Two PHY bugs are fixed by IC logic, but these bits are not
enabled by default, so we enable them at driver.
The two bugs are: MXS_PHY_ABNORMAL_IN_SUSPEND and MXS_PHY_SENDING_SOF_TOO_FAST
which are described at code.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Change "high speed" to "HS"
Change "non-high speed" to "FS/LS"

Implementation of notify_suspend and notify_resume will be different
according to mxs_phy_data->flags.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

It is needed by imx6 SoC series, but not for imx23 and imx28.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add anatop phandle which is used to access anatop registers to
control PHY's power and other USB operations.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The auto setting is used to open related power and clocks
automatically after receiving wakeup signal.

With this feature, the PHY's clock and power can be recovered
correctly from low power mode, it is guaranteed by IC logic.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The mxs-phy has several bugs and features at different
versions, the driver code can get it through of_device_id.data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add "fsl,imx6q-usbphy" for imx6dq and imx6dl, add
"fsl,imx6sl-usbphy" for imx6sl, and "fsl,imx23-usbphy"
is still a fallback for other strings.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds suspend/resume support to s3c-hsotg driver. It makes UDC
driver more power efficient.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Reprogramming the DMA after tear down is initiated leads to warning.
This is mainly seen with ISOCH since we do a delayed completion for
ISOCH transfers. In ISOCH transfers dma_completion should not reprogram
if the channel tear down is initiated.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Adapted dwc3 core to use the Generic PHY Framework. So for init, exit,
power_on and power_off the following APIs are used phy_init(), phy_exit(),
phy_power_on() and phy_power_off().

However using the old USB phy library wont be removed till the PHYs of all
other SoC's using dwc3 core is adapted to the Generic PHY Framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since PHYs for dwc3 is optional (not all SoCs having PHYs for DWC3
should be programmed), do not return from probe if the USB PHY library
returns -ENODEV as that indicates the platform does not have a
programmable PHY.

While this can be considered as a temporary fix, a long term solution
would be to add 'nop' PHY for platforms that does not have programmable
PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since now we have a separate folder for phy, move the PHY dt binding
documentation of TI to that folder.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

few new revisions of the core have been released,
add them to our list of revisions so we can apply
workarounds if necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>

commit 388e5c51 (usb: dwc3: remove dwc3 dependency
on host AND gadget.) created the possibility for
host-only and peripheral-only dwc3 builds but
left a possible randconfig build error when host-only
builds are selected.

Cc: <stable@vger.kernel.org> # v3.8+
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

we need to pre-start stream transfers otherwise we
will never know when to start them.
Signed-off-by: Felipe Balbi <balbi@ti.com>

When going into bus suspend/resume we _must_
call gadget driver's ->suspend/->resume callbacks
accordingly. This patch implements that very feature
which has been missing forever.
Signed-off-by: Felipe Balbi <balbi@ti.com>

It's not always we need to force a transfer to be removed
from the core's internal cache. This extra argument will
help differentiating those two cases.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

During superspeed, HIRD threshold should always
be zero. Curent driver wasn't making sure that
was the case.
Signed-off-by: Felipe Balbi <balbi@ti.com>

if we have hibernation configured, Databook
instructs us to set KEEP_CONNECT bit together
with RUN_STOP bit, in step 9 of section 12.3.6.1
Initialization for Hibernation Support.
Signed-off-by: Felipe Balbi <balbi@ti.com>

no functional changes, just converting spaces
into tab.
Signed-off-by: Felipe Balbi <balbi@ti.com>

We must read HWPARAMS4 register to figure out
how many scratch buffers we should allocate.

Later patch will use "Set Scratchpad Buffer
Array" command to pass the pointer to the
IP so it can be used during hibernation.
Signed-off-by: Felipe Balbi <balbi@ti.com>

That argument will be used in later patches when we
have working hibernation support. For now, always
pass it as false.

The idea of this patch is to decrease to size of
following patches and slowly add hibernation building
blocks to the gadget side of dwc3 so that it becomes
very easy to review the actual hibernation code.

[ balbi@ti.com : rewrote patch on top of current
	tree. Added commit log. ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This function will be used during hibernation to get
the current link state. It will be needed at least
for Hibernation support.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This extra field will save endpoint state when we're
about to enter hibernation. It will be used later
to restore the endpoint state when resuming.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

this will tell driver that this version
of the core was configured with hibernation
feature enabled.
Signed-off-by: Felipe Balbi <balbi@ti.com>

move 1-bit flags to the bottom of the structure,
sort all bit flags alphabetically, add documentation
which was missing.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Revision 2.20a of the core has a known issue
which would generate bogus hibernation events
_and_ random failures on USB CV TD.9.23 test
case.

The suggested workaround is to ignore hibernation
events which don't match currently connected
speed.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Revisions between 2.10a and 2.50a (included) have
a known issue which may cause xHCI compliance tests
to fail and/or quality issues with Isochronous
transactions.

Note that this issue only impacts certain configurations
of those revisions, namely the ones which have clock
gating enabled.

The suggested workaround is to disable clock gating in
known broken revisions, make sure HW LPM is disabled
and set GCTL.SOFITPSYNC to 1.
Signed-off-by: Felipe Balbi <balbi@ti.com>

This bit is necessary for implemeting workaround
for known issue with some revisions of this core.
Signed-off-by: Felipe Balbi <balbi@ti.com>

by setting IOC always, we can recycle TRBs a
lot sooner at the expense of some increased
CPU load.

The extra load seems to be quite minimal on
OMAP5 devices (instead of 1 IRQ for one MSC
transfer, we get
CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS).
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch fixes problem with unnecessary usb_ep_set_maxpacket_limit() usage.
It should not be used in at91udc_probe() function, where maxpacket values are
set for field "maxpacket" of struct at91_ep, which is representation of
endpoint in driver internals. Function usb_ep_set_maxpacket_limit() is called
in udc_reinit() function, where struct usb_ep instances are initialised with
values set previously in struct at91_ep instances. So it's very important to
initialise it properly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If NO_DMA=y:

    drivers/built-in.o: In function `txstate':
    musb_gadget.c:(.text+0x35955a): undefined reference to `dma_unmap_single'
    musb_gadget.c:(.text+0x35957e): undefined reference to `dma_sync_single_for_cpu'
    drivers/built-in.o: In function `musb_g_giveback':
    (.text+0x359672): undefined reference to `dma_mapping_error'
    drivers/built-in.o: In function `musb_g_giveback':
    (.text+0x3596ba): undefined reference to `dma_unmap_single'
    drivers/built-in.o: In function `musb_g_giveback':
    (.text+0x3596e0): undefined reference to `dma_sync_single_for_cpu'
    drivers/built-in.o: In function `rxstate':
    musb_gadget.c:(.text+0x3599d0): undefined reference to `dma_unmap_single'
    musb_gadget.c:(.text+0x3599f6): undefined reference to `dma_sync_single_for_cpu'
    drivers/built-in.o: In function `musb_gadget_queue':
    musb_gadget.c:(.text+0x35a8c0): undefined reference to `dma_map_single'
    musb_gadget.c:(.text+0x35a8d0): undefined reference to `dma_mapping_error'
    musb_gadget.c:(.text+0x35a906): undefined reference to `dma_sync_single_for_cpu'
    musb_gadget.c:(.text+0x35a9a0): undefined reference to `dma_unmap_single'
    musb_gadget.c:(.text+0x35a9c8): undefined reference to `dma_sync_single_for_cpu'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The probe() method has the 'dev' local variable declared and used but strangely
not in all cases where it should be...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

instead of relying on the otg pointer, which
can be NULL in certain cases, we can use the
gadget and host pointers we already hold inside
struct musb.

Cc: <stable@vger.kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

debugfs files to show the contents of important dsps registers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.

Because of that, what used to be 8 bits long, has become 9 bits long.

Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.

So in dwc3_event_devt, the bit mask should be:
event_info	[24:16]		9 bits
reserved31_25	[31:25]		7 bits

This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.

[ balbi@ti.com : improve commit log a bit ]

Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Debugfs function return an ERR_PTR if they compiled out.  We don't need
to test for that here because if the debugfs file are compiled out then
it is ok to pass an ERR_PTR to debugfs_create_file() since it will just
be a no-op stub.

Debugfs return NULLs on error, but we don't need to test for that either
because debugfs_create_file() will accept NULL pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The SoCs earlier than sama5d3, they have the same number endpoints
and DMA channels. In driver code, they use the same definition
USBA_NR_ENDPOINTS for both endpoints and dma channels. However,
in sama5d3, it has different number for endpoints and DMA channels.
So, define a new macro USBA_NR_DMAs for DMA channels. And the
USBA_NR_ENDPOINS is not used anymore, remove it at the same time.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In sama5d3 SoC, there are 16 endpoints, which is different with
earlier SoCs (only have 7 endpoints). The USBA_NR_ENDPOINTS macro
is not suitable for sama5d3. So, get the endpoints number through
the udc->num_ep, which get from platform data for non-dt kernel,
or parse from dt node.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds asynchronous I/O support for FunctionFS endpoint files.
It adds ffs_epfile_aio_write() and ffs_epfile_aio_read() functions responsible
for preparing AIO operations.

It also modifies ffs_epfile_io() function, adding aio handling code. Instead
of extending list of parameters of this function, there is new struct
ffs_io_data which contains all information needed to perform I/O operation.
Pointer to this struct replaces "buf" and "len" parameters of ffs_epfile_io()
function. Allocated buffer is freed immediately only after sync operation,
because in async IO it's freed in complete funcion. For each async operation
an USB request is allocated, because it allows to have more than one request
queued on single endpoint.

According to changes in ffs_epfile_io() function, functions ffs_epfile_write()
and ffs_epfile_read() are updated to use new API.

For asynchronous I/O operations there is new request complete function named
ffs_epfile_async_io_complete(), which completes AIO operation, and frees
used memory.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>