- 27 Jul, 2010 35 commits
-
-
Sarang Radke authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Giridhar Malavali authored
Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Andrew Vasquez authored
* hold the hardware_lock throughout the duration of ctx-sp timeout handling -- could result in use-after-free oops. * retry a timed-out login-request. * done() routines are called with the hardware-lock held, issue qla2x00_mark_device_lost() with proper 'defer' flag. * FCP2 capabilities are only relevant to target devices. Signed-off-by:
-
Giridhar Malavali authored
Hold a reference to the srb (sp) while aborting an I/O -- as the I/O can/will complete from within the interrupt-context. Signed-off-by:
-
Giridhar Malavali authored
The TMFs used for pre-24xx ISPs incorrectly assumed 'cpu' tag data could be valid. These chips have no multi-q/cpu-affinity support. This corrects an oops seen on ISP23xx parts. Signed-off-by:
-
Andrew Vasquez authored
This helps to correlate submission/completion messages during triaging. Signed-off-by:
-
Giridhar Malavali authored
The CRB drive active register is cleared when driver is unloaded or when driver enters failed state. Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
-
Stephen M. Cameron authored
We have 32 (MAXSGENTRIES) scatter gather elements embedded in the command. With all these, the total command size is about 576 bytes. However, the last entry in the block fetch table is 35. (the block fetch table contains the number of 16-byte chunks the firmware needs to fetch for a given number of scatter gather elements.) 35 * 16 = 560 bytes, which isn't enough. It needs to be 36. (36 * 16 == 576) or, MAXSGENTRIES + 4. (plus 4 because there's a bunch of stuff at the front of the command before the first scatter gather element that takes up 4 * 16 bytes.) Without this fix, the controller may have to perform two DMA operations to fetch the command since the first one may not get the whole thing. Signed-off-by:
Don Brace <brace@beardog.cce.hp.com> Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
before trying to enter simple mode transport method. Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
and delete duplicated comment Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Julia Lawall authored
The end of the function is reachable both when host is and is not NULL. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r exists@ expression E,E1; identifier f; statement S1,S2,S3; @@ if ((E == NULL && ...) || ...) { ... when != if (...) S1 else S2 when != E = E1 * E->f ... when any return ...; } else S3 // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Ryan Kuester authored
I may have an explanation for the LSI 1068 HBA hangs provoked by ATA pass-through commands, in particular by smartctl. First, my version of the symptoms. On an LSI SAS1068E B3 HBA running 01.29.00.00 firmware, with SATA disks, and with smartd running, I'm seeing occasional task, bus, and host resets, some of which lead to hard faults of the HBA requiring a reboot. Abusively looping the smartctl command, # while true; do smartctl -a /dev/sdb > /dev/null; done dramatically increases the frequency of these failures to nearly one per minute. A high IO load through the HBA while looping smartctl seems to improve the chance of a full scsi host reset or a non-recoverable hang. I reduced what smartctl was doing down to a simple test case which causes the hang with a single IO when pointed at the sd interface. See the code at the bottom of this e-mail. It uses an SG_IO ioctl to issue a single pass-through ATA identify device command. If the buffer userspace gives for the read data has certain alignments, the task is issued to the HBA but the HBA fails to respond. If run against the sg interface, neither the test code nor smartctl causes a hang. sd and sg handle the SG_IO ioctl slightly differently. Unless you specifically set a flag to do direct IO, sg passes a buffer of its own, which is page-aligned, to the block layer and later copies the result into the userspace buffer regardless of its alignment. sd, on the other hand, always does direct IO unless the userspace buffer fails an alignment test at block/blk-map.c line 57, in which case a page-aligned buffer is created and used for the transfer. The alignment test currently checks for word-alignment, the default setup by scsi_lib.c; therefore, userspace buffers of almost any alignment are given directly to the HBA as DMA targets. The LSI 1068 hardware doesn't seem to like at least a couple of the alignments which cross a page boundary (see the test code below). Curiously, many page-boundary-crossing alignments do work just fine. So, either the hardware has an bug handling certain alignments or the hardware has a stricter alignment requirement than the driver is advertising. If stricter alignment is required, then in no case should misaligned buffers from userspace be allowed through without being bounced or at least causing an error to be returned. It seems the mptsas driver could use blk_queue_dma_alignment() to advertise a stricter alignment requirement. If it does, sd does the right thing and bounces misaligned buffers (see block/blk-map.c line 57). The following patch to 2.6.34-rc5 makes my symptoms go away. I'm sure this is the wrong place for this code, but it gets my idea across. Acked-by:"Desai, Kashyap" <Kashyap.Desai@lsi.com> Signed-off-by:
-
Eric Moore authored
Adding DIF Type 2 protection support, as well as turning on 32 byte cdb's, and setting the cdb length for > 16 byte in the SCSI_IO->control parameter. Signed-off-by:
Martin Petersen <martin.petersen@oracle.com> Signed-off-by:
Eric Moore <eric.moore@lsi.com> Signed-off-by:
-
Anton Blanchard authored
A driver needs to be ready to take an interrupt as soon as it registers an interrupt handler. I noticed the following oops when testing kdump: ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010) ibmvscsi 30000002: SRP_VERSION: 16.a ibmvscsi 30000002: SRP_VERSION: 16.a Unable to handle kernel paging request for data at address 0x00000000 ... pc: c000000004085e34: .tasklet_action+0xf4/0x1dc ... c000000004086fe4 .__do_softirq+0x16c/0x2c0 c00000000403138c .call_do_softirq+0x14/0x24 c00000000400ee14 .do_softirq+0xa0/0x104 c00000000408690c .irq_exit+0x70/0xd0 c00000000400f190 .do_IRQ+0x214/0x2a8 c000000004004804 hardware_interrupt_entry+0x1c/0x98 --- Exception: 501 (Hardware Interrupt) at c00000000400c544 .raw_local_irq_restore+0x48/0x54 c00000000465d2a8 ._raw_spin_unlock_irqrestore+0x74/0xa0 c0000000040e7f00 .__setup_irq+0x2ec/0x3f0 c0000000040e8198 .request_threaded_irq+0x194/0x22c c00000000446d854 .rpavscsi_init_crq_queue+0x284/0x3f0 c00000000446c764 .ibmvscsi_probe+0x688/0x710 c00000000402903c .vio_bus_probe+0x37c/0x3e4 c000000004403f10 .driver_probe_device+0xec/0x1b8 c000000004404088 .__driver_attach+0xac/0xf4 c000000004403184 .bus_for_each_dev+0x98/0x104 c000000004403c98 .driver_attach+0x40/0x60 c0000000044026f0 .bus_add_driver+0x154/0x324 c0000000044045d0 .driver_register+0xe8/0x1ac c00000000402b2a8 .vio_register_driver+0x54/0x74 c000000004933ea4 .ibmvscsi_module_init+0x80/0xc0 c000000004009834 .do_one_initcall+0x98/0x1d8 c0000000049005b4 .kernel_init+0x27c/0x33c c000000004031550 .kernel_thread+0x54/0x70 srp_task needs to be setup before request_irq. The patch below fixes the oops. Signed-off-by:
Anton Blanchard <anton@samba.org> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
- 21 Jul, 2010 4 commits
-
-
Christof Schmitt authored
Commit 64deb6ef changed the way status read buffers are handled but forgot to adjust the mempool to the new size. Add the call to resize the mempool after the exchange config data. Also use the define instead of the hard coded number in the fsf callback for consistency. Reviewed-by:
Swen Schillig <swen@vnet.ibm.com> Signed-off-by:
Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by:
-
Christof Schmitt authored
Trying to read the FC host statistics on an offline adapter results in a 5 seconds wait. Reading the statistics tries to issue an exchange port data request which first waits up to 5 seconds for an entry in the request queue. Change the strategy for getting a free SBAL to exit when the queue is stopped. Reading the statistics will then fail without the wait. Reviewed-by:
-
Swen Schillig authored
A false check was performed whether an unchained ct_els is possible or not. Signed-off-by:
-
Wayne Boyer authored
It was possible to overflow the buffer used to print out the formatted version of the resource path. The fix is to limit the number of bytes that get formatted. This patch also updates the ipr_show_resource_path function to display the resource address for devices that are attached to adapters that don't support resource paths. Signed-off-by:
Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by:
-
- 12 Jun, 2010 1 commit
-
-
Linus Torvalds authored
-
