- 16 Jul, 2015 14 commits
-
-
Vineet Gupta authored
commit d57f7272 upstream. When auditing cmpxchg call sites, Chuck noted that gcc was optimizing away some of the desired LDs. | do { | new = old = *ipi_data_ptr; | new |= 1U << msg; | } while (cmpxchg(ipi_data_ptr, old, new) != old); was generating to below | 8015cef8: ld r2,[r4,0] <-- First LD | 8015cefc: bset r1,r2,r1 | | 8015cf00: llock r3,[r4] <-- atomic op | 8015cf04: brne r3,r2,8015cf10 | 8015cf08: scond r1,[r4] | 8015cf0c: bnz 8015cf00 | | 8015cf10: brne r3,r2,8015cf00 <-- Branch doesn't go to orig LD Although this was fixed by adding a ACCESS_ONCE in this call site, it seems safer (for now at least) to add compiler barrier to LLSC based cmpxchg Reported-by:
Chuck Jordan <cjordan@synopsys,com> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Stefan Agner authored
commit 119434f4 upstream. When entering suspend while an wakeup alarm is set, enable_set_wake should make sure that the RTC interrupt keep being enabled and the .irq_set_wake for the RTC interrupt get called. However, since the driver uses the suspend_noirq callback, the call to enable_irq_wake has been made after disabling the interrupts. While .irq_set_wake has been called properly, the interrupt remained disabled. Use the suspend callback to call enable_irq_wake early enough to ensure the RTC interrupt remains enabled. Fixes: 7654e9d4 ("drivers/rtc/rtc-snvs: fix suspend/resume") Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Takashi Iwai authored
commit fff3b16d upstream. Many harddisks (mostly WD ones) have firmware problems and take too long, more than 10 seconds, to resume from suspend. And this often exceeds the default DPM watchdog timeout (12 seconds), resulting in a kernel panic out of sudden. Since most distros just take the default as is, we should give a bit more safer value. This patch increases the default value from 12 seconds to one minute, which has been confirmed to be long enough for such problematic disks. Link: https://bugzilla.kernel.org/show_bug.cgi?id=91921 Fixes: 70fea60d (PM / Sleep: Detect device suspend/resume lockup and log event) Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dan Carpenter authored
commit 7bc10388 upstream. There is a small memory leak on error. Fixes: 0f1b414d (ACPI / PNP: Avoid conflicting resource reservations) Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Alexey Brodkin authored
commit f1590670 upstream. Current implementation of descriptor init procedure only takes care about setting/clearing ownership flag in "des0"/"des1" fields while it is perfectly possible to get unexpected bits set because of the following factors: [1] On driver probe underlying memory allocated with dma_alloc_coherent() might not be zeroed and so it will be filled with garbage. [2] During driver operation some bits could be set by SD/MMC controller (for example error flags etc). And unexpected and/or randomly set flags in "des0"/"des1" fields may lead to unpredictable behavior of GMAC DMA block. This change addresses both items above with: [1] Use of dma_zalloc_coherent() instead of simple dma_alloc_coherent() to make sure allocated memory is zeroed. That shouldn't affect performance because this allocation only happens once on driver probe. [2] Do explicit zeroing of both "des0" and "des1" fields of all buffer descriptors during initialization of DMA transfer. And while at it fixed identation of dma_free_coherent() counterpart as well. Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: arc-linux-dev@synopsys.com Cc: linux-kernel@vger.kernel.org Cc: David Miller <davem@davemloft.net> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jan Kara authored
commit 2426f391 upstream. file_remove_suid() could mistakenly set S_NOSEC inode bit when root was modifying the file. As a result following writes to the file by ordinary user would avoid clearing suid or sgid bits. Fix the bug by checking actual mode bits before setting S_NOSEC. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Jingoo Han authored
commit 294240ff upstream. When kzalloc() is called under spin_lock(), GFP_ATOMIC should be used to avoid sleeping allocation. The call tree is: of_pci_range_to_resource() --> pci_register_io_range() <-- takes spin_lock(&io_range_lock); --> kzalloc() Signed-off-by:
Jingoo Han <jingoohan1@gmail.com> Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Eric W. Biederman authored
commit 8405a8ff upstream. Add code to nf_unregister_hook to flush the nf_queue when a hook is unregistered. This guarantees that the pointer that the nf_queue code retains into the nf_hook list will remain valid while a packet is queued. I tested what would happen if we do not flush queued packets and was trivially able to obtain the oops below. All that was required was to stop the nf_queue listening process, to delete all of the nf_tables, and to awaken the nf_queue listening process. > BUG: unable to handle kernel paging request at 0000000100000001 > IP: [<0000000100000001>] 0x100000001 > PGD b9c35067 PUD 0 > Oops: 0010 [#1] SMP > Modules linked in: > CPU: 0 PID: 519 Comm: lt-nfqnl_test Not tainted > task: ffff8800b9c8c050 ti: ffff8800ba9d8000 task.ti: ffff8800ba9d8000 > RIP: 0010:[<0000000100000001>] [<0000000100000001>] 0x100000001 > RSP: 0018:ffff8800ba9dba40 EFLAGS: 00010a16 > RAX: ffff8800bab48a00 RBX: ffff8800ba9dba90 RCX: ffff8800ba9dba90 > RDX: ffff8800b9c10128 RSI: ffff8800ba940900 RDI: ffff8800bab48a00 > RBP: ffff8800b9c10128 R08: ffffffff82976660 R09: ffff8800ba9dbb28 > R10: dead000000100100 R11: dead000000200200 R12: ffff8800ba940900 > R13: ffffffff8313fd50 R14: ffff8800b9c95200 R15: 0000000000000000 > FS: 00007fb91fc34700(0000) GS:ffff8800bfa00000(0000) knlGS:0000000000000000 > CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > CR2: 0000000100000001 CR3: 00000000babfb000 CR4: 00000000000007f0 > Stack: > ffffffff8206ab0f ffffffff82982240 ffff8800bab48a00 ffff8800b9c100a8 > ffff8800b9c10100 0000000000000001 ffff8800ba940900 ffff8800b9c10128 > ffffffff8206bd65 ffff8800bfb0d5e0 ffff8800bab48a00 0000000000014dc0 > Call Trace: > [<ffffffff8206ab0f>] ? nf_iterate+0x4f/0xa0 > [<ffffffff8206bd65>] ? nf_reinject+0x125/0x190 > [<ffffffff8206dee5>] ? nfqnl_recv_verdict+0x255/0x360 > [<ffffffff81386290>] ? nla_parse+0x80/0xf0 > [<ffffffff8206c42c>] ? nfnetlink_rcv_msg+0x13c/0x240 > [<ffffffff811b2fec>] ? __memcg_kmem_get_cache+0x4c/0x150 > [<ffffffff8206c2f0>] ? nfnl_lock+0x20/0x20 > [<ffffffff82068159>] ? netlink_rcv_skb+0xa9/0xc0 > [<ffffffff820677bf>] ? netlink_unicast+0x12f/0x1c0 > [<ffffffff82067ade>] ? netlink_sendmsg+0x28e/0x650 > [<ffffffff81fdd814>] ? sock_sendmsg+0x44/0x50 > [<ffffffff81fde07b>] ? ___sys_sendmsg+0x2ab/0x2c0 > [<ffffffff810e8f73>] ? __wake_up+0x43/0x70 > [<ffffffff8141a134>] ? tty_write+0x1c4/0x2a0 > [<ffffffff81fde9f4>] ? __sys_sendmsg+0x44/0x80 > [<ffffffff823ff8d7>] ? system_call_fastpath+0x12/0x6a > Code: Bad RIP value. > RIP [<0000000100000001>] 0x100000001 > RSP <ffff8800ba9dba40> > CR2: 0000000100000001 > ---[ end trace 08eb65d42362793f ]--- Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Ralf Baechle authored
commit d496f784 upstream. A ROSE socket doesn't necessarily always have a neighbour pointer so check if the neighbour pointer is valid before dereferencing it. Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Tested-by:
Bernard Pidoux <f6bvp@free.fr> Signed-off-by:
-
Dave Airlie authored
commit 9eb1e57f upstream. If we are doing an MST transaction and we've gotten HPD and we lookup the device from the incoming msg, we should take the mgr lock around it, so that mst_primary and mstb->ports are valid. Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Daniel Vetter authored
commit 9254ec49 upstream. This validates the mst_primary under the lock, and then calls into the check and send function. This makes the code a lot easier to understand the locking rules in. Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Reviewed-by:
-
Darrick J. Wong authored
commit 292db1bc upstream. ext4 isn't willing to map clusters to a non-extent file. Don't signal this with an out of space error, since the FS will retry the allocation (which didn't fail) forever. Instead, return EUCLEAN so that the operation will fail immediately all the way back to userspace. (The fix is either to run e2fsck -E bmap2extent, or to chattr +e the file.) Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Eric Sandeen authored
commit 2ac56d3d upstream. If we create a CRC filesystem, mount it, and create a symlink with a path long enough that it can't live in the inode, we get a very strange result upon remount: # ls -l mnt total 4 lrwxrwxrwx. 1 root root 929 Jun 15 16:58 link -> XSLM XSLM is the V5 symlink block header magic (which happens to be followed by a NUL, so the string looks terminated). xfs_readlink_bmap() advanced cur_chunk by the size of the header for CRC filesystems, but never actually used that pointer; it kept reading from bp->b_addr, which is the start of the block, rather than the start of the symlink data after the header. Looks like this problem goes back to v3.10. Fixing this gets us reading the proper link target, again. Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Reviewed-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
James Hogan authored
commit 8e748c8d upstream. KVM guest kernels for trap & emulate run in user mode, with a modified set of kernel memory segments. However the fixmap address is still in the normal KSeg3 region at 0xfffe0000 regardless, causing problems when cache alias handling makes use of them when handling copy on write. Therefore define FIXADDR_TOP as 0x7ffe0000 in the guest kernel mapped region when CONFIG_KVM_GUEST is defined. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/9887/Signed-off-by:
-
- 15 Jul, 2015 26 commits
-
-
Theodore Ts'o authored
commit 89d96a6f upstream. Normally all of the buffers will have been forced out to disk before we call invalidate_bdev(), but there will be some cases, where a file system operation was aborted due to an ext4_error(), where there may still be some dirty buffers in the buffer cache for the device. So try to force them out to memory before calling invalidate_bdev(). This fixes a warning triggered by generic/081: WARNING: CPU: 1 PID: 3473 at /usr/projects/linux/ext4/fs/block_dev.c:56 __blkdev_put+0xb5/0x16f() Signed-off-by:
-
Joerg Roedel authored
commit 0b3fff54 upstream. Make sure that we are skipping over large PTEs while walking the page-table tree. Fixes: 5c34c403 ("iommu/amd: Fix memory leak in free_pagetable") Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Will Deacon authored
commit 6f1a6ae8 upstream. When building the kernel with a bare-metal (ELF) toolchain, the -shared option may not be passed down to collect2, resulting in silent corruption of the vDSO image (in particular, the DYNAMIC section is omitted). The effect of this corruption is that the dynamic linker fails to find the vDSO symbols and libc is instead used for the syscalls that we intended to optimise (e.g. gettimeofday). Functionally, there is no issue as the sigreturn trampoline is still intact and located by the kernel. This patch fixes the problem by explicitly passing -shared to the linker when building the vDSO. Reported-by:
Szabolcs Nagy <Szabolcs.Nagy@arm.com> Reported-by:
James Greenlaigh <james.greenhalgh@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Martin K. Petersen authored
commit 243918be upstream. Queued TRIM got disabled on Micron M500DC drives thanks to the "Micron_M500*" pattern we had in place to accommodate the previous generation of this drive family. Tweak the blacklist entry slightly so we only disable queued TRIM for the non-DC variants of M500 drives. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Dmitry Tunin authored
commit 7e730c7f upstream. BugLink: https://bugs.launchpad.net/bugs/1394368 This device requires new firmware files AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to /lib/firmware/ar3k/ that are not included in linux-firmware yet. T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=300d Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Dmitry Tunin authored
commit ec0810d2 upstream. BugLink: https://bugs.launchpad.net/bugs/1449730 T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=300f Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
-
Rafael J. Wysocki authored
commit 0f1b414d upstream. Commit b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()" overlooked the fact that the memory and/or I/O regions reserved by acpi_reserve_resources() may conflict with those reserved by the PNP "system" driver. If that conflict actually takes place, it causes the reservations made by the "system" driver to fail while before commit b9a5e5e1 all reservations made by it and by acpi_reserve_resources() would be successful. In turn, that allows the resources that haven't been reserved by the "system" driver to be used by others (e.g. PCI) which sometimes leads to functional problems (up to and including boot failures). To fix that issue, introduce a common resource reservation routine, acpi_reserve_region(), to be used by both acpi_reserve_resources() and the "system" driver, that will track all resources reserved by it and avoid making conflicting requests. Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831 Link: http://marc.info/?t=143389402600001&r=1&w=2 Fixes: b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()" Reported-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
-
Trond Myklebust authored
commit c7070113 upstream. If a write attempt fails, and the write is queued up for resending to the server, as opposed to being dropped, then we need to set the appropriate flag so that nfs_file_fsync() does the right thing. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Trond Myklebust authored
commit 1ca018d2 upstream. pnfs_do_write() expects the call to pnfs_write_through_mds() to free the pgio header and to release the layout segment before exiting. The problem is that nfs_pgio_data_destroy() doesn't actually do this; it only frees the memory allocated by nfs_generic_pgio(). Ditto for pnfs_do_read()... Fix in both cases is to add a call to hdr->release(hdr). Signed-off-by:
-
Bjorn Helgaas authored
commit 3d9fecf6 upstream. We enable _CRS on all systems from 2008 and later. On older systems, we ignore _CRS and assume the whole physical address space (excluding RAM and other devices) is available for PCI devices, but on systems that support physical address spaces larger than 4GB, it's doubtful that the area above 4GB is really available for PCI. After d56dbf5b ("PCI: Allocate 64-bit BARs above 4G when possible"), we try to use that space above 4GB *first*, so we're more likely to put a device there. On Juan's Toshiba Satellite Pro U200, BIOS left the graphics, sound, 1394, and card reader devices unassigned (but only after Windows had been booted). Only the sound device had a 64-bit BAR, so it was the only device placed above 4GB, and hence the only device that didn't work. Keep _CRS enabled even on pre-2008 systems if they support physical address space larger than 4GB. Fixes: d56dbf5b ("PCI: Allocate 64-bit BARs above 4G when possible") Reported-and-tested-by:
Juan Dayer <jdayer@outlook.com> Reported-and-tested-by:
Alan Horsfield <alan@hazelgarth.co.uk> Link: https://bugzilla.kernel.org/show_bug.cgi?id=99221 Link: https://bugzilla.opensuse.org/show_bug.cgi?id=907092Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Mikulas Patocka authored
commit dd4c1b7d upstream. If the number_of_areas argument was zero the kernel would crash on div-by-zero. Add better input validation. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Thomas Petazzoni authored
commit 2f5bc307 upstream. The current Armada XP suspend to RAM implementation, as added in commit 27432825 ("ARM: mvebu: Armada XP GP specific suspend/resume code") does not handle big-endian configurations properly: the small bit of assembly code putting the DRAM in self-refresh and toggling the GPIOs to turn off power forgets to convert the values to little-endian. This commit fixes that by making sure the two values we will write to the DRAM controller register and GPIO register are already in little-endian before entering the critical assembly code. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Fixes: 27432825 ("ARM: mvebu: Armada XP GP specific suspend/resume code") Signed-off-by:
-
Marc Zyngier authored
commit 4839ddc2 upstream. Commit fd1d0ddf (KVM: arm/arm64: check IRQ number on userland injection) rightly limited the range of interrupts userspace can inject in a guest, but failed to consider the (unlikely) case where a guest is configured with 1024 interrupts. In this case, interrupts ranging from 1020 to 1023 are unuseable, as they have a special meaning for the GIC CPU interface. Make sure that these number cannot be used as an IRQ. Also delete a redundant (and similarily buggy) check in kvm_set_irq. Reported-by:
Peter Maydell <peter.maydell@linaro.org> Cc: Andre Przywara <andre.przywara@arm.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> [ kamal: backport to 3.19-stable: no change to kvm_set_irq ] Signed-off-by:
-
Joe Thornber authored
commit 6096d91a upstream. The metadata space map has a simplified 'bootstrap' mode that is operational when extending the space maps. Whilst in this mode it's possible for some refcount decrement operations to become queued (eg, as a result of shadowing one of the bitmap indexes). These decrements were not being applied when switching out of bootstrap mode. The effect of this bug was the leaking of a 4k metadata block. This is detected by the latest version of thin_check as a non fatal error. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Dave P Martin authored
commit b9bcc919 upstream. The memmap freeing code in free_unused_memmap() computes the end of each memblock by adding the memblock size onto the base. However, if SPARSEMEM is enabled then the value (start) used for the base may already have been rounded downwards to work out which memmap entries to free after the previous memblock. This may cause memmap entries that are in use to get freed. In general, you're not likely to hit this problem unless there are at least 2 memblocks and one of them is not aligned to a sparsemem section boundary. Note that carve-outs can increase the number of memblocks by splitting the regions listed in the device tree. This problem doesn't occur with SPARSEMEM_VMEMMAP, because the vmemmap code deals with freeing the unused regions of the memmap instead of requiring the arch code to do it. This patch gets the memblock base out of the memblock directly when computing the block end address to ensure the correct value is used. Signed-off-by:
Dave Martin <Dave.Martin@arm.com> Signed-off-by:
-
Alexander Sverdlin authored
commit 0a8237ae upstream. pca9541 and pca954x are calling master_xfer() of the parent adapter directly thus bypassing the quirks checks of the adapter. Use __i2c_transfer() instead. Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> Tested-by:
Łukasz Gemborowski <lukasz.gemborowski@nokia.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Fixes: b7f62584 ("i2c: add quirk checks to core") Signed-off-by:
-
Alexander Sverdlin authored
commit e766f338 upstream. Newly introduced quirks infrastructure doesn't work for the devices behind MUXes because MUX's master_xfer() calls parent's master_xfer() directly without checking the quirks. Instead of duplicating check code in MUX just call __i2c_transfer() instead. This has a side effect on tracing (messages will appear on both MUX bus and parent bus), but maybe that's not bad at the end. Signed-off-by:
-
Mark Rutland authored
commit 46b0567c upstream. Commit 6c81fe79 ("arm64: enable context tracking") did not update el0_sp_pc to use ct_user_exit, but this appears to have been unintentional. In commit 6ab6463a ("arm64: adjust el0_sync so that a function can be called") we made x0 available, and in the return to userspace we call ct_user_enter in the kernel_exit macro. Due to this, we currently don't correctly inform RCU of the user->kernel transition, and may erroneously account for time spent in the kernel as if we were in an extended quiescent state when CONFIG_CONTEXT_TRACKING is enabled. As we do record the kernel->user transition, a userspace application making accesses from an unaligned stack pointer can demonstrate the imbalance, provoking the following warning: ------------[ cut here ]------------ WARNING: CPU: 2 PID: 3660 at kernel/context_tracking.c:75 context_tracking_enter+0xd8/0xe4() Modules linked in: CPU: 2 PID: 3660 Comm: a.out Not tainted 4.1.0-rc7+ #8 Hardware name: ARM Juno development board (r0) (DT) Call trace: [<ffffffc000089914>] dump_backtrace+0x0/0x124 [<ffffffc000089a48>] show_stack+0x10/0x1c [<ffffffc0005b3cbc>] dump_stack+0x84/0xc8 [<ffffffc0000b3214>] warn_slowpath_common+0x98/0xd0 [<ffffffc0000b330c>] warn_slowpath_null+0x14/0x20 [<ffffffc00013ada4>] context_tracking_enter+0xd4/0xe4 [<ffffffc0005b534c>] preempt_schedule_irq+0xd4/0x114 [<ffffffc00008561c>] el1_preempt+0x4/0x28 [<ffffffc0001b8040>] exit_files+0x38/0x4c [<ffffffc0000b5b94>] do_exit+0x430/0x978 [<ffffffc0000b614c>] do_group_exit+0x40/0xd4 [<ffffffc0000c0208>] get_signal+0x23c/0x4f4 [<ffffffc0000890b4>] do_signal+0x1ac/0x518 [<ffffffc000089650>] do_notify_resume+0x5c/0x68 ---[ end trace 963c192600337066 ]--- This patch adds the missing ct_user_exit to the el0_sp_pc entry path, correcting the context tracking for this case. Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Acked-by:
-
Lorenzo Pieralisi authored
commit e2d99736 upstream. According to the PSCI specification and the SMC/HVC calling convention, PSCI function_ids that are not implemented must return NOT_SUPPORTED as return value. Current KVM implementation takes an unhandled PSCI function_id as an error and injects an undefined instruction into the guest if PSCI implementation is called with a function_id that is not handled by the resident PSCI version (ie it is not implemented), which is not the behaviour expected by a guest when calling a PSCI function_id that is not implemented. This patch fixes this issue by returning NOT_SUPPORTED whenever the kvm PSCI call is executed for a function_id that is not implemented by the PSCI kvm layer. Cc: Christoffer Dall <christoffer.dall@linaro.org> Acked-by:
Sudeep Holla <sudeep.holla@arm.com> Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by:
-
Marc Zyngier authored
commit 85e84ba3 upstream. On VM entry, we disable access to the VFP registers in order to perform a lazy save/restore of these registers. On VM exit, we restore access, test if we did enable them before, and save/restore the guest/host registers if necessary. In this sequence, the FPEXC register is always accessed, irrespective of the trapping configuration. If the guest didn't touch the VFP registers, then the HCPTR access has now enabled such access, but we're missing a barrier to ensure architectural execution of the new HCPTR configuration. If the HCPTR access has been delayed/reordered, the subsequent access to FPEXC will cause a trap, which we aren't prepared to handle at all. The same condition exists when trapping to enable VFP for the guest. The fix is to introduce a barrier after enabling VFP access. In the vmexit case, it can be relaxed to only takes place if the guest hasn't accessed its view of the VFP registers, making the access to FPEXC safe. The set_hcptr macro is modified to deal with both vmenter/vmexit and vmtrap operations, and now takes an optional label that is branched to when the guest hasn't touched the VFP registers. Reported-by:
Vikram Sethi <vikrams@codeaurora.org> Signed-off-by:
-
Frodo Lai authored
commit 469d7d22 upstream. The i2c_master_recv() uses readsize to receive data from i2c but compares to size of rdbuf which is always 27. This would cause problem when the max_fingers is not 5. Change the comparison value to readsize instead. Fixes: 36874c7e ("Input: pixcir_i2c_ts - support up to 5 fingers and hardware tracking IDs:) Signed-off-by:
Frodo Lai <frodo_lai@bcmcom.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Hon Ching \\(Vicky\\) Lo authored
commit 9d75f089 upstream. tpm_ibmvtpm_probe() calls ibmvtpm_reset_crq(ibmvtpm) without having yet set the virtual device in the ibmvtpm structure. So in ibmvtpm_reset_crq, the phype call contains empty unit addresses, ibmvtpm->vdev->unit_address. Signed-off-by:
Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com> Signed-off-by:
Joy Latten <jmlatten@linux.vnet.ibm.com> Reviewed-by:
Ashley Lai <ashley@ahsleylai.com> Fixes: 132f7629 ("drivers/char/tpm: Add new device driver to support IBM vTPM") Signed-off-by:
Peter Huewe <peterhuewe@gmx.de> Signed-off-by:
-
Jeff Layton authored
commit 764ad8ba upstream. The current buffer is much too small if you have a relatively long hostname. Bring it up to the size of the one that SETCLIENTID has. Reported-by:
Michael Skralivetsky <michael.skralivetsky@primarydata.com> Signed-off-by:
Jeff Layton <jeff.layton@primarydata.com> Signed-off-by:
-
Mimi Zohar authored
commit 4351c294 upstream. The current "mask" policy option matches files opened as MAY_READ, MAY_WRITE, MAY_APPEND or MAY_EXEC. This patch extends the "mask" option to match files opened containing one of these modes. For example, "mask=^MAY_READ" would match files opened read-write. Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
Dr. Greg Wettstein <gw@idfusion.org> Signed-off-by:
-
Mimi Zohar authored
commit 139069ef upstream. The new "euid" policy condition measures files with the specified effective uid (euid). In addition, for CAP_SETUID files it measures files with the specified uid or suid. Changelog: - fixed checkpatch.pl warnings - fixed avc denied {setuid} messages - based on Roberto's feedback Signed-off-by:
-
Mimi Zohar authored
commit 45b26133 upstream. This patch fixes a bug introduced in "4d7aeee ima: define new template ima-ng and template fields d-ng and n-ng". Changelog: - change int to uint32 (Roberto Sassu's suggestion) Signed-off-by:
Roberto Sassu <rsassu@suse.de> Signed-off-by:
-
