- 06 Mar, 2023 3 commits
-
-
Jani Nikula authored
Remove the leftover from moving and renaming the file from driver top level. Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/f11cbbdb5a5c8961fcae0b3f6c87860ee00f8c26.1677678803.git.jani.nikula@intel.com
-
Jani Nikula authored
Relatively few places need the DSC and DSS register definitions. Move them to intel_vdsc_regs.h. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230301151949.1591501-1-jani.nikula@intel.com
-
Jani Nikula authored
On TGL+ the DSS control registers are at different offsets, and there's one per pipe. Fix the offsets to fix dual link DSI for TGL+. There would be helpers for this in the DSC code, but just do the quick fix now for DSI. Long term, we should probably move all the DSS handling into intel_vdsc.c, so exporting the helpers seems counter-productive. Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8232 Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by:
-
- 01 Mar, 2023 4 commits
-
-
Ashutosh Dixit authored
The value shown by power1_max_interval in millisec is essentially: ((1.x * power(2,y)) * 1000) >> 10 Where x and y are read from a HW register. On ATSM, x and y are 0 on power-up so the value shown is 0. Writes of 0 to power1_max_interval had previously been disallowed to avoid computing ilog2(0) but this resulted in the corner-case bug below. Therefore allow writes of 0 now but special case that write to x = y = 0. Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7754Signed-off-by:
Ashutosh Dixit <ashutosh.dixit@intel.com> Reviewed-by:
Badal Nilawar <badal.nilawar@intel.com> Signed-off-by:
-
Ville Syrjälä authored
Fix the code to correctly determine whether delayed vblank is used or not. Signed-off-by:
Jouni Högander <jouni.hogander@intel.com>
-
Ville Syrjälä authored
The "window2" delay is just the difference of vactive (undelayed vblank) vs. vblank_start (delayed vblank). Just use vblank_start during the VRR calculations so that things work correctly regardless of whether delayed vblank is used or not. Signed-off-by:
-
Ville Syrjälä authored
Grab the HDR DPCD refresh timeout (time we need to wait after writing the sourc OUI before the HDR DPCD registers are ready) from the VBT. Windows doesn't even seem to have any default value for this, which is perhaps a bit weird since the VBT value is documented as TGL+ and I thought the HDR backlight stuff might already be used on earlier platforms. To play it safe I left the old hardcoded 30ms default in place. Digging through some internal stuff that seems to have been a number given by the vendor for one particularly slow TCON. Although I did see 50ms mentioned somewhere as well. Let's also include the value in the debug print to ease debugging, and toss in the customary connector id+name as well. The TGL Thinkpad T14 I have sets this to 0 btw. So the delay is now gone on this machine: [CONNECTOR:308:eDP-1] Detected Intel HDR backlight interface version 1 [CONNECTOR:308:eDP-1] Using Intel proprietary eDP backlight controls [CONNECTOR:308:eDP-1] SDR backlight is controlled through PWM [CONNECTOR:308:eDP-1] Using native PCH PWM for backlight control (controller=0) [CONNECTOR:308:eDP-1] Using AUX HDR interface for backlight control (range 0..496) [CONNECTOR:308:eDP-1] Performing OUI wait (0 ms) Cc: Lyude Paul <lyude@redhat.com> Signed-off-by:
-
- 27 Feb, 2023 1 commit
-
-
Matt Roper authored
The bspec was updated with a minor change to the 'DCC mode select' setting to be programmed during combo PHY initialization. v2: - Keep the opencoded rmw behavior instead of switching to intel_de_rmw(). We need to read from a _LN register, but write to the _GRP register to update all lanes. Bspec: 49291 Signed-off-by:
Matt Roper <matthew.d.roper@intel.com> Reviewed-by:
Matt Atwood <matthew.s.atwood@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230221201836.2886794-1-matthew.d.roper@intel.com
-
- 25 Feb, 2023 1 commit
-
-
Lucas De Marchi authored
Define MCR_REG() in the same header where i915_mcr_reg_t is defined, like i915_reg_t and _MMIO(). It's a more natural place for such a definition so it's not mixed with the registers for the platforms. Signed-off-by:
Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by:
-
- 24 Feb, 2023 3 commits
-
-
Rodrigo Vivi authored
These are left overs from the conversion towards intel_de_rmw. Fixes: aa80b2b1 ("drm/i915/display/panel: use intel_de_rmw if possible in panel related code") Cc: Andrzej Hajda <andrzej.hajda@intel.com> Signed-off-by:
Andrzej Hajda <andrzej.hajda@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230224153707.813953-1-rodrigo.vivi@intel.com
-
Ankit Nautiyal authored
Add snps phy table values for HDMI pixel clocks 267.30 MHz and 319.89 MHz. Values are based on the Bspec algorithm for PLL programming for HDMI. Cc: stable@vger.kernel.org Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8008Signed-off-by:
Ankit Nautiyal <ankit.k.nautiyal@intel.com> Reviewed-by:
Uma Shankar <uma.shankar@intel.com> Signed-off-by:
-
Jouni Högander authored
Currently we are using hardcoded 7 for io and fast wake lines. According to Bspec io and fast wake times are both 42us for DISPLAY_VER >= 12 and 50us and 32us for older platforms. Calculate line counts for these and configure them into PSR2_CTL accordingly Use 45 us for the fast wake calculation as 42 seems to be too tight based on testing. Bspec: 49274, 4289 Cc: Mika Kahola <mika.kahola@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Fixes: 64cf40a1 ("drm/i915/psr: Program default IO buffer Wake and Fast Wake") Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7725Signed-off-by:
Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230221085304.3382297-1-jouni.hogander@intel.com
-
- 23 Feb, 2023 8 commits
-
-
Ville Syrjälä authored
intel_dp_has_audio() has no need for the crtc_state, so don't pass it in. Signed-off-by:
-
Ville Syrjälä authored
I forgot to call intel_audio_compute_config() on DP MST, which means ELD doesn't get populated and passed to the audio driver. References: https://gitlab.freedesktop.org/drm/intel/-/issues/8097 Fixes: 5d986635 ("drm/i915/audio: Precompute the ELD") Signed-off-by:
-
Ville Syrjälä authored
FBC on gen2/3 seems to trigger page table errors. No visual artifacts are visible, and essentially the same FBC code works on gen4 so these seem entirely spurious. There are also hints in gen3 bspec indicating that certain bits in PGTBL_ER are just not wired up correctly in the hardware. Ideally we'd want to mask out only the bogus bits, but sadly there is no mask for PGTBL_ER, and instead we are forced to mask out all page table errors via EMR :( Signed-off-by:
Vinod Govindapillai <vinod.govindapillai@intel.com>
-
Ville Syrjälä authored
Pull the EMR calculation into small helpers. Signed-off-by:
-
Ville Syrjälä authored
PGTBL_ER contains the individual reasons for the page table error interrupt. Dump it out. Signed-off-by:
-
Ville Syrjälä authored
The gen2/gen3 irq code is supposed to be identical apart from the 32bit vs. 16bit access width. The recent change to intel_de_rmw() ruined that symmetry. Restore it to avoid needless mental gymnastics when comparing the two codepaths. And while at it remove the extra eir!=0 check that somehow ended up in the gen2 codepath only. Signed-off-by:
-
Ville Syrjälä authored
At least on some platforms (tested on ctg) the way vgacon does screen blanking seems to flag constant FIFO underruns, which means we have to be prepared for them while the driver is loading. Currently there is a time window between drm_crtc_init() and intel_sanitize_fifo_underrun_reporting() during which FIFO underrun reporting is in fact marked as enabled. Thus we may end up mistakenly detecting these bogus underruns during driver init. Close the race by marking FIFO underrun reporting as disabled prior to even registering the crtc. intel_sanitize_fifo_underrun_reporting()/etc. will re-enable it later if needed. Signed-off-by:
-
Ville Syrjälä authored
The audio logic lives in the transcoder rather than the pipe, so start tracking it like that. This is only really important for bigjoiner cases where tracking by pipe doesn't work at all since intel_audio_codec_{enable,disable}() won't even be called for the slave pipe. This means the state checker won't find the ELD for the slave pipe and gets upset. The PD->has_audio readout does currently work since that gets read out from the same transcoder for both pipes. For other cases this doesn't actually matter since it's only the normal pipe transcoders that are audio capable, whereas the more special transcoders (EDP/DSI) are not. v2: Fix kernel docs Signed-off-by:
-
- 21 Feb, 2023 1 commit
-
-
Andrzej Hajda authored
The helper makes the code more compact and readable. Signed-off-by:
-
- 20 Feb, 2023 8 commits
-
-
Ville Syrjälä authored
We just wrote the EDP transcoder's VTOTAL register a few lines earlier, so instead of reading it back out again let's just generate the same value for the transocder B/C register. Signed-off-by:
-
Ville Syrjälä authored
The DSI code has some local hacks to program TRANS_VBLANK on TGL+ (ICL DSI transcoders didn't have this register). That will not work when we need to start using the delayed vblank (for DSB purposes). Too lazy to figure out what the is going on there, so just sprinkle FIXMEs in the hopes someone else will spot them eventually. v2: Only TRANS_{HBLANK,SET_CONTEXT_LATENCY} still no not exist for DSI transcoders, only TRANS_VBLANK Signed-off-by: -
Ville Syrjälä authored
On TGL VBLANK.VBLANK_START was the mechanism by which we can delay the pipe's internal vblank in relation to the transcoder's vblank. On ADL+ that no longer does anything. Instead we must now use the new TRANS_SET_CONTEXT_LATENCY register. Program it accordingly. And since VBLANK.VBLANK_START is no longer used by the hardware on ADL+ let's just zero it out to make it stand out in register dumps. Seeing the zeroed value should hopefully remind people to check the other register instead. Signed-off-by:
-
Ville Syrjälä authored
If we have no LUTs to load there is no point in setting up the DSB command buffer. Signed-off-by:
Animesh Manna <animesh.manna@intel.com>
-
Ville Syrjälä authored
We'll be wanting to start the DSB from the vblank evasion critical section so printk()s are a big nono. Get rid of the debug print. Signed-off-by:
-
Ville Syrjälä authored
Allow the caller to ask for the DSB commands to execute during vblank. Signed-off-by:
-
Ville Syrjälä authored
Add definitions for more DSB registers. Less annoying spec trawling when working on the DSB code. Signed-off-by:
-
Ville Syrjälä authored
The PSR code has no business mucking around with the vblank delay. Currently nothing that depends on knowing the exact vblank start scanline (eg. vblank evasion) is aware of this and so will not work correctly. The w/a seems to be for pre-production hw only, so let's just nuke it. Signed-off-by:
-
- 17 Feb, 2023 11 commits
-
-
Ville Syrjälä authored
Define the contents of the transcoder timing registers using REG_GENMASK() & co. For ease of maintenance let's just define the bitmasks with the full 16bit width (also used by the current hand rolled stuff) even though not all bits are actually used. None of the unsued bits have ever contained anything. Jani spotted that the CRT load detection code did use narrower bitmasks, so that is now going to change. But that is fine since any garbage in the high bits would have been caught by the state checker that always used the full 16bit masks. Signed-off-by:
-
Ville Syrjälä authored
Clean up the eyesore in intel_get_transcoder_timings() a bit by adding a local 'adjusted_mode' variable. Signed-off-by:
-
Ville Syrjälä authored
On TGL+ the normal "start of vblank" interrupt is the pipe's (potentially delayed) version. Add the new bit for the transcoder's "unmodified" vblank so I don't have to dig it out from bspec every time. Signed-off-by:
-
Ville Syrjälä authored
With the delayed vblank we need to start knowing where the blanking periods start. So let's start dumping out also the blanking start/end timings. And while at it let's try to make that huge list of numbers somewhat legible by indicating what each value means. Also drop the 'type' since that doesn't really mean anything for the crtc_ timings. Signed-off-by:
-
Ville Syrjälä authored
Rename PIPECONF to TRANSCONF to make it clear what it actually applies to. While the usual convention is to pick the earliers name I think in this case it's more clear to use the later name. Especially as even the register offset is in the wrong range (0x70000 vs. 0x60000) and thus makes it look like this is per-pipe. There is one place in gvt that's doing something with TRANSCONF while iterating with for_each_pipe(). So that might not be doing the right thing for TRANSCODER_EDP, dunno. Not knowing what it does I left it as is to avoid breakage. Signed-off-by:
-
Ville Syrjälä authored
Name the CPU transcoder timing registers TRANS_FOO rather than just FOO. This is the modern name, after the pipe/transcoder split happened. Makes it a bit more obvious whether you pass in a pipe or a transcoder. PIPESRC is a bit special as it's a pipe register, even though it lives in the transcoder registers range (0x60000 instead of 0x70000). And BCLRPAT I suppose is a transcoder register (since it has something to do with the timing generator), but it doesn't even exist after gen4 so I left it to use the only name it ever had in bspec. And while at it let's pass in the correct enum in few more places why don't we. Although in all those places the distinction doesn't matter. Signed-off-by:
-
Ville Syrjälä authored
Use an early return to get rid of the extra indentation level in intel_ddi_{enable,disable}_transcoder_clock(). Also unify the platform handling in between the two while at it. Signed-off-by: -
Ville Syrjälä authored
What intel_ddi_{enable,disable}_pipe_clock() actually do is enable the clock to the transcoder, not the pipe. Rename accordingly. Signed-off-by: -
Ville Syrjälä authored
SKL/derivatives have DDI E but no AUX E, so we need to pick another aux ch as the platform default. DDI E is more or less the other half of DDI A, so we pick AUX A. In all other cases we should have a corresponding aux ch for each DDI. Signed-off-by:
-
Ville Syrjälä authored
Use encoder->name rather than port_name() in the debug messages so that they actually make more sense. Signed-off-by:
-
Ville Syrjälä authored
Restructure intel_bios_port_aux_ch() to resemble the ddc_pin counterpart, where the intel_bios.c stuff only deals with the child device definition, and the platform default will come from elsewhere. This requires the introduction of AUX_CH_NONE as the value 0 is already taken to mean AUX_CH_A. v2: Sort includes alphabetically (Ankit) vCould we ask them to do a BIOS fix for all of them so that we wouldn't keep getting these bug reports for each model separately? Signed-off-by:
-
