Factor out gfar_hw_init() to contain all the controller hw
initialization steps for a better control of register writes,
and to significantly simplify the tangled code from gfar_probe().
This results in code size and stack usage reduction (besides
code readability).

Fix memory leak on device removal, by freeing the rx_/tx_queue
structures.

Replace custom bit swapping function with a library one (bitrev8).

Move allocation of rx_/tx_queue struct arrays before the group
structure init, because in order to assign Rx/Tx queues
to groups we need to have the queues first.  This also allows
earlier bail out of gfar_probe(), in case the memory allocation
fails.

The flow control checks for maccfg1 were removed from gfar_probe(),
since flow control is disabled at probe time (priv->rx_/tx_pause_en
are 0). Redundant initializations (by 0) also removed.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

linux/sctp.h was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ERROR: spaces required and "(foo*)" should be "(foo *)"
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace two magic numbers which intialize clgstate::state.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phoebe Buckheister says:

====================
ieee802154: support rf212 and extended mac features

this patch set adds support for the RF212 radio chip to the existing
at86rf230 driver and adds support for numerous features of the RF212
chips to the ieee802154 stack. These features include CSMA parameter
configuration, transmit power control, CCA parameter configuration, and
automatic retransmission of frames. Netlink APIs are provided for all
new options introduced in this set.

Many features might also work for RF230, but since I have no such chips
at my disposal, most new features are implemented only for RF212.

Changes since v2:
 * Indentation
Changes since v1:
 * CodingStyle compliance. Thanks Sergei Shtylyov
 * Add CSMA parameters to netlink phy list that were forgotten in v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch does multiple things:

 * add .set_csma_params and .set_frame_retries for the RF212 radio.
   This should work fine with RF230, but since I have no RF230 radios to
   test with, RF230 does not implement these right now
 * enable TX_ARET for frame retransmission limits greater than -1

Since RF230 has no operations to change CSMA parameters or frame retry
limits, RF230 will not be able to enter TX_ARET with this patch.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce new netlink attributes for SET_PHY_ATTRS:
 * CSMA minimal backoff exponent
 * CSMA maximal backoff exponent
 * CSMA retry limit
 * frame retransmission limit

The CSMA attributes shall correspond to minBE, maxBE and maxCSMABackoffs of
802.15.4, respectively. The frame retransmission shall correspond to
maxFrameRetries of 802.15.4, unless given as -1: then the old behaviour
of the stack shall apply. For RF2xy, the old behaviour is to not do
channel sensing at all and simply send *right now*, which is not
intended behaviour for most applications and actually prohibited for
some channel/page combinations.

For all values except frame retransmission limit, the defaults of
802.15.4 apply. Frame retransmission limits are set to -1 to indicate
backward-compatible behaviour.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

A documented erratum of the RF212 chip describes that some versions of
RF212 may not be properly reset by the standard reset procedure. The
described workaround seems to not fully work either; my RF212 chips will
not correctly receive any frames unless they are taken from RX mode to
TRX_OFF and back to RX mode, effectively forcing a up-down-up-cycle.
Going to TRX_OFF and to RX without intermediate state changes at least
once fixes this.

The same transition is allowed for RF230, so simply do it all the time.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.

For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The standard assigns channel 0 on page 2 to be 100kbps QPSK in the
868.3MHz band. Add support to the at86rf230 driver for this channel and
page, at the moment predicated only for the RF212 chip.

Per the datasheet, configurations for page 0, channels 0 to 10 and page
2, channels 0 to 10 differ only in the BPSK_QPSK bit. Support for
channels 1 to 10 is untested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.

This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current IEEE802.15.4 stack assumes that a radio will never deliver
packets with a bad CRC into the stack, as required by the standard.
at86rf230 driven radios violates this assumption because of another
incompatibility: devices are required to send ACKs if requested by a
sender, but RF2xx will only send ACKs from a special receive mode that
is currently not used by the driver.

Enable this receive mode to fix both bugs. Frames with bad CRCs will not
be received at all, and ACKs will be sent if so requested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the AT86RF2xy chips are mostly compatible, this is only a small
change to the actual driver code. The at86rf230 driver already supports the
RF212 in most places, only three small adjustments are required:

 * force the initial state after P_ON to FORCE_TRX_OFF to work around a
   documented erratum
 * channels_supported depends on the frequency of the transceiver, and
   thus is_rf212
 * do early detection of chip version select an appropriate _ops struct
   based on the chip version.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: soft reset rework for 10G PHYs

As reported by Shaohui, 10G PHYs may have a slightly more complex reset
sequence for which a BMCR_RESET software reset might not suffice. This
patchset offers a solution for those by allowing them to implement their
own soft_reset() callback. Finally there is an update to the PHY library
Documentation to cover for the newly added callbacks of the PHY driver
structure.

Changes in v2:
- fixed callback testing
- fixed typo in Documentation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY library was missing a bunch of newly added PHY driver callbacks
along with a smallish description of what they do, fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As pointed out by Shaohui, most 10G PHYs out there have a non-standard
compliant software reset sequence, eventually something much more
complex than just toggling the BMCR_RESET bit. Allow PHY driver to
implement their own soft_reset() callback to deal with that. If no
callback is provided, call into genphy_soft_reset() which makes sure the
existing behavior is kept intact.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As pointed out by Shaohui, this function is generic for 10/100/1000
PHYs, but 10G PHYs might have a slightly different reset sequence which
prevents most of them from using this function.

Move the BMCR_RESET based software resent sequence to
genphy_soft_reset() in preparation for allowing PHY drivers to implement
a soft_reset() callback.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of the buffer allocation in the receive path for normal packets.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the receive path a little more efficient by parameterizing the
required state rather than re-establishing that state.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This structure is redundant; get rid of it make the code little more efficient -
get rid of the unnecessary indirection.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows the use of a generic timestamping phy connected
to the cpsw if CPTS support is not enabled. This also adds support
of the SIOCGMIIREG and SIOCSMIIREG, and moves handling of SIOCGMIIPHY
to the generic driver.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

ether_addr_copy is smaller and faster for some architectures.

This relies on a stack frame being at least __aligned(2)
for one use of an Ethernet address on the stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Neatening only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing terminating newlines.
Convert uses of pr_info to pr_cont in bond_check_params.
Standardize upper/lower case styles.
Typo fixes, remove unnecessary parentheses and periods.
Alignment neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use more current logging style.

Coalesce formats, realign arguments, drop unnecessary periods.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On success, the function netdev_alloc_skb initializes the dev field of its
result to its first argument, so this doesn't have to be done in the
calling context.

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression skb,privn,e;
@@

skb = netdev_alloc_skb(privn,...);
... when strict
(
-skb->dev = privn;
|
?skb = e
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document the required "clocks" phandles and their corresponding
"clock-names" properties for the two clocks used by the GENET hardware
block ("enet" and "enet-wol").

CC: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I commit e099e86c
("tipc: add node_lock protection to link lookup function")
we are calling spin_lock(&node->lock) directly instead of indirectly
via the tipc_node_lock(node) function. However, tipc_node_lock() is
using spin_lock_bh(), not spin_lock(), something leading to
unbalanced usage in one place, and a smatch warning.

We fix this by consistently using tipc_node_lock()/unlock() in
in the places touched by the mentioned commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 7d33939f
("tipc: delay delete of link when failover is needed") we
introduced a loop for finding and removing a link pointer
in an array. The removal is done after we have left the loop,
giving the impression that one may remove the wrong pointer
if no matching element is found.

This is not really a bug, since we know that there will always
be a matching element, but it looks wrong, and causes a smatch
warning.

We fix this loop with this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently this always returns ENOBUFS, because the return value of
__ip_tunnel_create is discarded.

A more common failure is a duplicate name (EEXIST).  Propagate the real
error code so userspace can display a more meaningful error message.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Openvswitch defines u64_stats_sync as ->sync rather than ->syncp,
so fails to compile with netdev_alloc_pcpu_stats(). So just rename it to ->syncp.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 1c213bd2 (net: introduce netdev_alloc_pcpu_stats() for drivers)
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>