- 25 Apr, 2014 2 commits
-
-
Sergei Shtylyov authored
Define the Henninger board dependent part of the Ether device node. Enable DHCP and NFS root for the kernel booting. Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au>
-
Sergei Shtylyov authored
Add the initial device tree for the R8A7791 SoC based Henninger board. SCIF0 serial port support is included, so that the serial console can work. Signed-off-by:
-
- 16 Apr, 2014 1 commit
-
-
Geert Uytterhoeven authored
Use "sii,s35390a" instead of "seiko,s35390a", cfr. Documentation/devicetree/bindings/i2c/trivial-devices.txt and Documentation/devicetree/bindings/vendor-prefixes.txt. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by:
-
- 14 Apr, 2014 32 commits
-
-
Geert Uytterhoeven authored
Signed-off-by:
Magnus Damm <damm@opensource.se> Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
Wolfram Sang <wsa@sang-engineering.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Laurent Pinchart authored
All I2C clocks derive from the HP clock, not from the P clock. Fix them. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by:
Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by:
-
Laurent Pinchart authored
All I2C clocks derive from the HP clock, not from the P clock. Fix them. Signed-off-by:
-
Simon Horman authored
The correct binding is "micrel,led-mode", not "led-mode". This corrects an error which was introduced when setting of ethernet PHY LED mode was added by 82e62182d59bd1d0 ("ARM: shmobile: lager: Set ethernet PHY LED mode"). This makes the lager code consistent with the koelsch code which was added by ae00d12a032490b3 ("ARM: shmobile: koelsch: Set ethernet PHY LED mode"). Acked-by: -
Ulrich Hecht authored
This enables the Seiko real-time clock that is attached to a couple of GPIO pins. Signed-off-by:
Ulrich Hecht <ulrich.hecht@gmail.com> Signed-off-by:
-
Magnus Damm authored
Add support for EHCI clock gating via the MSTP703 bit on r8a7791. Signed-off-by:
-
Ulrich Hecht authored
Add "renesas,*-r8a7740" to the compatible strings for consistency with other devices. Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Wolfram Sang authored
This node should have a unique name so it can be distinguished when other i2c busses are added later. Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Laurent Pinchart authored
The Koelsch board uses the ethernet PHY LED0 as a link signal connected to the ethernet controller. Specify the corresponding LED mode for the PHY. Signed-off-by:
-
Laurent Pinchart authored
The Lager board uses the ethernet PHY LED0 as a link signal connected to the ethernet controller. Specify the corresponding LED mode for the PHY. Signed-off-by:
-
Magnus Damm authored
Add DTS gpio-keys support for SW2 on the Koelsch board. This makes the DT code match the legacy board code. Also update the existing gpio-keys nodes to make use of KEY_n. Signed-off-by:
-
Magnus Damm authored
Add DTS gpio-keys support for SW2 on the Lager board. This makes the DT code match the legacy board code. Signed-off-by:
-
Geert Uytterhoeven authored
Add Spansion s25fl008k SPI FLASH and MTD partition, based on bockw legacy board code. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
Geert Uytterhoeven authored
- Add "renesas,hspi-r8a7779" compatible value, - Correct reference to parent interrupt controller (use "interrupt-parent" instead of "interrupt-controller"), - Add missing "#address-cells" and "#size-cells" properties, which are needed when populating the SPI buses. Signed-off-by: -
Geert Uytterhoeven authored
- Add "renesas,hspi-r8a7778" compatible value, - Correct reference to parent interrupt controller (use "interrupt-parent" instead of "interrupt-controller"), - Add missing "#address-cells" and "#size-cells" properties, which are needed when populating the SPI buses. Signed-off-by: -
Geert Uytterhoeven authored
Add pinctrl and SPI device for MSIOF on Koelsch. On this board, only MSIOF0 is in use. Its bus contains a single device (a Renesas R2A11302FT PMIC), for which no bindings are defined yet. Signed-off-by:
-
Geert Uytterhoeven authored
Add pinctrl and SPI device for MSIOF on Lager. On this board, only MSIOF1 is in use. Its bus contains a single device (a Renesas R2A11302FT PMIC), for which no bindings are defined yet. Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Prepare for the advent of MSIOF SPI, which will be spi1 to spi3. Signed-off-by:
-
Geert Uytterhoeven authored
Prepare for the advent of MSIOF SPI, which will be spi1 to spi4. Signed-off-by:
-
Magnus Damm authored
The correct maximum CPU frequency for r8a7791 is 1500 MHz so update the r8a7791 SoC DTS to reflect this. Signed-off-by:
-
- 13 Apr, 2014 5 commits
-
-
Linus Torvalds authored
-
Geert Uytterhoeven authored
Some versions of gcc even warn about it: mm/shmem.c: In function ‘shmem_file_aio_read’: mm/shmem.c:1414: warning: ‘error’ may be used uninitialized in this function If the loop is aborted during the first iteration by one of the two first break statements, error will be uninitialized. Introduced by commit 6e58e79d ("introduce copy_page_to_iter, kill loop over iovec in generic_file_aio_read()"). Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Geert Uytterhoeven authored
On 32 bit, size_t is "unsigned int", not "unsigned long", causing the following warning when comparing with PAGE_SIZE, which is always "unsigned long": fs/cifs/file.c: In function ‘cifs_readdata_to_iov’: fs/cifs/file.c:2757: warning: comparison of distinct pointer types lacks a cast Introduced by commit 7f25bba8 ("cifs_iovec_read: keep iov_iter between the calls of cifs_readdata_to_iov()"), which changed the signedness of "remaining" and the code from min_t() to min(). Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linuxLinus Torvalds authored
Pull slab changes from Pekka Enberg: "The biggest change is byte-sized freelist indices which reduces slab freelist memory usage: https://lkml.org/lkml/2013/12/2/64" * 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux: mm: slab/slub: use page->list consistently instead of page->lru mm/slab.c: cleanup outdated comments and unify variables naming slab: fix wrongly used macro slub: fix high order page allocation problem with __GFP_NOFAIL slab: Make allocations with GFP_ZERO slightly more efficient slab: make more slab management structure off the slab slab: introduce byte sized index for the freelist of a slab slab: restrict the number of objects in a slab slab: introduce helper functions to get/set free object slab: factor out calculate nr objects in cache_estimate -
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuildLinus Torvalds authored
Pull misc kbuild changes from Michal Marek: "Here is the non-critical part of kbuild: - One bogus coccinelle check removed, one check fixed not to suggest the obsolete PTR_RET macro - scripts/tags.sh does not index the generated *.mod.c files - new objdiff tool to list differences between two versions of an object file - A fix for scripts/bootgraph.pl" * 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: scripts/coccinelle: Use PTR_ERR_OR_ZERO scripts/bootgraph.pl: Add graphic header scripts: objdiff: detect object code changes between two commits Coccicheck: Remove memcpy to struct assignment test scripts/tags.sh: Ignore *.mod.c
-
