loops in ide_cdrom_init()/ide_cdrom_exit(), etc. are pulled into
ide_register_module()/ide_unregister_module() resp.

Duplicate calls of ide_cdrom_init(), idedisk_init(), etc. are removed
from ide_init_builtin_drivers() (they were called both from there (i.e.
from ide_init()) and later as module_init() for high-level drivers).

Checks for media type, ->driver_req, etc.  are moved from the
ide_scan_devices() to ->reinit().  ide_scan_devices() had lost first two
arguments (it will completely disappear later).

This puts drives on cyclic lists - per-driver ones for drives that had
been claimed by high-level drivers and ata_unused for unclaimed drives.
We put drives on ata_unused in the very end of ideprobe_init() and then
move them to drivers' lists as they are claimed.

Finish introduction of ->reinit() - Jens had missed MOD_DEC_USE_COUNT on
several exits from ide-cd one and forgot to remove the loop from
ide-floppy ide-tape and ide-scsi ones ;-) (->reinit() is the body of
loop in ->init() - stuff that should be done one drive; in 2.5.32
ide-disk one is OK, ide-cd is OK modulo minor bugs and in the rest it's
a copy of ->init())

Move stuff from ide_register_subdriver() (associating drive with
high-level driver) to ide-probe.c, so that remaining stuff can be safely
called in parallel with IO on other drives [Andre]

This adds list_for_each_entry, which is the equivalent of list_for_each
and list_entry, except only one variable is needed.

Just pushes the BKL down a little, no big deal.

This optimisation is really noticeable as it avoids having to take the
BKL on every close().

 - remove elf_caddr_t. It's positively dangerous to #define this since
   elf_caddr_t foo, bar; creates variables of different types (foo is
   char *, bar is char).
 - rewrite large chunks of create_elf_tables(), it needed cleaning anyway.
 - add upwards-growing stack support to create_elf_tables.
 - redefine the ARCH_DLINFO stuff on powerpc -- it's tested, works.
 - add upwards-growing-stack support to exec.c too.

into home.transmeta.com:/home/torvalds/v2.5/linux

and one USB net driver:  3c574_cs, ibmtr_cs, pcnet_cs, ray_cs,
xirc2ps_cs, xircom_cb, and usb/net/kaweth

return EOPNOTSUPP if no eeprom present, in ETHTOOL_SEEPROM ioctl

(thanks for DaveM for advice and help)

* fix tx checksumming (it's still ifdef'd out by default)
* bump version to 0.2.0
* ifdef out dev->change_mtu support, it is reported broken.

o Feature: Merged NAPI support from Robert Olsson

o Bug fix: moved tx_timeout processing from interrupt context 
  to process context so h/w controller reset can busy-wait.

o Bug fix: ethtool SSET and NWAY we're broken when !netif_running.
o Cleanup: removed PPC code optimization - not needed.
o Bug fix: workaround for Dell Avalon system: change descriptor
  write-back policy to write back 16 bytes rather than 8 bytes.
o Bug fix: added mwb() to force memory transaction ordering on ia-64.
o Cleanup: misc. whitespace cleanup.

o Feature: added new interrupt mitigation knobs.

o Change license from Dual BSD/GPL to GPL

o Forward port of changes from 2.4.20-pre4:
   o ethtool security fixes from Alan Cox
   o usec_delay to udelay (Jeff Garzik)
   o #include <linux/sched.h> for Alpha (Jeff Garzik)

into mandrakesoft.com:/home/jgarzik/repo/net-drivers-2.5

o Bug fix: ethernet bridging not working
o Bug fix: mii-diag does not update driver's speed, 
  duplex, and flow control
o Bug fix: ethtool shows wrong speed/duplex when not connected
o Bug fix: ethtool shows wrong speed/duplex when reconnected if
  forced speed/duplex
o Bug fix: ethtool PHY loopback diagnostic fails

(yay!)
o Changed license from Dual BSD/GPL to GPL

o Feature: added e100 GREGS register dump for ethtool
o Bug fix: promiscuous mode was broken
o Bug fix: register ethx as name when requesting interrupt.
o Bug fix: ARP WOL fails

o Cleanup: sync with driver in 2.4.20-pre4.  includes small cleanups,
  and a security fix.

  Here's the bt819 i2c-old --> i2c patch.

 Here's the saa7110.c i2c-old --> i2c patch.

  Another i2c-old --> i2c patch for bt856.c .

Instead of checking for cetain architectures in the Makefile set
CONFIG_HW_CONSOLE in Config.in if we support a hardware console.