An error occurred fetching the project authors.
- 25 Jun, 2019 30 commits
-
-
Douglas Anderson authored
commit 65dade60 upstream. When Broadcom SDIO cards are idled they go to sleep and a whole separate subsystem takes over their SDIO communication. This is the Always-On-Subsystem (AOS) and it can't handle tuning requests. Specifically, as tested on rk3288-veyron-minnie (which reports having BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control() when "on = 1" (aka we're transition from sleep to wake) by whacking: bus->sdiodev->func1->card->host->need_retune = 1 ...then I can often see tuning fail. In this case dw_mmc reports "All phases bad!"). Note that I don't get 100% failure, presumably because sometimes the card itself has already transitioned away from the AOS itself by the time we try to wake it up. If I force retuning when "on = 0" (AKA force retuning right before sending the command to go to sleep) then retuning is always OK. NOTE: we need _both_ this patch and the patch to avoid triggering tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac: sdio: Disable auto-tuning around commands expected to fail"). Though both patches handle issues with Broadcom's AOS, the problems are distinct: 1. We want to defer (but not ignore) asynchronous (like timer-requested) tuning requests till the card is awake. However, we want to ignore CRC errors during the transition, we don't want to queue deferred tuning request. 2. You could imagine that the AOS could implement retuning but we could still get errors while transitioning in and out of the AOS. Similarly you could imagine a seamless transition into and out of the AOS (with no CRC errors) even if the AOS couldn't handle tuning. ALSO NOTE: presumably there is never a desperate need to retune in order to wake up the card, since doing so is impossible. Luckily the only way the card can get into sleep state is if we had a good enough tuning to send it the command to put it into sleep, so presumably that "good enough" tuning is enough to wake us up, at least with a few retries. Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Douglas Anderson authored
commit 2de0b42d upstream. There are certain cases, notably when transitioning between sleep and active state, when Broadcom SDIO WiFi cards will produce errors on the SDIO bus. This is evident from the source code where you can see that we try commands in a loop until we either get success or we've tried too many times. The comment in the code reinforces this by saying "just one write attempt may fail" Unfortunately these failures sometimes end up causing an "-EILSEQ" back to the core which triggers a retuning of the SDIO card and that blocks all traffic to the card until it's done. Let's disable retuning around the commands we expect might fail. Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Douglas Anderson authored
commit abdd5dcc upstream. This reverts commit 29f65891. After that patch landed I find that my kernel log on rk3288-veyron-minnie and rk3288-veyron-speedy is filled with: brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110 This seems to happen every time the Broadcom WiFi transitions out of sleep mode. Reverting the commit fixes the problem for me, so that's what this patch does. Note that, in general, the justification in the original commit seemed a little weak. It looked like someone was testing on a SD card controller that would sometimes die if there were CRC errors on the bus. This used to happen back in early days of dw_mmc (the controller on my boards), but we fixed it. Disabling a feature on all boards just because one SD card controller is broken seems bad. Fixes: 29f65891 ("brcmfmac: disable command decode in sdio_aos") Cc: Wright Feng <wright.feng@cypress.com> Cc: Double Lo <double.lo@cypress.com> Cc: Madhan Mohan R <madhanmohan.r@cypress.com> Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Cc: stable@vger.kernel.org Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mike Salvatore authored
commit 156e4299 upstream. Each function that manipulates the aa_ext struct should reset it's "pos" member on failure. This ensures that, on failure, no changes are made to the state of the aa_ext struct. There are paths were elements are optional and the error path is used to indicate the optional element is not present. This means instead of just aborting on error the unpack stream can become unsynchronized on optional elements, if using one of the affected functions. Cc: stable@vger.kernel.org Fixes: 736ec752 ("AppArmor: policy routines for loading and unpacking policy") Signed-off-by: Mike Salvatore <mike.salvatore@canonical.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jann Horn authored
commit 8404d7a6 upstream. A packed AppArmor policy contains null-terminated tag strings that are read by unpack_nameX(). However, unpack_nameX() uses string functions on them without ensuring that they are actually null-terminated, potentially leading to out-of-bounds accesses. Make sure that the tag string is null-terminated before passing it to strcmp(). Cc: stable@vger.kernel.org Fixes: 736ec752 ("AppArmor: policy routines for loading and unpacking policy") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
John Johansen authored
commit 23375b13 upstream. While commit 11c236b8 ("apparmor: add a default null dfa") ensure every profile has a policy.dfa it does not resize the policy.start[] to have entries for every possible start value. Which means PROFILE_MEDIATES is not safe to use on untrusted input. Unforunately commit b9590ad4 ("apparmor: remove POLICY_MEDIATES_SAFE") did not take into account the start value usage. The input string in profile_query_cb() is user controlled and is not properly checked to be within the limited start[] entries, even worse it can't be as userspace policy is allowed to make us of entries types the kernel does not know about. This mean usespace can currently cause the kernel to access memory up to 240 entries beyond the start array bounds. Cc: stable@vger.kernel.org Fixes: b9590ad4 ("apparmor: remove POLICY_MEDIATES_SAFE") Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Daniel Smith authored
commit 0e658060 upstream. On Chuwi Hi10 Plus, the Silead device id is MSSL0017. Signed-off-by: Daniel Smith <danct12@disroot.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Andrey Smirnov authored
commit 7c7da40d upstream. In the case of compat syscall ioctl numbers for UI_BEGIN_FF_UPLOAD and UI_END_FF_UPLOAD need to be adjusted before being passed on uinput_ioctl_handler() since code built with -m32 will be passing slightly different values. Extend the code already covering UI_SET_PHYS to cover UI_BEGIN_FF_UPLOAD and UI_END_FF_UPLOAD as well. Reported-by: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Mikhaylenko authored
commit 9843f3e0 upstream. They are capable of using intertouch and it works well with psmouse.synaptics_intertouch=1, so add them to the list. Without it, scrolling and gestures are jumpy, three-finger pinch gesture doesn't work and three- or four-finger swipes sometimes get stuck. Signed-off-by: Alexander Mikhaylenko <exalm7659@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Crt Mori authored
commit 389fc70b upstream. Register EE_VERSION contains mixture of calibration information and DSP version. So far, because calibrations were definite, the driver compatibility depended on whole contents, but in the newer production process the calibration part changes. Because of that, value in EE_VERSION will be changed and to avoid that calibration value is same as DSP version the MSB in calibration part was fixed to 1. That means existing calibrations (medical and consumer) will now have hex values (bits 8 to 15) of 83 and 84 respectively. Driver compatibility should be based only on DSP version part of the EE_VERSION (bits 0 to 7) register. Signed-off-by: Crt Mori <cmo@melexis.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lorenzo Bianconi authored
commit bce0d57d upstream. Properly suspend/resume i2c slaves connected to st_lsm6dsx master controller if the CPU goes in suspended state Fixes: c91c1c84 ("imu: st_lsm6dsx: add i2c embedded controller support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mike Marciniszyn authored
commit 3230f4a8 upstream. The following warning can happen when a memory shortage occurs during txreq allocation: [10220.939246] SLUB: Unable to allocate memory on node -1, gfp=0xa20(GFP_ATOMIC) [10220.939246] Hardware name: Intel Corporation S2600WT2R/S2600WT2R, BIOS SE5C610.86B.01.01.0018.C4.072020161249 07/20/2016 [10220.939247] cache: mnt_cache, object size: 384, buffer size: 384, default order: 2, min order: 0 [10220.939260] Workqueue: hfi0_0 _hfi1_do_send [hfi1] [10220.939261] node 0: slabs: 1026568, objs: 43115856, free: 0 [10220.939262] Call Trace: [10220.939262] node 1: slabs: 820872, objs: 34476624, free: 0 [10220.939263] dump_stack+0x5a/0x73 [10220.939265] warn_alloc+0x103/0x190 [10220.939267] ? wake_all_kswapds+0x54/0x8b [10220.939268] __alloc_pages_slowpath+0x86c/0xa2e [10220.939270] ? __alloc_pages_nodemask+0x2fe/0x320 [10220.939271] __alloc_pages_nodemask+0x2fe/0x320 [10220.939273] new_slab+0x475/0x550 [10220.939275] ___slab_alloc+0x36c/0x520 [10220.939287] ? hfi1_make_rc_req+0x90/0x18b0 [hfi1] [10220.939299] ? __get_txreq+0x54/0x160 [hfi1] [10220.939310] ? hfi1_make_rc_req+0x90/0x18b0 [hfi1] [10220.939312] __slab_alloc+0x40/0x61 [10220.939323] ? hfi1_make_rc_req+0x90/0x18b0 [hfi1] [10220.939325] kmem_cache_alloc+0x181/0x1b0 [10220.939336] hfi1_make_rc_req+0x90/0x18b0 [hfi1] [10220.939348] ? hfi1_verbs_send_dma+0x386/0xa10 [hfi1] [10220.939359] ? find_prev_entry+0xb0/0xb0 [hfi1] [10220.939371] hfi1_do_send+0x1d9/0x3f0 [hfi1] [10220.939372] process_one_work+0x171/0x380 [10220.939374] worker_thread+0x49/0x3f0 [10220.939375] kthread+0xf8/0x130 [10220.939377] ? max_active_store+0x80/0x80 [10220.939378] ? kthread_bind+0x10/0x10 [10220.939379] ret_from_fork+0x35/0x40 [10220.939381] SLUB: Unable to allocate memory on node -1, gfp=0xa20(GFP_ATOMIC) The shortage is handled properly so the message isn't needed. Silence by adding the no warn option to the slab allocation. Fixes: 45842abb ("staging/rdma/hfi1: move txreq header code") Cc: <stable@vger.kernel.org> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mike Marciniszyn authored
commit cc78076a upstream. The qp priv rcd pointer doesn't match the context being used for verbs causing issues when 9B and kdeth packets are processed by different receive contexts and hence different CPUs. When running on different CPUs the following panic can occur: WARNING: CPU: 3 PID: 2584 at lib/list_debug.c:59 __list_del_entry+0xa1/0xd0 list_del corruption. prev->next should be ffff9a7ac31f7a30, but was ffff9a7c3bc89230 CPU: 3 PID: 2584 Comm: z_wr_iss Kdump: loaded Tainted: P OE ------------ 3.10.0-862.2.3.el7_lustre.x86_64 #1 Call Trace: <IRQ> [<ffffffffb7b0d78e>] dump_stack+0x19/0x1b [<ffffffffb74916d8>] __warn+0xd8/0x100 [<ffffffffb749175f>] warn_slowpath_fmt+0x5f/0x80 [<ffffffffb7768671>] __list_del_entry+0xa1/0xd0 [<ffffffffc0c7a945>] process_rcv_qp_work+0xb5/0x160 [hfi1] [<ffffffffc0c7bc2b>] handle_receive_interrupt_nodma_rtail+0x20b/0x2b0 [hfi1] [<ffffffffc0c70683>] receive_context_interrupt+0x23/0x40 [hfi1] [<ffffffffb7540a94>] __handle_irq_event_percpu+0x44/0x1c0 [<ffffffffb7540c42>] handle_irq_event_percpu+0x32/0x80 [<ffffffffb7540ccc>] handle_irq_event+0x3c/0x60 [<ffffffffb7543a1f>] handle_edge_irq+0x7f/0x150 [<ffffffffb742d504>] handle_irq+0xe4/0x1a0 [<ffffffffb7b23f7d>] do_IRQ+0x4d/0xf0 [<ffffffffb7b16362>] common_interrupt+0x162/0x162 <EOI> [<ffffffffb775a326>] ? memcpy+0x6/0x110 [<ffffffffc109210d>] ? abd_copy_from_buf_off_cb+0x1d/0x30 [zfs] [<ffffffffc10920f0>] ? abd_copy_to_buf_off_cb+0x30/0x30 [zfs] [<ffffffffc1093257>] abd_iterate_func+0x97/0x120 [zfs] [<ffffffffc10934d9>] abd_copy_from_buf_off+0x39/0x60 [zfs] [<ffffffffc109b828>] arc_write_ready+0x178/0x300 [zfs] [<ffffffffb7b11032>] ? mutex_lock+0x12/0x2f [<ffffffffb7b11032>] ? mutex_lock+0x12/0x2f [<ffffffffc1164d05>] zio_ready+0x65/0x3d0 [zfs] [<ffffffffc04d725e>] ? tsd_get_by_thread+0x2e/0x50 [spl] [<ffffffffc04d1318>] ? taskq_member+0x18/0x30 [spl] [<ffffffffc115ef22>] zio_execute+0xa2/0x100 [zfs] [<ffffffffc04d1d2c>] taskq_thread+0x2ac/0x4f0 [spl] [<ffffffffb74cee80>] ? wake_up_state+0x20/0x20 [<ffffffffc115ee80>] ? zio_taskq_member.isra.7.constprop.10+0x80/0x80 [zfs] [<ffffffffc04d1a80>] ? taskq_thread_spawn+0x60/0x60 [spl] [<ffffffffb74bae31>] kthread+0xd1/0xe0 [<ffffffffb74bad60>] ? insert_kthread_work+0x40/0x40 [<ffffffffb7b1f5f7>] ret_from_fork_nospec_begin+0x21/0x21 [<ffffffffb74bad60>] ? insert_kthread_work+0x40/0x40 Fix by reading the map entry in the same manner as the hardware so that the kdeth and verbs contexts match. Cc: <stable@vger.kernel.org> Fixes: 5190f052 ("IB/hfi1: Allow the driver to initialize QP priv struct") Reviewed-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mike Marciniszyn authored
commit cf131a81 upstream. Heavy contention of the sde flushlist_lock can cause hard lockups at extreme scale when the flushing logic is under stress. Mitigate by replacing the item at a time copy to the local list with an O(1) list_splice_init() and using the high priority work queue to do the flushes. Fixes: 77241056 ("IB/hfi1: add driver files") Cc: <stable@vger.kernel.org> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mike Marciniszyn authored
commit da9de5f8 upstream. The call to sdma_progress() is called outside the wait lock. In this case, there is a race condition where sdma_progress() can return false and the sdma_engine can idle. If that happens, there will be no more sdma interrupts to cause the wakeup and the user_sdma xmit will hang. Fix by moving the lock to enclose the sdma_progress() call. Also, delete busycount. The need for this was removed by: commit bcad2913 ("IB/hfi1: Serve the most starved iowait entry first") Cc: <stable@vger.kernel.org> Fixes: 77241056 ("IB/hfi1: add driver files") Reviewed-by: Gary Leshner <Gary.S.Leshner@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kaike Wan authored
commit 5f90677e upstream. The opcode range for fault injection from user should be validated before it is applied to the fault->opcodes[] bitmap to avoid out-of-bound error. Cc: <stable@vger.kernel.org> Fixes: a74d5307 ("IB/hfi1: Rework fault injection machinery") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ronnie Sahlberg authored
commit 61cabc7b upstream. We can not hold the GlobalMid_Lock spinlock during the dfs processing in cifs_reconnect since it invokes things that may sleep and thus trigger : BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:23 Thus we need to drop the spinlock during this code block. RHBZ: 1716743 Cc: stable@vger.kernel.org Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ronnie Sahlberg authored
commit 487317c9 upstream. We can not depend on the tcon->open_file_lock here since in multiuser mode we may have the same file/inode open via multiple different tcons. The current code is race prone and will crash if one user deletes a file at the same time a different user opens/create the file. To avoid this we need to have a spinlock attached to the inode and not the tcon. RHBZ: 1580165 CC: Stable <stable@vger.kernel.org> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Nyman authored
commit b8c3b718 upstream. A USB3 device needs to be reset and re-enumarated if the port it connects to goes to a error state, with link state inactive. There is no use in trying to recover failed transactions by resetting endpoints at this stage. Tests show that in rare cases, after multiple endpoint resets of a roothub port the whole host controller might stop completely. Several retries to recover from transaction error can happen as it can take a long time before the hub thread discovers the USB3 port error and inactive link. We can't reliably detect the port error from slot or endpoint context due to a limitation in xhci, see xhci specs section 4.8.3: "There are several cases where the EP State field in the Output Endpoint Context may not reflect the current state of an endpoint" and "Software should maintain an accurate value for EP State, by tracking it with an internal variable that is driven by Events and Doorbell accesses" Same appears to be true for slot state. set a flag to the corresponding slot if a USB3 roothub port link goes inactive to prevent both queueing new URBs and resetting endpoints. Reported-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com> Tested-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Nyman authored
commit ddd57980 upstream. USB 3.2 capability in a host can be detected from the xHCI Supported Protocol Capability major and minor revision fields. If major is 0x3 and minor 0x20 then the host is USB 3.2 capable. For USB 3.2 capable hosts set the root hub lane count to 2. The Major Revision and Minor Revision fields contain a BCD version number. The value of the Major Revision field is JJh and the value of the Minor Revision field is MNh for version JJ.M.N, where JJ = major revision number, M - minor version number, N = sub-minor version number, e.g. version 3.1 is represented with a value of 0310h. Also fix the extra whitespace printed out when announcing regular SuperSpeed hosts. Cc: <stable@vger.kernel.org> # v4.18+ Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Chen authored
commit c19dffc0 upstream. An endpoint conflict occurs when the USB is working in device mode during an isochronous communication. When the endpointA IN direction is an isochronous IN endpoint, and the host sends an IN token to endpointA on another device, then the OUT transaction may be missed regardless the OUT endpoint number. Generally, this occurs when the device is connected to the host through a hub and other devices are connected to the same hub. The affected OUT endpoint can be either control, bulk, isochronous, or an interrupt endpoint. After the OUT endpoint is primed, if an IN token to the same endpoint number on another device is received, then the OUT endpoint may be unprimed (cannot be detected by software), which causes this endpoint to no longer respond to the host OUT token, and thus, no corresponding interrupt occurs. There is no good workaround for this issue, the only thing the software could do is numbering isochronous IN from the highest endpoint since we have observed most of device number endpoint from the lowest. Cc: <stable@vger.kernel.org> #v3.14+ Cc: Fabio Estevam <festevam@gmail.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: Jun Li <jun.li@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Stanley Chu authored
commit 24e2e7a1 upstream. UFS runtime suspend can be triggered after pm_runtime_enable() is invoked in ufshcd_pltfrm_init(). However if the first runtime suspend is triggered before binding ufs_hba structure to ufs device structure via platform_set_drvdata(), then UFS runtime suspend will be no longer triggered in the future because its dev->power.runtime_error was set in the first triggering and does not have any chance to be cleared. To be more clear, dev->power.runtime_error is set if hba is NULL in ufshcd_runtime_suspend() which returns -EINVAL to rpm_callback() where dev->power.runtime_error is set as -EINVAL. In this case, any future rpm_suspend() for UFS device fails because rpm_check_suspend_allowed() fails due to non-zero dev->power.runtime_error. To resolve this issue, make sure the first UFS runtime suspend get valid "hba" in ufshcd_runtime_suspend(): Enable UFS runtime PM only after hba is successfully bound to UFS device structure. Fixes: 62694735 ([SCSI] ufs: Add runtime PM support for UFS host controller driver) Cc: stable@vger.kernel.org Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ulf Hansson authored
commit 83293386 upstream. Processing of SDIO IRQs must obviously be prevented while the card is system suspended, otherwise we may end up trying to communicate with an uninitialized SDIO card. Reports throughout the years shows that this is not only a theoretical problem, but a real issue. So, let's finally fix this problem, by keeping track of the state for the card and bail out before processing the SDIO IRQ, in case the card is suspended. Cc: stable@vger.kernel.org Reported-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Douglas Anderson authored
commit b4c9f938 upstream. We want SDIO drivers to be able to temporarily stop retuning when the driver knows that the SDIO card is not in a state where retuning will work (maybe because the card is asleep). We'll move the relevant functions to a place where drivers can call them. Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Douglas Anderson authored
commit 0a55f4ab upstream. Normally when the MMC core sees an "-EILSEQ" error returned by a host controller then it will trigger a retuning of the card. This is generally a good idea. However, if a command is expected to sometimes cause transfer errors then these transfer errors shouldn't cause a re-tuning. This re-tuning will be a needless waste of time. One example case where a transfer is expected to cause errors is when transitioning between idle (sometimes referred to as "sleep" in Broadcom code) and active state on certain Broadcom WiFi SDIO cards. Specifically if the card was already transitioning between states when the command was sent it could cause an error on the SDIO bus. Let's add an API that the SDIO function drivers can call that will temporarily disable the auto-tuning functionality. Then we can add a call to this in the Broadcom WiFi driver and any other driver that might have similar needs. NOTE: this makes the assumption that the card is already tuned well enough that it's OK to disable the auto-retuning during one of these error-prone situations. Presumably the driver code performing the error-prone transfer knows how to recover / retry from errors. ...and after we can get back to a state where transfers are no longer error-prone then we can enable the auto-retuning again. If we truly find ourselves in a case where the card needs to be retuned sometimes to handle one of these error-prone transfers then we can always try a few transfers first without auto-retuning and then re-try with auto-retuning if the first few fail. Without this change on rk3288-veyron-minnie I periodically see this in the logs of a machine just sitting there idle: dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
jjian zhou authored
commit 20314ce3 upstream. If cmd19 timeout or response crcerr occurs during execute_tuning(), it need invoke msdc_reset_hw(). Otherwise SDIO IRQ can't be detected. Signed-off-by: jjian zhou <jjian.zhou@mediatek.com> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by: Yong Mao <yong.mao@mediatek.com> Fixes: 5215b2e9 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
jjian zhou authored
commit 8a5df8ac upstream. SDIO IRQ is triggered by low level. It need disable SDIO IRQ detected function. Otherwise the interrupt register can't be cleared. It will process the interrupt more. Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by: Yong Mao <yong.mao@mediatek.com> Fixes: 5215b2e9 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Wolfram Sang authored
commit 97bf85b6 upstream. Our HW engineers informed us that HS400 is not working on these SoC revisions. Fixes: 0f4e2054 ("mmc: renesas_sdhi: disable HS400 on H3 ES1.x and M3-W ES1.[012]") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Raul E Rangel authored
commit 0f7b79a4 upstream. The O2Micro controller only supports tuning at 4-bits. So the host driver needs to change the bus width while tuning and then set it back when done. There was a bug in the original implementation in that mmc->ios.bus_width also wasn't updated. Thus setting the incorrect blocksize in sdhci_send_tuning which results in a tuning failure. Signed-off-by: Raul E Rangel <rrangel@chromium.org> Fixes: 0086fc21 ("mmc: sdhci: Add support for O2 hardware tuning") Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Miguel Ojeda authored
commit 0c97bf86 upstream. Starting with GCC 9, -Warray-bounds detects cases when memset is called starting on a member of a struct but the size to be cleared ends up writing over further members. Such a call happens in the trace code to clear, at once, all members after and including `seq` on struct trace_iterator: In function 'memset', inlined from 'ftrace_dump' at kernel/trace/trace.c:8914:3: ./include/linux/string.h:344:9: warning: '__builtin_memset' offset [8505, 8560] from the object at 'iter' is out of the bounds of referenced subobject 'seq' with type 'struct trace_seq' at offset 4368 [-Warray-bounds] 344 | return __builtin_memset(p, c, size); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ In order to avoid GCC complaining about it, we compute the address ourselves by adding the offsetof distance instead of referring directly to the member. Since there are two places doing this clear (trace.c and trace_kdb.c), take the chance to move the workaround into a single place in the internal header. Link: http://lkml.kernel.org/r/20190523124535.GA12931@gmail.comSigned-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> [ Removed unnecessary parenthesis around "iter" ] Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 22 Jun, 2019 10 commits
-
-
Greg Kroah-Hartman authored
-
Eric Dumazet authored
commit b6653b36 upstream. tcp_fragment() might be called for skbs in the write queue. Memory limits might have been exceeded because tcp_sendmsg() only checks limits at full skb (64KB) boundaries. Therefore, we need to make sure tcp_fragment() wont punish applications that might have setup very low SO_SNDBUF values. Fixes: f070ef2a ("tcp: tcp_fragment() should apply sane memory limits") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Christoph Paasch <cpaasch@apple.com> Tested-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
-
Andrea Arcangeli authored
commit 59ea6d06 upstream. When fixing the race conditions between the coredump and the mmap_sem holders outside the context of the process, we focused on mmget_not_zero()/get_task_mm() callers in 04f5866e ("coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping"), but those aren't the only cases where the mmap_sem can be taken outside of the context of the process as Michal Hocko noticed while backporting that commit to older -stable kernels. If mmgrab() is called in the context of the process, but then the mm_count reference is transferred outside the context of the process, that can also be a problem if the mmap_sem has to be taken for writing through that mm_count reference. khugepaged registration calls mmgrab() in the context of the process, but the mmap_sem for writing is taken later in the context of the khugepaged kernel thread. collapse_huge_page() after taking the mmap_sem for writing doesn't modify any vma, so it's not obvious that it could cause a problem to the coredump, but it happens to modify the pmd in a way that breaks an invariant that pmd_trans_huge_lock() relies upon. collapse_huge_page() needs the mmap_sem for writing just to block concurrent page faults that call pmd_trans_huge_lock(). Specifically the invariant that "!pmd_trans_huge()" cannot become a "pmd_trans_huge()" doesn't hold while collapse_huge_page() runs. The coredump will call __get_user_pages() without mmap_sem for reading, which eventually can invoke a lockless page fault which will need a functional pmd_trans_huge_lock(). So collapse_huge_page() needs to use mmget_still_valid() to check it's not running concurrently with the coredump... as long as the coredump can invoke page faults without holding the mmap_sem for reading. This has "Fixes: khugepaged" to facilitate backporting, but in my view it's more a bug in the coredump code that will eventually have to be rewritten to stop invoking page faults without the mmap_sem for reading. So the long term plan is still to drop all mmget_still_valid(). Link: http://lkml.kernel.org/r/20190607161558.32104-1-aarcange@redhat.com Fixes: ba76149f ("thp: khugepaged") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Michal Hocko <mhocko@suse.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Cc: Jason Gunthorpe <jgg@mellanox.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sagi Grimberg authored
commit 64861993 upstream. When the controller supports less queues than requested, we should make sure that queue mapping does the right thing and not assume that all queues are available. This fixes a crash when the controller supports less queues than requested. The rules are: 1. if no write queues are requested, we assign the available queues to the default queue map. The default and read queue maps share the existing queues. 2. if write queues are requested: - first make sure that read queue map gets the requested nr_io_queues count - then grant the default queue map the minimum between the requested nr_write_queues and the remaining queues. If there are no available queues to dedicate to the default queue map, fallback to (1) and share all the queues in the existing queue map. Also, provide a log indication on how we constructed the different queue maps. Reported-by: Harris, James R <james.r.harris@intel.com> Tested-by: Jim Harris <james.r.harris@intel.com> Cc: <stable@vger.kernel.org> # v5.0+ Suggested-by: Roy Shterman <roys@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sagi Grimberg authored
commit f34e2589 upstream. If I/O queue connect times out, we might have freed the queue socket already, so check for that on the error path in nvme_tcp_start_queue. Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sagi Grimberg authored
commit efb973b1 upstream. usually nvme_ prefix is for core functions. While we're cleaning up, remove redundant empty lines Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Minwoo Im <minwoo.im@samsung.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Yang Shi authored
commit 7a30df49 upstream. A few new fields were added to mmu_gather to make TLB flush smarter for huge page by telling what level of page table is changed. __tlb_reset_range() is used to reset all these page table state to unchanged, which is called by TLB flush for parallel mapping changes for the same range under non-exclusive lock (i.e. read mmap_sem). Before commit dd2283f2 ("mm: mmap: zap pages with read mmap_sem in munmap"), the syscalls (e.g. MADV_DONTNEED, MADV_FREE) which may update PTEs in parallel don't remove page tables. But, the forementioned commit may do munmap() under read mmap_sem and free page tables. This may result in program hang on aarch64 reported by Jan Stancek. The problem could be reproduced by his test program with slightly modified below. ---8<--- static int map_size = 4096; static int num_iter = 500; static long threads_total; static void *distant_area; void *map_write_unmap(void *ptr) { int *fd = ptr; unsigned char *map_address; int i, j = 0; for (i = 0; i < num_iter; i++) { map_address = mmap(distant_area, (size_t) map_size, PROT_WRITE | PROT_READ, MAP_SHARED | MAP_ANONYMOUS, -1, 0); if (map_address == MAP_FAILED) { perror("mmap"); exit(1); } for (j = 0; j < map_size; j++) map_address[j] = 'b'; if (munmap(map_address, map_size) == -1) { perror("munmap"); exit(1); } } return NULL; } void *dummy(void *ptr) { return NULL; } int main(void) { pthread_t thid[2]; /* hint for mmap in map_write_unmap() */ distant_area = mmap(0, DISTANT_MMAP_SIZE, PROT_WRITE | PROT_READ, MAP_ANONYMOUS | MAP_PRIVATE, -1, 0); munmap(distant_area, (size_t)DISTANT_MMAP_SIZE); distant_area += DISTANT_MMAP_SIZE / 2; while (1) { pthread_create(&thid[0], NULL, map_write_unmap, NULL); pthread_create(&thid[1], NULL, dummy, NULL); pthread_join(thid[0], NULL); pthread_join(thid[1], NULL); } } ---8<--- The program may bring in parallel execution like below: t1 t2 munmap(map_address) downgrade_write(&mm->mmap_sem); unmap_region() tlb_gather_mmu() inc_tlb_flush_pending(tlb->mm); free_pgtables() tlb->freed_tables = 1 tlb->cleared_pmds = 1 pthread_exit() madvise(thread_stack, 8M, MADV_DONTNEED) zap_page_range() tlb_gather_mmu() inc_tlb_flush_pending(tlb->mm); tlb_finish_mmu() if (mm_tlb_flush_nested(tlb->mm)) __tlb_reset_range() __tlb_reset_range() would reset freed_tables and cleared_* bits, but this may cause inconsistency for munmap() which do free page tables. Then it may result in some architectures, e.g. aarch64, may not flush TLB completely as expected to have stale TLB entries remained. Use fullmm flush since it yields much better performance on aarch64 and non-fullmm doesn't yields significant difference on x86. The original proposed fix came from Jan Stancek who mainly debugged this issue, I just wrapped up everything together. Jan's testing results: v5.2-rc2-24-gbec7550c -------------------------- mean stddev real 37.382 2.780 user 1.420 0.078 sys 54.658 1.855 v5.2-rc2-24-gbec7550c + "mm: mmu_gather: remove __tlb_reset_range() for force flush" ---------------------------------------------------------------------------------------_ mean stddev real 37.119 2.105 user 1.548 0.087 sys 55.698 1.357 [akpm@linux-foundation.org: coding-style fixes] Link: http://lkml.kernel.org/r/1558322252-113575-1-git-send-email-yang.shi@linux.alibaba.com Fixes: dd2283f2 ("mm: mmap: zap pages with read mmap_sem in munmap") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Signed-off-by: Jan Stancek <jstancek@redhat.com> Reported-by: Jan Stancek <jstancek@redhat.com> Tested-by: Jan Stancek <jstancek@redhat.com> Suggested-by: Will Deacon <will.deacon@arm.com> Tested-by: Will Deacon <will.deacon@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Nick Piggin <npiggin@gmail.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com> Cc: Nadav Amit <namit@vmware.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Mel Gorman <mgorman@suse.de> Cc: <stable@vger.kernel.org> [4.20+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Tobin C. Harding authored
[ Upstream commit b9fba67b ] If a call to kobject_init_and_add() fails we should call kobject_put() otherwise we leak memory. Add call to kobject_put() in the error path of call to kobject_init_and_add(). Please note, this has the side effect that the release method is called if kobject_init_and_add() fails. Link: http://lkml.kernel.org/r/20190513033458.2824-1-tobin@kernel.orgSigned-off-by: Tobin C. Harding <tobin@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Amit Cohen authored
[ Upstream commit 275e928f ] Force of 56G is not supported by hardware in Ethernet devices. This configuration fails with a bad parameter error from firmware. Add check of this case. Instead of trying to set 56G with autoneg off, return a meaningful error. Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Amit Cohen <amitc@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-