name pins consistently (MIC1/LINE1/HP-OUT/CD) on all controls
affecting those pins.

remove duplicate SET_AMP_GAIN_MUTE to 0x17/index 0 and 0x17/index 1

really select MIC1, not Mixer out for recording

"Mixer out" for recording is not a "pin", adjust comment
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

CX20549 (ctx5045) doesn't accept data on index 1 for output pins,
as shown in the following hda-var transaction:

  $ hda-verb /dev/snd/hwC0D0 0x10 set_amp_gain 0xb126
  nid = 0x10, verb = 0x300, param = 0xb126
  value = 0x0
  $ hda-verb /dev/snd/hwC0D0 0x10 get_amp_gain 0x8001
  nid = 0x10, verb = 0xb00, param = 0x8001
  value = 0x0
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The ID used for detection of the BenQ R55E actually identifies the
Quanta TW3 ODM design, which is also used for the Gigabyte W551 laptop
series. Schematics on the internet clearly indicate that the "Port C"
(analog input connected to record source #4 and mixer input #4) is
unconnected.

Playing an audio CD through analog playback (using cdplay from cdtools)
produces no sound, even with the mixer input labelled "CD" enabled, and
the volume control in the CD drive set to maximum. This indicates the
connection is really not present.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The "input converter" widget of the CX20459 has only one input amplifier,
expose that one as "Capture Volume/Capture Switch". The actual record
source selection is already exposed through the separately installed
input mux.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This includes renaming "Line In" to line, also in the mixer settings.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The CX20549 has only one single input amp on it's input converter
widget. Fix printing of values in the codec file in /proc/asound.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Make this function consistent with others in this module by
returning 1 for error, instead of -ENOMEM
(reverts function signature change from a938fb1e)
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fix module parameter data type to eliminate build warnings.

sound/isa/opti9xx/opti92x-ad1848.c:87:1: warning: return from incompatible pointer type
sound/isa/opti9xx/opti92x-ad1848.c:87:1: warning: return from incompatible pointer type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fix module parameter data type to eliminate build warning.

sound/oss/msnd_pinnacle.c:1727:1: warning: return from incompatible pointer type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ASoC: A few more updates for 3.4

The cleanup of the dmaengine parameter messup and a tweak to some
callibration values for WM1811.

This function returns zero or -ENOMEM, but because it's type is u16, the
-ENOMEM gets changed to 65524.  None of the callers care, but lets fix
it anyway as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

commit 4a163c82 added extra parameter to device_prep_dma_cyclic
this is not required if we use the wrapper over cyclic API.

This is split from Alexedre's patch
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since commit 185ecb5f (dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic)
prep_dma_cyclic() got an extra context parameter.

Add this new parameter in order to fix the following build error (mxs_defconfig and imx_v4_v5_defconfig):

sound/soc/soc-dmaengine-pcm.c:149:3: error: too few arguments to function 'chan->device->device_prep_dma_cyclic'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The recent Realtek driver tries to assign an extra input via the
headphone plug when only a single input source is found.  The code
worked on Samsung Q1, but it broke ASUS 1015 where the mic is a
digital-mic and only a specific ADC works.

This patch fixes the assignment of ADC in the shared mic/hp case.
Instead of assuming the single ADC at first, reduce the ADCs after
trying to assign both mic and HP pins.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42973

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Based on latest production information.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Last minute ASoC updates for 3.4

There's a couple of small features here that were added late on but have
been in -next in my tree and some bug fixes.  The wm_hubs stuff is
actually bug fixes - the stuff that's currently in 3.4 is a half way
house between the two solutions that the latest change allows the
machine to select between.

The optimal management of VMID depends on a number of factors which vary
dynamically at runtime, for example the connection to a system docking
station. In some circumstances it is desirable to keep VMID enabled all
the time, in others it is desirable to aggressively power it up and down.

Provide a callback allowing machine driver to configure either the normal
power up/down mode (WM8994_VMID_MODE_NORMAL) or to maintain VMID even
when idle (WM8994_VMID_MODE_FORCE). This callback, wm8994_vmid_mode(),
should be called with the CODEC lock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

It can just be enabled all the time with no impact.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

PXA's SSP engine fails to take its current channel phase into account
when enabling a stream while the engine is already running. This
results in randomly swapped left/right channels on either the record
or the playback side, depending on which one was enabled first.

The following patch fixes this by factoring out the bit field
modifications in question to a separate function that pauses the
engine temporarily, modifies the bits and kicks it off again
afterwards. Appearantly, a transition of SSCR0_SSE syncs both
directions properly.

The patch has been rolled out to quite a number of devices over the
last weeks and seems to fix the issue reliably.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The WM8776 codec driver requires the machine driver to set one of the
SND_SOC_DAIFMT_CBx_xxx values.  The P1022DS machine driver should be setting
SND_SOC_DAIFMT_CBM_CFM, but since that value was zero, no one noticed.

Commit 75d9ac46 ("ASoC: Allow DAI formats to be specified in the
dai_link"), however, changed the value of SND_SOC_DAIFMT_CBM_CFM from zero
to a non-zero value, which means that it now needs to be specifically set
by the machine driver.

We also set SND_SOC_DAIFMT_NB_NF, for the same reason.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The dma size will be changed by requested number of
channel(mono/stereo) from platform. For mono recording,
channels_min value should be 1.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

The irq handler must check whether the MPU401 instance is still alive.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

We're currently not freeing card->rtd in cases where the card is
unregistered before being instantiated - convert it to devm_kzalloc() to
make sure that happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Linus decided to go for another week so here's a few more updates - a
mixed bag here, a few minor diagnostic tweaks, some driver enhancements
and the dmaengine conversion for ep93xx drivers which was tested a while
ago and just waiting for a signoff.

GFP_ATOMIC is used in snd_pcm_link() just because the kmalloc is
called inside a lock.  Since this function isn't too critical for
speed and is rarely called in practice, better to allocate the chunk
at first before spinlock and free it in error paths, so that
GFP_KERNEL can be used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Allows the constraint lists to be declared const by drivers which seems
reasonable; there's plenty of other constification we could do if we were
being complete but this was easy and quick.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The WM8996 specification has been updated to specify 44.1kHz as a supported
sample rate. Update the driver to accept this configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Now the mute-LED is controlled without powersave hack, and the ifdefs must
be removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Convert mx27vis-aic32x4 to platform driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

A previous commit af65cbf2 (ALSA: hdmi: fix printout of SAD sampling
rates) fixed the sample rates shown in /proc/asound/cardX/eldY and
kernel log to not be entirely wrong. However, a missing rate from the
array added in the patch causes HDMI rates 88.2 kHz, 96 kHz, 176.4 kHz,
and 192 kHz to be shown as 96 kHz, 176.4 kHz, 192 kHz, and 384 kHz,
respectively.

Fix the reporting by adding the ALSA rate 64 kHz into the conversion
array between 48 kHz and 88.2 kHz.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We need to resume two legacy registers to recover MIDI/FM functionality
on S3/S4 resume, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fixed a trailing white space error detected
in sound/core/control.c by checkpatch.pl script.
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Since it's not always safe to assume that the vmaster hook is purely the
mute-LED control, add the flag indicating whether to expose the mute-LED
enum control or not.  Currently, conexant codec sets this off for non-HP
laptops where EAPD may be used really as EAPD.
Signed-off-by: Takashi Iwai <tiwai@suse.de>