. Plus, it gets rid of code-duplication"

* tag 'pidfd.v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  mm: use pidfd_get_task()
  pid: add pidfd_get_task() helper

Pull more thermal control updates from Rafael Wysocki:
 "These fix two issues in the thermal core and one in the int340x
  thermal driver.

  Specifics:

   - Replace pr_warn() with pr_warn_once() in user_space_bind() to
     reduce kernel log noise (Rafael Wysocki).

   - Extend the RFIM mailbox interface in the int340x thermal driver to
     return 64 bit values to allow all values returned by the hardware
     to be handled correctly (Srinivas Pandruvada).

   - Fix possible NULL pointer dereferences in the of_thermal_ family of
     functions (Subbaraman Narayanamurthy)"

* tag 'thermal-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  thermal: Replace pr_warn() with pr_warn_once() in user_space_bind()
  thermal: Fix NULL pointer dereferences in of_thermal_ functions
  thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses

Pull more power management updates from Rafael Wysocki:
 "These fix three intel_pstate driver regressions, fix locking in the
  core code suspending and resuming devices during system PM
  transitions, fix the handling of cpuidle drivers based on runtime PM
  during system-wide suspend, fix two issues in the operating
  performance points (OPP) framework and resource-managed helpers to it.

  Specifics:

   - Fix two intel_pstate driver regressions related to the HWP
     interrupt handling added recently (Srinivas Pandruvada).

   - Fix intel_pstate driver regression introduced during the 5.11 cycle
     and causing HWP desired performance to be mishandled in some cases
     when switching driver modes and during system suspend and shutdown
     (Rafael Wysocki).

   - Fix system-wide device suspend and resume locking to avoid
     deadlocks when device objects are deleted during a system-wide PM
     transition (Rafael Wysocki).

   - Modify system-wide suspend of devices to prevent cpuidle drivers
     based on runtime PM from misbehaving during the "no IRQ" phase of
     it (Ulf Hansson).

   - Fix return value of _opp_add_static_v2() helper (YueHaibing).

   - Fix required-opp handle count (Pavankumar Kondeti).

   - Add resource managed OPP helpers, update dev_pm_opp_attach_genpd(),
     update their devfreq users, and make minor DT binding change
     (Dmitry Osipenko)"

* tag 'pm-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: sleep: Avoid calling put_device() under dpm_list_mtx
  cpufreq: intel_pstate: Clear HWP Status during HWP Interrupt enable
  cpufreq: intel_pstate: Fix unchecked MSR 0x773 access
  cpufreq: intel_pstate: Clear HWP desired on suspend/shutdown and offline
  PM: sleep: Fix runtime PM based cpuidle support
  dt-bindings: opp: Allow multi-worded OPP entry name
  opp: Fix return in _opp_add_static_v2()
  PM / devfreq: tegra30: Check whether clk_round_rate() returns zero rate
  PM / devfreq: tegra30: Use resource-managed helpers
  PM / devfreq: Add devm_devfreq_add_governor()
  opp: Add more resource-managed variants of dev_pm_opp_of_add_table()
  opp: Change type of dev_pm_opp_attach_genpd(names) argument
  opp: Fix required-opps phandle array count check

Pull more ACPI updates from Rafael Wysocki:
 "These add support for a new ACPI device configuration object called
  _DSC, fix some issues including one recent regression, add two new
  items to quirk lists and clean up assorted pieces of code.

  Specifics:

   - Add support for new ACPI device configuration object called _DSC
     ("Deepest State for Configuration") to allow certain devices to be
     probed without changing their power states, document it and make
     two drivers use it (Sakari Ailus, Rajmohan Mani).

   - Fix device wakeup power reference counting broken recently by
     mistake (Rafael Wysocki).

   - Drop unused symbol and macros depending on it from acgcc.h (Rafael
     Wysocki).

   - Add HP ZHAN 66 Pro to the "no EC wakeup" quirk list (Binbin Zhou).

   - Add Xiaomi Mi Pad 2 to the backlight quirk list and drop an unused
     piece of data from all of the list entries (Hans de Goede).

   - Fix register read accesses handling in the Intel PMIC operation
     region driver (Hans de Goede).

   - Clean up static variables initialization in the EC driver
     (wangzhitong)"

* tag 'acpi-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Documentation: ACPI: Fix non-D0 probe _DSC object example
  ACPI: Drop ACPI_USE_BUILTIN_STDARG ifdef from acgcc.h
  ACPI: PM: Fix device wakeup power reference counting error
  ACPI: video: use platform backlight driver on Xiaomi Mi Pad 2
  ACPI: video: Drop dmi_system_id.ident settings from video_detect_dmi_table[]
  ACPI: PMIC: Fix intel_pmic_regs_handler() read accesses
  ACPI: EC: Remove initialization of static variables to false
  ACPI: EC: Use ec_no_wakeup on HP ZHAN 66 Pro
  at24: Support probing while in non-zero ACPI D state
  media: i2c: imx319: Support device probe in non-zero ACPI D state
  ACPI: Add a convenience function to tell a device is in D0 state
  Documentation: ACPI: Document _DSC object usage for enum power state
  i2c: Allow an ACPI driver to manage the device's power state during probe
  ACPI: scan: Obtain device's desired enumeration power state

Pull dmaengine updates from Vinod Koul:
 "A bunch of driver updates, no new driver or controller support this
  time though:

   - Another pile of idxd updates

   - pm routines cleanup for at_xdmac driver

   - Correct handling of callback_result for few drivers

   - zynqmp_dma driver updates and descriptor management refinement

   - Hardware handshaking support for dw-axi-dmac

   - Support for remotely powered controllers in Qcom bam dma

   - tegra driver updates"

* tag 'dmaengine-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (69 commits)
  dmaengine: ti: k3-udma: Set r/tchan or rflow to NULL if request fail
  dmaengine: ti: k3-udma: Set bchan to NULL if a channel request fail
  dmaengine: stm32-dma: avoid 64-bit division in stm32_dma_get_max_width
  dmaengine: fsl-edma: support edma memcpy
  dmaengine: idxd: fix resource leak on dmaengine driver disable
  dmaengine: idxd: cleanup completion record allocation
  dmaengine: zynqmp_dma: Correctly handle descriptor callbacks
  dmaengine: xilinx_dma: Correctly handle cyclic descriptor callbacks
  dmaengine: altera-msgdma: Correctly handle descriptor callbacks
  dmaengine: at_xdmac: fix compilation warning
  dmaengine: dw-axi-dmac: Simplify assignment in dma_chan_pause()
  dmaengine: qcom: bam_dma: Add "powered remotely" mode
  dt-bindings: dmaengine: bam_dma: Add "powered remotely" mode
  dmaengine: sa11x0: Mark PM functions as __maybe_unused
  dmaengine: switch from 'pci_' to 'dma_' API
  dmaengine: ioat: switch from 'pci_' to 'dma_' API
  dmaengine: hsu: switch from 'pci_' to 'dma_' API
  dmaengine: hisi_dma: switch from 'pci_' to 'dma_' API
  dmaengine: dw: switch from 'pci_' to 'dma_' API
  dmaengine: dw-edma-pcie: switch from 'pci_' to 'dma_' API
  ...