Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to
cap the maximum TX power value per-rate in the TX descriptor path.
Cap TX power for self generated frames (ACK, RTS/CTS).
Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the driver has sent a join iovar to the firmware it waits
for the events to report result of the connection. However, the
wpa_supplicant will request a .disconnect() after a timeout. So
upon calling .disconnect() the interface state may still be
CONNECTING. Clear the CONNECTING bit as well.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the Makefile for this driver, the wrong Kconfig option is used
to trigger the compilation of the object file. This leads to the
driver only being included into the kernel when both CONFIG_RTL8821AE
and CONFIG_RTL8192AE are set to "y".
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In four of the rtlwifi drivers, the Makefile contains superfluous
statements indicating the compilation of the driver as an LKM
regardless of the corresponding Kconfig option.

If the corresponding option is set to 'y', the build system will then
see the object file in obj-m and obj-y, which leads to a compilation
as a built-in only. Even though this leads to the desired behavior,
the unconditional appearance in obj-m is confusing for someone reading
the Makefile.

This patch removes the superfluous Makefile statements.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For FCC and JP, in one of the radar patterns, PPB and PRF seems to be
interchanged leading to frequent incorrect radar detections.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The usb gadget driver net2280 has exported a header file with the
register definition of the net2280 chip.

Remove the custom/duplicated header file in favor of that header file
in include/linux
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reconfigure RCR register in rtl_op_configure_filter() in order to apply RX
filter configuration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch fixes a static checker warning:

   drivers/net/wireless/brcm80211/brcmfmac/cfg80211.c:2965
      brcmf_cfg80211_set_pmksa()
	warn: can 'pmkid_len' be negative?

The answer to the question above is likely no so changing its
type to unsigned is sufficient.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'iwlwifi-next-for-john-2014-11-24' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Emmanuel Grumbach <egrumbach@gmail.com> says:

"Major works are CSA and TDLS. On top of that I have a new
firmware API for scan and a few rate control improvements.
Johannes find a few tricks to improve our CPU utilization
and adds support for a new spin of 7265 called 7265D.
Along with this a few random things that don't stand out."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also update the timeout for the data verification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new SDIO card id intended for the new 4165 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of channel switch, we need to teardown the TDLS peers.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver knows whether an rx frame was beamformed and marks
it in the radiotap VHT flags. However it should also declare
that it knows to extract this info otherwise this gets discarded
by sniffers like Wireshark.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support to MFUART loading notification (print notification
data with IWL_DEBUG_INFO)
Signed-off-by: Chaya Rachel Ivgy <chaya.rachel.ivgi@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

call the appropriate iwl_trans_suspend/resume ops
on iwl_mvm_suspend/resume calls.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add suspend/resume trans ops that will be called from
mac80211's suspend/resume ops.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When the device wakes up due to netdetect, we need to query different
things from the firmware than when it wakes up with a normal WoWLAN.
To make this easier, separate the netdetect wake up handling from the
rest.  For now, we don't send netdetect as a wake up reason, treating
it as a non-wireless wake up.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Refactor the iwl_mvm_query_wakeup_reasons() function to split the part
that gets the firmware status from the part that sets up the WoWLAN
status.  This will allow netdetect to reuse the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We need to send a WOWLAN_CONFIGURATION command also for netdetect and
configure the rfkill release trigger if needed.  To do so, refactor
the code that configures wowlan and netdetect when suspending and send
the WOWLAN_CONFIGURATION command also for net_detect.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add the net detect WoWLAN flag to indicate support and use the
nd_config from the WoWLAN configuration to start net detect, if it is
set.  The WoWLAN configuration takes precedence over the debugfs
configuration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When another vif is also running during a channel switch, we need to
use a session protection when we move to the new channel, so that we
don't miss the beacons.  Without this, sometimes the other vif
repeatedly gets time exactly when we should be hearing the beacons,
preventing channel switch from completing.  Adding a session
protection that lasts from the moment the channel changes until 2
TBTTs later, ensures that we will hear the beacons on the destination
channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

If setting the CSA time event fails, we must clear the TE data,
otherwise we'll try to remove it when, for instance, a disconnection
occurs, causing a SYSASSERT.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

After a channel switch, transmission on the new channel is only
started once we see a beacon on it.  Thus, beacon filtering needs to
be disabled during channel switch so that mac80211 receives this
beacon and finishes the process.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

We need to call ieee80211_chswitch_done() ourselves just when the
absence TE started, so we perform the actual context switch early
enough.  To do so, add a dummy channel_switch op, which will cause
mac80211 to skip the countdown timer and allow us to call
ieee80211_chswitch_done() to complete the operation.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

Now that mac80211 waits for the first beacon on the new channel before
calling post_channel_switch, the reconfiguration of the firmware
should be done in the post_channel_switch operation instead of when
assigning the vif to the new context.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

Instead of using a hardcoded number of TUs before beacon 0 as the time
to start the absence and actual channel switch, calculate it in
relation to the beacon interval.  We use 10 TUs + beacon interval
before beacon 0 to target a bit before beacon 1.  This gives us enough
time to switch to the new channel before the AP/GO switches.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

Add an absent time event when pre_channel_switch is called and use the
time event started indication to set the disable_tx bit instead of
doing it in unassign_vif().  This is done so that the firmware queues
are stopped before the actual switch takes place to avoid losing
packets while the AP/GO is performing its actual switch.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

Now that all CSA flows are using the switch_vif_chanctx op, we can
rely on the switching_chanctx boolean that is passed to the
__iwl_mvm_assign_vif_chanctx() and __iwl_mvm_unassign_vif_chanctx()
functions to decide whether the context switch flows need to be
executed.  In this way we make the chanctx switch flow more generic,
without having to rely on the csa_active flag being set.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

Disable PS when pre_channel_switch is called and add the
post_channel_switch operation to re-enable PS when the channel switch
is completed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

The spec requires to decrement the CSA counters based on TBTT,
regardless if the beacon was actually transmitted. Previously, the fw
would send beacon notifications only for successfully transmitted
beacons. This behavior resulted in inaccurate CSA countdown. In order
to address this issue, the fw was changed to send beacon
notifications also for not transmitted beacons. Such notifications
have TX_STATUS_INTERNAL_ABORT (0x92).
Don't start the CSA countdown before first successfully transmitted
beacon, in order to guarantee that the CSA is announced for a
required period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>

We have code to recover and go back to the original channel context if
something fails in the middle of switch_vif_chanctx, but we return the
error code of the recover calls instead of the original code, so if
the recovery succeeds, we will return 0 (success).  Fix this by not
assigning the return value of the recovery calls to ret.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

Add support to reassign vif in switch_vif_chanctx.  This is similar to
the existing CHANCTX_SWMODE_SWAP_CONTEXTS mode, but doesn't delete the
old context nor creates a new one, doing to switch between two
existing contexts.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

Currently we only support the CHANCTX_SWMODE_SWAP_CONTEXTS mode, but
we need to support other modes as well.  Spin a new function off in
order to make it easier to support other modes.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

We only need the csa_vif in AP/GO modes, and assigning for other
interfaces may cause problems, because csa_vif is never cleared.  To
prevent this, only assign the value if the iftype is
NL80211_IFTYPE_AP.  Use a switch to do this, even though, for now,
only the AP interface type is handled, because soon other interface
types will be added as well.

Additionally, convert the WARN() in the error case when a
channel-switch is already running to WARN_ONCE().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

A new callback has been added to prepare the device for a channel
switch.  Use the new callback instead of the old channel_switch_beacon
operation.

This makes it possible to remove the channel_switch_beacon operation
from mac80211.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

Maintain a TDLS channel-switch state and update it according to
notifications from FW and timeouts. Explicitly check all state
transitions are valid.
When switching is initiated by mac80211, use a delayed work to
periodically reschedule it from iwlwifi.
Give the FW mac80211 generated TDLS channel-switch request/response
templates. It will change appropriate values (switch timings) and Tx
them at appropriate times.

Enable the channel switch wiphy capability bit when the FW supports it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Block TID 4 (VI) on a vif when using TDLS. This TID will be used by FW
for TDLS channel-switch requests and PTI requests.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When adding a TDLS station, allocate 4 new queues for it. Configure them
to FW and enable them. On station removal, drain the queues if needed
and disable them when empty.

Make sure to flush all packets in the private queues of TDLS stations in
the mac80211 flush() callback.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When TDLS peers are present the FW will send packets on a dedicated
TID vs. the peer when performing TDLS channel-switches. The driver
configures the TID on connection to the peer and the FW is responsible
for maintaining the state of QoS seqno and PN/IV for encryption.

If the FW asserts, the driver cannot correctly reconfigure the starting
seqno/PN to the reloaded FW, thus forcing us to reconnect the peer.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>