The patch addresses the compliance test failures while running  TDA
2.3.1.1 and  TDA 2.3.1.2 of the "PD Communications Engine USB PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.

While the purpose of TDA 2.3.1.1 and  TDA 2.3.1.2 is to verify that
the static and dynamic electrical capabilities of a Source meet the
requirements for each PDO offered,  while doing so, the tests also
monitor that the timing of the VBUS waveform versus the messages meets
the requirements for Hard Reset defined in PROT-PROC-HR-TSTR as
mentioned in step 11 of TDA.2.3.1.1 and step 15 of TDA.2.3.1.2.

TDB.2.2.13.1: PROT-PROC-HR-TSTR Procedure and Checks for Tester
Originated Hard Reset
Purpose: To perform the appropriate protocol checks relating to any
circumstance in which the Hard Reset signal is sent by the Tester.

UUT is behaving as source:
The Tester sends a Hard Reset signal.
1. Check VBUS stays within present valid voltage range for
tPSHardReset min (25ms) after last bit of Hard Reset signal.
[PROT_PROC_HR_TSTR_1]
2. Check that VBUS starts to fall below present valid voltage range by
tPSHardReset max (35ms). [PROT_PROC_HR_TSTR_2]
3. Check that VBUS reaches vSafe0V within tSafe0v max (650 ms).
[PROT_PROC_HR_TSTR_3]
4. Check that VBUS starts rising to vSafe5V after a delay of
tSrcRecover (0.66s - 1s) from reaching vSafe0V. [PROT_PROC_HR_TSTR_4]
5. Check that VBUS reaches vSafe5V within tSrcTurnOn max (275ms) of
rising above vSafe0v max (0.8V). [PROT_PROC_HR_TSTR_5] Power Delivery
Compliance Plan 139 6. Check that Source Capabilities are finished
sending within tFirstSourceCap max (250ms) of VBUS reaching vSafe5v
min. [PROT_PROC_HR_TSTR_6].

This is in line with 7.1.5 Response to Hard Resets of the USB Power
Delivery Specification Revision 3.0, Version 1.2,
"Hard Reset Signaling indicates a communication failure has occurred
and the Source Shall stop driving VCONN, Shall remove Rp from the
VCONN pin and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The
USB connection May reset during a Hard Reset since the VBUS voltage
will be less than vSafe5V for an extended period of time. After
establishing the vSafe0V voltage condition on VBUS, the Source Shall
wait tSrcRecover before re-applying VCONN and restoring VBUS to
vSafe5V. A Source Shall conform to the VCONN timing as specified in
[USB Type-C 1.3]."

With the above guidelines from the spec in mind, TCPM does not turn
off VCONN while entering SRC_HARD_RESET_VBUS_OFF. The patch makes TCPM
turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF and turn it back
on while entering SRC_HARD_RESET_VBUS_ON along with vbus instead of
having VCONN on through hardreset.

Also, the spec clearly states that "After establishing the vSafe0V
voltage condition on VBUS",  the Source Shall wait tSrcRecover before
re-applying VCONN and restoring VBUS to vSafe5V.
TCPM does not conform to this requirement. If the TCPC driver calls
tcpm_vbus_change with vbus off signal, TCPM right away enters
SRC_HARD_RESET_VBUS_ON without waiting for tSrcRecover.
For TCPC's which are buggy/does not call tcpm_vbus_change, TCPM
assumes that the vsafe0v is instantaneous as TCPM only waits
tSrcRecover instead of waiting for tSafe0v + tSrcRecover.
This patch also fixes this behavior by making sure that TCPM waits for
tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON when
tcpm_vbus_change is called by TCPC.
When TCPC does not call tcpm_vbus_change, TCPM assumes the worst case
i.e.  tSafe0v + tSrcRecover before transitioning into
SRC_HARD_RESET_VBUS_ON.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200817184601.1899929-1-badhri@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The commit 2a6c0b82 ("USB: PHY: JZ4770: Add support for new
Ingenic SoCs.") introduced the initialization function for different
chips, but left the relevant code involved in the resetting process
in the original function, resulting in uninitialized variable calls.

Fixes: 2a6c0b82 ("USB: PHY: JZ4770: Add support for new Ingenic SoCs.").
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200825081654.18186-2-zhouyanjie@wanyeetech.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory.  Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.

Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some device drivers call libusb_clear_halt when target ep queue
is not empty. (eg. spice client connected to qemu for usb redir)

Before commit f5249461 ("xhci: Clear the host side toggle
manually when endpoint is soft reset"), that works well.
But now, we got the error log:

    EP not empty, refuse reset

xhci_endpoint_reset failed and left ep_state's EP_SOFT_CLEAR_TOGGLE
bit still set

So all the subsequent urb sumbits to the ep will fail with the
warn log:

    Can't enqueue URB while manually clearing toggle

We need to clear ep_state EP_SOFT_CLEAR_TOGGLE bit after
xhci_endpoint_reset, even if it failed.

Fixes: f5249461 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable <stable@vger.kernel.org> # v4.17+
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-4-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Sometimes re-plugging a USB device during system sleep renders the device
useless:
[  173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[  176.496485] usb 2-4: Waited 2000ms for CONNECT
[  176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[  176.497103] usb 2-4: can't resume, status -19
[  176.497438] usb usb2-port4: logical disconnect

Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.

So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dci is 0 based and xhci_get_ep_ctx() will do ep index increment to get
the ep context.

[rename dci to ep_index -Mathias]
Cc: stable <stable@vger.kernel.org> # v4.15+
Fixes: 02b6fdc2 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-2-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.

Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Link: https://lore.kernel.org/r/2b0585228b003eedcc82db84697b31477df152e0.1597803605.git.thinhn@synopsys.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Converting the Makefile to use the new tools buildsystem.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[fixes builds with O=...]
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200819071733.60028-1-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

USB: fixes for v5.9-rc

Three ZLP fixes on dwc3 and a resource leak fix on the TCM gadget
Signed-off-by: Felipe Balbi <balbi@kernel.org>

* tag 'fixes-for-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
  usb: dwc3: gadget: Handle ZLP for sg requests
  usb: dwc3: gadget: Fix handling ZLP
  usb: dwc3: gadget: Don't setup more than requested
  usb: gadget: f_tcm: Fix some resource leaks in some error paths

When a new device with a specialised device driver is plugged in, the
new driver will be modprobe()'d but the driver core will attach the
"generic" driver to the device.

After that, nothing will trigger a reprobe when the modprobe()'d device
driver has finished initialising, as the device has the "generic"
driver attached to it.

Trigger a reprobe ourselves when new specialised drivers get registered.

Fixes: 88b7381a ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-3-hadess@hadess.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We only ever used the ID table matching before, but we should also support
open-coded match functions.

Fixes: 88b7381a ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-1-hadess@hadess.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tegra_xusb_get_phy() should take input argument "name".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200811092553.657762-1-jckuo@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tegra_xusb_init_usb_phy() should initialize "otg_usb2_port" and
"otg_usb3_port" with -EINVAL because "0" is a valid value
represents usb2 port 0 or usb3 port 0.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200811093143.699541-1-jckuo@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On the removal stage we put a reference to the controller structure and
if it's not used anymore it gets freed, but later we try to dereference
a pointer to a member of that structure.

Copy necessary field to a temporary variable to avoid use after free.

Fixes: 306c54d0 ("usb: hcd: Try MSI interrupts on PCI devices")
Reported-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/linux-usb/30a8c4ca-64c2-863b-cfcd-0970599c0ba3@huawei.com/Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200814182218.71957-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 081da132 ("usb: typec: ucsi: displayport: Fix a potential race
during registration") made the ucsi code hold con->lock in
ucsi_register_displayport(). But we really don't want any interactions
with the connector to run before the port-registration process is fully
complete.

This commit moves the taking of con->lock from ucsi_register_displayport()
into ucsi_register_port() to achieve this.

Cc: stable@vger.kernel.org
Fixes: 081da132 ("usb: typec: ucsi: displayport: Fix a potential race during registration")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-5-hdegoede@redhat.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().

Push the taking of the lock down into these 2 functions, renaming
ucsi_run_command() to ucsi_send_command() which was an existing
wrapper already taking the lock for its callers.

This simplifies things for the callers and removes the difference
between ucsi_send_command() and ucsi_run_command() which has led
to various locking bugs in the past.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-4-hdegoede@redhat.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix 2 unlocked ucsi_run_command calls:

1. ucsi_handle_connector_change() contains one ucsi_send_command() call,
which takes the ppm_lock for it; and one ucsi_run_command() call which
relies on the caller have taking the ppm_lock.
ucsi_handle_connector_change() does not take the lock, so the
second (ucsi_run_command) calls should also be ucsi_send_command().

2. ucsi_get_pdos() gets called from ucsi_handle_connector_change() which
does not hold the ppm_lock, so it also must use ucsi_send_command().

This commit also adds a WARN_ON(!mutex_is_locked(&ucsi->ppm_lock)); to
ucsi_run_command() to avoid similar problems getting re-introduced in
the future.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-3-hdegoede@redhat.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Lockdep reports an AB BA lock inversion between ucsi_init() and
ucsi_handle_connector_change():

AB order:

1. ucsi_init takes ucsi->ppm_lock (it runs with that locked for the
   duration of the function)
2. usci_init eventually end up calling ucsi_register_displayport,
   which takes ucsi_connector->lock

BA order:

1. ucsi_handle_connector_change work is started, takes ucsi_connector->lock
2. ucsi_handle_connector_change calls ucsi_send_command which takes
   ucsi->ppm_lock

The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().

This commit fixes the AB BA lock inversion by making ucsi_init drop the
ucsi->ppm_lock before it starts registering ports; and replacing any
ucsi_run_command() calls after this point with ucsi_send_command()
(which is a wrapper around run_command taking the lock while handling
the command).

Some of the replacing of ucsi_run_command with ucsi_send_command
in the helpers used during port registration also fixes a number of
code paths after registration which call ucsi_run_command() without
holding the ppm_lock:
1. ucsi_altmode_update_active() call in ucsi/displayport.c
2. ucsi_register_altmodes() call from ucsi_handle_connector_change()
   (through ucsi_partner_change())

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-2-hdegoede@redhat.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 88b7381a ("USB: Select better matching USB drivers when
available") introduced the use of a "match" function to select a
non-generic/better driver for a particular USB device. This
unfortunately breaks the operation of usbip in general, as reported in
the kernel bugzilla with bug 208267 (linked below).

Upon inspecting the aforementioned commit, one can observe that the
original code in the usb_device_match function used to return 1
unconditionally, but the aforementioned commit makes the usb_device_match
function use identifier tables and "match" virtual functions, if either of
them are available.

Hence, this commit implements a match function for usbip that
unconditionally returns true to ensure that usbip is functional again.

This change has been verified to restore usbip functionality, with a
v5.7.y kernel on an up-to-date version of Qubes OS 4.0, which uses
usbip to redirect USB devices between VMs.

Thanks to Jonathan Dieter for the effort in bisecting this issue down
to the aforementioned commit.

Fixes: 88b7381a ("USB: Select better matching USB drivers when available")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208267
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1856443
Link: https://github.com/QubesOS/qubes-issues/issues/5905Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Cc: <stable@vger.kernel.org> # 5.7
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200810160017.46002-1-m.v.b@runbox.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some devices in wild are reporting bunch of firmware versions, so remove
the check for versions in driver

Reported by: Anastasios Vacharakis <vacharakis@gmail.com>
Reported by: Glen Journeay <journeay@gmail.com>
Fixes: 2478be82 ("usb: renesas-xhci: Add ROM loader for uPD720201")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=208911Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200818071739.789720-1-vkoul@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lvs_rh_probe() can return some nonnegative value from usb_control_msg()
when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as
a failure. Make lvs_rh_probe() return -EINVAL in this case.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200805090643.3432-1-novikov@ispras.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clang static analysis reports this error

cdc-acm.c:409:3: warning: Use of memory after it is freed
        acm_process_notification(acm, (unsigned char *)dr);

There are three problems, the first one is that dr is not reset

The variable dr is set with

if (acm->nb_index)
	dr = (struct usb_cdc_notification *)acm->notification_buffer;

But if the notification_buffer is too small it is resized with

		if (acm->nb_size) {
			kfree(acm->notification_buffer);
			acm->nb_size = 0;
		}
		alloc_size = roundup_pow_of_two(expected_size);
		/*
		 * kmalloc ensures a valid notification_buffer after a
		 * use of kfree in case the previous allocation was too
		 * small. Final freeing is done on disconnect.
		 */
		acm->notification_buffer =
			kmalloc(alloc_size, GFP_ATOMIC);

dr should point to the new acm->notification_buffer.

The second problem is any data in the notification_buffer is lost
when the pointer is freed.  In the normal case, the current data
is accumulated in the notification_buffer here.

	memcpy(&acm->notification_buffer[acm->nb_index],
	       urb->transfer_buffer, copy_size);

When a resize happens, anything before
notification_buffer[acm->nb_index] is garbage.

The third problem is the acm->nb_index is not reset on a
resizing buffer error.

So switch resizing to using krealloc and reassign dr and
reset nb_index.

Fixes: ea258352 ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200801152154.20683-1-trix@redhat.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There's another Raydium touchscreen needs the no-lpm quirk:
[    1.339149] usb 1-9: New USB device found, idVendor=2386, idProduct=350e, bcdDevice= 0.00
[    1.339150] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.339151] usb 1-9: Product: Raydium Touch System
[    1.339152] usb 1-9: Manufacturer: Raydium Corporation
...
[    6.450497] usb 1-9: can't set config #1, error -110

BugLink: https://bugs.launchpad.net/bugs/1889446Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200731051622.28643-1-kai.heng.feng@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The syzbot fuzzer identified a bug in the yurex driver: It passes
GFP_KERNEL as a memory-allocation flag to usb_submit_urb() at a time
when its state is TASK_INTERRUPTIBLE, not TASK_RUNNING:

do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000370c7c68>] prepare_to_wait+0xb1/0x2a0 kernel/sched/wait.c:247
WARNING: CPU: 1 PID: 340 at kernel/sched/core.c:7253 __might_sleep+0x135/0x190
kernel/sched/core.c:7253
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 340 Comm: syz-executor677 Not tainted 5.8.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xf6/0x16e lib/dump_stack.c:118
 panic+0x2aa/0x6e1 kernel/panic.c:231
 __warn.cold+0x20/0x50 kernel/panic.c:600
 report_bug+0x1bd/0x210 lib/bug.c:198
 handle_bug+0x41/0x80 arch/x86/kernel/traps.c:234
 exc_invalid_op+0x14/0x40 arch/x86/kernel/traps.c:254
 asm_exc_invalid_op+0x12/0x20 arch/x86/include/asm/idtentry.h:536
RIP: 0010:__might_sleep+0x135/0x190 kernel/sched/core.c:7253
Code: 65 48 8b 1c 25 40 ef 01 00 48 8d 7b 10 48 89 fe 48 c1 ee 03 80 3c 06 00 75
2b 48 8b 73 10 48 c7 c7 e0 9e 06 86 e8 ed 12 f6 ff <0f> 0b e9 46 ff ff ff e8 1f
b2 4b 00 e9 29 ff ff ff e8 15 b2 4b 00
RSP: 0018:ffff8881cdb77a28 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8881c6458000 RCX: 0000000000000000
RDX: ffff8881c6458000 RSI: ffffffff8129ec93 RDI: ffffed1039b6ef37
RBP: ffffffff86fdade2 R08: 0000000000000001 R09: ffff8881db32f54f
R10: 0000000000000000 R11: 0000000030343354 R12: 00000000000001f2
R13: 0000000000000000 R14: 0000000000000068 R15: ffffffff83c1b1aa
 slab_pre_alloc_hook.constprop.0+0xea/0x200 mm/slab.h:498
 slab_alloc_node mm/slub.c:2816 [inline]
 slab_alloc mm/slub.c:2900 [inline]
 kmem_cache_alloc_trace+0x46/0x220 mm/slub.c:2917
 kmalloc include/linux/slab.h:554 [inline]
 dummy_urb_enqueue+0x7a/0x880 drivers/usb/gadget/udc/dummy_hcd.c:1251
 usb_hcd_submit_urb+0x2b2/0x22d0 drivers/usb/core/hcd.c:1547
 usb_submit_urb+0xb4e/0x13e0 drivers/usb/core/urb.c:570
 yurex_write+0x3ea/0x820 drivers/usb/misc/yurex.c:495

This patch changes the call to use GFP_ATOMIC instead of GFP_KERNEL.

Reported-and-tested-by: syzbot+c2c3302f9c601a4b1be2@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810182954.GB307778@rowland.harvard.eduSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently dwc3 doesn't handle usb_request->zero for SG requests. This
change checks and prepares extra TRBs for the ZLP for SG requests.

Cc: <stable@vger.kernel.org> # v4.5+
Fixes: 04c03d10 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The usb_request->zero doesn't apply for isoc. Also, if we prepare a
0-length (ZLP) TRB for the OUT direction, we need to prepare an extra
TRB to pad up to the MPS alignment. Use the same bounce buffer for the
ZLP TRB and the extra pad TRB.

Cc: <stable@vger.kernel.org> # v4.5+
Fixes: d6e5a549 ("usb: dwc3: simplify ZLP handling")
Fixes: 04c03d10 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The SG list may be set up with entry size more than the requested
length. Check the usb_request->length and make sure that we don't setup
the TRBs to send/receive more than requested. This case may occur when
the SG entry is allocated up to a certain minimum size, but the request
length is less than that. It can also occur when the request is reused
for a different request length.

Cc: <stable@vger.kernel.org> # v4.18+
Fixes: a31e63b6 ("usb: dwc3: gadget: Correct handling of scattergather lists")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

If a memory allocation fails within a 'usb_ep_alloc_request()' call, the
already allocated memory must be released.

Fix a mix-up in the code and free the correct requests.

Fixes: c52661d6 ("usb-gadget: Initial merge of target module for UASP + BOT")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Pull io_uring fixes from Jens Axboe:
 "A few differerent things in here.

  Seems like syzbot got some more io_uring bits wired up, and we got a
  handful of reports and the associated fixes are in here.

  General fixes too, and a lot of them marked for stable.

  Lastly, a bit of fallout from the async buffered reads, where we now
  more easily trigger short reads. Some applications don't really like
  that, so the io_read() code now handles short reads internally, and
  got a cleanup along the way so that it's now easier to read (and
  documented). We're now passing tests that failed before"

* tag 'io_uring-5.9-2020-08-15' of git://git.kernel.dk/linux-block:
  io_uring: short circuit -EAGAIN for blocking read attempt
  io_uring: sanitize double poll handling
  io_uring: internally retry short reads
  io_uring: retain iov_iter state over io_read/io_write calls
  task_work: only grab task signal lock when needed
  io_uring: enable lookup of links holding inflight files
  io_uring: fail poll arm on queue proc failure
  io_uring: hold 'ctx' reference around task_work queue + execute
  fs: RWF_NOWAIT should imply IOCB_NOIO
  io_uring: defer file table grabbing request cleanup for locked requests
  io_uring: add missing REQ_F_COMP_LOCKED for nested requests
  io_uring: fix recursive completion locking on oveflow flush
  io_uring: use TWA_SIGNAL for task_work uncondtionally
  io_uring: account locked memory before potential error case
  io_uring: set ctx sq/cq entry count earlier
  io_uring: Fix NULL pointer dereference in loop_rw_iter()
  io_uring: add comments on how the async buffered read retry works
  io_uring: io_async_buf_func() need not test page bit

Commit 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one()
and pmd_free_one()") converted parisc to use generic version of
pmd_alloc_one() but it missed the fact that parisc uses order-1 pages for
PMD.

Restore the original version of pmd_alloc_one() for parisc, just use
GFP_PGTABLE_KERNEL that implies __GFP_ZERO instead of GFP_KERNEL and
memset.

Fixes: 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one() and pmd_free_one()")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lkml.kernel.org/r/9f2b5ebd-e4a4-0fa1-6cd3-4b9f6892d1ad@linux.eeSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block fixes from Jens Axboe:
 "A few fixes on the block side of things:

   - Discard granularity fix (Coly)

   - rnbd cleanups (Guoqing)

   - md error handling fix (Dan)

   - md sysfs fix (Junxiao)

   - Fix flush request accounting, which caused an IO slowdown for some
     configurations (Ming)

   - Properly propagate loop flag for partition scanning (Lennart)"

* tag 'block-5.9-2020-08-14' of git://git.kernel.dk/linux-block:
  block: fix double account of flush request's driver tag
  loop: unset GENHD_FL_NO_PART_SCAN on LOOP_CONFIGURE
  rnbd: no need to set bi_end_io in rnbd_bio_map_kern
  rnbd: remove rnbd_dev_submit_io
  md-cluster: Fix potential error pointer dereference in resize_bitmaps()
  block: check queue's limits.discard_granularity in __blkdev_issue_discard()
  md: get sysfs entry after redundancy attr group create

Pull RISC-V fix from Palmer Dabbelt:
 "I collected a single fix during the merge window: we managed to break
  the early trap setup on !MMU, this fixes it"

* tag 'riscv-for-linus-5.9-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Setup exception vector for nommu platform

Pull arch/sh updates from Rich Felker:
 "Cleanup, SECCOMP_FILTER support, message printing fixes, and other
  changes to arch/sh"

* tag 'sh-for-5.9' of git://git.libc.org/linux-sh: (34 commits)
  sh: landisk: Add missing initialization of sh_io_port_base
  sh: bring syscall_set_return_value in line with other architectures
  sh: Add SECCOMP_FILTER
  sh: Rearrange blocks in entry-common.S
  sh: switch to copy_thread_tls()
  sh: use the generic dma coherent remap allocator
  sh: don't allow non-coherent DMA for NOMMU
  dma-mapping: consolidate the NO_DMA definition in kernel/dma/Kconfig
  sh: unexport register_trapped_io and match_trapped_io_handler
  sh: don't include <asm/io_trapped.h> in <asm/io.h>
  sh: move the ioremap implementation out of line
  sh: move ioremap_fixed details out of <asm/io.h>
  sh: remove __KERNEL__ ifdefs from non-UAPI headers
  sh: sort the selects for SUPERH alphabetically
  sh: remove -Werror from Makefiles
  sh: Replace HTTP links with HTTPS ones
  arch/sh/configs: remove obsolete CONFIG_SOC_CAMERA*
  sh: stacktrace: Remove stacktrace_ops.stack()
  sh: machvec: Modernize printing of kernel messages
  sh: pci: Modernize printing of kernel messages
  ...

One case was missed in the short IO retry handling, and that's hitting
-EAGAIN on a blocking attempt read (eg from io-wq context). This is a
problem on sockets that are marked as non-blocking when created, they
don't carry any REQ_F_NOWAIT information to help us terminate them
instead of perpetually retrying.

Fixes: 227c0c96 ("io_uring: internally retry short reads")
Signed-off-by: Jens Axboe <axboe@kernel.dk>

There's a bit of confusion on the matching pairs of poll vs double poll,
depending on if the request is a pure poll (IORING_OP_POLL_ADD) or
poll driven retry.

Add io_poll_get_double() that returns the double poll waitqueue, if any,
and io_poll_get_single() that returns the original poll waitqueue. With
that, remove the argument to io_poll_remove_double().

Finally ensure that wait->private is cleared once the double poll handler
has run, so that remove knows it's already been seen.

Cc: stable@vger.kernel.org # v5.8
Reported-by: syzbot+7f617d4a9369028b8a2c@syzkaller.appspotmail.com
Fixes: 18bceab1 ("io_uring: allow POLL_ADD with double poll_wait() users")
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull more perf tools updates from Arnaldo Carvalho de Melo:
 "Fixes:
   - Fixes for 'perf bench numa'.

   - Always memset source before memcpy in 'perf bench mem'.

   - Quote CC and CXX for their arguments to fix build in environments
     using those variables to pass more than just the compiler names.

   - Fix module symbol processing, addressing regression detected via
     "perf test".

   - Allow multiple probes in record+script_probe_vfs_getname.sh 'perf
     test' entry.

  Improvements:
   - Add script to autogenerate socket family name id->string table from
     copy of kernel header, used so far in 'perf trace'.

   - 'perf ftrace' improvements to provide similar options for this
     utility so that one can go from 'perf record', 'perf trace', etc to
     'perf ftrace' just by changing the name of the subcommand.

   - Prefer new "sched:sched_waking" trace event when it exists in 'perf
     sched' post processing.

   - Update POWER9 metrics to utilize other metrics.

   - Fall back to querying debuginfod if debuginfo not found locally.

  Miscellaneous:
   - Sync various kvm headers with kernel sources"

* tag 'perf-tools-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (40 commits)
  perf ftrace: Make option description initials all capital letters
  perf build-ids: Fall back to debuginfod query if debuginfo not found
  perf bench numa: Remove dead code in parse_nodes_opt()
  perf stat: Update POWER9 metrics to utilize other metrics
  perf ftrace: Add change log
  perf: ftrace: Add set_tracing_options() to set all trace options
  perf ftrace: Add option --tid to filter by thread id
  perf ftrace: Add option -D/--delay to delay tracing
  perf: ftrace: Allow set graph depth by '--graph-opts'
  perf ftrace: Add support for trace option tracing_thresh
  perf ftrace: Add option 'verbose' to show more info for graph tracer
  perf ftrace: Add support for tracing option 'irq-info'
  perf ftrace: Add support for trace option funcgraph-irqs
  perf ftrace: Add support for trace option sleep-time
  perf ftrace: Add support for tracing option 'func_stack_trace'
  perf tools: Add general function to parse sublevel options
  perf ftrace: Add option '--inherit' to trace children processes
  perf ftrace: Show trace column header
  perf ftrace: Add option '-m/--buffer-size' to set per-cpu buffer size
  perf ftrace: Factor out function write_tracing_file_int()
  ...

Pull x86 fixes from Ingo Molnar:
 "Misc fixes and small updates all around the place:

   - Fix mitigation state sysfs output

   - Fix an FPU xstate/sxave code assumption bug triggered by
     Architectural LBR support

   - Fix Lightning Mountain SoC TSC frequency enumeration bug

   - Fix kexec debug output

   - Fix kexec memory range assumption bug

   - Fix a boundary condition in the crash kernel code

   - Optimize porgatory.ro generation a bit

   - Enable ACRN guests to use X2APIC mode

   - Reduce a __text_poke() IRQs-off critical section for the benefit of
     PREEMPT_RT"

* tag 'x86-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/alternatives: Acquire pte lock with interrupts enabled
  x86/bugs/multihit: Fix mitigation reporting when VMX is not in use
  x86/fpu/xstate: Fix an xstate size check warning with architectural LBRs
  x86/purgatory: Don't generate debug info for purgatory.ro
  x86/tsr: Fix tsc frequency enumeration bug on Lightning Mountain SoC
  kexec_file: Correctly output debugging information for the PT_LOAD ELF header
  kexec: Improve & fix crash_exclude_mem_range() to handle overlapping ranges
  x86/crash: Correct the address boundary of function parameters
  x86/acrn: Remove redundant chars from ACRN signature
  x86/acrn: Allow ACRN guest to use X2APIC mode

Pull scheduler fixes from Ingo Molnar:
 "Two fixes: fix a new tracepoint's output value, and fix the formatting
  of show-state syslog printouts"

* tag 'sched-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix the alignment of the show-state debug output
  sched: Fix use of count for nr_running tracepoint