[ Upstream commit 7596175e ]

In case of IPv6 pkts, ipv4_csum_ok is 0. Because of this, driver does
not set skb->ip_summed. So IPv6 rx checksum is not offloaded.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9b1f19d8 ]

Similarly to commit 276bdb82 ("dccp: check ccid before dereferencing")
it is wise to test for a NULL ccid.

kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.0.0-rc3+ #37
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:ccid_hc_tx_parse_options net/dccp/ccid.h:205 [inline]
RIP: 0010:dccp_parse_options+0x8d9/0x12b0 net/dccp/options.c:233
Code: c5 0f b6 75 b3 80 38 00 0f 85 d6 08 00 00 48 b9 00 00 00 00 00 fc ff df 48 8b 45 b8 4c 8b b8 f8 07 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 08 00 0f 85 95 08 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b
kobject: 'loop5' (0000000080f78fc1): kobject_uevent_env
RSP: 0018:ffff8880a94df0b8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8880858ac723 RCX: dffffc0000000000
RDX: 0000000000000100 RSI: 0000000000000007 RDI: 0000000000000001
RBP: ffff8880a94df140 R08: 0000000000000001 R09: ffff888061b83a80
R10: ffffed100c370752 R11: ffff888061b83a97 R12: 0000000000000026
R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff8880ae700000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f0defa33518 CR3: 000000008db5e000 CR4: 00000000001406e0
kobject: 'loop5' (0000000080f78fc1): fill_kobj_path: path = '/devices/virtual/block/loop5'
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 dccp_rcv_state_process+0x2b6/0x1af6 net/dccp/input.c:654
 dccp_v4_do_rcv+0x100/0x190 net/dccp/ipv4.c:688
 sk_backlog_rcv include/net/sock.h:936 [inline]
 __sk_receive_skb+0x3a9/0xea0 net/core/sock.c:473
 dccp_v4_rcv+0x10cb/0x1f80 net/dccp/ipv4.c:880
 ip_protocol_deliver_rcu+0xb6/0xa20 net/ipv4/ip_input.c:208
 ip_local_deliver_finish+0x23b/0x390 net/ipv4/ip_input.c:234
 NF_HOOK include/linux/netfilter.h:289 [inline]
 NF_HOOK include/linux/netfilter.h:283 [inline]
 ip_local_deliver+0x1f0/0x740 net/ipv4/ip_input.c:255
 dst_input include/net/dst.h:450 [inline]
 ip_rcv_finish+0x1f4/0x2f0 net/ipv4/ip_input.c:414
 NF_HOOK include/linux/netfilter.h:289 [inline]
 NF_HOOK include/linux/netfilter.h:283 [inline]
 ip_rcv+0xed/0x620 net/ipv4/ip_input.c:524
 __netif_receive_skb_one_core+0x160/0x210 net/core/dev.c:4973
 __netif_receive_skb+0x2c/0x1c0 net/core/dev.c:5083
 process_backlog+0x206/0x750 net/core/dev.c:5923
 napi_poll net/core/dev.c:6346 [inline]
 net_rx_action+0x76d/0x1930 net/core/dev.c:6412
 __do_softirq+0x30b/0xb11 kernel/softirq.c:292
 run_ksoftirqd kernel/softirq.c:654 [inline]
 run_ksoftirqd+0x8e/0x110 kernel/softirq.c:646
 smpboot_thread_fn+0x6ab/0xa10 kernel/smpboot.c:164
 kthread+0x357/0x430 kernel/kthread.c:246
 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Modules linked in:
---[ end trace 58a0ba03bea2c376 ]---
RIP: 0010:ccid_hc_tx_parse_options net/dccp/ccid.h:205 [inline]
RIP: 0010:dccp_parse_options+0x8d9/0x12b0 net/dccp/options.c:233
Code: c5 0f b6 75 b3 80 38 00 0f 85 d6 08 00 00 48 b9 00 00 00 00 00 fc ff df 48 8b 45 b8 4c 8b b8 f8 07 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 08 00 0f 85 95 08 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b
RSP: 0018:ffff8880a94df0b8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8880858ac723 RCX: dffffc0000000000
RDX: 0000000000000100 RSI: 0000000000000007 RDI: 0000000000000001
RBP: ffff8880a94df140 R08: 0000000000000001 R09: ffff888061b83a80
R10: ffffed100c370752 R11: ffff888061b83a97 R12: 0000000000000026
R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff8880ae700000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f0defa33518 CR3: 0000000009871000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 03334ba8 upstream.

Avoid warnings like this:
thermal_hwmon.h:29:1: warning: ‘thermal_remove_hwmon_sysfs’ defined but not used [-Wunused-function]
 thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz)

Fixes: 0dd88793 ("thermal: hwmon: move hwmon support to single file")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b058809b ]

A bug is present in GDB which causes early string termination when
parsing variables.  This has been reported [0], but we should ensure
that we can support at least basic printing of the core kernel strings.

For current gdb version (has been tested with 7.3 and 8.1), 'lx-version'
only prints one character.

  (gdb) lx-version
  L(gdb)

This can be fixed by casting 'linux_banner' as (char *).

  (gdb) lx-version
  Linux version 4.19.0-rc1+ (changbin@acer) (gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3)) #21 SMP Sat Sep 1 21:43:30 CST 2018

[0] https://sourceware.org/bugzilla/show_bug.cgi?id=20077

[kbingham@kernel.org: add detail to commit message]
Link: http://lkml.kernel.org/r/20181111162035.8356-1-kieran.bingham@ideasonboard.com
Fixes: 2d061d99 ("scripts/gdb: add version command")
Signed-off-by: Du Changbin <changbin.du@gmail.com>
Signed-off-by: Kieran Bingham <kbingham@kernel.org>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8099b047 ]

load_script() simply truncates bprm->buf and this is very wrong if the
length of shebang string exceeds BINPRM_BUF_SIZE-2.  This can silently
truncate i_arg or (worse) we can execute the wrong binary if buf[2:126]
happens to be the valid executable path.

Change load_script() to return ENOEXEC if it can't find '\n' or zero in
bprm->buf.  Note that '\0' can come from either
prepare_binprm()->memset() or from kernel_read(), we do not care.

Link: http://lkml.kernel.org/r/20181112160931.GA28463@redhat.comSigned-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Ben Woodard <woodard@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 76699a67 ]

The ep->ovflist is a secondary ready-list to temporarily store events
that might occur when doing sproc without holding the ep->wq.lock.  This
accounts for every time we check for ready events and also send events
back to userspace; both callbacks, particularly the latter because of
copy_to_user, can account for a non-trivial time.

As such, the unlikely() check to see if the pointer is being used, seems
both misleading and sub-optimal.  In fact, we go to an awful lot of
trouble to sync both lists, and populating the ovflist is far from an
uncommon scenario.

For example, profiling a concurrent epoll_wait(2) benchmark, with
CONFIG_PROFILE_ANNOTATED_BRANCHES shows that for a two threads a 33%
incorrect rate was seen; and when incrementally increasing the number of
epoll instances (which is used, for example for multiple queuing load
balancing models), up to a 90% incorrect rate was seen.

Similarly, by deleting the prediction, 3% throughput boost was seen
across incremental threads.

Link: http://lkml.kernel.org/r/20181108051006.18751-4-dave@stgolabs.netSigned-off-by: Davidlohr Bueso <dbueso@suse.de>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jason Baron <jbaron@akamai.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 168e06f7 ]

Based on commit 401c636a ("kernel/hung_task.c: show all hung tasks
before panic"), we could get the call stack of hung task.

However, if the console loglevel is not high, we still can not see the
useful panic information in practice, and in most cases users don't set
console loglevel to high level.

This patch is to force console verbose before system panic, so that the
real useful information can be seen in the console, instead of being
like the following, which doesn't have hung task information.

  INFO: task init:1 blocked for more than 120 seconds.
        Tainted: G     U  W         4.19.0-quilt-2e5dc0ac-g51b6c21d76cc #1
  "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
  Kernel panic - not syncing: hung_task: blocked tasks
  CPU: 2 PID: 479 Comm: khungtaskd Tainted: G     U  W         4.19.0-quilt-2e5dc0ac-g51b6c21d76cc #1
  Call Trace:
   dump_stack+0x4f/0x65
   panic+0xde/0x231
   watchdog+0x290/0x410
   kthread+0x12c/0x150
   ret_from_fork+0x35/0x40
  reboot: panic mode set: p,w
  Kernel Offset: 0x34000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)

Link: http://lkml.kernel.org/r/27240C0AC20F114CBF8149A2696CBE4A6015B675@SHSMSX101.ccr.corp.intel.comSigned-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 09be1784 ]

If the number of input parameters is less than the total parameters, an
EINVAL error will be returned.

For example, we use proc_doulongvec_minmax to pass up to two parameters
with kern_table:

{
	.procname       = "monitor_signals",
	.data           = &monitor_sigs,
	.maxlen         = 2*sizeof(unsigned long),
	.mode           = 0644,
	.proc_handler   = proc_doulongvec_minmax,
},

Reproduce:

When passing two parameters, it's work normal.  But passing only one
parameter, an error "Invalid argument"(EINVAL) is returned.

  [root@cl150 ~]# echo 1 2 > /proc/sys/kernel/monitor_signals
  [root@cl150 ~]# cat /proc/sys/kernel/monitor_signals
  1       2
  [root@cl150 ~]# echo 3 > /proc/sys/kernel/monitor_signals
  -bash: echo: write error: Invalid argument
  [root@cl150 ~]# echo $?
  1
  [root@cl150 ~]# cat /proc/sys/kernel/monitor_signals
  3       2
  [root@cl150 ~]#

The following is the result after apply this patch.  No error is
returned when the number of input parameters is less than the total
parameters.

  [root@cl150 ~]# echo 1 2 > /proc/sys/kernel/monitor_signals
  [root@cl150 ~]# cat /proc/sys/kernel/monitor_signals
  1       2
  [root@cl150 ~]# echo 3 > /proc/sys/kernel/monitor_signals
  [root@cl150 ~]# echo $?
  0
  [root@cl150 ~]# cat /proc/sys/kernel/monitor_signals
  3       2
  [root@cl150 ~]#

There are three processing functions dealing with digital parameters,
__do_proc_dointvec/__do_proc_douintvec/__do_proc_doulongvec_minmax.

This patch deals with __do_proc_doulongvec_minmax, just as
__do_proc_dointvec does, adding a check for parameters 'left'.  In
__do_proc_douintvec, its code implementation explicitly does not support
multiple inputs.

static int __do_proc_douintvec(...){
         ...
         /*
          * Arrays are not supported, keep this simple. *Do not* add
          * support for them.
          */
         if (vleft != 1) {
                 *lenp = 0;
                 return -EINVAL;
         }
         ...
}

So, just __do_proc_doulongvec_minmax has the problem.  And most use of
proc_doulongvec_minmax/proc_doulongvec_ms_jiffies_minmax just have one
parameter.

Link: http://lkml.kernel.org/r/1544081775-15720-1-git-send-email-cheng.lin130@zte.com.cnSigned-off-by: Cheng Lin <cheng.lin130@zte.com.cn>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 304ae427 ]

check_hung_uninterruptible_tasks() is currently calling rcu_lock_break()
for every 1024 threads.  But check_hung_task() is very slow if printk()
was called, and is very fast otherwise.

If many threads within some 1024 threads called printk(), the RCU grace
period might be extended enough to trigger RCU stall warnings.
Therefore, calling rcu_lock_break() for every some fixed jiffies will be
safer.

Link: http://lkml.kernel.org/r/1544800658-11423-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jpSigned-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6ae16dfb ]

In lenovo_probe_tpkbd(), the function of_led_classdev_register() could
return an error value that is unchecked. The fix adds these checks.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9d216211 ]

First correct the edge case to return the last element if we're
outside the range, rather than at the last element, so that
interpolation is not omitted for points between the two last entries in
the table.

Then correct the formula to perform linear interpolation based the two
points surrounding the read ADC value. The indices for temp are kept as
"hi" and "lo" to pair with the adc indices, but there's no requirement
that the temperature is provided in descendent order. mult_frac() is
used to prevent issues with overflowing the int.

Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 162bc7f5 ]

If you have a CPU that fails to round up and then run 'btc' you'll end
up crashing in kdb becaue we dereferenced NULL.  Let's add a check.
It's wise to also set the task to NULL when leaving the debugger so
that if we fail to round up on a later entry into the debugger we
won't backtrace a stale task.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d56c19d0 ]

By defaul of-based thermal driver do not enable hwmon.
This patch does this explicitly, so that the temperature can be read
through the common hwmon sysfs.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 296dcc40 ]

When the block device is opened with FMODE_EXCL, ref_count is set to -1.
This value doesn't get reset when the device is closed which means the
device cannot be opened again. Fix this by checking for refcount <= 0
in the release method.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0d9c9a23 ]

These functions are called from atomic context:

[    9.150239] BUG: sleeping function called from invalid context at /home/scott/git/linux/mm/slab.h:421
[    9.158159] in_atomic(): 1, irqs_disabled(): 0, pid: 4432, name: ip
[    9.163128] CPU: 8 PID: 4432 Comm: ip Not tainted 4.20.0-rc2-00169-g63d86876 #29
[    9.163130] Call Trace:
[    9.170701] [c0000002e899a980] [c0000000009c1068] .dump_stack+0xa8/0xec (unreliable)
[    9.177140] [c0000002e899aa10] [c00000000007a7b4] .___might_sleep+0x138/0x164
[    9.184440] [c0000002e899aa80] [c0000000001d5bac] .kmem_cache_alloc_trace+0x238/0x30c
[    9.191216] [c0000002e899ab40] [c00000000065ea1c] .memac_add_hash_mac_address+0x104/0x198
[    9.199464] [c0000002e899abd0] [c00000000065a788] .set_multi+0x1c8/0x218
[    9.206242] [c0000002e899ac80] [c0000000006615ec] .dpaa_set_rx_mode+0xdc/0x17c
[    9.213544] [c0000002e899ad00] [c00000000083d2b0] .__dev_set_rx_mode+0x80/0xd4
[    9.219535] [c0000002e899ad90] [c00000000083d334] .dev_set_rx_mode+0x30/0x54
[    9.225271] [c0000002e899ae10] [c00000000083d4a0] .__dev_open+0x148/0x1c8
[    9.230751] [c0000002e899aeb0] [c00000000083d934] .__dev_change_flags+0x19c/0x1e0
[    9.230755] [c0000002e899af60] [c00000000083d9a4] .dev_change_flags+0x2c/0x80
[    9.242752] [c0000002e899aff0] [c0000000008554ec] .do_setlink+0x350/0xf08
[    9.248228] [c0000002e899b170] [c000000000857ad0] .rtnl_newlink+0x588/0x7e0
[    9.253965] [c0000002e899b740] [c000000000852424] .rtnetlink_rcv_msg+0x3e0/0x498
[    9.261440] [c0000002e899b820] [c000000000884790] .netlink_rcv_skb+0x134/0x14c
[    9.267607] [c0000002e899b8e0] [c000000000851840] .rtnetlink_rcv+0x18/0x2c
[    9.274558] [c0000002e899b950] [c000000000883c8c] .netlink_unicast+0x214/0x318
[    9.281163] [c0000002e899ba00] [c000000000884220] .netlink_sendmsg+0x348/0x444
[    9.287076] [c0000002e899bae0] [c00000000080d13c] .sock_sendmsg+0x2c/0x54
[    9.287080] [c0000002e899bb50] [c0000000008106c0] .___sys_sendmsg+0x2d0/0x2d8
[    9.298375] [c0000002e899bd30] [c000000000811a80] .__sys_sendmsg+0x5c/0xb0
[    9.303939] [c0000002e899be20] [c0000000000006b0] system_call+0x60/0x6c
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 093c4821 ]

In probe_gdrom(), the buffer pointed by 'gd.cd_info' is allocated through
kzalloc() and is used to hold the information of the gdrom device. To
register and unregister the device, the pointer 'gd.cd_info' is passed to
the functions register_cdrom() and unregister_cdrom(), respectively.
However, this buffer is not freed after it is used, which can cause a
memory leak bug.

This patch simply frees the buffer 'gd.cd_info' in exit_gdrom() to fix the
above issue.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7418e652 ]

In drivers/isdn/hisax/hfc_pci.c, the functions hfcpci_interrupt() and
HFCPCI_l1hw() may be concurrently executed.

HFCPCI_l1hw()
  line 1173: if (!cs->tx_skb)

hfcpci_interrupt()
  line 942: spin_lock_irqsave();
  line 1066: dev_kfree_skb_irq(cs->tx_skb);

Thus, a possible concurrency use-after-free bug may occur
in HFCPCI_l1hw().

To fix these bugs, the calls to spin_lock_irqsave() and
spin_unlock_irqrestore() are added in HFCPCI_l1hw(), to protect the
access to cs->tx_skb.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9e6aea22 ]

Included file path was hard-wired in the ocfs2 makefile, which might
causes some confusion when compiling ocfs2 as an external module.

Say if we compile ocfs2 module as following.
cp -r /kernel/tree/fs/ocfs2 /other/dir/ocfs2
cd /other/dir/ocfs2
make -C /path/to/kernel_source M=`pwd` modules

Acutally, the compiler wil try to find included file in
/kernel/tree/fs/ocfs2, rather than the directory /other/dir/ocfs2.

To fix this little bug, we introduce the var $(src) provided by kbuild.
$(src) means the absolute path of the running kbuild file.

Link: http://lkml.kernel.org/r/20181108085546.15149-1-lchen@suse.comSigned-off-by: Larry Chen <lchen@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 70306d9d ]

For sync io read in ocfs2_read_blocks_sync(), first clear bh uptodate flag
and submit the io, second wait io done, last check whether bh uptodate, if
not return io error.

If two sync io for the same bh were issued, it could be the first io done
and set uptodate flag, but just before check that flag, the second io came
in and cleared uptodate, then ocfs2_read_blocks_sync() for the first io
will return IO error.

Indeed it's not necessary to clear uptodate flag, as the io end handler
end_buffer_read_sync() will set or clear it based on io succeed or failed.

The following message was found from a nfs server but the underlying
storage returned no error.

[4106438.567376] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2780 ERROR: read block 1238823695 failed -5
[4106438.567569] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2812 ERROR: status = -5
[4106438.567611] (nfsd,7146,3):ocfs2_test_inode_bit:2894 ERROR: get alloc slot and bit failed -5
[4106438.567643] (nfsd,7146,3):ocfs2_test_inode_bit:2932 ERROR: status = -5
[4106438.567675] (nfsd,7146,3):ocfs2_get_dentry:94 ERROR: test inode bit failed -5

Same issue in non sync read ocfs2_read_blocks(), fixed it as well.

Link: http://lkml.kernel.org/r/20181121020023.3034-4-junxiao.bi@oracle.comSigned-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Changwei Ge <ge.changwei@h3c.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 67a28de4 ]

Running something like:

	decodecode vmlinux .

leads to interested results where not only the leading "." gets stripped
from the displayed paths, but also anywhere in the string, displaying
something like:

	kvm_vcpu_check_block (arch/arm64/kvm/virt/kvm/kvm_mainc:2141)

which doesn't help further processing.

Fix it by only stripping the base path if it is a prefix of the path.

Link: http://lkml.kernel.org/r/20181210174659.31054-3-marc.zyngier@arm.comSigned-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e250d91d ]

This fixes the case where all mount options specified are consumed by an
LSM and all that's left is an empty string. In this case cgroupfs should
accept the string and not fail.

How to reproduce (with SELinux enabled):

    # umount /sys/fs/cgroup/unified
    # mount -o context=system_u:object_r:cgroup_t:s0 -t cgroup2 cgroup2 /sys/fs/cgroup/unified
    mount: /sys/fs/cgroup/unified: wrong fs type, bad option, bad superblock on cgroup2, missing codepage or helper program, or other error.
    # dmesg | tail -n 1
    [   31.575952] cgroup: cgroup2: unknown option ""

Fixes: 67e9c74b ("cgroup: replace __DEVEL__sane_behavior with cgroup2 fs type")
[NOTE: should apply on top of commit 5136f636 ("cgroup: implement "nsdelegate" mount option"), older versions need manual rebase]
Suggested-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e4589fa5 ]

When there is a failure in f2fs_fill_super() after/during
the recovery of fsync'd nodes, it frees the current sbi and
retries again. This time the mount is successful, but the files
that got recovered before retry, still holds the extent tree,
whose extent nodes list is corrupted since sbi and sbi->extent_list
is freed up. The list_del corruption issue is observed when the
file system is getting unmounted and when those recoverd files extent
node is being freed up in the below context.

list_del corruption. prev->next should be fffffff1e1ef5480, but was (null)
<...>
kernel BUG at kernel/msm-4.14/lib/list_debug.c:53!
lr : __list_del_entry_valid+0x94/0xb4
pc : __list_del_entry_valid+0x94/0xb4
<...>
Call trace:
__list_del_entry_valid+0x94/0xb4
__release_extent_node+0xb0/0x114
__free_extent_tree+0x58/0x7c
f2fs_shrink_extent_tree+0xdc/0x3b0
f2fs_leave_shrinker+0x28/0x7c
f2fs_put_super+0xfc/0x1e0
generic_shutdown_super+0x70/0xf4
kill_block_super+0x2c/0x5c
kill_f2fs_super+0x44/0x50
deactivate_locked_super+0x60/0x8c
deactivate_super+0x68/0x74
cleanup_mnt+0x40/0x78
__cleanup_mnt+0x1c/0x28
task_work_run+0x48/0xd0
do_notify_resume+0x678/0xe98
work_pending+0x8/0x14

Fix this by not creating extents for those recovered files if shrinker is
not registered yet. Once mount is successful and shrinker is registered,
those files can have extents again.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 26fd962b ]

niu_pci_eeprom_read() may fail, so we should check its return value
before using the read data.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8892d854 ]

Changing protection is a very high cost operation in UML
because in addition to an extra syscall it also interrupts
mmap merge sequences generated by the tlb.

While the condition is not particularly common it is worth
avoiding.
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 59a63e47 ]

RHBZ: 1021460

There is an issue where when multiple threads open/close the same directory
ntwrk_buf_start might end up being NULL, causing the call to smbCalcSize
later to oops with a NULL deref.

The real bug is why this happens and why this can become NULL for an
open cfile, which should not be allowed.
This patch tries to avoid a oops until the time when we fix the underlying
issue.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0b153944 ]

Testing has shown, that when using mainline U-Boot on MT7688 based
boards, the system may hang or crash while mounting the root-fs. The
main issue here is that mainline U-Boot configures EBase to a value
near the end of system memory. And with CONFIG_CPU_MIPSR2_IRQ_VI
disabled, trap_init() will not allocate a new area to place the
exception handler. The original value will be used and the handler
will be copied to this location, which might already be used by some
userspace application.

The MT7688 supports VI - its config3 register is 0x00002420, so VInt
(Bit 5) is set. But without setting CONFIG_CPU_MIPSR2_IRQ_VI this
bit will not be evaluated to result in "cpu_has_vi" being set. This
patch now selects CONFIG_CPU_MIPSR2_IRQ_VI on MT7620/8 which results
trap_init() to allocate some memory for the exception handler.

Please note that this issue was not seen with the Mediatek U-Boot
version, as it does not touch EBase (stays at default of 0x8000.0000).
This is strictly also not correct as the kernel (_text) resides
here.
Signed-off-by: Stefan Roese <sr@denx.de>
[paul.burton@mips.com: s/beeing/being/]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5ac93f80 ]

Clang warns when one enumerated type is implicitly converted to another:

drivers/crypto/ux500/hash/hash_core.c:169:4: warning: implicit
conversion from enumeration type 'enum dma_data_direction' to different
enumeration type 'enum dma_transfer_direction' [-Wenum-conversion]
                        direction, DMA_CTRL_ACK | DMA_PREP_INTERRUPT);
                        ^~~~~~~~~
1 warning generated.

dmaengine_prep_slave_sg expects an enum from dma_transfer_direction.
We know that the only direction supported by this function is
DMA_TO_DEVICE because of the check at the top of this function so we can
just use the equivalent value from dma_transfer_direction.

DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9d880c59 ]

Clang warns when one enumerated type is implicitly converted to another:

drivers/crypto/ux500/cryp/cryp_core.c:559:5: warning: implicit
conversion from enumeration type 'enum dma_data_direction' to different
enumeration type 'enum dma_transfer_direction' [-Wenum-conversion]
                                direction, DMA_CTRL_ACK);
                                ^~~~~~~~~
drivers/crypto/ux500/cryp/cryp_core.c:583:5: warning: implicit
conversion from enumeration type 'enum dma_data_direction' to different
enumeration type 'enum dma_transfer_direction' [-Wenum-conversion]
                                direction,
                                ^~~~~~~~~
2 warnings generated.

dmaengine_prep_slave_sg expects an enum from dma_transfer_direction.
Because we know the value of the dma_data_direction enum from the
switch statement, we can just use the proper value from
dma_transfer_direction so there is no more conversion.

DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1
DMA_FROM_DEVICE = DMA_DEV_TO_MEM = 2
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0464ed24 ]

Currently seq_buf_puts() will happily create a non null-terminated
string for you in the buffer. This is particularly dangerous if the
buffer is on the stack.

For example:

  char buf[8];
  char secret = "secret";
  struct seq_buf s;

  seq_buf_init(&s, buf, sizeof(buf));
  seq_buf_puts(&s, "foo");
  printk("Message is %s\n", buf);

Can result in:

  Message is fooªªªªªsecret

We could require all users to memset() their buffer to zero before
use. But that seems likely to be forgotten and lead to bugs.

Instead we can change seq_buf_puts() to always leave the buffer in a
null-terminated state.

The only downside is that this makes the buffer 1 character smaller
for seq_buf_puts(), but that seems like a good trade off.

Link: http://lkml.kernel.org/r/20181019042109.8064-1-mpe@ellerman.id.auAcked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9aa3aa15 ]

In lm80_probe(), if lm80_read_value() fails, it returns a negative
error number which is stored to data->fan[f_min] and will be further
used. We should avoid using the data if the read fails.

The fix checks if lm80_read_value() fails, and if so, returns with the
error number.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c9c63915 ]

If lm80_read_value() fails, it returns a negative number instead of the
correct read data. Therefore, we should avoid using the data if it
fails.

The fix checks if lm80_read_value() fails, and if so, returns with the
error number.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
[groeck: One variable for return values is enough]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 594d1644 ]

This patch removes the check from nfs_compare_mount_options to see if a
`sec' option was passed for the current mount before comparing auth
flavors and instead just always compares auth flavors.

Consider the following scenario:

You have a server with the address 192.168.1.1 and two exports /export/a
and /export/b.  The first export supports `sys' and `krb5' security, the
second just `sys'.

Assume you start with no mounts from the server.

The following results in EIOs being returned as the kernel nfs client
incorrectly thinks it can share the underlying `struct nfs_server's:

$ mkdir /tmp/{a,b}
$ sudo mount -t nfs -o vers=3,sec=krb5 192.168.1.1:/export/a /tmp/a
$ sudo mount -t nfs -o vers=3          192.168.1.1:/export/b /tmp/b
$ df >/dev/null
df: ‘/tmp/b’: Input/output error
Signed-off-by: Chris Perl <cperl@janestreet.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7a86dab8 ]

Since the offset is added directly to the hva from the
gfn_to_hva_cache, a negative offset could result in an out of bounds
write. The existing BUG_ON only checks for addresses beyond the end of
the gfn_to_hva_cache, not for addresses before the start of the
gfn_to_hva_cache.

Note that all current call sites have non-negative offsets.

Fixes: 4ec6e863 ("kvm: Introduce kvm_write_guest_offset_cached()")
Reported-by: Cfir Cohen <cfir@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Cfir Cohen <cfir@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0db6896f ]

For fadump to work successfully there should not be any holes in reserved
memory ranges where kernel has asked firmware to move the content of old
kernel memory in event of crash. Now that fadump uses CMA for reserved
area, this memory area is now not protected from hot-remove operations
unless it is cma allocated. Hence, fadump service can fail to re-register
after the hot-remove operation, if hot-removed memory belongs to fadump
reserved region. To avoid this make sure that memory from fadump reserved
area is not hot-removable if fadump is registered.

However, if user still wants to remove that memory, he can do so by
manually stopping fadump service before hot-remove operation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e87555e5 ]

AMD doesn't seem to implement MSR_IA32_MCG_EXT_CTL and svm code in kvm
knows nothing about it, however, this MSR is among emulated_msrs and
thus returned with KVM_GET_MSR_INDEX_LIST. The consequent KVM_GET_MSRS,
of course, fails.

Report the MSR as unsupported to not confuse userspace.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2b745ac3 ]

The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).

Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.

Fixes: 9dab1868 ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 42f9b48c ]

The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).

Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.

Fixes: 9dab1868 ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ffca395b ]

On the 8xx, no-execute is set via PPP bits in the PTE. Therefore
a no-exec fault generates DSISR_PROTFAULT error bits,
not DSISR_NOEXEC_OR_G.

This patch adds DSISR_PROTFAULT in the test mask.

Fixes: d3ca5874 ("powerpc/mm: Fix reporting of kernel execute faults")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2122b405 ]

When unregistering fbdev using unregister_framebuffer(), any bound
console will unbind automatically. This is working fine if this is the
only framebuffer, resulting in a switch to the dummy console. However if
there is a fb0 and I unregister fb1 having a bound console, I eventually
get a crash. The fastest way for me to trigger the crash is to do a
reboot, resulting in this splat:

[   76.478825] WARNING: CPU: 0 PID: 527 at linux/kernel/workqueue.c:1442 __queue_work+0x2d4/0x41c
[   76.478849] Modules linked in: raspberrypi_hwmon gpio_backlight backlight bcm2835_rng rng_core [last unloaded: tinydrm]
[   76.478916] CPU: 0 PID: 527 Comm: systemd-udevd Not tainted 4.20.0-rc4+ #4
[   76.478933] Hardware name: BCM2835
[   76.478949] Backtrace:
[   76.478995] [<c010d388>] (dump_backtrace) from [<c010d670>] (show_stack+0x20/0x24)
[   76.479022]  r6:00000000 r5:c0bc73be r4:00000000 r3:6fb5bf81
[   76.479060] [<c010d650>] (show_stack) from [<c08e82f4>] (dump_stack+0x20/0x28)
[   76.479102] [<c08e82d4>] (dump_stack) from [<c0120070>] (__warn+0xec/0x12c)
[   76.479134] [<c011ff84>] (__warn) from [<c01201e4>] (warn_slowpath_null+0x4c/0x58)
[   76.479165]  r9:c0eb6944 r8:00000001 r7:c0e927f8 r6:c0bc73be r5:000005a2 r4:c0139e84
[   76.479197] [<c0120198>] (warn_slowpath_null) from [<c0139e84>] (__queue_work+0x2d4/0x41c)
[   76.479222]  r6:d7666a00 r5:c0e918ee r4:dbc4e700
[   76.479251] [<c0139bb0>] (__queue_work) from [<c013a02c>] (queue_work_on+0x60/0x88)
[   76.479281]  r10:c0496bf8 r9:00000100 r8:c0e92ae0 r7:00000001 r6:d9403700 r5:d7666a00
[   76.479298]  r4:20000113
[   76.479348] [<c0139fcc>] (queue_work_on) from [<c0496c28>] (cursor_timer_handler+0x30/0x54)
[   76.479374]  r7:d8a8fabc r6:c0e08088 r5:d8afdc5c r4:d8a8fabc
[   76.479413] [<c0496bf8>] (cursor_timer_handler) from [<c0178744>] (call_timer_fn+0x100/0x230)
[   76.479435]  r4:c0e9192f r3:d758a340
[   76.479465] [<c0178644>] (call_timer_fn) from [<c0178980>] (expire_timers+0x10c/0x12c)
[   76.479495]  r10:40000000 r9:c0e9192f r8:c0e92ae0 r7:d8afdccc r6:c0e19280 r5:c0496bf8
[   76.479513]  r4:d8a8fabc
[   76.479541] [<c0178874>] (expire_timers) from [<c0179630>] (run_timer_softirq+0xa8/0x184)
[   76.479570]  r9:00000001 r8:c0e19280 r7:00000000 r6:c0e08088 r5:c0e1a3e0 r4:c0e19280
[   76.479603] [<c0179588>] (run_timer_softirq) from [<c0102404>] (__do_softirq+0x1ac/0x3fc)
[   76.479632]  r10:c0e91680 r9:d8afc020 r8:0000000a r7:00000100 r6:00000001 r5:00000002
[   76.479650]  r4:c0eb65ec
[   76.479686] [<c0102258>] (__do_softirq) from [<c0124d10>] (irq_exit+0xe8/0x168)
[   76.479716]  r10:d8d1a9b0 r9:d8afc000 r8:00000001 r7:d949c000 r6:00000000 r5:c0e8b3f0
[   76.479734]  r4:00000000
[   76.479764] [<c0124c28>] (irq_exit) from [<c016b72c>] (__handle_domain_irq+0x94/0xb0)
[   76.479793] [<c016b698>] (__handle_domain_irq) from [<c01021dc>] (bcm2835_handle_irq+0x3c/0x48)
[   76.479823]  r8:d8afdebc r7:d8afddfc r6:ffffffff r5:c0e089f8 r4:d8afddc8 r3:d8afddc8
[   76.479851] [<c01021a0>] (bcm2835_handle_irq) from [<c01019f0>] (__irq_svc+0x70/0x98)

The problem is in the console rebinding in fbcon_fb_unbind(). It uses the
virtual console index as the new framebuffer index to bind the console(s)
to. The correct way is to use the con2fb_map lookup table to find the
framebuffer index.

Fixes: cfafca80 ("fbdev: fbcon: console unregistration from unregister_framebuffer")
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 98cff8b2 ]

In __ghes_panic() clear the block status in the APEI generic
error status block for that generic hardware error source before
calling panic() to prevent a second panic() in the crash kernel
for exactly the same fatal error.

Otherwise ghes_probe(), running in the crash kernel, would see
an unhandled error in the APEI generic error status block and
panic again, thereby precluding any crash dump.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Tyler Baicar <baicar.tyler@gmail.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>