The Banana Pi M2 Ultra is an SBC based on the Allwinner V40 SoC (same as
the R40 SoC). The form factor is similar to the Raspberry Pi series.

It features:

- X-Powers AXP221s PMIC connected to i2c0
- 1GiB DDR3 DRAM
- microSD slot
- MicroUSB Type-B port for power and connected to usb0
- HDMI output
- MIPI DSI connector
- 4 USB Type-A ports (connected to the usb1 controller via a hub)
- gigabit ethernet with Realtek RTL8211E transceiver
- WiFi/Bluetooth with AP6212 module, with external antenna connector
- SATA and power connectors for native SATA support
- camera sensor connector
- audio out headphone jack
- red and green LEDs
- debug UART pins
- Raspberry Pi B+ compatible GPIO header
- power and reset buttons

This patch adds a dts file that enables UART, MMC and PMIC support.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Banana Pi M2 Ultra is an SBC based on the Allwinner R40 SoC. The
form factor and position of various connectors, leds and buttons is
similar to the Banana Pi M1+, Banana Pi M3, and is exactly the same
as the latest Banana Pi M64.

It features:

  - X-Powers AXP221s PMIC connected to i2c0
  - 2 GB DDR3 DRAM
  - 8 GB eMMC
  - micro SD card slot
  - DC power jack
  - HDMI output
  - MIPI DSI connector
  - 2x USB 2.0 hosts
  - 1x USB 2.0 OTG
  - gigabit ethernet with Realtek RTL8211E transceiver
  - WiFi/Bluetooth with AP6212 chip, with external antenna connector
  - SATA and power connectors for native SATA support
  - camera sensor connector
  - consumer IR receiver
  - audio out headphone jack
  - onboard microphone
  - red, green, and blue LEDs
  - debug UART pins
  - Li-Po battery connector
  - Raspberry Pi B+ compatible GPIO header
  - power, reset, and boot control buttons

This patch adds a dts file that enables UART, MMC and PMIC support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner R40 SoC is marketed as the successor to the A20 SoC.
The R40 is a smaller chip than the A20, but features the same set
of programmable pins, with a couple extra pins and some new pin
functions. The chip features 4 Cortex-A7 cores and a Mali-400 MP2
GPU. It retains most if not all features from the A20, while adding
some new features, such as MIPI DSI output, or updating various
hardware blocks, such as DE 2.0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch remove leading 0 of unit address and so remove
lots of warning when building DT with W=1.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

This patch fixes the warning "xxx has a unit name, but no reg property"
by removing "@0" from such node. 6 board files are fixed. Each has the
same aforementioned issue in pinmux nodes. These include the Nano Pi
family base dtsi file, the Orange Pi 2, Orange Pi Lite, Orange Pi One,
Orange Pi PC, and Orange Pi Plus.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Squashed 6 patches together; boards named in commit log]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

This patch fix the warning "xxx has a unit name, but no reg property" by
removing "@0" from such node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The unit address and register address does not match.
This patch fix the register address with the good one.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

This patch remove leading 0 of unit address and so remove
lots of warning when building DT with W=1.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Lamobo R1 board connected the ACIN of the AXP209 PMIC to a MicroUSB
port, and the battery input is connected to a generic connector.

Enable these two power supplies in the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The TCONs on A31/A31s can select either backend as its input. As there
is no configurable mux in the backend or DRC to redirect their output,
or for the DRC to select an input, the connections are presumably from
the each DRC to each TCON, with the TCON having two input ports, like
the following diagram:

	Backend 0  -------  DRC 0  ------- [0]  TCON 0
				   --   -- [1]
                                     \ /
				      X
				     / \
				   --   -- [0]
	Backend 1  -------  DRC 1  ------- [1]  TCON 1

Add these connection endpoints to the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

There is no need for pincontrol nodes when the pin is set to a GPIO
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the new DAI blocks to the device tree. I2S0 and I2S1 are for
connecting to an external codec.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The WiFi side of the AP6212 WiFi/BT combo module is connected to
mmc1. There are also GPIOs for enable and interrupts.

Enable WiFi on this board by enabling mmc1 and adding the power
sequencing clocks and GPIO, as well as the chip's interrupt line.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The TBS A711 is a tablet with an A83T, a modem, wifi/BT chip, an eMMC and a
1024x600 LVDS display.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

sun4i-a10.dtsi was missing i2s0 block. Add it.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the new DAI blocks to the device tree.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T has an UART1 controller, with the RTS and CTS pins routed so it
can be used for devices with hardware flow control, like a bluetooth chip.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the pinctrl definitions for the A83t MMC1 controller.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Those nodes are useless, remove them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

TBS is a company providing biometrics products and solution in Access
control and time management.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.

This patch is compatible with earlier board revisions, since this
pin wasn't connected to phy.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The BT side of the AP6212 WiFi/BT combo module is connected to
uart3.

Enable BT on this board by enabling uart3 with using additionally
the cts and rts pins.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This node adds the definition for the UART3 RTS and CTS Pins

That makes it able to use UART3 with RTS and CTS.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Nanopi M1 Plus has an onboard IR receiver.
This enables the onboard IR receiver subnode.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Nanopi M1 has an onboard IR receiver.
This enables the onboard IR receiver subnode.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The axp209.dtsi defines nodes for ac, usb and battery supplies for a
while now. This patch enables these nodes for the A20-Olinuxino-Micro,
which has connectors for all three of them.

The patch was run-tested against linux-next-20170825.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A20-OLinuXino-MICRO has option with onboard eMMC chip. For
now it's only shipped with 4BG chip, but in the future this
may change.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Convert sun4i-a10.dtsi to new CCU driver.

Tested on Gemei G9 tablet.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Convert sun7i-a20.dtsi to new CCU driver.

Tested on Cubietruck.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

When the second display pipeline device nodes for the A31/A31s were
added, it was not known that the TCONs could (through either DRCs)
select either backend as their input. Thus in the endpoints connecting
these components together, the endpoint IDs were set to 0, while in
fact they should have been set to 1.

Cc: <stable@vger.kernel.org>
Fixes: 9a26882a ("ARM: dts: sun6i: Add second display pipeline device
		      nodes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Since current tree support AXP803 regulators, replace
fixed regulator with AXP803 dcdc1 regulator.

Tested on pine64.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Pull UBI updates from Richard Weinberger:
 "Minor improvements"

* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
  UBI: Fix two typos in comments
  ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines

Pull UML updates from Richard Weinberger:

 - minor improvements

 - fixes for Debian's new gcc defaults (pie enabled by default)

 - fixes for XSTATE/XSAVE to make UML work again on modern systems

* 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: return negative in tuntap_open_tramp()
  um: remove a stray tab
  um: Use relative modversions with LD_SCRIPT_DYN
  um: link vmlinux with -no-pie
  um: Fix CONFIG_GCOV for modules.
  Fix minor typos and grammar in UML start_up help
  um: defconfig: Cleanup from old Kconfig options
  um: Fix FP register size for XSTATE/XSAVE

Pull networking fixes from David Miller:

 1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger.

 2) Fix double-free in rmnet driver, from Dan Carpenter.

 3) INET connection socket layer can double put request sockets, fix
    from Eric Dumazet.

 4) Don't match collect metadata-mode tunnels if the device is down,
    from Haishuang Yan.

 5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in
    be2net driver, from Suresh Reddy.

 6) Fix scaling error in gen_estimator, from Eric Dumazet.

 7) Fix 64-bit statistics deadlock in systemport driver, from Florian
    Fainelli.

 8) Fix use-after-free in sctp_sock_dump, from Xin Long.

 9) Reject invalid BPF_END instructions in verifier, from Edward Cree.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
  Documentation: link in networking docs
  tcp: fix data delivery rate
  bpf/verifier: reject BPF_ALU64|BPF_END
  sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
  sctp: fix an use-after-free issue in sctp_sock_dump
  netvsc: increase default receive buffer size
  tcp: update skb->skb_mstamp more carefully
  net: ipv4: fix l3slave check for index returned in IP_PKTINFO
  net: smsc911x: Quieten netif during suspend
  net: systemport: Fix 64-bit stats deadlock
  net: vrf: avoid gcc-4.6 warning
  qed: remove unnecessary call to memset
  tg3: clean up redundant initialization of tnapi
  tls: make tls_sw_free_resources static
  sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
  MAINTAINERS: review Renesas DT bindings as well
  net_sched: gen_estimator: fix scaling error in bytes/packets samples
  nfp: wait for the NSP resource to appear on boot
  nfp: wait for board state before talking to the NSP
  ...

Pull more input updates from Dmitry Torokhov:
 "A second round of updates for the input subsystem:

   - a new driver for PWM-controlled vibrators

   - ucb1400 touchscreen driver had completely busted suspend/resume
     handling

   - we now handle "home" button found on some devices with Goodix
     touchscreens

   - assorted other fixups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - add Gigabyte P57 to the keyboard reset table
  Input: xpad - validate USB endpoint type during probe
  Input: ucb1400_ts - fix suspend and resume handling
  Input: edt-ft5x06 - fix access to non-existing register
  Input: elantech - make arrays debounce_packet static, reduces object code size
  Input: surface3_spi - make const array header static, reduces object code size
  Input: goodix - add support for capacitive home button
  Input: add a driver for PWM controllable vibrators
  Input: adi - make array seq static, reduces object code size

Commit 5620a0d1 ("firmware: delete in-kernel firmware") removed the
entire firmware directory.  Unfortunately it thereby also removed the
support for built-in firmware.

This restores the ability to build firmware directly into the kernel by
pruning the original Makefile to the necessary minimum.  The default for
EXTRA_FIRMWARE_DIR is now the standard directory /lib/firmware/.

Fixes: 5620a0d1 ("firmware: delete in-kernel firmware")
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: Greg K-H <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.

This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.

Fixes: 65e65ec1 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Andreas Rammhold <andreas@rammhold.de>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix link in filter.txt.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now skb->mstamp_skb is updated later, we also need to call
tcp_rate_skb_sent() after the update is done.

Fixes: 8c72c65b ("tcp: update skb->skb_mstamp more carefully")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>