- 07 Jun, 2014 40 commits
-
-
Antti Palosaari authored
commit 8845cc64 upstream. There was some frequency calculation overflows which caused tuning failure on 32-bit architecture. Use 64-bit numbers where needed in order to avoid calculation overflows. Thanks for the Finnish person, who asked remain anonymous, reporting, testing and suggesting the fix. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alex Williamson authored
commit e028a9e6 upstream. An apparent cut and paste error prevents the correct flags from being set on the alias device resulting in MSI on conventional PCI devices failing to work. This also produces error events from the IOMMU like: AMD-Vi: Event logged [INVALID_DEVICE_REQUEST device=00:14.4 address=0x000000fdf8000000 flags=0x0a00] Where 14.4 is a PCIe-to-PCI bridge with a device behind it trying to use MSI interrupts. Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
Joerg Roedel <joro@8bytes.org> Signed-off-by:
-
Chunwei Chen authored
commit 178eda29 upstream. It has been reported that using ZFSonLinux on rbd will result in memory corruption. The bug report can be found here: https://github.com/zfsonlinux/spl/issues/241 http://tracker.ceph.com/issues/7790 The reason is that ZFS will send pages with page_count 0 into rbd, which in turns send them to tcp_sendpage. However, tcp_sendpage cannot deal with page_count 0, as it will do get_page and put_page, and erroneously free the page. This type of issue has been noted before, and handled in iscsi, drbd, etc. So, rbd should also handle this. This fix address this issue by fall back to slower sendmsg when page_count 0 detected. Cc: Sage Weil <sage@inktank.com> Cc: Yehuda Sadeh <yehuda@inktank.com> Signed-off-by:
Chunwei Chen <tuxoko@gmail.com> Reviewed-by:
Ilya Dryomov <ilya.dryomov@inktank.com> Signed-off-by:
-
Geert Uytterhoeven authored
commit 83596fbe upstream. The availability of SPI Dual or Quad Transfer Mode as indicated by the "spi-tx-bus-width" and "spi-rx-bus-width" properties in the device tree is a hardware property of the SPI master, SPI slave, and board wiring. Hence the SPI core should not reject an SPI slave because an SPI master driver doesn't (yet) support Dual or Quad Transfer Mode. Change the lack of Dual or Quad Transfer Mode support in the SPI master driver from an error condition to a warning condition, and ignore the unsupported mode bits, falling back to Single Transfer Mode, to avoid breakages when running old kernels with new device trees. Fixes: f477b7fb (spi: DUAL and QUAD support) Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Srivatsa S. Bhat authored
commit 011e4b02 upstream. If we try to perform a kexec when the machine is in ST (Single-Threaded) mode (ppc64_cpu --smt=off), the kexec operation doesn't succeed properly, and we get the following messages during boot: [ 0.089866] POWER8 performance monitor hardware support registered [ 0.089985] power8-pmu: PMAO restore workaround active. [ 5.095419] Processor 1 is stuck. [ 10.097933] Processor 2 is stuck. [ 15.100480] Processor 3 is stuck. [ 20.102982] Processor 4 is stuck. [ 25.105489] Processor 5 is stuck. [ 30.108005] Processor 6 is stuck. [ 35.110518] Processor 7 is stuck. [ 40.113369] Processor 9 is stuck. [ 45.115879] Processor 10 is stuck. [ 50.118389] Processor 11 is stuck. [ 55.120904] Processor 12 is stuck. [ 60.123425] Processor 13 is stuck. [ 65.125970] Processor 14 is stuck. [ 70.128495] Processor 15 is stuck. [ 75.131316] Processor 17 is stuck. Note that only the sibling threads are stuck, while the primary threads (0, 8, 16 etc) boot just fine. Looking closer at the previous step of kexec, we observe that kexec tries to wakeup (bring online) the sibling threads of all the cores, before performing kexec: [ 9464.131231] Starting new kernel [ 9464.148507] kexec: Waking offline cpu 1. [ 9464.148552] kexec: Waking offline cpu 2. [ 9464.148600] kexec: Waking offline cpu 3. [ 9464.148636] kexec: Waking offline cpu 4. [ 9464.148671] kexec: Waking offline cpu 5. [ 9464.148708] kexec: Waking offline cpu 6. [ 9464.148743] kexec: Waking offline cpu 7. [ 9464.148779] kexec: Waking offline cpu 9. [ 9464.148815] kexec: Waking offline cpu 10. [ 9464.148851] kexec: Waking offline cpu 11. [ 9464.148887] kexec: Waking offline cpu 12. [ 9464.148922] kexec: Waking offline cpu 13. [ 9464.148958] kexec: Waking offline cpu 14. [ 9464.148994] kexec: Waking offline cpu 15. [ 9464.149030] kexec: Waking offline cpu 17. Instrumenting this piece of code revealed that the cpu_up() operation actually fails with -EBUSY. Thus, only the primary threads of all the cores are online during kexec, and hence this is a sure-shot receipe for disaster, as explained in commit e8e5c215 (powerpc/kexec: Fix orphaned offline CPUs across kexec), as well as in the comment above wake_offline_cpus(). It turns out that cpu_up() was returning -EBUSY because the variable 'cpu_hotplug_disabled' was set to 1; and this disabling of CPU hotplug was done by migrate_to_reboot_cpu() inside kernel_kexec(). Now, migrate_to_reboot_cpu() was originally written with the assumption that any further code will not need to perform CPU hotplug, since we are anyway in the reboot path. However, kexec is clearly not such a case, since we depend on onlining CPUs, atleast on powerpc. So re-enable cpu-hotplug after returning from migrate_to_reboot_cpu() in the kexec path, to fix this regression in kexec on powerpc. Also, wrap the cpu_up() in powerpc kexec code within a WARN_ON(), so that we can catch such issues more easily in the future. Fixes: c97102ba (kexec: migrate to reboot cpu) Signed-off-by:
Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Guenter Roeck authored
commit 7998eb3d upstream. With binutils 2.24, various 64 bit builds fail with relocation errors such as arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e': (.text+0x165ee): relocation truncated to fit: R_PPC64_ADDR16_HI against symbol `interrupt_base_book3e' defined in .text section in arch/powerpc/kernel/built-in.o arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e': (.text+0x16602): relocation truncated to fit: R_PPC64_ADDR16_HI against symbol `interrupt_end_book3e' defined in .text section in arch/powerpc/kernel/built-in.o The assembler maintainer says: I changed the ABI, something that had to be done but unfortunately happens to break the booke kernel code. When building up a 64-bit value with lis, ori, shl, oris, ori or similar sequences, you now should use @high and @higha in place of @h and @ha. @h and @ha (and their associated relocs R_PPC64_ADDR16_HI and R_PPC64_ADDR16_HA) now report overflow if the value is out of 32-bit signed range. ie. @h and @ha assume you're building a 32-bit value. This is needed to report out-of-range -mcmodel=medium toc pointer offsets in @toc@h and @toc@ha expressions, and for consistency I did the same for all other @h and @ha relocs. Replacing @h with @high in one strategic location fixes the relocation errors. This has to be done conditionally since the assembler either supports @h or @high but not both. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Anton Blanchard authored
commit 8050936c upstream. I am seeing an issue where a CPU running perf eventually hangs. Traces show timer interrupts happening every 4 seconds even when a userspace task is running on the CPU. /proc/timer_list also shows pending hrtimers have not run in over an hour, including the scheduler. Looking closer, decrementers_next_tb is getting set to 0xffffffffffffffff, and at that point we will never take a timer interrupt again. In __timer_interrupt() we set decrementers_next_tb to 0xffffffffffffffff and rely on ->event_handler to update it: *next_tb = ~(u64)0; if (evt->event_handler) evt->event_handler(evt); In this case ->event_handler is hrtimer_interrupt. This will eventually call back through the clockevents code with the next event to be programmed: static int decrementer_set_next_event(unsigned long evt, struct clock_event_device *dev) { /* Don't adjust the decrementer if some irq work is pending */ if (test_irq_work_pending()) return 0; __get_cpu_var(decrementers_next_tb) = get_tb_or_rtc() + evt; If irq work came in between these two points, we will return before updating decrementers_next_tb and we never process a timer interrupt again. This looks to have been introduced by 0215f7d8 (powerpc: Fix races with irq_work). Fix it by removing the early exit and relying on code later on in the function to force an early decrementer: /* We may have raced with new irq work */ if (test_irq_work_pending()) set_dec(1); Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Gavin Shan authored
commit 372cf124 upstream. Resetting root port has more stuff to do than that for PCIe switch ports and we should have resetting root port done in firmware instead of the kernel itself. The problem was introduced by commit 5b2e198e ("powerpc/powernv: Rework EEH reset"). Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
-
Stephen Boyd authored
commit 874f224c upstream. When a clock is unregsitered, we iterate over the list of children and reparent them to NULL (i.e. orphan list). While iterating the list, we should use the safe iterators because the children list for this clock is changing when we reparent the children to NULL. Failure to iterate safely can lead to slab corruption like this: ============================================================================= BUG kmalloc-128 (Not tainted): Poison overwritten ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: 0xed0c4900-0xed0c4903. First byte 0x0 instead of 0x6b INFO: Allocated in clk_register+0x20/0x1bc age=297 cpu=2 pid=70 __slab_alloc.isra.39.constprop.42+0x410/0x454 kmem_cache_alloc_trace+0x200/0x24c clk_register+0x20/0x1bc devm_clk_register+0x34/0x68 0xbf0000f0 platform_drv_probe+0x18/0x48 driver_probe_device+0x94/0x360 __driver_attach+0x94/0x98 bus_for_each_dev+0x54/0x88 bus_add_driver+0xe8/0x204 driver_register+0x78/0xf4 do_one_initcall+0xc4/0x17c load_module+0x19ac/0x2294 SyS_init_module+0xa4/0x110 ret_fast_syscall+0x0/0x48 INFO: Freed in clk_unregister+0xd4/0x140 age=23 cpu=2 pid=73 __slab_free+0x38/0x41c clk_unregister+0xd4/0x140 release_nodes+0x164/0x1d8 __device_release_driver+0x60/0xb0 driver_detach+0xb4/0xb8 bus_remove_driver+0x5c/0xc4 SyS_delete_module+0x148/0x1d8 ret_fast_syscall+0x0/0x48 INFO: Slab 0xeec50b90 objects=25 used=0 fp=0xed0c5400 flags=0x4080 INFO: Object 0xed0c48c0 @offset=2240 fp=0xed0c4a00 Bytes b4 ed0c48b0: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ Object ed0c48c0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ed0c48d0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ed0c48e0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ed0c48f0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ed0c4900: 00 00 00 00 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b ....kkkkkkkkkkkk Object ed0c4910: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ed0c4920: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ed0c4930: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkkkkkkkkkk. Redzone ed0c4940: bb bb bb bb .... Padding ed0c49e8: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ Padding ed0c49f8: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ CPU: 3 PID: 75 Comm: mdev Tainted: G B 3.14.0-11033-g2054ba5ca781 #35 [<c0014be0>] (unwind_backtrace) from [<c0012240>] (show_stack+0x10/0x14) [<c0012240>] (show_stack) from [<c04b74a0>] (dump_stack+0x70/0xbc) [<c04b74a0>] (dump_stack) from [<c00f7a78>] (check_bytes_and_report+0xbc/0x100) [<c00f7a78>] (check_bytes_and_report) from [<c00f7c48>] (check_object+0x18c/0x218) [<c00f7c48>] (check_object) from [<c00f7efc>] (__free_slab+0x104/0x144) [<c00f7efc>] (__free_slab) from [<c04b6668>] (__slab_free+0x3dc/0x41c) [<c04b6668>] (__slab_free) from [<c014c008>] (load_elf_binary+0x88/0x12b4) [<c014c008>] (load_elf_binary) from [<c0105a44>] (search_binary_handler+0x78/0x18c) [<c0105a44>] (search_binary_handler) from [<c0106fc0>] (do_execve+0x490/0x5dc) [<c0106fc0>] (do_execve) from [<c0036b8c>] (____call_usermodehelper+0x134/0x168) [<c0036b8c>] (____call_usermodehelper) from [<c000f048>] (ret_from_fork+0x14/0x2c) FIX kmalloc-128: Restoring 0xed0c4900-0xed0c4903=0x6b Fixes: fcb0ee6a (clk: Implement clk_unregister) Cc: Jiada Wang <jiada_wang@mentor.com> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
Mike Turquette <mturquette@linaro.org> Signed-off-by:
-
Stephen Boyd authored
commit 293ba3b4 upstream. Now that clk_unregister() frees the struct clk we're unregistering we'll free memory twice: first we'll call kfree() in __clk_release() with an address kmalloc doesn't know about and second we'll call kfree() in the devres layer. Remove the allocation of struct clk in devm_clk_register() and let clk_release() handle it. This fixes slab errors like: ============================================================================= BUG kmalloc-128 (Not tainted): Invalid object pointer 0xed08e8d0 ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Slab 0xeec503f8 objects=25 used=15 fp=0xed08ea00 flags=0x4081 CPU: 2 PID: 73 Comm: rmmod Tainted: G B 3.14.0-11032-g526e9c764381 #34 [<c0014be0>] (unwind_backtrace) from [<c0012240>] (show_stack+0x10/0x14) [<c0012240>] (show_stack) from [<c04b74dc>] (dump_stack+0x70/0xbc) [<c04b74dc>] (dump_stack) from [<c00f6778>] (slab_err+0x74/0x84) [<c00f6778>] (slab_err) from [<c04b6278>] (free_debug_processing+0x2cc/0x31c) [<c04b6278>] (free_debug_processing) from [<c04b6300>] (__slab_free+0x38/0x41c) [<c04b6300>] (__slab_free) from [<c03931bc>] (clk_unregister+0xd4/0x140) [<c03931bc>] (clk_unregister) from [<c02fb774>] (release_nodes+0x164/0x1d8) [<c02fb774>] (release_nodes) from [<c02f8698>] (__device_release_driver+0x60/0xb0) [<c02f8698>] (__device_release_driver) from [<c02f9080>] (driver_detach+0xb4/0xb8) [<c02f9080>] (driver_detach) from [<c02f8480>] (bus_remove_driver+0x5c/0xc4) [<c02f8480>] (bus_remove_driver) from [<c008c9b8>] (SyS_delete_module+0x148/0x1d8) [<c008c9b8>] (SyS_delete_module) from [<c000ef80>] (ret_fast_syscall+0x0/0x48) FIX kmalloc-128: Object at 0xed08e8d0 not freed Fixes: fcb0ee6a (clk: Implement clk_unregister) Cc: Jiada Wang <jiada_wang@mentor.com> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Harald Freudenberger authored
commit 3901c112 upstream. An additional testcase found an issue with the last series of patches applied: the fallback solution may not save the iv value after operation. This very small fix just makes sure the iv is copied back to the walk/desc struct. Signed-off-by:
Harald Freudenberger <freude@linux.vnet.ibm.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Horia Geanta authored
commit 27c5fb7a upstream. GFP_ATOMIC memory allocation could fail. In this case, avoid NULL pointer dereference and notify user. Cc: Kim Phillips <kim.phillips@freescale.com> Signed-off-by:
Horia Geanta <horia.geanta@freescale.com> Signed-off-by:
-
Dirk Brandewie authored
commit d40a63c4 upstream. Setting the P state of the core to max at init time is a hold over from early implementation of intel_pstate where intel_pstate disabled cpufreq and loaded VERY early in the boot sequence. This was to ensure that intel_pstate did not affect boot time. This in not needed now that intel_pstate is a cpufreq driver. Removing this covers the case where a CPU has gone through a manual CPU offline/online cycle and the P state is set to MAX on init and the CPU immediately goes idle. Due to HW coordination the P state request on the idle CPU will drag all cores to MAX P state until the load is reevaluated when to core goes non-idle. Reported-by:
Patrick Marlier <patrick.marlier@gmail.com> Signed-off-by:
Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dirk Brandewie authored
commit 21855ff5 upstream. A documentation update exposed that there is a separate set of VID values that must be used in the turbo/boost P state range. Add enumerating and setting the correct VID for P states in the turbo range. Signed-off-by:
-
Olof Johansson authored
commit ce78cc07 upstream. Don't unmark the device as suspended until after it's been re-setup. The main race would be w.r.t. an i2c driver that gets resumed at the same time (asyncronously), that is allowed to do a transfer since suspended is set to 0 before reinit, but really should have seen the -EIO return instead. Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
Doug Anderson <dianders@chromium.org> Acked-by:
Kukjin Kim <kgene.kim@samsung.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Du, Wenkai authored
commit 47bb27e7 upstream. There have been "i2c_designware 80860F41:00: controller timed out" errors on a number of Baytrail platforms. The issue is caused by incorrect value in Interrupt Mask Register (DW_IC_INTR_MASK) when i2c core is being enabled. This causes call to __i2c_dw_enable() to immediately start the transfer which leads to timeout. There are 3 failure modes observed: 1. Failure in S0 to S3 resume path The default value after reset for DW_IC_INTR_MASK is 0x8ff. When we start the first transaction after resuming from system sleep, TX_EMPTY interrupt is already unmasked because of the hardware default. 2. Failure in normal operational path This failure happens rarely and is hard to reproduce. Debug trace showed that DW_IC_INTR_MASK had value of 0x254 when failure occurred, which meant TX_EMPTY was unmasked. 3. Failure in S3 to S0 suspend path This failure also happens rarely and is hard to reproduce. Adding debug trace that read DW_IC_INTR_MASK made this failure not reproducible. But from ISR call trace we could conclude TX_EMPTY was unmasked when problem occurred. The patch masks all interrupts before the controller is enabled to resolve the faulty DW_IC_INTR_MASK conditions. Signed-off-by:
Wenkai Du <wenkai.du@intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> [wsa: improved the comment and removed typo in commit msg] Signed-off-by:
-
Wolfram Sang authored
commit d7653964 upstream. This hardware does not support zero length transfers. Instead, the driver does one (random) byte transfers currently with undefined results for the slaves. We now bail out. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
Hans de Goede authored
commit 07d1d29e upstream. Seems it helps some users, but causes issues for other users: https://bugzilla.redhat.com/show_bug.cgi?id=1089545 So lets drop it for now until we've figured out a better fix. Fixes: 43d94902 (ACPI / video: Add use_native_backlight quirks for more systems) References: https://bugzilla.redhat.com/show_bug.cgi?id=1089545Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Aaron Lu authored
commit 5ff365fb upstream. The DMI tag used to identify Dell Inspiron 7520 should be product name instead of product version. Fixes: 0e9f81d3 (ACPI / video: Add systems that should favour native backlight interface) Reported-and-tested-by:
Téo Mazars <teomazars@gmail.com> References: https://bugzilla.redhat.com/show_bug.cgi?id=909552Signed-off-by:
Aaron Lu <aaron.lu@intel.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit f7595464 upstream. Chromebooks (at least Acer C720 and Pixel) implement an ACPI object for TPM, but don't implement the _DSM method to support PPI. As a result, the TPM driver fails to load on those machines after commit 1569a4c4 (ACPI / TPM: detect PPI features by checking availability of _DSM functions) which causes them to fail to resume from system suspend, becuase they require the TPM hardware to be put into the right state during resume and the TPM driver is necessary for that. Fix the problem by making tpm_add_ppi() return 0 when tpm_ppi_handle is still NULL after walking the ACPI namespace in search for the PPI _DSM, which allows the TPM driver to load and operate the hardware (during system resume in particular), but avoid creating the PPI sysfs group in that case. This change is based on a prototype patch from Jiang Liu. Fixes: 1569a4c4 (ACPI / TPM: detect PPI features by checking availability of _DSM functions) References: https://bugzilla.kernel.org/show_bug.cgi?id=74021Reported-by:
James Duley <jagduley@gmail.com> Reported-by:
Phillip Dixon <phil@dixon.gen.nz> Tested-by:
Brandon Casey <drafnel@gmail.com> Signed-off-by:
-
Edward Lin authored
commit b753631b upstream. With win8 capabiltiy, the machine will boot itself immediately after shutdown command has executed. Work around this issue by disabling win8 capcability. This workaround also makes wireless hotkey work. Signed-off-by:
Edward Lin <yidi.lin@canonical.com> Signed-off-by:
-
Guenter Roeck authored
commit 98012849 upstream. Revert commit cc8ef527 (ACPI / AC: convert ACPI ac driver to platform bus) that is reported to break thermal management on MacBook Air 2013 with ArchLinux. Fixes: cc8ef527 (ACPI / AC: convert ACPI ac driver to platform bus) References: https://bugzilla.kernel.org/show_bug.cgi?id=71711 Cc: Zhang Rui <rui.zhang@intel.com> Reported-and-tested-by:
Manuel Krause <manuelkrause@netscape.net> Signed-off-by:
-
Igor Mammedov authored
commit 0b9d46dd upstream. acpi_processor_add() assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As result acpi_processor_add() will mark such CPU device as onlined in sysfs and following attempts to online/offline it using /sys/device/system/cpu/cpuX/online attribute will fail. Do not poke into device internals in acpi_processor_add() and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by: topology_init() -> arch_register_cpu() -> register_cpu() before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs. Signed-off-by:
Igor Mammedov <imammedo@redhat.com> Acked-by:
Toshi Kani <toshi.kani@hp.com> Signed-off-by:
-
Hans de Goede authored
commit f6e6e1b9 upstream. Without this this EEE PC exports a non working WMI interface, with this it exports a working "good old" eeepc_laptop interface, fixing brightness control not working as well as rfkill being stuck in a permanent wireless blocked state. This is not an ideal way to fix this, but various attempts to fix this otherwise have failed, see: References: https://bugzilla.redhat.com/show_bug.cgi?id=1067181 Reported-and-tested-by: lou.cardone@gmail.com Signed-off-by:
-
Hans de Goede authored
commit 43d94902 upstream. ThinkPad T430: extend the T430s entry to also cover the T430 (note we also have another entry for T430's with a different DMI_PRODUCT_VERSION). ThinkPad T430 Reported-and-tested-by:
edm <fuffi.il.fuffo@gmail.com> References: https://bugzilla.kernel.org/show_bug.cgi?id=51231 Thinkpad T530 Reported-and-tested-by:
Balint Szigeti <balint.szgt@gmail.com> References: https://bugzilla.redhat.com/show_bug.cgi?id=1089545 Acer Aspire 5742G Reported-and-tested-by:
AnAkkk <anakin.cs@gmail.com> References: https://bugzilla.kernel.org/show_bug.cgi?id=35622Signed-off-by:
-
Lan Tianyu authored
commit 3a670cc7 upstream. The commit 1e2d9cdf and 7d7ee958 remove ACPI Proc Battery directory and breaks some old userspace tools. This patch is to revert commit 1e2d9cdf. Fixes: 1e2d9cdf (ACPI / Battery: Remove battery's proc directory) Signed-off-by:
Lan Tianyu <tianyu.lan@intel.com> Signed-off-by:
-
Lan Tianyu authored
commit e2a7c3d7 upstream. The commit 1e2d9cdf and 7d7ee958 remove ACPI Proc Battery directory and breaks some old userspace tools. This patch is to revert 7d7ee958. Fixes: 7d7ee958 (ACPI: Remove CONFIG_ACPI_PROCFS_POWER and cm_sbsc.c) Signed-off-by:
-
Lv Zheng authored
commit 85dbd580 upstream. We need to find a smarter way to switch to 64-bit FADT addresses according to the bug report. This patch reverts Linux to the original behavior. Fixes: 0249ed24 (ACPICA: Add option to favor 32-bit FADT addresses.) References: https://bugzilla.kernel.org/show_bug.cgi?id=74021Reported-and-tested-by:
Oswald Buddenhagen <ossi@kde.org> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
-
Lv Zheng authored
commit d48dc067 upstream. Linux XSDT validation mechanism backport has introduced a regreession: Commit: 671cc68d Subject: ACPICA: Back port and refine validation of the XSDT root table. There is a pointer still accessed after unmapping. This patch fixes this issue. Lv Zheng. Fixes: 671cc68d (ACPICA: Back port and refine validation of the XSDT root table.) References: https://bugzilla.kernel.org/show_bug.cgi?id=73911 References: https://bugs.archlinux.org/task/39811Signed-off-by:
Bruce Chiarelli <mano155@gmail.com> Reported-and-tested-by:
Spyros Stathopoulos <spystath@gmail.com> Signed-off-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
-
Levente Kurusa authored
commit a6f9bf4d upstream. When a ZPODD device is unbound via sysfs, the ACPI notify handler is not removed. This causes panics as observed in Bug #74601. The panic only happens when the wake happens from outside the kernel (i.e. inserting a media or pressing a button). Add a loop to ata_port_detach which loops through the port's devices and checks if zpodd is enabled, if so call zpodd_exit. Reviewed-by:
Levente Kurusa <levex@linux.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Nicholas Bellinger authored
commit ed8ec8f7 upstream. This patch fixes a free-after-use regression in ft_free_cmd(), where ft_sess_put() is called with cmd->sess after percpu_ida_free() has already released the tag. Fix this bug by saving the ft_sess pointer ahead of percpu_ida_free(), and pass it directly to ft_sess_put(). The regression was originally introduced in v3.13-rc1 commit: commit 5f544cfa Author: Nicholas Bellinger <nab@daterainc.com> Date: Mon Sep 23 12:12:42 2013 -0700 tcm_fc: Convert to per-cpu command map pre-allocation of ft_cmd Reported-by:
Jun Wu <jwu@stormojo.com> Cc: Mark Rustad <mark.d.rustad@intel.com> Cc: Robert Love <robert.w.love@intel.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Andy Shevchenko authored
commit 97977f75 upstream. The commit dbde5c29 "dw_dmac: use devm_* functions to simplify code" turns probe function to use devm_* helpers and simultaneously brings a regression. We need to ensure irq is disabled, followed by ensuring that don't schedule any more tasklets and then its safe to use tasklet_kill(). The free_irq() will ensure that the irq is disabled and also wait till all scheduled interrupts are executed by invoking synchronize_irq(). So we need to only do tasklet_kill() after invoking free_irq(). Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Ezequiel Garcia authored
commit 5a9a55bf upstream. We need to use writel() instead of writel_relaxed() when starting a channel, to ensure all the descriptors have been flushed before the activation. While at it, remove the unneeded read-modify-write and make the code simpler. Signed-off-by:
Lior Amsalem <alior@marvell.com> Signed-off-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Xuelin Shi authored
commit c1f43dd9 upstream. The count which is used to get_unmap_data maybe not the same as the count computed in dmaengine_unmap which causes to free data in a wrong pool. This patch fixes this issue by keeping the map count with unmap_data structure and use this count to get the pool. Signed-off-by:
Xuelin Shi <xuelin.shi@freescale.com> Signed-off-by:
-
Joe Thornber authored
commit 85ad643b upstream. If the pool runs out of data space, dm-thin can be configured to either error IOs that would trigger provisioning, or hold those IOs until the pool is resized. Unfortunately, holding IOs until the pool is resized can result in a cascade of tasks hitting the hung_task_timeout, which may render the system unavailable. Add a fixed timeout so IOs can only be held for a maximum of 60 seconds. If LVM is going to resize a thin-pool that is out of data space it needs to be prompt about it. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit 8d07e8a5 upstream. Commit 3e1a0699 ("dm thin: fix out of data space handling") introduced a regression in the metadata commit() method by returning an error if the pool is in PM_OUT_OF_DATA_SPACE mode. This oversight caused a thin device to return errors even if the default queue_if_no_space ENOSPC handling mode is used. Fix commit() to only fail if pool is in PM_READ_ONLY or PM_FAIL mode. Reported-by: qindehua@163.com Signed-off-by:
-
Mikulas Patocka authored
commit 610f2de3 upstream. The DM crypt target used per-cpu structures to hold pointers to a ablkcipher_request structure. The code assumed that the work item keeps executing on a single CPU, so it didn't use synchronization when accessing this structure. If a CPU is disabled by writing 0 to /sys/devices/system/cpu/cpu*/online, the work item could be moved to another CPU. This causes dm-crypt crashes, like the following, because the code starts using an incorrect ablkcipher_request: smpboot: CPU 7 is now offline BUG: unable to handle kernel NULL pointer dereference at 0000000000000130 IP: [<ffffffffa1862b3d>] crypt_convert+0x12d/0x3c0 [dm_crypt] ... Call Trace: [<ffffffffa1864415>] ? kcryptd_crypt+0x305/0x470 [dm_crypt] [<ffffffff81062060>] ? finish_task_switch+0x40/0xc0 [<ffffffff81052a28>] ? process_one_work+0x168/0x470 [<ffffffff8105366b>] ? worker_thread+0x10b/0x390 [<ffffffff81053560>] ? manage_workers.isra.26+0x290/0x290 [<ffffffff81058d9f>] ? kthread+0xaf/0xc0 [<ffffffff81058cf0>] ? kthread_create_on_node+0x120/0x120 [<ffffffff813464ac>] ? ret_from_fork+0x7c/0xb0 [<ffffffff81058cf0>] ? kthread_create_on_node+0x120/0x120 Fix this bug by removing the per-cpu definition. The structure ablkcipher_request is accessed via a pointer from convert_context. Consequently, if the work item is rescheduled to a different CPU, the thread still uses the same ablkcipher_request. This change may undermine performance improvements intended by commit c0297721 ("dm crypt: scale to multiple cpus") on select hardware. In practice no performance difference was observed on recent hardware. But regardless, correctness is more important than performance. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Gavin Shan authored
commit d0b4cc4e upstream. The incorrect register offset is passed to pci_wait_for_pending(), which is caused by commit 157e876f ("PCI: Add pci_wait_for_pending() (refactor pci_wait_for_pending_transaction())"). Fixes: 157e876f ("PCI: Add pci_wait_for_pending() (refactor pci_wait_for_pending_transaction()) Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Alex Williamson <alex.williamson@gmail.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit a6bc9280 upstream. A few entries were wrong and this caused throughput issues. Fixes: dac94da8 ("iwlwifi: mvm: new BT Coex API") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Jani Nikula authored
This is commit 0f540c3a upstream. Since commit ee1452d7 Author: Jani Nikula <jani.nikula@intel.com> Date: Fri Sep 20 15:05:30 2013 +0300 drm/i915: assume all GM45 Acer laptops use inverted backlight PWM failed and was later reverted in commit be505f64 Author: Alexander van Heukelum <heukelum@fastmail.fm> Date: Sat Dec 28 21:00:39 2013 +0100 Revert "drm/i915: assume all GM45 Acer laptops use inverted backlight PWM" fix the individual broken machine instead. Note to backporters: http://patchwork.freedesktop.org/patch/17837/ is the patch you want for 3.13 and older. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54171 Reference: http://mid.gmane.org/DUB115-W7628C7C710EA51AA110CD4A5000@phx.gblSigned-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> [danvet: Patch mangling for 3.14 plus adding the link to the original for 3.13.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
