- 19 May, 2014 1 commit
-
- 14 May, 2014 4 commits
-
-
Rajkumar Manoharan authored
During remain on channel request, ANI worker thread is not stopped before doing hw reset. This is causing kernel crash in hw_per_calibration. This change ensures that ANI is stopped before doing chip reset and it will be rescheduled later when the chip is configured back to home channel and having valid bss. Reported-by: David Herrmann <dh.herrmann@gmail.com> Tested-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
-
Samuel Ortiz authored
0466 was probably meant to be 0644, there's no reason why everyone except root could write there. Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
-
Johannes Berg authored
Jouni reported that if a remain-on-channel was active on the same channel as the current operating channel, then the ROC would start, but any frames transmitted using mgmt-tx on the same channel would get delayed until after the ROC. The reason for this is that the ROC starts, but doesn't have any handling for "remain on the same channel", so it stops the interface queues. The later mgmt-tx then puts the frame on the interface queues (since it's on the current operating channel) and thus they get delayed until after the ROC. To fix this, add some logic to handle remaining on the same channel specially and not stop the queues etc. in this case. This not only fixes the bug but also improves behaviour in this case as data frames etc. can continue to flow. Cc: stable@vger.kernel.org Reported-by: Jouni Malinen <j@w1.fi> Tested-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
- 13 May, 2014 5 commits
-
-
Johannes Berg authored
My commit removing that also removed it from the header file which can break compilation of userspace that needed it, add it back for API/ABI compatibility purposes (but no code to implement anything for it.) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
David Spinadel authored
Prevent sched scan while not idle (including during association or in AP mode) instead of while associated only. This fixes my previous commit which was incomplete: commit bd5e4744 Author: David Spinadel <david.spinadel@intel.com> Date: Thu Apr 24 13:15:29 2014 +0300 iwlwifi: mvm: do no sched scan while associated Currently the FW doesn't support sched scan while associated, Prevent it. Signed-off-by: David Spinadel <david.spinadel@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
Emmanuel Grumbach authored
If the association is in progress while we suspend, the stack will be in a messed up state. Clean it before we suspend. This patch completes Johannes's patch: 1a1cb744 Author: Johannes Berg <johannes.berg@intel.com> mac80211: fix suspend vs. authentication race Cc: <stable@vger.kernel.org> Fixes: 12e7f517 ("mac80211: cleanup generic suspend/resume procedures") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Eliad Peller authored
tail should be equal to the last valid index, so decrease it by one. This error causes in "a gap" in some cases (as well as some possible out-of-bound write), finally resulting in ucode assertion. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
- 12 May, 2014 2 commits
-
-
Daniel Kim authored
Fix iovar 'bw_cap' set command failure introduced by commit ff3b0fba6f25555ef59c55d138a467d0f81d82d7 Author: Arend van Spriel <arend@broadcom.com> Date: Sat Mar 15 12:00:57 2014 +0100 brcmfmac: fallback to mimo_bw_cap for older firmwares This resulted in disabling 20MHz operation in the firmware. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Daniel Kim <dekim@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
-
- 11 May, 2014 1 commit
-
-
Emmanuel Grumbach authored
There was a deadlock in monitor mode when we were setting the channel if the channel was not 1. ====================================================== [ INFO: possible circular locking dependency detected ] 3.14.3 #4 Not tainted ------------------------------------------------------- iw/3323 is trying to acquire lock: (&local->chanctx_mtx){+.+.+.}, at: [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211] but task is already holding lock: (&local->iflist_mtx){+.+...}, at: [<ffffffffa0609e0a>] ieee80211_set_monitor_channel+0x5a/0x1b0 [mac80211] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&local->iflist_mtx){+.+...}: [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa0518189>] iwl_mvm_recalc_multicast+0x49/0xa0 [iwlmvm] [<ffffffffa051822e>] iwl_mvm_configure_filter+0x4e/0x70 [iwlmvm] [<ffffffffa05e6d43>] ieee80211_configure_filter+0x153/0x5f0 [mac80211] [<ffffffffa05e71f5>] ieee80211_reconfig_filter+0x15/0x20 [mac80211] [snip] -> #1 (&mvm->mutex){+.+.+.}: [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa0517246>] iwl_mvm_add_chanctx+0x56/0xe0 [iwlmvm] [<ffffffffa062ca1e>] ieee80211_new_chanctx+0x13e/0x410 [mac80211] [<ffffffffa062d953>] ieee80211_vif_use_channel+0x1c3/0x5a0 [mac80211] [<ffffffffa06035ab>] ieee80211_add_virtual_monitor+0x1ab/0x6b0 [mac80211] [<ffffffffa06052ea>] ieee80211_do_open+0xe6a/0x15a0 [mac80211] [<ffffffffa0605a79>] ieee80211_open+0x59/0x60 [mac80211] [snip] -> #0 (&local->chanctx_mtx){+.+.+.}: [<ffffffff810d6cb7>] check_prevs_add+0x977/0x980 [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211] [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211] [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211] [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211] [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211] [snip] other info that might help us debug this: Chain exists of: &local->chanctx_mtx --> &mvm->mutex --> &local->iflist_mtx Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&local->iflist_mtx); lock(&mvm->mutex); lock(&local->iflist_mtx); lock(&local->chanctx_mtx); *** DEADLOCK *** This deadlock actually occurs: INFO: task iw:3323 blocked for more than 120 seconds. Not tainted 3.14.3 #4 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. iw D ffff8800c8afcd80 4192 3323 3322 0x00000000 ffff880078fdb7e0 0000000000000046 ffff8800c8afcd80 ffff880078fdbfd8 00000000001d5540 00000000001d5540 ffff8801141b0000 ffff8800c8afcd80 ffff880078ff9e38 ffff880078ff9e38 ffff880078ff9e40 0000000000000246 Call Trace: [<ffffffff817ea841>] schedule_preempt_disabled+0x31/0x80 [<ffffffff817ebaed>] mutex_lock_nested+0x19d/0x4f0 [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa052a680>] ? iwl_mvm_power_mac_update_mode+0xc0/0xc0 [iwlmvm] [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa0529357>] _iwl_mvm_power_update_binding+0x27/0x80 [iwlmvm] [<ffffffffa0516eb1>] iwl_mvm_unassign_vif_chanctx+0x81/0xc0 [iwlmvm] [<ffffffffa062d3ff>] __ieee80211_vif_release_channel+0xdf/0x470 [mac80211] [<ffffffffa062e2fa>] ieee80211_vif_release_channel+0x4a/0xb0 [mac80211] [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211] [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211] [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211] [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211] This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75541 Cc: <stable@vger.kernel.org> [3.13+] Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 09 May, 2014 2 commits
-
-
Eliad Peller authored
If sdata doesn't have a valid dev (e.g. in case of monitor vif), the vif_name field was initialized with (a length of) some short string, but later was set to a different, potentially larger one. This resulted in out-of-bounds write, which usually appeared as garbage in the trace log. Simply trace sdata->name, as it should always have the correct name for both cases. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
There are two (related) issues with this. One case, reported by Michal, is related to hostap: it unsets the 20/40 capability bit for stations that associate when it's in 20 MHz mode. The other case, reported by Eyal, is that some APs like Netgear R6300v2 and probably others based on the BCM4360 chipset can be configured for doing VHT at 20Mhz. In this case the beacon has a VHT IE but the HT cap indicates transmitter only support 20Mhz. In both of these cases, we currently avoid VHT and use only HT this means we can't use the highest rates (MCS8), so fixing this leads to throughput improvements. Reported-by: Michal Kazior <michal.kazior@tieto.com> Reported-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
- 08 May, 2014 1 commit
-
- 07 May, 2014 1 commit
-
-
Emmanuel Grumbach authored
In case RFKILL is in KILL position, the NIC will issue an interrupt straight away. This interrupt won't be sent because it is masked in the hardware. But if our interrupt service routine is called for another reason (SHARED_IRQ), then we'll look at the interrupt cause and service it. This can cause bad things if we are not ready yet. Explicitly clean the interrupt cause register to make sure we won't service anything before we are ready to. Cc: <stable@vger.kernel.org> [3.14] Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 06 May, 2014 4 commits
-
-
David Spinadel authored
Currently the FW doesn't support sched scan while associated, Prevent it. Signed-off-by: David Spinadel <david.spinadel@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
-
Emmanuel Grumbach authored
My bad - I forgot to update this when sending the patch upstream. Fixes: 87d5e415 ("iwlwifi: mvm: rs: reinit rs if no tx for a long time") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
Emmanuel Grumbach authored
The commit below introduced a bug in the validity bits in init. Due to that, all the Coex mechanism stopped sending kills to the BT side. Fix that. Fixes: b9fae2d5 ("iwlwifi: mvm: BT Coex add support for Co-running block") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 05 May, 2014 4 commits
-
-
Eliad Peller authored
ieee80211_reconfig already holds rtnl, so calling cfg80211_sched_scan_stopped results in deadlock. Use the rtnl-version of this function instead. Fixes: d43c6b6e ("mac80211: reschedule sched scan after HW restart") Cc: stable@vger.kernel.org (3.14+) Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Eliad Peller authored
Add locked-version for cfg80211_sched_scan_stopped. This is used for some users that might want to call it when rtnl is already locked. Fixes: d43c6b6e ("mac80211: reschedule sched scan after HW restart") Cc: stable@vger.kernel.org (3.14+) Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Eliad Peller authored
cfg80211 is notified about connection failures by __cfg80211_connect_result() call. However, this function currently does not free cfg80211 sme. This results in hanging connection attempts in some cases e.g. when mac80211 authentication attempt is denied, we have this function call: ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() -> cfg80211_process_auth() -> cfg80211_sme_rx_auth() -> __cfg80211_connect_result() but cfg80211_sme_free() is never get called. Fixes: ceca7b71 ("cfg80211: separate internal SME implementation") Cc: stable@vger.kernel.org (3.10+) Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Henning Rogge authored
Filter out incoming multicast packages before applying their bitrate to the rx bitrate station info field to prevent them from setting the rx bitrate to the basic multicast rate. Signed-off-by: Henning Rogge <hrogge@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
- 30 Apr, 2014 4 commits
-
-
Ben Hutchings authored
Fixes: a53268be ('rtlwifi: rtl8192cu: Fix too long disable of IRQs') Cc: stable@vger.kernel.org Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Larry Finger authored
Beginning with kernel 3.13, this driver fails on some systems. The problem was bisected to: Commit 1bf4bbb4 Author: Felix Fietkau <nbd@openwrt.org> Title: mac80211: send control port protocol frames to the VO queue There is noting wrong with the above commit. The regression occurs because V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to modify the rtl8192se routine that sets the correct transmit queue. Bug: https://bugzilla.kernel.org/show_bug.cgi?id=74541Reported-by: Alex Miller <almiller_1@yahoo.co.uk> Tested-by: Alex Miller <almiller_1@yahoo.co.uk> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.13+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
There are some corner cases where the driver could get stuck with a full tid queue that is paused, leading to a software tx queue hang. Since the tx queueing rework, pausing per-tid queues on aggregation session setup is no longer necessary. The driver will assign sequence numbers to buffered frames when a new session is established, in order to get the correct starting sequence number. mac80211 prevents new frames from entering the queue during setup. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
When the amount of noise fluctuates strongly, low immunity settings can sometimes disrupt signal detection on AR913x chips. When that happens, no OFDM/CCK errors are reported anymore, and ANI tunes the radio to the lowest immunity settings. Usually rx/tx fails as well in that case. To fix this, keep noise immunity settings at or above ANI default level, which will keep radio parameters at or above INI values. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 25 Apr, 2014 7 commits
-
-
Mohammed Habibulla authored
Add support for the AR9462 chip T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3007 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Mohammed Habibulla <moch@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
-
Johan Hedberg authored
When we're performing reauthentication (in order to elevate the security level from an unauthenticated key to an authenticated one) we do not need to issue any encryption command once authentication completes. Since the trigger for the encryption HCI command is the ENCRYPT_PEND flag this flag should not be set in this scenario. Instead, the REAUTH_PEND flag takes care of all necessary steps for reauthentication. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
-
Johan Hedberg authored
Commit 1c2e0041 introduced an event handler for the encryption key refresh complete event with the intent of fixing some LE/SMP cases. However, this event is shared with BR/EDR and there we actually want to act only on the auth_complete event (which comes after the key refresh). If we do not do this we may trigger an L2CAP Connect Request too early and cause the remote side to return a security block error. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
-
Marcel Holtmann authored
This reverts commit d2bee8fb. Enabling autosuspend for Intel Bluetooth devices has been shown to not work reliable. It does work for some people with certain combinations of USB host controllers, but for others it puts the device to sleep and it will not wake up for any event. These events can be important ones like HCI Inquiry Complete or HCI Connection Request. The events will arrive as soon as you poke the device with a new command, but that is not something we can do in these cases. Initially there were patches to the xHCI USB controller that fixed this for some people, but not for all. This could be well a problem somewhere in the USB subsystem or in the USB host controllers or just plain a hardware issue somewhere. At this moment we just do not know and the only safe action is to revert this patch. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: Tedd Ho-Jeong An <tedd.an@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
-
Hans de Goede authored
brcmfmac has been broken on my cubietruck with a BCM43362: brcmfmac: brcmf_chip_recognition: found AXI chip: BCM43362, rev=1 brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d since commit 53036261: "brcmfmac: update core reset and disable routines". The problem is that since this commit brcmf_chip_ai_resetcore no longer sets BCMA_IOCTL itself before bringing the core out of reset, instead relying on brcmf_chip_ai_coredisable to do so. But brcmf_chip_ai_coredisable is a nop of the chip is already in reset. This patch modifies brcmf_chip_ai_coredisable to always set BCMA_IOCTL even if the core is already in reset. This fixes brcmfmac hanging in firmware loading on my board. Cc: stable@vger.kernel.org # v3.14 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
The commit "ath9k: move sc_flags to ath_common" moved setting ATH_OP_INVALID flag below ieee80211_register_hw. This is causing the flag never being cleared randomly as the drv_start is called prior to setting flag. Fix this by setting the flag prior to register_hw. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
- 22 Apr, 2014 4 commits
-
-
Tim Harvey authored
Implement a recv budget so that in cases of high traffic we still allow other taskets to get processed. Without this, we can encounter a host of issues during high wireless traffic reception depending on system load including rcu stall's detected (ARM), soft lockups, failure to service critical tasks such as watchdog resets, and triggering of the tx stuck tasklet. The same thing was proposed previously by Ben: http://www.spinics.net/lists/linux-wireless/msg112891.html The only difference here is that I make sure only processed packets are counted in the budget by checking at the end of the rx loop. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Tim Harvey authored
If a flush is requested, make sure to clear the descriptor once we've processed it. This resolves a hang that will occur if all RX descriptors are full when a flush is requested. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Colin Ian King authored
static code analysis from cppcheck reports: [drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:322]: (error) Uninitialized variable: packet_beacon packet_beacon is not initialized and hence packet_beacon contains garbage from the stack, so set it to false. Signed-off-by: Colin Ian King <colin.king@canonical.com> Cc: Stable <stable@vger.kernel.org> [3.10+] Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
Let's formalize what must have been blatantly clear from my level of activity is the past year(s). I simply do not have time for this anymore. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-