Use the DT helpers in the ASoC core to parse the "pin-switches" and
"widgets" properties from the device tree. This allows adding extra
mixers to disable e.g. an extra speaker amplifier that would be
normally powered on automatically because it is connected to a shared
output pin.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211214142049.20422-4-stephan@gerhold.netSigned-off-by: Mark Brown <broonie@kernel.org>

Some sound card setups might require extra pin switches to allow
turning off certain audio components. There are two real examples for
this in smartphones/tablets based on MSM8916:

  1. Analog speaker amplifiers connected to headphone outputs.

     The MSM8916 analog codec does not have a separate "Line Out" port
     so some devices have an analog speaker amplifier connected to one
     of the headphone outputs. A pin switch is necessary to allow
     playback on headphones without also activating the speaker.

  2. External speaker codec also used as earpiece.

     Some smartphones have two front-facing (stereo) speakers that can
     be also configured to act as an earpiece during voice calls. A pin
     switch is needed to allow disabling the second speaker during
     voice calls.

There are existing bindings that allow setting up such pin switches in
simple-card.yaml. Document the same for Qcom sound cards.

One variant of example 1 above is added to the examples in the DT
schema: There is an analog speaker amplifier connected to the HPH_R
(right headphone channel) output. Adding a "Speaker" pin switch and
widget allows turning off the speaker when audio should be only played
via the connected headphones.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211214142049.20422-3-stephan@gerhold.netSigned-off-by: Mark Brown <broonie@kernel.org>

The ASoC core already has several helpers to parse card properties
from the device tree. Move the parsing code for "pin-switches" from
simple-card-utils to a shared snd_soc_of_parse_pin_switches() function
so other drivers can also use it to set up pin switches configured in
the device tree.

Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211214142049.20422-2-stephan@gerhold.netSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Alexander Stein <alexander.stein@mailbox.org>:

Following up [1] here are more fix for missing sound-name-prefix
properties in the arch/arm64/boot/dts/amlogic/ subtree.

[1] https://www.spinics.net/lists/devicetree/msg466125.html

Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:

this series will improve how we are tracking the firmware's state to be able to
avoid communication with it when it is not going to answer due to a panic and
we will attempt to force power cycle the DSP to recover at the next runtime
suspend time.

The state handling brings in other improvements on the way the kernel reports
errors and DSP panics to reduce the printed lines for normal users, but at the
same time allowing developers (or for bug reports) to have more precise
information available to track down the issue.

We can now place messages easily in the correct debug level and not bound to the
static ERROR for some of the print chains, causing excess amount or partial
information to be printed, confusing users and machines (CI).

I would have prefered to split this series up, but it was developed together to
achieve a single goal to reduce the noise, but also provide the details we need
to be able to rootcause issues.

Fix the missing clk_disable_unprepare() before return
from adc3xxx_i2c_probe() in the error handling case.

Fixes: e9a3b57e ("ASoC: codec: tlv320adc3xxx: New codec driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211223082212.3342184-1-yangyingliang@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

This is used in meson-gx. Add the property to the binding.
This fixes the dtschema warning:
audio-controller@5400: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Link: https://lore.kernel.org/r/20211223122434.39378-4-alexander.stein@mailbox.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This is used in meson-axg, meson-g12 and meson-gx. Add the property to
the binding.
This fixes the dtschema warning:
audio-codec-0: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Link: https://lore.kernel.org/r/20211223122434.39378-3-alexander.stein@mailbox.orgSigned-off-by: Mark Brown <broonie@kernel.org>

If the user requested to see all dumps (even the optional ones) then use
KERN_DEBUG level for the optional dumps as they are only for debugging
purposes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-21-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

If the user requested to see all dumps (even the optional ones) then use
KERN_DEBUG level for the optional dumps as they are only for debugging
purposes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-20-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Update the comment for the global SOF level debug flags and add one for
the flags used to control the DSP dump functionality.

Document the expected behavior when the SOF_DBG_DUMP_OPTIONAL is passed
for the DSP dump:
Only print the dump if SOF_DBG_PRINT_ALL_DUMPS is set
Print must use KERN_DEBUG log level
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-19-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The snd_sof_get_status() is not the best name for a function which in fact
is tasked to print out DSP oops and stack. Rename it to
sof_print_oops_and_stack().

At the same time add a new parameter to specify the desired kernel log
level to be used for the prints.

When updating the users of the function, pass KERN_ERR for now to make sure
that there is no functional change happens.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-18-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

To allow custom log level to be used for the DSP oops and stack print, add
a kernel log level parameter to the two ops.

Modify the xtensa oops and stack functions tom use this new log level
parameter.

Pass KER_ERR from snd_sof_get_status() to make sure that there is no
functional change with this new parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-17-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Never suppress the DSP panic dump as it is always originates from an
assert() or panic() call within the firmware.

Use different message for DSP panics when there will be recovery attempt
going to be done compared to a definitive DSP panic.
Suggested-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-16-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Update the state flow diagram to reflect the current implementation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-15-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Try to force the DSP to be turned off next time if the fw_state is either
CRASHED or BOOT_FAILED when a suspend happens in order to attempt a clean
boot to recover.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-14-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Change the fw_state to SOF_FW_BOOT_FAILED if we encountered an error during
booting the firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-13-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

If the state of the firmware is not BOOT_COMPLETE, it means that the
firmware is not functioning, thus it is not capable of handling IPC
messages.
Do not try to send IPC if the state is not BOOT_COMPLETE
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-12-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since there is nothing SND about the firmware state, rename the enum
from `snd_sof_fw_state` to simply `sof_fw_state`
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Link: https://lore.kernel.org/r/20211223113628.18582-11-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Move the enum snd_sof_fw_state to include/sound/sof.h to be accessible
outside of the core SOF stack.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Link: https://lore.kernel.org/r/20211223113628.18582-10-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The SOF_FW_BOOT_READY_OK fw_state indicates that the boot ready message has
been received and there were no errors found.

The SOF_FW_BOOT_COMPLETE state will be reached after the
snd_sof_dsp_post_fw_run() completes without error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Link: https://lore.kernel.org/r/20211223113628.18582-9-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The SOF_FW_CRASHED state is meant to indicate the unfortunate case when the
firmware has crashed after a successful boot.

IPC tx timeout is not treated as indication of a firmware crash as it tends
to happen regularly while the firmware is operational.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Link: https://lore.kernel.org/r/20211223113628.18582-8-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When snd_sof_dsp_dbg_dump() is called we have an explanatory message to
give some hint on the reason why we have the dump on the caller level.

Pass this message to snd_sof_dsp_dbg_dump() and handle the print according
to the dump rules.

This way we can finally print information on the HDA boot iteration if all
dumps are enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-7-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Some platforms use retries during firmware boot to overcome DSP startup
issues.
In these cases we might receive a DSP panic message which should not be
treated as fatal if it happens during boot.

Pass this information to snd_sof_dsp_panic() and omit the panic print if
it is not fatal or the user does not want to see all dumps.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-6-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The sof_debug_check_flag() is available for checking flags set in
sof_core_debug.

sof_core_debug can be marked static in core.c
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-5-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The sof_debug_check_flag() can be used to check a flag or a combination of
them in sof_core_debug.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-4-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

HDA_FW_BOOT_ATTEMPTS is defined in hda.h, do not define it again locally
in hda-loader.c

At the same time correct the indentation for the define in hda.h
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-3-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Catch the cases when the stored sdev->dsp_oops_offset and the offset
received via the panic message differs and print a warning, but keep using
the dsp_oops_offset for the oops query.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-2-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Don't use enums for DACL/DACR Signal Invert controls,
and change them into a stereo "DAC Signal Invert Switch" control.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Link: https://lore.kernel.org/r/20211222135403.2991657-1-vincent.knecht@mailoo.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This is used in meson-sm1 and meson-g12 .dtsi. Add the property to
the binding.
This fixes the dtschema warning:
audio-controller@740: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211218143423.18768-3-alexander.stein@mailbox.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This is used in meson-gxl and meson-g12-common .dtsi. Add the property to
the binding.
This fixes the dtschema warning:
audio-controller@32000: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211218143423.18768-2-alexander.stein@mailbox.orgSigned-off-by: Mark Brown <broonie@kernel.org>

name-prefix.txt does not exist anymore, just reference the schema instead.
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211218143423.18768-1-alexander.stein@mailbox.orgSigned-off-by: Mark Brown <broonie@kernel.org>

AK4375 is a 32-bit stereo DAC with headphones amplifier.
There's no documentation for it on akm.com, and only a brief
datasheet can be found floating on the internets [1].

Thanks to Oriane BAYERD <obayerd@eurocomposant.fr>
for finally answering my inquiries through akm.com, if only to tell
me that this chip is EOL following AKM factory burning in october 2020
and thus no detailed documentation is available anymore...

AK4331 is advertised [2] as pin and register compatible with AK4375
so some scraps of its datasheet were used and this driver might be
used as a base for it, but this is totally untested.

So this driver is mainly based on downstream code [3] and [4]
by Hu Jin from AKM (no known email).

Tested on msm8916-alcatel-idol347 and msm8939-alcatel-idol3,
which both use PLL driven clock with bypass of SRC (sample rate
converter), so only this setup is supported for now.

[1] https://datasheetspdf.com/pdf-file/1400317/AKM/AK4375A/1
[2] https://www.akm.com/content/dam/documents/products/audio/audio-dac/ak4331ecb/ak4331ecb-en-datasheet.pdf
[3] https://github.com/msm8916-mainline/android_kernel_qcom_msm8916/blob/alcatel-idol347/sound/soc/codecs/idol347/ak4375.c
[4] https://github.com/msm8916-mainline/android_kernel_qcom_msm8916/blob/alcatel-idol347/sound/soc/codecs/ak4375.cSigned-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Link: https://lore.kernel.org/r/20211220193725.2650356-2-vincent.knecht@mailoo.orgSigned-off-by: Mark Brown <broonie@kernel.org>

AK4375 is an audio DAC with headphones amplifier controlled via I2C.
Add simple device tree bindings that describe how to set it up.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Link: https://lore.kernel.org/r/20211220193725.2650356-1-vincent.knecht@mailoo.orgSigned-off-by: Mark Brown <broonie@kernel.org>

platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.

In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().

While at it also drop "r_irq" member from struct bcm_i2s_priv as there
are no users of it.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211221170100.27423-3-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.

In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211221170100.27423-2-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove duplicate depends on statement in Kconfig file.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20211221171912.237792-1-AjitKumar.Pandey@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

This code frees "graph" and then dereferences to save the error code.
Save the error code first and then use gotos to unwind the allocation.

Fixes: 59716aa3 ("ASoC: qdsp6: Fix an IS_ERR() vs NULL bug")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211217150007.GB16611@kiliSigned-off-by: Mark Brown <broonie@kernel.org>

cppcheck warning:

sound/soc/sof/amd/acp.c:222:9: warning: Identical condition and return
expression 'ret', return value is always 0
[identicalConditionAfterEarlyExit]
 return ret;
        ^
sound/soc/sof/amd/acp.c:213:6: note: If condition 'ret' is true, the
function will return/exit
 if (ret)
     ^
sound/soc/sof/amd/acp.c:222:9: note: Returning identical expression 'ret'
 return ret;
        ^

Just return 0; on success.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20211221165802.236843-1-AjitKumar.Pandey@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove non-existent properties from the example of the binding. These
properties were borrower from the old txt binding, but they were never
used in practice and aren't documented in the new binding. They aren't
reported by the binding checker because dtschema needs extra patch that
hasn't been upstreamed yet to make unevaluatedProperties work properly.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211216160229.17049-1-digetx@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>