- 04 Apr, 2019 22 commits
-
-
Piotr Figiel authored
Fix a race which leads to an Oops with NULL pointer dereference. The dereference is in brcmf_config_dongle() when cfg_to_ndev() attempts to get net_device structure of interface with index 0 via if2bss mapping. This shouldn't fail because of check for bus being ready in brcmf_netdev_open(), but it's not synchronised with USB disconnect and there is a race: after the check the bus can be marked down and the mapping for interface 0 may be gone. Solve this by modifying disconnect handling so that the removal of mapping of ifidx to brcmf_if structure happens after netdev removal (which is synchronous with brcmf_netdev_open() thanks to rtln being locked in devinet_ioctl()). This assures brcmf_netdev_open() returns before the mapping is removed during disconnect. Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = bcae2612 [00000008] *pgd=8be73831 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: brcmfmac brcmutil nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether usb_serial_simple usbserial cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc usbmisc_imx ulpi 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core [last unloaded: brcmutil] CPU: 2 PID: 24478 Comm: ifconfig Not tainted 4.19.23-00078-ga62866d-dirty #115 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) PC is at brcmf_cfg80211_up+0x94/0x29c [brcmfmac] LR is at brcmf_cfg80211_up+0x8c/0x29c [brcmfmac] pc : [<7f26a91c>] lr : [<7f26a914>] psr: a0070013 sp : eca99d28 ip : 00000000 fp : ee9c6c00 r10: 00000036 r9 : 00000000 r8 : ece4002c r7 : edb5b800 r6 : 00000000 r5 : 80f08448 r4 : edb5b968 r3 : ffffffff r2 : 00000000 r1 : 00000002 r0 : 00000000 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 7ca0c04a DAC: 00000051 Process ifconfig (pid: 24478, stack limit = 0xd9e85a0e) Stack: (0xeca99d28 to 0xeca9a000) 9d20: 00000000 80f873b0 0000000d 80f08448 eca99d68 50d45f32 9d40: 7f27de94 ece40000 80f08448 80f08448 7f27de94 ece4002c 00000000 00000036 9d60: ee9c6c00 7f27262c 00001002 50d45f32 ece40000 00000000 80f08448 80772008 9d80: 00000001 00001043 00001002 ece40000 00000000 50d45f32 ece40000 00000001 9da0: 80f08448 00001043 00001002 807723d0 00000000 50d45f32 80f08448 eca99e58 9dc0: 80f87113 50d45f32 80f08448 ece40000 ece40138 00001002 80f08448 00000000 9de0: 00000000 80772434 edbd5380 eca99e58 edbd5380 80f08448 ee9c6c0c 80805f70 9e00: 00000000 ede08e00 00008914 ece40000 00000014 ee9c6c0c 600c0013 00001043 9e20: 0208a8c0 ffffffff 00000000 50d45f32 eca98000 80f08448 7ee9fc38 00008914 9e40: 80f68e40 00000051 eca98000 00000036 00000003 80808b9c 6e616c77 00000030 9e60: 00000000 00000000 00001043 0208a8c0 ffffffff 00000000 80f08448 00000000 9e80: 00000000 816d8b20 600c0013 00000001 ede09320 801763d4 00000000 50d45f32 9ea0: eca98000 80f08448 7ee9fc38 50d45f32 00008914 80f08448 7ee9fc38 80f68e40 9ec0: ed531540 8074721c 00000800 00000001 00000000 6e616c77 00000030 00000000 9ee0: 00000000 00001002 0208a8c0 ffffffff 00000000 50d45f32 80f08448 7ee9fc38 9f00: ed531560 ec8fc900 80285a6c 80285138 edb910c0 00000000 ecd91008 ede08e00 9f20: 80f08448 00000000 00000000 816d8b20 600c0013 00000001 ede09320 801763d4 9f40: 00000000 50d45f32 00021000 edb91118 edb910c0 80f08448 01b29000 edb91118 9f60: eca99f7c 50d45f32 00021000 ec8fc900 00000003 ec8fc900 00008914 7ee9fc38 9f80: eca98000 00000036 00000003 80285a6c 00086364 7ee9fe1c 000000c3 00000036 9fa0: 801011c4 80101000 00086364 7ee9fe1c 00000003 00008914 7ee9fc38 00086364 9fc0: 00086364 7ee9fe1c 000000c3 00000036 0008630c 7ee9fe1c 7ee9fc38 00000003 9fe0: 000a42b8 7ee9fbd4 00019914 76e09acc 600c0010 00000003 00000000 00000000 [<7f26a91c>] (brcmf_cfg80211_up [brcmfmac]) from [<7f27262c>] (brcmf_netdev_open+0x74/0xe8 [brcmfmac]) [<7f27262c>] (brcmf_netdev_open [brcmfmac]) from [<80772008>] (__dev_open+0xcc/0x150) [<80772008>] (__dev_open) from [<807723d0>] (__dev_change_flags+0x168/0x1b4) [<807723d0>] (__dev_change_flags) from [<80772434>] (dev_change_flags+0x18/0x48) [<80772434>] (dev_change_flags) from [<80805f70>] (devinet_ioctl+0x67c/0x79c) [<80805f70>] (devinet_ioctl) from [<80808b9c>] (inet_ioctl+0x210/0x3d4) [<80808b9c>] (inet_ioctl) from [<8074721c>] (sock_ioctl+0x350/0x524) [<8074721c>] (sock_ioctl) from [<80285138>] (do_vfs_ioctl+0xb0/0x9b0) [<80285138>] (do_vfs_ioctl) from [<80285a6c>] (ksys_ioctl+0x34/0x5c) [<80285a6c>] (ksys_ioctl) from [<80101000>] (ret_fast_syscall+0x0/0x28) Exception stack(0xeca99fa8 to 0xeca99ff0) 9fa0: 00086364 7ee9fe1c 00000003 00008914 7ee9fc38 00086364 9fc0: 00086364 7ee9fe1c 000000c3 00000036 0008630c 7ee9fe1c 7ee9fc38 00000003 9fe0: 000a42b8 7ee9fbd4 00019914 76e09acc Code: e5970328 eb002021 e1a02006 e3a01002 (e5909008) ---[ end trace 5cbac2333f3ac5df ]--- Signed-off-by:
Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Piotr Figiel authored
Variable i is not used so remove it. Signed-off-by:
-
Piotr Figiel authored
brcmf_usb_free_q is no longer called with pending=true thus this boolean parameter is no longer needed. Signed-off-by:
-
Piotr Figiel authored
It was observed that rarely during USB disconnect happening shortly after connect (before full initialization completes) usb_hub_wq would wait forever for the dev_init_lock to be unlocked. dev_init_lock would remain locked though because of infinite wait during usb_kill_urb: [ 2730.656472] kworker/0:2 D 0 260 2 0x00000000 [ 2730.660700] Workqueue: events request_firmware_work_func [ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac) [ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114) [ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac]) [ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac]) [ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac]) [ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac]) [ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac]) [ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88) [ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808) [ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) [ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000 [ 2733.103926] Workqueue: usb_hub_wq hub_event [ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac) [ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4) [ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0) [ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac]) [ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4) [ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc) [ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc) [ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310) [ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc) [ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc) [ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88) [ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808) [ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) It was traced down to a case where usb_kill_urb would be called on an URB structure containing more or less random data, including large number in its use_count. During the debugging it appeared that in brcmf_usb_free_q() the traversal over URBs' lists is not synchronized with operations on those lists in brcmf_usb_rx_complete() leading to handling brcmf_usbdev_info structure (holding lists' head) as lists' element and in result causing above problem. Fix it by walking through all URBs during brcmf_cancel_all_urbs using the arrays of requests instead of linked lists. Signed-off-by:
-
Piotr Figiel authored
In case USB disconnect happens at the moment transmitting workqueue is in progress the underlying interface may be gone causing a NULL pointer dereference. Add synchronization of the workqueue destruction with the detach implementation in core so that the transmitting workqueue is stopped during detach before the interfaces are removed. Fix following Oops: Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = 9e6a802d [00000008] *pgd=00000000 Internal error: Oops: 5 [#1] PREEMPT SMP ARM Modules linked in: nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether usb_serial_simple usbserial cdc_acm brcmfmac brcmutil smsc95xx usbnet ci_hdrc_imx ci_hdrc ulpi usbmisc_imx 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core CPU: 0 PID: 7 Comm: kworker/u8:0 Not tainted 4.19.23-00076-g03740aa-dirty #102 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: brcmf_fws_wq brcmf_fws_dequeue_worker [brcmfmac] PC is at brcmf_txfinalize+0x34/0x90 [brcmfmac] LR is at brcmf_fws_dequeue_worker+0x218/0x33c [brcmfmac] pc : [<7f0dee64>] lr : [<7f0e4140>] psr: 60010093 sp : ee8abef0 ip : 00000000 fp : edf38000 r10: ffffffed r9 : edf38970 r8 : edf38004 r7 : edf3e970 r6 : 00000000 r5 : ede69000 r4 : 00000000 r3 : 00000a97 r2 : 00000000 r1 : 0000888e r0 : ede69000 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 7d03c04a DAC: 00000051 Process kworker/u8:0 (pid: 7, stack limit = 0x24ec3e04) Stack: (0xee8abef0 to 0xee8ac000) bee0: ede69000 00000000 ed56c3e0 7f0e4140 bf00: 00000001 00000000 edf38004 edf3e99c ed56c3e0 80d03d00 edfea43a edf3e970 bf20: ee809880 ee804200 ee971100 00000000 edf3e974 00000000 ee804200 80135a70 bf40: 80d03d00 ee804218 ee809880 ee809894 ee804200 80d03d00 ee804218 ee8aa000 bf60: 00000088 80135d5c 00000000 ee829f00 ee829dc0 00000000 ee809880 80135d30 bf80: ee829f1c ee873eac 00000000 8013b1a0 ee829dc0 8013b07c 00000000 00000000 bfa0: 00000000 00000000 00000000 801010e8 00000000 00000000 00000000 00000000 bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [<7f0dee64>] (brcmf_txfinalize [brcmfmac]) from [<7f0e4140>] (brcmf_fws_dequeue_worker+0x218/0x33c [brcmfmac]) [<7f0e4140>] (brcmf_fws_dequeue_worker [brcmfmac]) from [<80135a70>] (process_one_work+0x138/0x3f8) [<80135a70>] (process_one_work) from [<80135d5c>] (worker_thread+0x2c/0x554) [<80135d5c>] (worker_thread) from [<8013b1a0>] (kthread+0x124/0x154) [<8013b1a0>] (kthread) from [<801010e8>] (ret_from_fork+0x14/0x2c) Exception stack(0xee8abfb0 to 0xee8abff8) bfa0: 00000000 00000000 00000000 00000000 bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 Code: e1530001 0a000007 e3560000 e1a00005 (05942008) ---[ end trace 079239dd31c86e90 ]--- Signed-off-by:
-
Piotr Figiel authored
brcmu_pkt_buf_free_skb emits WARNING when attempting to free a sk_buff which is part of any queue. After USB disconnect this may have happened when brcmf_fws_hanger_cleanup() is called as per-interface psq was never cleaned when removing the interface. Change brcmf_fws_macdesc_cleanup() in a way that it removes the corresponding packets from hanger table (to avoid double-free when brcmf_fws_hanger_cleanup() is called) and add a call to clean-up the interface specific packet queue. Below is a WARNING during USB disconnect with Raspberry Pi WiFi dongle running in AP mode. This was reproducible when the interface was transmitting during the disconnect and is fixed with this commit. ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1171 at drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49 brcmu_pkt_buf_free_skb+0x3c/0x40 Modules linked in: nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc ulpi usbmisc_imx 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core CPU: 0 PID: 1171 Comm: kworker/0:0 Not tainted 4.19.23-00075-gde33ed8 #99 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: usb_hub_wq hub_event [<8010ff84>] (unwind_backtrace) from [<8010bb64>] (show_stack+0x10/0x14) [<8010bb64>] (show_stack) from [<80840278>] (dump_stack+0x88/0x9c) [<80840278>] (dump_stack) from [<8011f5ec>] (__warn+0xfc/0x114) [<8011f5ec>] (__warn) from [<8011f71c>] (warn_slowpath_null+0x40/0x48) [<8011f71c>] (warn_slowpath_null) from [<805a476c>] (brcmu_pkt_buf_free_skb+0x3c/0x40) [<805a476c>] (brcmu_pkt_buf_free_skb) from [<805bb6c4>] (brcmf_fws_cleanup+0x1e4/0x22c) [<805bb6c4>] (brcmf_fws_cleanup) from [<805bc854>] (brcmf_fws_del_interface+0x58/0x68) [<805bc854>] (brcmf_fws_del_interface) from [<805b66ac>] (brcmf_remove_interface+0x40/0x150) [<805b66ac>] (brcmf_remove_interface) from [<805b6870>] (brcmf_detach+0x6c/0xb0) [<805b6870>] (brcmf_detach) from [<805bdbb8>] (brcmf_usb_disconnect+0x30/0x4c) [<805bdbb8>] (brcmf_usb_disconnect) from [<805e5d64>] (usb_unbind_interface+0x5c/0x1e0) [<805e5d64>] (usb_unbind_interface) from [<804aab10>] (device_release_driver_internal+0x154/0x1ec) [<804aab10>] (device_release_driver_internal) from [<804a97f4>] (bus_remove_device+0xcc/0xf8) [<804a97f4>] (bus_remove_device) from [<804a6fc0>] (device_del+0x118/0x308) [<804a6fc0>] (device_del) from [<805e488c>] (usb_disable_device+0xa0/0x1c8) [<805e488c>] (usb_disable_device) from [<805dcf98>] (usb_disconnect+0x70/0x1d8) [<805dcf98>] (usb_disconnect) from [<805ddd84>] (hub_event+0x464/0xf50) [<805ddd84>] (hub_event) from [<80135a70>] (process_one_work+0x138/0x3f8) [<80135a70>] (process_one_work) from [<80135d5c>] (worker_thread+0x2c/0x554) [<80135d5c>] (worker_thread) from [<8013b1a0>] (kthread+0x124/0x154) [<8013b1a0>] (kthread) from [<801010e8>] (ret_from_fork+0x14/0x2c) Exception stack(0xecf8dfb0 to 0xecf8dff8) dfa0: 00000000 00000000 00000000 00000000 dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 ---[ end trace 38d234018e9e2a90 ]--- ------------[ cut here ]------------ Signed-off-by:
-
Rafał Miłecki authored
This includes bus reset & reloading a firmware. It should be sufficient for a user space to (setup and) use a wireless device again. Support for reset on USB & SDIO can be added later. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Reviewed-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
Rafał Miłecki authored
This improves handling PCIe firmware halts by printing a clear error message and replaces a similar code in the SDIO bus support. It will also allow further improvements like trying to recover from a firmware crash. Signed-off-by:
-
Rafał Miłecki authored
During a normal brcmfmac lifetime brcmf_fw_alloc_request() is called once only during the probe. It's safe to assume provided array is clear. Further brcmfmac improvements may require calling it multiple times though. This patch allows it by fixing invalid firmware paths like: brcm/brcmfmac4366c-pcie.binbrcm/brcmfmac4366c-pcie.bin Signed-off-by:
-
Igor Mitsyanko authored
Use scan duration param for both active and passive scan dwell times. Document what different types of dwell times are used for. Explicitly specify that if unset, automatic selection by device firmware will be used. Signed-off-by:
Igor Mitsyanko <igor.mitsyanko.os@quantenna.com> Signed-off-by:
-
Igor Mitsyanko authored
Use control path to send EAPOL frames to make sure they are sent with higher priority with aggregation disabled. Signed-off-by:
-
Sergey Matyukevich authored
Allow to change netns for wireless interfaces created by qtnfmac driver. Signed-off-by:
Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by:
-
Sergey Matyukevich authored
This patch streamlines firmware state tracking. In particular, state QTNF_FW_STATE_FW_DNLD_DONE is removed, states QTNF_FW_STATE_RESET and QTNF_FW_STATE_DETACHED are merged into a single state. Besides, new state QTNF_FW_STATE_RUNNING is introduced to distinguish between the following two cases: - firmware load succeeded, firmware init process is ongoing - firmware init succeeded, firmware is fully functional Signed-off-by:
-
Sergey Matyukevich authored
Report that firmware is up and running only for successful firmware download. Simplify qtnf_pcie_fw_boot_done: modify error path so that no need to pass firmware dowload result to this function. Finally, do not create debugfs entries if firmware download succeeded, but core attach failed. Signed-off-by:
-
Igor Mitsyanko authored
In some regions, different regulatory limits (like max Tx power) may be defined for different operating modes. As an example: in ETSI regions DFS master devices may use higher transmit powers compared to DFS slave devices. Update bands information in CHANGE_INTF command if mode of operation changes. Signed-off-by:
-
Igor Mitsyanko authored
Pass DFS region as requested by regulatory core directly to firmware so it can initialize radar detection block accordingly. Signed-off-by:
-
Igor Mitsyanko authored
Currently driver uses the same regulatory rules to register all wiphy instances. This is not logically correct since each wiphy may have different capabilities (different supported bands, EIRP etc). Allow firmware to pass regulatory rules for each MAC separately. Signed-off-by:
-
Igor Mitsyanko authored
Use REGULATORY_CUSTOM_REG flag only if firmware advertised a custom regulatory domain prior to wiphy registration. Use REGULATORY_STRICT_REG flag only if firmware knows its regulatory domain. Signed-off-by:
-
Igor Mitsyanko authored
Currently only a portion of per-channel information is passed to firmware. Extend logic to pass all useful per-channel data. Signed-off-by:
-
Igor Mitsyanko authored
Before regulatory notifier is invoked by a wireless core, it will update band information for the wiphy. Pass this information to firmware together with new region alpha2 code. Signed-off-by:
-
Igor Mitsyanko authored
Error reporting in qtnf_cfg80211_reg_notifier only requires to print one type of message and an error code. Firmware will report success for an attempt to set regulatory region to the same value, so no special handling is required for this case. Signed-off-by:
-
Igor Mitsyanko authored
Wireless core calls regulatory notifier for each wiphy and it only guarantees that bands info is updated for this particular wiphy prior to calling a notifier. Hence updating all wiphy which belong to driver in a single notifier callback is redundant and incorrect. Signed-off-by:
-
- 30 Mar, 2019 1 commit
-
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2019-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next First batch of patches intended for v5.2 * Send NO_DATA events so they can be captured in radiotap; * Some channel-switch changes; * Support for multiple BSSID; * Continued work and bugfixes for the new debugging infra; * Support for some new FW API versions; * Some work to support new hardware; * General bugfixes; * Other cleanups;
-
- 29 Mar, 2019 17 commits
-
-
Julian Wiedmann authored
Replace the br_port_exists() macro with its twin from netdevice.h CC: Roopa Prabhu <roopa@cumulusnetworks.com> CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Acked-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Julian Wiedmann authored
Replace the team_port_exists() macro with its twin from netdevice.h CC: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Vishal Kulkarni authored
This patch advertises Forward Error Correction in ethtool Signed-off-by:
Casey Leedom <leedom@chelsio.com> Signed-off-by:
Vishal Kulkarni <vishal@chelsio.com> Signed-off-by:
-
Vishal Kulkarni authored
Change t4fw_version.h to update latest firmware version number to 1.23.3.0. Signed-off-by:
-
wenxu authored
There is currently no support for the multicast/broadcast aspects of VXLAN in ovs. In the datapath flow the tun_dst must specific. But in the IP_TUNNEL_INFO_BRIDGE mode the tun_dst can not be specific. And the packet can forward through the fdb table of vxlan devcice. In this mode the broadcast/multicast packet can be sent through the following ways in ovs. ovs-vsctl add-port br0 vxlan -- set in vxlan type=vxlan \ options:key=1000 options:remote_ip=flow ovs-ofctl add-flow br0 in_port=LOCAL,dl_dst=ff:ff:ff:ff:ff:ff, \ action=output:vxlan bridge fdb append ff:ff:ff:ff:ff:ff dev vxlan_sys_4789 dst 172.168.0.1 \ src_vni 1000 vni 1000 self bridge fdb append ff:ff:ff:ff:ff:ff dev vxlan_sys_4789 dst 172.168.0.2 \ src_vni 1000 vni 1000 self Signed-off-by:wenxu <wenxu@ucloud.cn> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
-
Eric Dumazet authored
TCP stack relies on the fact that a freshly allocated skb has skb->cb[] and skb_shinfo(skb)->tx_flags cleared. When recycling tx skb, we must ensure these fields are cleared. Fixes: 472c2e07 ("tcp: add one skb cache for tx") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
Boris Pismenny authored
The Innova IPsec driver is part of all Innova drivers, and its maintainenece is covered by an existing entry in this file. Signed-off-by:
Boris Pismenny <borisp@mellanox.com> Signed-off-by:
-
Dmytro Linkin authored
Add 36 pedit action tests to check pedit options described in tc-pedit(8) man page. Test cases can be specified by categories: actions, pedit, raw_op, layered_op. RAW_OP cases check offset option for u8, u16 and u32 offset size. LAYERED_OP cases check fields option for eth, ip, ip6, tcp and udp headers. Include following tests: 377e - Add pedit action with RAW_OP offset u32 a0ca - Add pedit action with RAW_OP offset u32 (INVALID) dd8a - Add pedit action with RAW_OP offset u16 u16 53db - Add pedit action with RAW_OP offset u16 (INVALID) 5c7e - Add pedit action with RAW_OP offset u8 add value 2893 - Add pedit action with RAW_OP offset u8 quad 3a07 - Add pedit action with RAW_OP offset u8-u16-u8 ab0f - Add pedit action with RAW_OP offset u16-u8-u8 9d12 - Add pedit action with RAW_OP offset u32 set u16 clear u8 invert ebfa - Add pedit action with RAW_OP offset overflow u32 (INVALID) f512 - Add pedit action with RAW_OP offset u16 at offmask shift set c2cb - Add pedit action with RAW_OP offset u32 retain value 86d4 - Add pedit action with LAYERED_OP eth set src & dst c715 - Add pedit action with LAYERED_OP eth set src (INVALID) ba22 - Add pedit action with LAYERED_OP eth type set/clear sequence 5810 - Add pedit action with LAYERED_OP ip set src & dst 1092 - Add pedit action with LAYERED_OP ip set ihl & dsfield 02d8 - Add pedit action with LAYERED_OP ip set ttl & protocol 3e2d - Add pedit action with LAYERED_OP ip set ttl (INVALID) 31ae - Add pedit action with LAYERED_OP ip ttl clear/set 486f - Add pedit action with LAYERED_OP ip set duplicate fields e790 - Add pedit action with LAYERED_OP ip set ce, df, mf, firstfrag, nofrag fields 6829 - Add pedit action with LAYERED_OP beyond ip set dport & sport afd8 - Add pedit action with LAYERED_OP beyond ip set icmp_type & icmp_code 3143 - Add pedit action with LAYERED_OP beyond ip set dport (INVALID) fc1f - Add pedit action with LAYERED_OP ip6 set src & dst 6d34 - Add pedit action with LAYERED_OP ip6 dst retain value (INVALID) 6f5e - Add pedit action with LAYERED_OP ip6 flow_lbl 6795 - Add pedit action with LAYERED_OP ip6 set payload_len, nexthdr, hoplimit 1442 - Add pedit action with LAYERED_OP tcp set dport & sport b7ac - Add pedit action with LAYERED_OP tcp sport set (INVALID) cfcc - Add pedit action with LAYERED_OP tcp flags set 3bc4 - Add pedit action with LAYERED_OP tcp set dport, sport & flags fields f1c8 - Add pedit action with LAYERED_OP udp set dport & sport d784 - Add pedit action with mixed RAW/LAYERED_OP #1 70ca - Add pedit action with mixed RAW/LAYERED_OP #2 Signed-off-by:
Dmytro Linkin <dmitrolin@mellanox.com> Signed-off-by:
-
David Ahern authored
The number of stubs is growing and has nothing to do with addrconf. Move the definition of the stubs to a separate header file and update users. In the move, drop the vxlan specific comment before ipv6_stub. Code move only; no functional change intended. Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David S. Miller authored
David Ahern says: ==================== net: Move fib_nh and fib6_nh to a common struct First set of three with the end goal of enabling IPv6 gateways with IPv4 routes. This set refactors ipv4 and ipv6 code to create init and release helpers for each protocol and moving common elements to a fib_nh_common struct. v3 - split the reject setting into 2 with helper to the checks. This avoids changing cfg->fc_flags in fib6_nh_init v2 - addressed Ido's comments: cleanup on failure path in nh_init helpers, ordering in fib6_nh_release, and removal of RTF_GATEWAY from fib6_info uses in mlxsw ==================== Signed-off-by: -
David Ahern authored
With fib_nh_common in place, move common initialization and release code into helpers used by both ipv4 and ipv6. For the moment, the init is just the lwt encap and the release is both the netdev reference and the the lwt state reference. More will be added later. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
David Ahern authored
Add fib_nh_common struct with common nexthop attributes. Convert fib_nh and fib6_nh to use it. Use macros to move existing fib_nh_* references to the new nh_common.nhc_*. Signed-off-by:
-
David Ahern authored
Rename fib6_nh entries that will be moved to a fib_nh_common struct. Specifically, the device, gateway, flags, and lwtstate are common with all nexthop definitions. In some places new temporary variables are declared or local variables renamed to maintain line lengths. Rename only; no functional change intended. Signed-off-by:
-
David Ahern authored
Rename fib_nh entries that will be moved to a fib_nh_common struct. Specifically, the device, oif, gateway, flags, scope, lwtstate, nh_weight and nh_upper_bound are common with all nexthop definitions. In the process shorten fib_nh_lwtstate to fib_nh_lws to avoid really long lines. Rename only; no functional change intended. Signed-off-by:
-
David Ahern authored
rt6_add_nexthop and rt6_nexthop_info only need the fib6_info for the gateway flag and the nexthop weight, and the presence of a gateway is now per-nexthop. Update the signatures to take a fib6_nh and nexthop weight and better align with the ipv4 versions. Signed-off-by:
-
David Ahern authored
fib6_ignore_linkdown takes a fib6_info but only looks at the net_device and its IPv6 config. Change it to take a net_device over a fib6_info as its input argument. In addition, move it to a header file to make the check inline and usable later with IPv4 code without going through the ipv6 stub, and rename to ip6_ignore_linkdown since it is only checking the setting based on the ipv6 struct on a device. Signed-off-by:
-
David Ahern authored
The gateway setting is not per fib6_info entry but per-fib6_nh. Add a new fib_nh_has_gw flag to fib6_nh and convert references to RTF_GATEWAY to the new flag. For IPv6 address the flag is cheaper than checking that nh_gw is non-0 like IPv4 does. While this increases fib6_nh by 8-bytes, the effective allocation size of a fib6_info is unchanged. The 8 bytes is recovered later with a fib_nh_common change. Signed-off-by:
-
