- 30 Mar, 2017 39 commits
-
-
Johan Hovold authored
commit 1dc56c52 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should the probed device lack endpoints. Note that this driver does not bind to any devices by default. Fixes: ce21bfe6 ("USB: Add LVS Test device driver") Cc: Pratyush Anand <pratyush.anand@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
commit f259ca3e upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Note that the endpoint access that causes the NULL-deref is currently only used for debugging purposes during probe so the oops only happens when dynamic debugging is enabled. This means the driver could be rewritten to continue to accept device with only two endpoints, should such devices exist. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Samuel Thibault authored
commit 3243367b upstream. Some USB 2.0 devices erroneously report millisecond values in bInterval. The generic config code manages to catch most of them, but in some cases it's not completely enough. The case at stake here is a USB 2.0 braille device, which wants to announce 10ms and thus sets bInterval to 10, but with the USB 2.0 computation that yields to 64ms. It happens that one can type fast enough to reach this interval and get the device buffers overflown, leading to problematic latencies. The generic config code does not catch this case because the 64ms is considered a sane enough value. This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk to mark devices which actually report milliseconds in bInterval, and marks Vario Ultra devices as needing it. Signed-off-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Roger Quadros authored
commit 09424c50 upstream. The streaming_maxburst module parameter is 0 offset (0..15) so we must add 1 while using it for wBytesPerInterval calculation for the SuperSpeed companion descriptor. Without this host uvcvideo driver will always see the wrong wBytesPerInterval for SuperSpeed uvc gadget and may not find a suitable video interface endpoint. e.g. for streaming_maxburst = 0 case it will always fail as wBytePerInterval was evaluating to 0. Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Oliver Neukum authored
commit cdd7928d upstream. The gadget code exports the bitfield for serial status changes over the wire in its internal endianness. The fix is to convert to little endian before sending it over the wire. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Tested-by:
家瑋 <momo1208@gmail.com> Signed-off-by:
-
Bjørn Mork authored
commit 436ecf55 upstream. This is a Dell branded Sierra Wireless EM7455. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Dan Williams authored
commit 6e9f44ea upstream. Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by qcserial due to a USB VID/PID conflict with an existing Acer device. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Hui Wang authored
commit 3f307834 upstream. A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to fix the headset problem, and the pin definiton of this machine is not in the pin quirk table yet, now adding it to the table. Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit f363a066 upstream. In the commit [15c75b09: ALSA: ctxfi: Fallback DMA mask to 32bit], I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while cthw20k2.c is OK). This patch fixes that obvious bug. (As a side note: although the original commit was completely wrong, it's still working for most of machines, as it sets to 32bit DMA mask in the end. So the bug severity is low.) Fixes: 15c75b09 ("ALSA: ctxfi: Fallback DMA mask to 32bit") Signed-off-by:
-
Takashi Iwai authored
commit c520ff3d upstream. When snd_seq_pool_done() is called, it marks the closing flag to refuse the further cell insertions. But snd_seq_pool_done() itself doesn't clear the cells but just waits until all cells are cleared by the caller side. That is, it's racy, and this leads to the endless stall as syzkaller spotted. This patch addresses the racy by splitting the setup of pool->closing flag out of snd_seq_pool_done(), and calling it properly before snd_seq_pool_done(). BugLink: http://lkml.kernel.org/r/CACT4Y+aqqy8bZA1fFieifNxR2fAfFQQABcBHj801+u5ePV0URw@mail.gmail.comReported-and-tested-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Johan Hovold authored
commit 92461f5d upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory that lie beyond the end of the endpoint array should a malicious device lack the expected endpoints. Fixes: bdb5c57f ("Input: add sur40 driver for Samsung SUR40... ") Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit cb1b4946 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Signed-off-by:
-
Johan Hovold authored
commit ac2ee9ba upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: c04148f9 ("Input: add driver for USB VoIP phones with CM109...") Signed-off-by:
-
Johan Hovold authored
commit 5cc4a1a9 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: aca951a2 ("[PATCH] input-driver-yealink-P1K-usb-phone") Signed-off-by:
-
Johan Hovold authored
commit ba340d7b upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: bba5394a ("Input: add support for Hanwang tablets") Signed-off-by:
-
Johan Hovold authored
commit 1916d319 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack control-interface endpoints. Fixes: 628329d5 ("Input: add IMS Passenger Control Unit driver") Signed-off-by:
-
Johan Hovold authored
commit 59cf8bed upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory that lie beyond the end of the endpoint array should a malicious device lack the expected endpoints. Signed-off-by:
-
Kai-Heng Feng authored
commit 45838660 upstream. The aux port does not get detected without noloop quirk, so external PS/2 mouse cannot work as result. The PS/2 mouse can work with this quirk. BugLink: https://bugs.launchpad.net/bugs/1591053Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by:
Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by:
-
Matjaz Hegedic authored
commit 92ef6f97 upstream. EeeBook X205TA is yet another ASUS device with a special touchpad firmware that needs to be accounted for during initialization, or else the touchpad will go into an invalid state upon suspend/resume. Adding the appropriate ic_type and product_id check fixes the problem. Signed-off-by:
Matjaz Hegedic <matjaz.hegedic@gmail.com> Acked-by:
KT Liao <kt.liao@emc.com.tw> Signed-off-by:
-
Masaki Ota authored
commit 47e6fb42 upstream. Alps stick devices always have physical buttons, so we should not check ALPS_BUTTONPAD flag to decide whether we should report them. Fixes: 4777ac22 ("Input: ALPS - add touchstick support for SS5 hardware") Signed-off-by:
Masaki Ota <masaki.ota@jp.alps.com> Acked-by:
Pali Rohar <pali.rohar@gmail.com> Tested-by:
Paul Donohue <linux-kernel@PaulSD.com> Tested-by:
Nick Fletcher <nick.m.fletcher@gmail.com> Signed-off-by:
-
Masaki Ota authored
commit e7348396 upstream. Devices identified as E7="73 03 28" use slightly modified version of V8 protocol, with lower count per electrode, different offsets, and different feature bits in OTP data. Fixes: aeaa881f ("Input: ALPS - set DualPoint flag for 74 03 28 devices") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 15bb7745 ] icsk_ack.lrcvtime has a 0 value at socket creation time. tcpi_last_data_recv can have bogus value if no payload is ever received. This patch initializes icsk_ack.lrcvtime for active sessions in tcp_finish_connect(), and for passive sessions in tcp_create_openreq_child() Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit a97e50cc ] In sk_clone_lock(), we create a new socket and inherit most of the parent's members via sock_copy() which memcpy()'s various sections. Now, in case the parent socket had a BPF socket filter attached, then newsk->sk_filter points to the same instance as the original sk->sk_filter. sk_filter_charge() is then called on the newsk->sk_filter to take a reference and should that fail due to hitting max optmem, we bail out and release the newsk instance. The issue is that commit 278571ba ("net: filter: simplify socket charging") wrongly combined the dismantle path with the failure path of xfrm_sk_clone_policy(). This means, even when charging failed, we call sk_free_unlock_clone() on the newsk, which then still points to the same sk_filter as the original sk. Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually where it tests for present sk_filter and calls sk_filter_uncharge() on it, which potentially lets sk_omem_alloc wrap around and releases the eBPF prog and sk_filter structure from the (still intact) parent. Fix it by making sure that when sk_filter_charge() failed, we reset newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(), so that we don't mess with the parents sk_filter. Only if xfrm_sk_clone_policy() fails, we did reach the point where either the parent's filter was NULL and as a result newsk's as well or where we previously had a successful sk_filter_charge(), thus for that case, we do need sk_filter_uncharge() to release the prior taken reference on sk_filter. Fixes: 278571ba ("net: filter: simplify socket charging") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit c64c0b3c ] Alexander reported a KMSAN splat caused by reads of uninitialized field (tb_id_in) from user provided struct fib_result_nl It turns out nl_fib_input() sanity tests on user input is a bit wrong : User can pretend nlh->nlmsg_len is big enough, but provide at sendmsg() time a too small buffer. Reported-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
-
Doug Berger authored
[ Upstream commit 31739eae ] Commit 6ac3ce82 ("net: bcmgenet: Remove excessive PHY reset") removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and bcmgenet_internal_phy_setup() functions. In so doing it broke the reset of the internal PHY devices used by the GENETv1-GENETv3 which required this reset before the UniMAC was enabled. It also broke the internal GPHY devices used by the GENETv4 because the config_init that installed the AFE workaround was no longer occurring after the reset of the GPHY performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup(). In addition the code in bcmgenet_internal_phy_setup() related to the "enable APD" comment goes with the bcmgenet_mii_reset() so it should have also been removed. Commit bd4060a6 ("net: bcmgenet: Power on integrated GPHY in bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the bcmgenet_power_up() function, but failed to remove it from the bcmgenet_internal_phy_setup() function. Had it done so, the bcmgenet_internal_phy_setup() function would have been empty and could have been removed at that time. Commit 5dbebbb4 ("net: bcmgenet: Software reset EPHY after power on") was submitted to correct the functional problems introduced by commit 6ac3ce82 ("net: bcmgenet: Remove excessive PHY reset"). It was included in v4.4 and made available on 4.3-stable. Unfortunately, it didn't fully revert the commit because this bcmgenet_mii_reset() doesn't apply the soft reset to the internal GPHY used by GENETv4 like the previous one did. This prevents the restoration of the AFE work- arounds for internal GPHY devices after the bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup(). This commit takes the alternate approach of removing the unnecessary bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3 so that when bcmgenet_mii_reset() was restored it should have only gone into bcmgenet_power_up(). This will avoid the problems while also removing the redundancy (and hopefully some of the confusion). Fixes: 6ac3ce82 ("net: bcmgenet: Remove excessive PHY reset") Signed-off-by:
Doug Berger <opendmb@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Alexander Potapenko authored
[ Upstream commit d515684d ] In the case udp_sk(sk)->pending is AF_INET6, udpv6_sendmsg() would jump to do_append_data, skipping the initialization of sockc.tsflags. Fix the problem by moving sockc.tsflags initialization earlier. The bug was detected with KMSAN. Fixes: c14ac945 ("sock: enable timestamping using control messages") Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Gal Pressman authored
[ Upstream commit 8ab7e2ae ] RX packets statistics ('rx_packets' counter) used to count LRO packets as one, even though it contains multiple segments. This patch will increment the counter by the number of segments, and align the driver with the behavior of other drivers in the stack. Note that no information is lost in this patch due to 'rx_lro_packets' counter existence. Before, ethtool showed: $ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets" rx_packets: 435277 rx_lro_packets: 35847 rx_packets_phy: 1935066 Now, we will see the more logical statistics: $ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets" rx_packets: 1935066 rx_lro_packets: 35847 rx_packets_phy: 1935066 Fixes: e586b3b0 ("net/mlx5: Ethernet Datapath files") Signed-off-by:
Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Acked-by:
-
Gal Pressman authored
[ Upstream commit d3a4e4da ] TX packets statistics ('tx_packets' counter) used to count GSO packets as one, even though it contains multiple segments. This patch will increment the counter by the number of segments, and align the driver with the behavior of other drivers in the stack. Note that no information is lost in this patch due to 'tx_tso_packets' counter existence. Before, ethtool showed: $ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets" tx_packets: 61340 tx_tso_packets: 60954 tx_packets_phy: 2451115 Now, we will see the more logical statistics: $ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets" tx_packets: 2451115 tx_tso_packets: 60954 tx_packets_phy: 2451115 Fixes: e586b3b0 ("net/mlx5: Ethernet Datapath files") Signed-off-by:
-
Maor Gottlieb authored
[ Upstream commit 5f40b4ed ] With ConnectX-4 sharing SRQs from the same space as QPs, we hit a limit preventing some applications to allocate needed QPs amount. Double the size to 256K. Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit 09c91ddf ] Currently we use the non UAPI values and we miss erring on the modify action which is not supported, fix that. Fixes: 8b32580d ('net/mlx5e: Add TC vlan action for SRIOV offloads') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Reported-by:
Petr Machata <petrm@mellanox.com> Reviewed-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit 1f30a86c ] The switch cases for the rate limit set and query commands were missing, which could get us wrong under fw error or driver reset flow, fix that. Fixes: 1466cc5b ('net/mlx5: Rate limit tables support') Signed-off-by:
Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by:
-
David Ahern authored
[ Upstream commit 3dc857f0 ] The VRF driver takes a reference to the inet6_dev on the VRF device for its rt6_local dst when handling local traffic through the VRF device as a loopback. When the device is deleted the driver does a put on the idev but does not reset rt6i_idev in the rt6_info struct. When the dst is destroyed, dst_destroy calls ip6_dst_destroy which does a second put for what is essentially the same reference causing it to be prematurely freed. Reset rt6i_idev after the put in the vrf driver. Fixes: b4869aa2 ("net: vrf: ipv6 support for local traffic to local addresses") Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit 6bd845d1 ] This is a Dell branded Sierra Wireless EM7455. It is operating in MBIM mode by default, but can be configured to provide two QMI/RMNET functions. Signed-off-by:
-
Andrey Ulanov authored
[ Upstream commit 7df9c246 ] Dmitry has reported that a BUG_ON() condition in unix_notinflight() may be triggered by a simple code that forwards unix socket in an SCM_RIGHTS message. That is caused by incorrect unix socket GC implementation in unix_gc(). The GC first collects list of candidates, then (a) decrements their "children's" inflight counter, (b) checks which inflight counters are now 0, and then (c) increments all inflight counters back. (a) and (c) are done by calling scan_children() with inc_inflight or dec_inflight as the second argument. Commit 6209344f ("net: unix: fix inflight counting bug in garbage collector") changed scan_children() such that it no longer considers sockets that do not have UNIX_GC_CANDIDATE flag. It also added a block of code that that unsets this flag _before_ invoking scan_children(, dec_iflight, ). This may lead to incorrect inflight counters for some sockets. This change fixes this bug by changing order of operations: UNIX_GC_CANDIDATE is now unset only after all inflight counters are restored to the original state. kernel BUG at net/unix/garbage.c:149! RIP: 0010:[<ffffffff8717ebf4>] [<ffffffff8717ebf4>] unix_notinflight+0x3b4/0x490 net/unix/garbage.c:149 Call Trace: [<ffffffff8716cfbf>] unix_detach_fds.isra.19+0xff/0x170 net/unix/af_unix.c:1487 [<ffffffff8716f6a9>] unix_destruct_scm+0xf9/0x210 net/unix/af_unix.c:1496 [<ffffffff86a90a01>] skb_release_head_state+0x101/0x200 net/core/skbuff.c:655 [<ffffffff86a9808a>] skb_release_all+0x1a/0x60 net/core/skbuff.c:668 [<ffffffff86a980ea>] __kfree_skb+0x1a/0x30 net/core/skbuff.c:684 [<ffffffff86a98284>] kfree_skb+0x184/0x570 net/core/skbuff.c:705 [<ffffffff871789d5>] unix_release_sock+0x5b5/0xbd0 net/unix/af_unix.c:559 [<ffffffff87179039>] unix_release+0x49/0x90 net/unix/af_unix.c:836 [<ffffffff86a694b2>] sock_release+0x92/0x1f0 net/socket.c:570 [<ffffffff86a6962b>] sock_close+0x1b/0x20 net/socket.c:1017 [<ffffffff81a76b8e>] __fput+0x34e/0x910 fs/file_table.c:208 [<ffffffff81a771da>] ____fput+0x1a/0x20 fs/file_table.c:244 [<ffffffff81483ab0>] task_work_run+0x1a0/0x280 kernel/task_work.c:116 [< inline >] exit_task_work include/linux/task_work.h:21 [<ffffffff8141287a>] do_exit+0x183a/0x2640 kernel/exit.c:828 [<ffffffff8141383e>] do_group_exit+0x14e/0x420 kernel/exit.c:931 [<ffffffff814429d3>] get_signal+0x663/0x1880 kernel/signal.c:2307 [<ffffffff81239b45>] do_signal+0xc5/0x2190 arch/x86/kernel/signal.c:807 [<ffffffff8100666a>] exit_to_usermode_loop+0x1ea/0x2d0 arch/x86/entry/common.c:156 [< inline >] prepare_exit_to_usermode arch/x86/entry/common.c:190 [<ffffffff81009693>] syscall_return_slowpath+0x4d3/0x570 arch/x86/entry/common.c:259 [<ffffffff881478e6>] entry_SYSCALL_64_fastpath+0xc4/0xc6 Link: https://lkml.org/lkml/2017/3/6/252Signed-off-by:
Andrey Ulanov <andreyu@google.com> Reported-by:
-
Kris Murphy authored
[ Upstream commit 8f3dbfd7 ] Added a case for OVS_TUNNEL_KEY_ATTR_PAD to the switch statement in ip_tun_from_nlattr in order to prevent the default case returning an error. Fixes: b46f6ded ("libnl: nla_put_be64(): align on a 64-bit area") Signed-off-by:
Kris Murphy <kriskend@linux.vnet.ibm.com> Acked-by:
Joe Stringer <joe@ovn.org> Signed-off-by:
-
Lendacky, Thomas authored
[ Upstream commit 622c36f1 ] Newer hardware does not provide a cumulative payload length when multiple descriptors are needed to handle the data. Once the MTU increases beyond the size that can be handled by a single descriptor, the SKB does not get built properly by the driver. The driver will now calculate the size of the data buffers used by the hardware. The first buffer of the first descriptor is for packet headers or packet headers and data when the headers can't be split. Subsequent descriptors in a multi-descriptor chain will not use the first buffer. The second buffer is used by all the descriptors in the chain for payload data. Based on whether the driver is processing the first, intermediate, or last descriptor it can calculate the buffer usage and build the SKB properly. Tested and verified on both old and new hardware. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 22a0e18e ] I mistakenly added the code to release sk->sk_frag in sk_common_release() instead of sk_destruct() TCP sockets using sk->sk_allocation == GFP_ATOMIC do no call sk_common_release() at close time, thus leaking one (order-3) page. iSCSI is using such sockets. Fixes: 5640f768 ("net: use a per task frag allocator") Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 5371bbf4 ] Suspending the PHY would be putting it in a low power state where it may no longer allow us to do Wake-on-LAN. Fixes: cc013fb4 ("net: bcmgenet: correctly suspend and resume PHY device") Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit 3d20f1f7 ] When dealing with ipv6 source tunnel key address attribute (OVS_TUNNEL_KEY_ATTR_IPV6_SRC) we are wrongly setting the tunnel dst ip, fix that. Fixes: 6b26ba3a ('openvswitch: netlink attributes for IPv6 tunneling') Signed-off-by:
Paul Blakey <paulb@mellanox.com> Acked-by:
Jiri Benc <jbenc@redhat.com> Acked-by:
-
- 26 Mar, 2017 1 commit
-
-
Greg Kroah-Hartman authored
-
