This sends new notifications to the monitor support whenever a
management channel has been opened or closed. This allows tracing of
control channels really easily.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The mgmt version information will be also needed for the control
changell tracing feature. This provides a helper to pack them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

To further allow unique identification and tracking of control socket,
store cookie and comm information when binding the socket.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The SOL_HCI level should be enforced when using socket options on the
HCI raw socket interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Device 0cf3:e009 is one of the QCA ROME family.

T:  Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e009 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Commit 5177a838 ("Bluetooth: Add debugfs fields for hardware and
firmware info") introduced hci_set_hw_info() and hci_set_fw_info().
These functions use kvasprintf_const() but are not marked with a
__printf attribute.  Adding such an attribute helps detecting issues
related to printf-formatting at build time.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

wait_on_bit_timeout() returns one of the following three values:
* 0 to indicate success.
* -EINTR to indicate that a signal has been received;
* -EAGAIN to indicate timeout;
Make the wait_on_bit_timeout() callers check for these values.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Qualcomm WCNSS chip provides two SMD channels to the BT core; one
for command and one for event packets. This driver exposes the two
channels as a hci device.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch assigns the next free HCI device identifier to Bluetooth
devices based on the Qualcomm Shared Memory channels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Just because we don't support certain types of frames yet doesn't mean
we have to flood the message log with warnings about "invalid" frames.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes handling to remove short address for a neigbour entry
if RS/RA/NS/NA doesn't contain a short address. If these messages
doesn't has any short address option, the existing short address from
ndisc cache will be used. The current behaviour will set that the
neigbour doesn't has a short address anymore.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch sets the net namespace when creating SoftMAC interfaces. This
is important if the namespace at phy layer was switched before.
Currently we losing interfaces in some namespace and it's not possible
to recover that.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Instead of just having a LED trigger for power on a specific controller,
this adds the LED trigger "bluetooth-power" that combines the power
states of all controllers into a single trigger. This simplifies the
trigger selection and also supports multiple controllers per host
system via a single LED.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The led_trigger field in hci_dev should be conditional based on if
CONFIG_BT_LEDS is set or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Merge tag 'rxrpc-rewrite-20160917-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Tracepoint addition and improvement

Here is a set of patches that add some more tracepoints and improve a couple
of existing ones.  New additions include:

 (1) Connection refcount tracking.

 (2) Client connection state machine tracking.

 (3) Tx and Rx packet lifecycle.

 (4) ACK reception and transmission.

 (5) recvmsg processing.

Updates include:

 (1) Print the symbolic packet name in the Rx packet tracepoint.

 (2) Additional call refcount trace events.

 (3) Improvements to sk_buff tracking with AF_RXRPC.

In addition:

 (1) Config option to inject packet loss during both transmission and
     reception.

 (2) Removal of some printks.

This series needs to be applied on top of the previously posted fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160917-1' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Fixes & miscellany

Here are some more AF_RXRPC fix patches with a couple of miscellaneous
changes also.  Fixes include:

 (1) Make RxRPC IPv6 support conditional on IPv6 being available.

 (2) Move the condition check in rxrpc_locate_data() into the caller and
     check the error return.

 (3) Fix the detection of the last received packet in recvmsg.

 (4) Account calls that need acceptance and clean up any unaccepted ones if
     the socket gets closed.

 (5) Fix the cleanup of client connections.

 (6) Fix the soft-ACK parsing and the retransmission of packets based on
     those ACKs.

 (7) Suppress transmission of an ACK when there's no pending ACK to
     transmit because another thread stole it.

And some miscellany:

 (8) Whitespace removal.

 (9) Switch-value consistency in rxrpc_send_call_packet().

(10) Fix the basic transmission packet size to allow for spur-of-the-moment
     jumbo DATA packet production.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
sched: convert queues to single-linked list

During Netfilter Workshop 2016 Eric Dumazet pointed out that qdisc
schedulers use doubly-linked lists, even though single-linked list
would be enough.

The double-linked skb lists incur one extra write on enqueue/dequeue
operations (to change ->prev pointer of next list elem).

This series converts qdiscs to single-linked version, listhead
maintains pointers to first (for dequeue) and last skb (for enqueue).

Most qdiscs don't queue at all and instead use a leaf qdisc (typically
pfifo_fast) so only a few schedulers needed changes.

I briefly tested netem and htb and they seemed fine.

UDP_STREAM netperf with 64 byte packets via veth+pfifo_fast shows
a small (~2%) improvement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change replaces sk_buff_head struct in Qdiscs with new qdisc_skb_head.

Its similar to the skb_buff_head api, but does not use skb->prev pointers.

Qdiscs will commonly enqueue at the tail of a list and dequeue at head.
While skb_buff_head works fine for this, enqueue/dequeue needs to also
adjust the prev pointer of next element.

The ->prev pointer is not required for qdiscs so we can just leave
it undefined and avoid one cacheline write access for en/dequeue.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

After previous patch these functions are identical.
Replace __skb_dequeue in qdiscs with __qdisc_dequeue_head.

Next patch will then make __qdisc_dequeue_head handle
single-linked list instead of strcut sk_buff_head argument.

Doesn't change generated code.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moves qdisc stat accouting to qdisc_dequeue_head.

The only direct caller of the __qdisc_dequeue_head version open-codes
this now.

This allows us to later use __qdisc_dequeue_head as a replacement
of __skb_dequeue() (which operates on sk_buff_head list).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

A followup change will replace the sk_buff_head in the qdisc
struct with a slightly different list.

Use of the sk_buff_head helpers will thus cause compiler
warnings.

Open-code these accesses in an extra change to ease review.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Doesn't change generated code.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the retrn value check which testing the wrong variable
in cfg_queues_uld().

Fixes: 94cdb8bb ("cxgb4: Add support for dynamic allocation of
resources for ULD")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nelson Chang says:

====================
net: ethernet: mediatek: add HW LRO functions

The series add the large receive offload (LRO) functions by hardware and
the ethtool functions to configure RX flows of HW LRO.

changes since v3:
- Respin the patch by the newer driver
- Move the dts description of hwlro to optional properties

changes since v2:
- Add ndo_fix_features to prevent NETIF_F_LRO off while RX flow is programmed
- Rephrase the dts property is a capability if the hardware supports LRO

changes since v1:
- Add HW LRO support
- Add ethtool hooks to set LRO RX flows
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the dts property for the capability if the hardware supports LRO.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The codes add ethtool functions to set RX flows for HW LRO. Because the
HW LRO hardware can only recognize the destination IP of TCP/IP RX flows,
the ethtool command to add HW LRO flow is as below:
ethtool -N [devname] flow-type tcp4 dst-ip [ip_addr] loc [0~1]

Otherwise, cause the hardware can set total four destination IPs, each
GMAC (GMAC1/GMAC2) can set two IPs separately at most.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The codes add the large receive offload (LRO) functions by hardware as below:
1) PDMA has total four RX rings that one is the normal ring, and others can
   be configured as LRO rings.
2) Only TCP/IP RX flows can be offloaded. The hardware can set four IP
   addresses at most, if the destination IP of the RX flow matches one of
   them, it has the chance to be offloaded.
3) There three RX flows can be offloaded at most, and one flow is mapped to
   one RX ring.
4) If there are more than three candidate RX flows, the hardware can
   choose three of them by throughput comparison results.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocate resources dynamically to cxgb4's Upper layer driver's(ULD) like
cxgbit, iw_cxgb4 and cxgb4i. Allocate resources when they register with
cxgb4 driver and free them while unregistering. All the queues and the
interrupts for them will be allocated during ULD probe only and freed
during remove.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 311b2177 ("sctp: simplify sk_receive_queue locking"), a call
to 'skb_queue_splice_tail_init()' has been made explicit. Previously it was
hidden in 'sctp_skb_list_tail()'

Now, the code around it looks redundant. The '_init()' part of
'skb_queue_splice_tail_init()' should already do the same.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The XDP_TX action can fail transmitting the frame in case the TX ring
is full or port is down.  In case of TX failure it should drop the
frame, and not as now call 'break' which is the same as XDP_PASS.

Fixes: 9ecc2d86 ("net/mlx4_en: add xdp forwarding and data write support")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mahesh Bandewar says:

====================
IPvlan introduce l3s mode

Same old problem with new approach especially from suggestions from
earlier patch-series.

First thing is that this is introduced as a new mode rather than
modifying the old (L3) mode. So the behavior of the existing modes is
preserved as it is and the new L3s mode obeys iptables so that intended
conn-tracking can work.

To do this, the code uses newly added l3mdev_rcv() handler and an
Iptables hook. l3mdev_rcv() to perform an inbound route lookup with the
correct (IPvlan slave) interface and then IPtable-hook at LOCAL_INPUT
to change the input device from master to the slave to complete the
formality.

Supporting stack changes are trivial changes to export symbol to get
IPv4 equivalent code exported for IPv6 and to allow netfilter hook
registration code to allow caller to hold RTNL. Please look into
individual patches for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In a typical IPvlan L3 setup where master is in default-ns and
each slave is into different (slave) ns. In this setup egress
packet processing for traffic originating from slave-ns will
hit all NF_HOOKs in slave-ns as well as default-ns. However same
is not true for ingress processing. All these NF_HOOKs are
hit only in the slave-ns skipping them in the default-ns.
IPvlan in L3 mode is restrictive and if admins want to deploy
iptables rules in default-ns, this asymmetric data path makes it
impossible to do so.

This patch makes use of the l3_rcv() (added as part of l3mdev
enhancements) to perform input route lookup on RX packets without
changing the skb->dev and then uses nf_hook at NF_INET_LOCAL_IN
to change the skb->dev just before handing over skb to L4.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add _nf_register_hooks() and _nf_unregister_hooks() calls which allow
caller to hold RTNL mutex.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make ip6_route_input_lookup available outside of ipv6 the module
similar to ip_route_input_noref in the IPv4 world.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
net: return offloaded stats as default and expose original sw stats

The problem we try to handle is about offloaded forwarded packets
which are not seen by kernel. Let me try to draw it:

    port1                       port2 (HW stats are counted here)
      \                          /
       \                        /
        \                      /
         --(A)---- ASIC --(B)--
                    |
                   (C)
                    |
                   CPU (SW stats are counted here)

Now we have couple of flows for TX and RX (direction does not matter here):

1) port1->A->ASIC->C->CPU

   For this flow, HW and SW stats are equal.

2) port1->A->ASIC->C->CPU->C->ASIC->B->port2

   For this flow, HW and SW stats are equal.

3) port1->A->ASIC->B->port2

   For this flow, SW stats are 0.

The purpose of this patchset is to provide facility for user to
find out the difference between flows 1+2 and 3. In other words, user
will be able to see the statistics for the slow-path (through kernel).

Also note that HW stats are what someone calls "accumulated" stats.
Every packet counted by SW is also counted by HW. Not the other way around.

As a default the accumulated stats (HW) will be exposed to user
so the userspace apps can react properly.

This patchset add the SW stats (flows 1+2) under offload related stats, so
in the future we can expose other offload related stat in a similar way.

---
v9->v10:
- patch 2/3
 - removed unnecessary ()s as pointed out by Nik
v8->v9:
- patch 2/3
 - add using of idxattr and prividx
v7->v8:
- patch 2/3
 - move helping const from uapi to rtnetlink
 - cancel driver xstat nesting if it is empty
v6->v7:
- patch 1/3:
 - ndo interface changed to get the wanted stats type as an input.
 - change commit message.
- patch 2/3:
 - create a nesting for offloaded stat and put SW stats under it.
 - change the ndo call to indicate which offload stats we wants.
 - change commit message.
- patch 3/3:
 - change ndo implementation to match the changes in the previous patches.
 - change commit message.
v5->v6:
- patch 2/4 was dropped as requested by Roopa
- patch 1/3:
 - comment changed to indicate that default stats are combined stats
 - commit massage changed
- patch 2/3: (previously 3/4)
 - SW stats return nothing if there is no SW stats ndo
v4->v5:
- updated cover letter
- patch3/4:
  - using memcpy directly to copy stats as requested by DaveM
v3->v4:
- patch1/4:
  - fixed "return ()" pointed out by EricD
- patch2/4:
  - fixed if_nlmsg_size as pointed out by EricD
v2->v3:
- patch1/4:
  - added dev_have_sw_stats helper
- patch2/4:
  - avoided memcpy as requested by DaveM
- patch3/4:
  - use new dev_have_sw_stats helper
v1->v2:
- patch3/4:
  - fixed NULL initialization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the default statistics ndo to return HW statistics
(like the one returned by ethtool_ops).
The HW stats are collected to a cache by delayed work every 1 sec.
Implement the offload stat ndo.
Add a function to get SW statistics, to be called from this function.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a nested attribute of offload stats to if_stats_msg
named IFLA_STATS_LINK_OFFLOAD_XSTATS.
Under it, add SW stats, meaning stats only per packets that went via
slowpath to the cpu, named IFLA_OFFLOAD_XSTATS_CPU_HIT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new ndo to return statistics for offloaded operation.
Since there can be many different offloaded operation with many
stats types, the ndo gets an attribute id by which it knows which
stats are wanted. The ndo also gets a void pointer to be cast according
to the attribute id.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>