There was a change in the mxs-dma engine that uses a new custom flag.
The change was not applied to the mxs spi driver.
This results in chipselect being deasserted too early.
This fixes the chipselect problem by using the new flag in the mxs-spi
driver.

Fixes: ceeeb99c ("dmaengine: mxs: rename custom flag")
Signed-off-by: Ralf Schlatterbeck <rsc@runtux.com>
Link: https://msgid.link/r/20240202115330.wxkbfmvd76sy3a6a@runtux.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add Intel Lunar Lake-M PCI ID to the driver list of supported devices.
This is the same controller found in previous generations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://msgid.link/r/20240212082027.2462849-1-mika.westerberg@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

MCSPI controller have few limitations regarding the transaction
size when the FIFO buffer is enabled and the WCNT feature is used
to find the end of word, in this case if WCNT is not a multiple of
the FIFO Almost Empty Level (AEL), then the FIFO empty event is not
generated correctly. In addition to this limitation, few other unknown
sequence of events that causes the FIFO empty status to not reflect the
exact status were found when FIFO is being used without DMA enabled
during extended testing in AM65x platform. Till the exact root cause
is found and fixed, revert the FIFO support without DMA.

See J721E Technical Reference Manual (SPRUI1C), section 12.1.5
for further details: http://www.ti.com/lit/pdf/spruil1

This reverts commit 75223bbe ("spi: omap2-mcspi: Add FIFO support
without DMA")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://msgid.link/r/20240212120049.438495-1-vaishnav.a@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

Since commit 24778be2 ("spi: convert drivers to use
bits_per_word_mask") the bits_per_word variable is only written to. The
check that was there before isn't needed any more as the spi core
ensures that only 8 bit transfers are used, so the variable can go away
together with all assignments to it.

Fixes: 24778be2 ("spi: convert drivers to use bits_per_word_mask")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240210164006.208149-8-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

I failed to adapt this driver because it's not enabled in a powerpc
allmodconfig build and also wasn't hit by my grep expertise. Fix
accordingly.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402100815.XQXw9XCF-lkp@intel.com/
Fixes: 22592331 ("spi: bitbang: Follow renaming of SPI "master" to "controller"")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240210164006.208149-7-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

The driver uses several symbols declared in <linux/platform_device.h>,
e.g module_platform_driver(). Include this header explicitly now that
<linux/of_platform.h> doesn't include <linux/platform_device.h> any
more.

Fixes: ef175b29 ("of: Stop circularly including of_device.h and of_platform.h")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240210164006.208149-6-u.kleine-koenig@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

the driver currently fails to compile on 6.8-rc3 due to:
| spi-ppc4xx.c: In function ‘spi_ppc4xx_of_probe’:
| @346:36: error: invalid use of undefined type ‘struct platform_device’
| 346 |         struct device_node *np = op->dev.of_node;
|     |                                    ^~
| ... (more similar errors)

it was working with 6.7. Looks like it only needed the include
and its compiling fine!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://lore.kernel.org/r/3eb3f9c4407ba99d1cd275662081e46b9e839173.1707490664.git.chunkeey@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

For DMA mode, the bus width of the DMA is equal to the size of data
word, so burst length should be configured as bits per word.

For CPU mode, because of the spi transfer len is in byte, so calculate
the total number of words according to spi transfer len and bits per
word, burst length should be configured as total data bits.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Fixes: e9b220ae ("spi: spi-imx: correctly configure burst length when using dma")
Fixes: 5f66db08 ("spi: imx: Take in account bits per word instead of assuming 8-bits")
Link: https://lore.kernel.org/r/20240204091912.36488-1-carlos.song@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

cppcheck rightfully warned:

 drivers/spi/spi-sh-msiof.c:792:28: warning: Signed integer overflow for expression '7<<29'. [integerOverflow]
 sh_msiof_write(p, SIFCTR, SIFCTR_TFWM_1 | SIFCTR_RFWM_1);
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://msgid.link/r/20240130094053.10672-1-wsa+renesas@sang-engineering.comSigned-off-by: Mark Brown <broonie@kernel.org>

In __spi_pump_transfer_message(), the message was not finalized in the
first error return as it is in the other error return paths. Not
finalizing the message could cause anything waiting on the message to
complete to hang forever.

This adds the missing call to spi_finalize_current_message().

Fixes: ae7d2346 ("spi: Don't use the message queue if possible in spi_sync")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240125205312.3458541-2-dlechner@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

As it devm_pm_runtime_enable can fail due to memory allocations, it is
best to handle the error.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://msgid.link/r/20240124174101.2270249-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

As reported by Guenter the limit we've got on the number of chip selects is
set too low for some systems, raise the limit. We should really remove the
hard coded limit but this is needed as a fix so let's do the simple thing
and raise the limit for now.

Fixes: 4d8ff6b0 ("spi: Add multi-cs memories support in SPI core")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://msgid.link/r/20240124-spi-multi-cs-max-v2-1-df6fc5ab1abc@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Return IRQ_NONE from the interrupt handler when no interrupt was
detected. Because an empty interrupt will cause a null pointer error:

    Unable to handle kernel NULL pointer dereference at virtual
  address 0000000000000008
    Call trace:
        complete+0x54/0x100
        hisi_sfc_v3xx_isr+0x2c/0x40 [spi_hisi_sfc_v3xx]
        __handle_irq_event_percpu+0x64/0x1e0
        handle_irq_event+0x7c/0x1cc
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Link: https://msgid.link/r/20240123071149.917678-1-liudingyuan@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

In the existing implementation, when executing interleaved write and read
operations in the ISR for a transfer length greater than the FIFO size,
the TXFIFO write precedes the RXFIFO read. Consequently, the initially
received data in the RXFIFO is pushed out and lost, leading to a failure
in data integrity. To address this issue, reverse the order of interleaved
operations and conduct the RXFIFO read followed by the TXFIFO write.

Fixes: 6afe2ae8 ("spi: spi-cadence: Interleave write of TX and read of RX FIFO")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://msgid.link/r/20231218090652.18403-1-amit.kumar-mahapatra@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

If dma_request_chan() fails, no error is shown nor any information is
shown in /sys/kernel/debug/devices_deferred if -EPROBE_DEFER is returned.
Use dev_err_probe to fix both problems.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://msgid.link/r/20240110085403.457089-1-alexander.stein@ew.tq-group.comSigned-off-by: Mark Brown <broonie@kernel.org>

SFDP read shall use the mspi reads when using the bcm_qspi_exec_mem_op()
call. This fixes SFDP parameter page read failures seen with parts that
now use SFDP protocol to read the basic flash parameter table.

Fixes: 5f195ee7 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://msgid.link/r/20240109210033.43249-1-kamal.dasu@broadcom.comSigned-off-by: Mark Brown <broonie@kernel.org>

This adds the PCI ID of the Arrow Lake and Meteor Lake-S PCH SPI serial
flash controller. This one supports all the necessary commands Linux
SPI-NOR stack requires.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://msgid.link/r/20240122120034.2664812-3-mika.westerberg@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Turns out this "SoC" side controller does not support certain commands,
such as reading chip JEDEC ID, so the controller is pretty much unusable
in Linux. We should be using the "PCH" side controller instead. For this
reason remove this PCI ID from the list.

Fixes: c2912d42 ("spi: intel-pci: Add support for Meteor Lake-S SPI serial flash")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://msgid.link/r/20240122120034.2664812-2-mika.westerberg@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB

Add line breaks - inode_to_text() is now much easier to read.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs_format.h has gotten too big; let's do some organizing.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Add a field to bch_snapshot for creation time; this will be important
when we start exposing the snapshot tree to userspace.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

The "apply this compression method in the background" paths now use the
compression option if background_compression is not set; this means that
setting or changing the compression option will cause existing data to
be compressed accordingly in the background.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>