Merge tag 'mac80211-next-for-net-next-2020-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Another set of changes, this time with:
 * lots more S1G band support
 * 6 GHz scanning, finally
 * kernel-doc fixes
 * non-split wiphy dump fixes in nl80211
 * various other small cleanups/features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use more generic eth_platform_get_mac_address() which can get a MAC
address from other than DT platform specific sources too. Check if the
obtained address is valid.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The switch has a certain MDIO address and this needs to be specified using the
reg property. Add it to the example.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: Improve dsa_untag_bridge_pvid()

This patch series is based on the recent discussions with Vladimir:

https://lore.kernel.org/netdev/20201001030623.343535-1-f.fainelli@gmail.com/

the simplest way forward was to call dsa_untag_bridge_pvid() after
eth_type_trans() has been set which guarantees that skb->protocol is set
to a correct value and this allows us to utilize
__vlan_find_dev_deep_rcu() properly without playing or using the bridge
master as a net_device reference.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we are guaranteed that dsa_untag_bridge_pvid() is called after
eth_type_trans() we can utilize __vlan_find_dev_deep_rcu() which will
take care of finding an 802.1Q upper on top of a bridge master.

A common use case, prior to 12a1526d067 ("net: dsa: untag the bridge
pvid from rx skbs") was to configure a bridge 802.1Q upper like this:

ip link add name br0 type bridge vlan_filtering 0
ip link add link br0 name br0.1 type vlan id 1

in order to pop the default_pvid VLAN tag.

With this change we restore that behavior while still allowing the DSA
receive path to automatically pop the VLAN tag.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that dsa_untag_bridge_pvid() is called after eth_type_trans() we are
guaranteed that skb->protocol will be set to a correct value, thus
allowing us to avoid calling vlan_eth_hdr().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Indicate to the DSA receive path that we need to untage the bridge PVID,
this allows us to remove the dsa_untag_bridge_pvid() calls from
net/dsa/tag_brcm.c.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a DSA switch driver needs to call dsa_untag_bridge_pvid(), it can
set dsa_switch::untag_brige_pvid to indicate this is necessary.

This is a pre-requisite to making sure that we are always calling
dsa_untag_bridge_pvid() after eth_type_trans() has been called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2020-10-02

1) Add a full xfrm compatible layer for 32-bit applications on
   64-bit kernels. From Dmitry Safonov.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

[ Upstream commit a95bc734 ]

If userspace doesn't complete the policy dump, we leak the
allocated state. Fix this.

Fixes: d07dcf9a ("netlink: add infrastructure to expose policies to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ieee80211_determine_chantype(), the sband->ht_cap was
being processed before S1G Operation element.  Since the
HT capability element should not be present on the S1G
band, avoid processing potential garbage by moving the
call to ieee80211_apply_htcap_overrides() to after the S1G
block.

Also, in case of a missing S1G Operation element, we would
continue trying to process non-S1G elements (and return
with a channel width of 20MHz). Instead, just assume
primary channel is equal to operating and infer the
operating width from the BSS channel, then return.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201001174748.24520-1-thomas@adapt-ip.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

When dumping wiphy information, we try to split the data into
many submessages, but for old userspace we still support the
old mode where this doesn't happen.

However, in this case we were not resetting our state correctly
and dumping multiple messages for each wiphy, which would have
broken such older userspace.

This was broken pretty much immediately afterwards because it
only worked in the original commit where non-split dumps didn't
have any more data than split dumps...

Fixes: fe1abafd ("nl80211: re-add channel width and extended capa advertising")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200928130717.3e6d9c6bada2.Ie0f151a8d0d00a8e1e18f6a8c9244dd02496af67@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

When wiphy dumps cannot be split, such as in events or with
older userspace that doesn't support it, the size can today
be too big.

Reduce it, by doing two things:

 1) remove data that couldn't have been present before the
    split capability was introduced since it's new, such as
    HE capabilities

 2) as suggested by Martin Willi, remove management frame
    subtypes from the split dumps, as just (1) isn't even
    enough due to other new code capabilities. This is fine
    as old consumers (really just wpa_supplicant) didn't
    check this data before they got support for split dumps.
Reported-by: Martin Willi <martin@strongswan.org>
Suggested-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Martin Willi <martin@strongswan.org>
Link: https://lore.kernel.org/r/20200928130655.53bce7873164.I71f06c9a221cd0630429a1a56eeae68a13beca61@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Use netif_msg_init() to process param settings
and use only the proper initialized value of
ei_local->msg_level for later processing;
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Realtek single-chip Ethernet PHY solutions can be separated as below:
10M/100Mbps: RTL8201X
1Gbps: RTL8211X
2.5Gbps: RTL8226/RTL8221X
RTL8226 is the first version for realtek that compatible 2.5Gbps single PHY.
Since RTL8226 is single port only, realtek changes its name to RTL8221B from
the second version.
PHY ID for RTL8226 is 0x001cc800 and RTL8226B/RTL8221B is 0x001cc840.

RTL8125 is not a single PHY solution, it integrates PHY/MAC/PCIE bus
controller and embedded memory.
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit a8c7687b ("caif_virtio: Check that vringh_config is not
null"), the variable err is being initialized with '-EINVAL' that is
meaningless. So remove it.
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix follow warnings:
[net/core/net-sysfs.c:1161]: (warning) %u in format string (no. 1)
	requires 'unsigned int' but the argument type is 'int'.
[net/core/net-sysfs.c:1162]: (warning) %u in format string (no. 1)
	requires 'unsigned int' but the argument type is 'int'.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix follow warnings:
[net/core/pktgen.c:925]: (warning) %u in format string (no. 1)
	requires 'unsigned int' but the argument type is 'signed int'.
[net/core/pktgen.c:942]: (warning) %u in format string (no. 1)
	requires 'unsigned int' but the argument type is 'signed int'.
[net/core/pktgen.c:962]: (warning) %u in format string (no. 1)
	requires 'unsigned int' but the argument type is 'signed int'.
[net/core/pktgen.c:984]: (warning) %u in format string (no. 1)
	requires 'unsigned int' but the argument type is 'signed int'.
[net/core/pktgen.c:1149]: (warning) %d in format string (no. 1)
	requires 'int' but the argument type is 'unsigned int'.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fr_hard_header function is used to prepend the header to skbs before
transmission. It is used in 3 situations:
1) When a control packet is generated internally in this driver;
2) When a user sends an skb on an Ethernet-emulating PVC device;
3) When a user sends an skb on a normal PVC device.

These 3 situations need to be handled differently by fr_hard_header.
Different headers should be prepended to the skb in different situations.

Currently fr_hard_header distinguishes these 3 situations using
skb->protocol. For situation 1 and 2, a special skb->protocol value
will be assigned before calling fr_hard_header, so that it can recognize
these 2 situations. All skb->protocol values other than these special ones
are treated by fr_hard_header as situation 3.

However, it is possible that in situation 3, the user sends an skb with
one of the special skb->protocol values. In this case, fr_hard_header
would incorrectly treat it as situation 1 or 2.

This patch tries to solve this issue by using skb->dev instead of
skb->protocol to distinguish between these 3 situations. For situation
1, skb->dev would be NULL; for situation 2, skb->dev->type would be
ARPHRD_ETHER; and for situation 3, skb->dev->type would be ARPHRD_DLCI.

This way fr_hard_header would be able to distinguish these 3 situations
correctly regardless what skb->protocol value the user tries to use in
situation 3.

Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2020-10-01

The following pull-request contains BPF updates for your *net-next* tree.

We've added 90 non-merge commits during the last 8 day(s) which contain
a total of 103 files changed, 7662 insertions(+), 1894 deletions(-).

Note that once bpf(/net) tree gets merged into net-next, there will be a small
merge conflict in tools/lib/bpf/btf.c between commit 12450081 ("libbpf: Fix
native endian assumption when parsing BTF") from the bpf tree and the commit
3289959b ("libbpf: Support BTF loading and raw data output in both endianness")
from the bpf-next tree. Correct resolution would be to stick with bpf-next, it
should look like:

  [...]
        /* check BTF magic */
        if (fread(&magic, 1, sizeof(magic), f) < sizeof(magic)) {
                err = -EIO;
                goto err_out;
        }
        if (magic != BTF_MAGIC && magic != bswap_16(BTF_MAGIC)) {
                /* definitely not a raw BTF */
                err = -EPROTO;
                goto err_out;
        }

        /* get file size */
  [...]

The main changes are:

1) Add bpf_snprintf_btf() and bpf_seq_printf_btf() helpers to support displaying
   BTF-based kernel data structures out of BPF programs, from Alan Maguire.

2) Speed up RCU tasks trace grace periods by a factor of 50 & fix a few race
   conditions exposed by it. It was discussed to take these via BPF and
   networking tree to get better testing exposure, from Paul E. McKenney.

3) Support multi-attach for freplace programs, needed for incremental attachment
   of multiple XDP progs using libxdp dispatcher model, from Toke Høiland-Jørgensen.

4) libbpf support for appending new BTF types at the end of BTF object, allowing
   intrusive changes of prog's BTF (useful for future linking), from Andrii Nakryiko.

5) Several BPF helper improvements e.g. avoid atomic op in cookie generator and add
   a redirect helper into neighboring subsys, from Daniel Borkmann.

6) Allow map updates on sockmaps from bpf_iter context in order to migrate sockmaps
   from one to another, from Lorenz Bauer.

7) Fix 32 bit to 64 bit assignment from latest alu32 bounds tracking which caused
   a verifier issue due to type downgrade to scalar, from John Fastabend.

8) Follow-up on tail-call support in BPF subprogs which optimizes x64 JIT prologue
   and epilogue sections, from Maciej Fijalkowski.

9) Add an option to perf RB map to improve sharing of event entries by avoiding remove-
   on-close behavior. Also, add BPF_PROG_TEST_RUN for raw_tracepoint, from Song Liu.

10) Fix a crash in AF_XDP's socket_release when memory allocation for UMEMs fails,
    from Magnus Karlsson.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

onfiguration'

Geert Uytterhoeven says:

====================
net/ravb: Add support for explicit internal clock delay configuration

Some Renesas EtherAVB variants support internal clock delay
configuration, which can add larger delays than the delays that are
typically supported by the PHY (using an "rgmii-*id" PHY mode, and/or
"[rt]xc-skew-ps" properties).

Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode.  This caused issues with PHY drivers that
implement PHY internal delays properly[1].  Hence a backwards-compatible
workaround was added by masking the PHY mode[2].

This patch series implements the next step of the plan outlined in [3],
and adds proper support for explicit configuration of the MAC internal
clock delays using new "[rt]x-internal-delay-ps" properties.  If none of
these properties is present, the driver falls back to the old handling.

This can be considered the MAC counterpart of commit 9150069b
("dt-bindings: net: Add tx and rx internal delays"), which applies to
the PHY.  Note that unlike commit 92252eec ("net: phy: Add a
helper to return the index for of the internal delay"), no helpers are
provided to parse the DT properties, as so far there is a single user
only, which supports only zero or a single fixed value.  Of course such
helpers can be added later, when the need arises, or when deemed useful
otherwise.

This series consists of 3 parts:
  1. DT binding updates documenting the new properties, for both the
     generic ethernet-controller and the EtherAVB-specific bindings,
  2. Conversion to json-schema of the Renesas EtherAVB DT bindings.
     Technically, the conversion is independent of all of the above.
     I included it in this series, as it shows how all sanity checks on
     "[rt]x-internal-delay-ps" values are implemented as DT binding
     checks,
  3. EtherAVB driver update implementing support for the new properties.

Given Rob has provided his acks for the DT binding updates, all of this
can be merged through net-next.

Changes compared to v3[4]:
  - Add Reviewed-by,
  - Drop the DT updates, as they will be merged through renesas-devel and
    arm-soc, and have a hard dependency on this series.

Changes compared to v2[5]:
  - Update recently added board DTS files,
  - Add Reviewed-by.

Changes compared to v1[6]:
  - Added "[PATCH 1/7] dt-bindings: net: ethernet-controller: Add
    internal delay properties",
  - Replace "renesas,[rt]xc-delay-ps" by "[rt]x-internal-delay-ps",
  - Incorporated EtherAVB DT binding conversion to json-schema,
  - Add Reviewed-by.

Impacted, tested:
  - Salvator-X(S) with R-Car H3 ES1.0 and ES2.0, M3-W, and M3-N.

Not impacted, tested:
  - Ebisu with R-Car E3.

Impacted, not tested:
  - Salvator-X(S) with other SoC variants,
  - ULCB with R-Car H3/M3-W/M3-N variants,
  - V3MSK and Eagle with R-Car V3M,
  - Draak with R-Car V3H,
  - HiHope RZ/G2[MN] with RZ/G2M or RZ/G2N,
  - Beacon EmbeddedWorks RZ/G2M Development Kit.

To ease testing, I have pushed this series and the DT updates to the
topic/ravb-internal-clock-delays-v4 branch of my renesas-drivers
repository at
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git.

Thanks for applying!

References:
  [1] Commit bcf3440c ("net: phy: micrel: add phy-mode support
      for the KSZ9031 PHY")
  [2] Commit 9b23203c ("ravb: Mask PHY mode to avoid inserting
      delays twice").
      https://lore.kernel.org/r/20200529122540.31368-1-geert+renesas@glider.be/
  [3] https://lore.kernel.org/r/CAMuHMdU+MR-2tr3-pH55G0GqPG9HwH3XUd=8HZxprFDMGQeWUw@mail.gmail.com/
  [4] https://lore.kernel.org/linux-devicetree/20200819134344.27813-1-geert+renesas@glider.be/
  [5] https://lore.kernel.org/linux-devicetree/20200706143529.18306-1-geert+renesas@glider.be/
  [6] https://lore.kernel.org/linux-devicetree/20200619191554.24942-1-geert+renesas@glider.be/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).

Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode.  This caused issues with PHY drivers that
implement PHY internal delays properly[1].  Hence a backwards-compatible
workaround was added by masking the PHY mode[2].

Add proper support for explicit configuration of the MAC internal clock
delays using the new "[rt]x-internal-delay-ps" properties.
Fall back to the old handling if none of these properties is present.

[1] Commit bcf3440c ("net: phy: micrel: add phy-mode support for
    the KSZ9031 PHY")
[2] Commit 9b23203c ("ravb: Mask PHY mode to avoid inserting
    delays twice").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, full delay handling is done in both the probe and resume
paths.  Split it in two parts, so the resume path doesn't have to redo
the parsing part over and over again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the Renesas Ethernet AVB (EthernetAVB-IF) Device Tree binding
documentation to json-schema.

Add missing properties.
Update the example to match reality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).

Add properties for configuring the internal MAC delays.
These properties are mandatory, even when specified as zero, to
distinguish between old and new DTBs.

Update the (bogus) example accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Internal Receive and Transmit Clock Delays are a common setting for
RGMII capable devices.

While these delays are typically applied by the PHY, some MACs support
configuring internal clock delay settings, too.  Hence add standardized
properties to configure this.

This is the MAC counterpart of commit 9150069b ("dt-bindings:
net: Add tx and rx internal delays"), which applies to the PHY.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-09-30

Updates and cleanups for mlx5 driver:

1) From Ariel, Dan Carpenter and Gostavo, Fixes to the previous
   mlx5 Connection track series.

2) From Yevgeny, trivial cleanups for Software steering

3) From Hamdan, Support for Flow source hint in software steering and
   E-Switch

4) From Parav and Sunil, Small and trivial E-Switch updates and
   cleanups in preparation for mlx5 Sub-functions support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Song Liu says:

====================
This set introduces BPF_F_PRESERVE_ELEMS to perf event array for better
sharing of perf event. By default, perf event array removes the perf event
when the map fd used to add the event is closed. With BPF_F_PRESERVE_ELEMS
set, however, the perf event will stay in the array until it is removed, or
the map is closed.
---
Changes v3 => v5:
1. Clean up in selftest. (Alexei)

Changes v2 => v3:
1. Move perf_event_fd_array_map_free() to avoid unnecessary forward
   declaration. (Daniel)

Changes v1 => v2:
1. Rename the flag as BPF_F_PRESERVE_ELEMS. (Alexei, Daniel)
2. Simplify the code and selftest. (Daniel, Alexei)
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Add tests for perf event array with and without BPF_F_PRESERVE_ELEMS.

Add a perf event to array via fd mfd. Without BPF_F_PRESERVE_ELEMS, the
perf event is removed when mfd is closed. With BPF_F_PRESERVE_ELEMS, the
perf event is removed when the map is freed.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200930224927.1936644-3-songliubraving@fb.com

Currently, perf event in perf event array is removed from the array when
the map fd used to add the event is closed. This behavior makes it
difficult to the share perf events with perf event array.

Introduce perf event map that keeps the perf event open with a new flag
BPF_F_PRESERVE_ELEMS. With this flag set, perf events in the array are not
removed when the original map fd is closed. Instead, the perf event will
stay in the map until 1) it is explicitly removed from the array; or 2)
the array is freed.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200930224927.1936644-2-songliubraving@fb.com

Calls to kzalloc() and kvzalloc() should be null-checked
in order to avoid any potential failures. In this case,
a potential null pointer dereference.

Fix this by adding null checks for _parse_attr_ and _flow_
right after allocation.

Addresses-Coverity-ID: 1497154 ("Dereference before null check")
Fixes: c620b772 ("net/mlx5: Refactor tc flow attributes structure")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

This code frees "shared_counter" and then dereferences on the next line
to get the error code.

Fixes: 1edae233 ("net/mlx5e: CT: Use the same counter for both directions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When removing a flow from the slow path fdb, a flow attr struct is
allocated for the rule removal process. If the allocation fails the
code prints a warning message but continues with the removal flow
which include dereferencing a pointer which could be null.
Fix this by exiting the function in case the attr allocation failed.

Fixes: c620b772 ("net/mlx5: Refactor tc flow attributes structure")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Use the PCI device directly for dma accesses as non PCI device unlikely
support IOMMU and dma mappings.
Introduce and use helper routine to access DMA device.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Set flow source as hint for local vport.
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently devlink eswitch ports are registered and unregistered by the
representor layer.
However it is better to register them at eswitch layer so that in future
user initiated command port add and delete commands can also
register/unregister devlink ports without depending on representor layer.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

To register and unregister devlink ports when loading/unload
representors, refactor the code to helper functions.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently only VF vports need egress ACL table.
Add a generic helper to check whether a vport need egress
ACL table or not.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently only 256 vports can be supported as only 8 bits are
reserved for them and 8 bits are reserved for vhca_ids in
metadata reg c0. To support more than 256 vports, replace
vhca_id with a unique shorter 4-bit PF number which covers
upto 16 PF's. Use remaining 12 bits for vports ranging 1-4095.
This will continue to generate unique metadata even if
multiple PCI devices have same switch_id.
Signed-off-by: sunils <sunils@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Skip the rule according to flow arrival source, in case of RX and the
source is local port skip and in case of TX and the source is uplink
skip, we get this info according to the flow source hint we get from
upper layers when creating the rule.
This is needed because for example in case of FDB table which has a TX
and RX tables and we are inserting a rule with an encap action which
is only a TX action, in this case rule will fail on RX, so we can rely
on the flow source hint and skip RX in such case.
Until now we relied on metadata regc_0 that upper layer mapped the
port in the regc_0, but the problem is that upper layer did not always
use regc_0 for port mapping, so now we added support to flow source
hint which upper layers will pass to SW steering when creating a rule.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Hamdan Igbaria <hamdani@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>