The start position for an ins instruction is always encoded as an
immediate, so allowing registers to be used by the inline asm makes no
sense. It should never happen anyway since a bit index should always be
small enough to be treated as an immediate, but remove the nonsensical
"r" for sanity.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Rather than #ifdef on CONFIG_CPU_* to determine whether the ins
instruction is supported we can simply check MIPS_ISA_REV to discover
whether we're targeting MIPSr2 or higher. Do so in order to clean up the
code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

set_bit() can set bits 0-15 using an ori instruction, rather than
loading the value -1 into a register & then using an ins instruction.

That is, rather than the following:

  li   t0, -1
  ll   t1, 0(t2)
  ins  t1, t0, 4, 1
  sc   t1, 0(t2)

We can have the simpler:

  ll   t1, 0(t2)
  ori  t1, t1, 0x10
  sc   t1, 0(t2)

The or path already allows immediates to be used, so simply restricting
the ins path to bits that don't fit in immediates is sufficient to take
advantage of this.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Reorder conditions in our various bitops functions that check
kernel_uses_llsc such that they handle the !kernel_uses_llsc case first.
This allows us to avoid the need to duplicate the kernel_uses_llsc check
in all the other cases. For functions that don't involve barriers common
to the various implementations, we switch to returning from within each
if block making each case easier to read in isolation.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Remove the remaining duplication between 32b & 64b in asm/atomic.h by
making use of an ATOMIC_OPS() macro to generate:

  - atomic_read()/atomic64_read()
  - atomic_set()/atomic64_set()
  - atomic_cmpxchg()/atomic64_cmpxchg()
  - atomic_xchg()/atomic64_xchg()

This is consistent with the way all other functions in asm/atomic.h are
generated, and ensures consistency between the 32b & 64b functions.

Of note is that this results in the above now being static inline
functions rather than macros.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Unify the definitions of atomic_sub_if_positive() &
atomic64_sub_if_positive() using a macro like we do for most other
atomic functions. This allows us to share the implementation ensuring
consistency between the two. Notably this provides the appropriate
loongson3_war barriers in the atomic64_sub_if_positive() case which were
previously missing.

The code is rearranged a little to handle the !kernel_uses_llsc case
first in order to de-indent the LL/SC case & allow us not to go over 80
characters per line.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Use smp_mb__before_atomic() & smp_mb__after_atomic() in
atomic_sub_if_positive() rather than the equivalent
smp_mb__before_llsc() & smp_llsc_mb(). The former are more standard &
this preps us for avoiding redundant duplicate barriers on Loongson3 in
a later patch.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Generate the sync instructions required to workaround Loongson3 LL/SC
errata within inline asm blocks, which feels a little safer than doing
it from C where strictly speaking the compiler would be well within its
rights to insert a memory access between the separate asm statements we
previously had, containing sync & ll instructions respectively.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Cut down on duplication by generalizing the ATOMIC_OP(),
ATOMIC_OP_RETURN() & ATOMIC_FETCH_OP() macros to work for both 32b &
64b atomics, and removing the ATOMIC64_ variants. This ensures
consistency between our atomic_* & atomic64_* functions.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Handle the !kernel_uses_llsc path first in our ATOMIC_OP(),
ATOMIC_OP_RETURN() & ATOMIC_FETCH_OP() macros & return from within the
block. This allows us to de-indent the kernel_uses_llsc path by one
level which will be useful when making further changes.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

We define macros in asm/atomic.h which end each line with space
characters before a backslash to continue on the next line. Remove the
space characters leaving tabs as the whitespace used for conformity with
coding convention.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Use the new __SYNC() infrastructure to implement sync_ginv(), for
consistency with much of the rest of the asm/barrier.h.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Implement __sync() using the new __SYNC() infrastructure, which will
take care of not emitting an instruction for old R3k CPUs that don't
support it. The only behavioral difference is that __sync() will now
provide a compiler barrier on these old CPUs, but that seems like
reasonable behavior anyway.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

The definition of fast_mb() is the same in both the Octeon & non-Octeon
cases, so remove the duplication & define it only once.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

We #ifdef on Cavium Octeon CPUs, but emit the same sync instruction in
both cases. Remove the #ifdef & simply expand to the __sync() macro.

Whilst here indent the strong ordering case definitions to match the
indentation of the weak ordering ones, helping readability.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Simplify our definitions of rmb() & wmb() using the new __SYNC()
infrastructure.

The fast_rmb() & fast_wmb() macros are removed, since they only provided
a level of indirection that made the code less readable & weren't
directly used anywhere in the kernel tree.

The Octeon #ifdef'ery is removed, since the "syncw" instruction
previously used is merely an alias for "sync 4" which __SYNC() will emit
for the wmb sync type when the kernel is configured for an Octeon CPU.
Similarly __SYNC() will emit nothing for the rmb sync type in Octeon
configurations.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

Introduce an asm/sync.h header which provides infrastructure that can be
used to generate sync instructions of various types, and for various
reasons. For example if we need a sync instruction that provides a full
completion barrier but only on systems which have weak memory ordering,
we can generate the appropriate assembly code using:

  __SYNC(full, weak_ordering)

When the kernel is configured to run on systems with weak memory
ordering (ie. CONFIG_WEAK_ORDERING is selected) we'll emit a sync
instruction. When the kernel is configured to run on systems with strong
memory ordering (ie. CONFIG_WEAK_ORDERING is not selected) we'll emit
nothing. The caller doesn't need to know which happened - it simply says
what it needs & when, with no concern for checking the kernel
configuration.

There are some scenarios in which we may want to emit code only when we
*didn't* emit a sync instruction. For example, some Loongson3 CPUs
suffer from a bug that requires us to emit a sync instruction prior to
each ll instruction (enabled by CONFIG_CPU_LOONGSON3_WORKAROUNDS). In
cases where this bug workaround is enabled, it's wasteful to then have
more generic code emit another sync instruction to provide barriers we
need in general. A __SYNC_ELSE() macro allows for this, providing an
extra argument that contains code to be assembled only in cases where
the sync instruction was not emitted. For example if we have a scenario
in which we generally want to emit a release barrier but for affected
Loongson3 configurations upgrade that to a full completion barrier, we
can do that like so:

  __SYNC_ELSE(full, loongson3_war, __SYNC(rl, always))

The assembly generated by these macros can be used either as inline
assembly or in assembly source files.

Differing types of sync as provided by MIPSr6 are defined, but currently
they all generate a full completion barrier except in kernels configured
for Cavium Octeon systems. There the wmb sync-type is used, and rmb
syncs are omitted, as has been the case since commit 6b07d38a
("MIPS: Octeon: Use optimized memory barrier primitives."). Using
__SYNC() with the wmb or rmb types will abstract away the Octeon
specific behavior and allow us to later clean up asm/barrier.h code that
currently includes a plethora of #ifdef's.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

When targeting MIPSr6 or higher make use of a compact branch in LL/SC
loops, preventing the insertion of a delay slot nop that only serves to
waste space.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

We currently duplicate the definition of __scbeqz in asm/atomic.h &
asm/cmpxchg.h. Move it to asm/llsc.h & rename it to __SC_BEQZ to fit
better with the existing __SC macro provided there.

We include a tab in the string in order to avoid the need for users to
indent code any further to include whitespace of their own after the
instruction mnemonic.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-kernel@vger.kernel.org

This patch adds support for the GARDENA smart Gateway, which is based on
the MediaTek MT7688 SoC. It is equipped with 128 MiB of DDR and 8 MiB of
flash (SPI NOR) and additional 128MiB SPI NAND storage.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@vger.kernel.org

This patch adds the vendor prefix for gardena and a short description
including the compatible string for the "GARDENA smart Gateway" based
on the MT7688 SoC.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@vger.kernel.org

This patch adds the "ralink,mt7688a-soc" compatible to the ralink DT
bindings documentation. This compatible is already used by some MIPS
boards (e.g. omega2p.dts) but not yet documented. It will also be used
by the upcoming "GARDENA smart Gateway" support.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@vger.kernel.org

This patch adds the I2C controller description to the MT7628A dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@vger.kernel.org

The r4k-bugs64 code will no longer be built for MIPSr6 kernel
configurations, so there's no need to perform checks for MIPSr6 within
the code. Drop those redundant checks.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org

Only build the checks for R4k errata workarounds if we expect that the
kernel might actually run on a system with an R4k CPU - ie.
CONFIG_SYS_HAS_CPU_R4X00=y & we're targeting a pre-MIPSr1 ISA revision.

Rename cpu-bugs64.c to r4k-bugs64.c to indicate the fact that the code
is specific to R4k CPUs.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org

Node ids don't need to be contiguous in Linux, so the concept to
use compact node ids to make them contiguous isn't needed at all.
This patchset therefore removes it.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

Most of the SN/SN0 header files are inherited from IRIX header files,
but not all of that stuff is useful for Linux. Remove not used parts.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

In commit 4ed28639 ("fs, elf: drop MAP_FIXED usage from elf_map") we
changed elf to use MAP_FIXED_NOREPLACE instead of MAP_FIXED for the
executable mappings.

Then, people reported that it broke some binaries that had overlapping
segments from the same file, and commit ad55eac7 ("elf: enforce
MAP_FIXED on overlaying elf segments") re-instated MAP_FIXED for some
overlaying elf segment cases.  But only some - despite the summary line
of that commit, it only did it when it also does a temporary brk vma for
one obvious overlapping case.

Now Russell King reports another overlapping case with old 32-bit x86
binaries, which doesn't trigger that limited case.  End result: we had
better just drop MAP_FIXED_NOREPLACE entirely, and go back to MAP_FIXED.

Yes, it's a sign of old binaries generated with old tool-chains, but we
do pride ourselves on not breaking existing setups.

This still leaves MAP_FIXED_NOREPLACE in place for the load_elf_interp()
and the old load_elf_library() use-cases, because nobody has reported
breakage for those. Yet.

Note that in all the cases seen so far, the overlapping elf sections
seem to be just re-mapping of the same executable with different section
attributes.  We could possibly introduce a new MAP_FIXED_NOFILECHANGE
flag or similar, which acts like NOREPLACE, but allows just remapping
the same executable file using different protection flags.

It's not clear that would make a huge difference to anything, but if
people really hate that "elf remaps over previous maps" behavior, maybe
at least a more limited form of remapping would alleviate some concerns.

Alternatively, we should take a look at our elf_map() logic to see if we
end up not mapping things properly the first time.

In the meantime, this is the minimal "don't do that then" patch while
people hopefully think about it more.
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: 4ed28639 ("fs, elf: drop MAP_FIXED usage from elf_map")
Fixes: ad55eac7 ("elf: enforce  MAP_FIXED on overlaying elf segments")
Cc: Michal Hocko <mhocko@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull dma-mapping regression fix from Christoph Hellwig:
 "Revert an incorret hunk from a patch that caused problems on various
  arm boards (Andrey Smirnov)"

* tag 'dma-mapping-5.4-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: fix false positive warnings in dma_common_free_remap()

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes this time around:

   - Fixup of some clock specifications for DRA7 (device-tree fix)

   - Removal of some dead/legacy CPU OPP/PM code for OMAP that throws
     warnings at boot

   - A few more minor fixups for OMAPs, most around display

   - Enable STM32 QSPI as =y since their rootfs sometimes comes from
     there

   - Switch CONFIG_REMOTEPROC to =y since it went from tristate to bool

   - Fix of thermal zone definition for ux500 (5.4 regression)"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: multi_v7_defconfig: Fix SPI_STM32_QSPI support
  ARM: dts: ux500: Fix up the CPU thermal zone
  arm64/ARM: configs: Change CONFIG_REMOTEPROC from m to y
  ARM: dts: am4372: Set memory bandwidth limit for DISPC
  ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
  ARM: OMAP2+: Add missing LCDC midlemode for am335x
  ARM: OMAP2+: Fix missing reset done flag for am3 and am43
  ARM: dts: Fix gpio0 flags for am335x-icev2
  ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
  ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
  DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
  ARM: dts: Fix wrong clocks for dra7 mcasp
  clk: ti: dra7: Fix mcasp8 clock bits

Merge tag 'kbuild-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - remove unneeded ar-option and KBUILD_ARFLAGS

 - remove long-deprecated SUBDIRS

 - fix modpost to suppress false-positive warnings for UML builds

 - fix namespace.pl to handle relative paths to ${objtree}, ${srctree}

 - make setlocalversion work for /bin/sh

 - make header archive reproducible

 - fix some Makefiles and documents

* tag 'kbuild-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kheaders: make headers archive reproducible
  kbuild: update compile-test header list for v5.4-rc2
  kbuild: two minor updates for Documentation/kbuild/modules.rst
  scripts/setlocalversion: clear local variable to make it work for sh
  namespace: fix namespace.pl script to support relative paths
  video/logo: do not generate unneeded logo C files
  video/logo: remove unneeded *.o pattern from clean-files
  integrity: remove pointless subdir-$(CONFIG_...)
  integrity: remove unneeded, broken attempt to add -fshort-wchar
  modpost: fix static EXPORT_SYMBOL warnings for UML build
  kbuild: correct formatting of header in kbuild module docs
  kbuild: remove SUBDIRS support
  kbuild: remove ar-option and KBUILD_ARFLAGS

Pull SCSI fixes from James Bottomley:
 "Twelve patches mostly small but obvious fixes or cosmetic but small
  updates"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla2xxx: Fix Nport ID display value
  scsi: qla2xxx: Fix N2N link up fail
  scsi: qla2xxx: Fix N2N link reset
  scsi: qla2xxx: Optimize NPIV tear down process
  scsi: qla2xxx: Fix stale mem access on driver unload
  scsi: qla2xxx: Fix unbound sleep in fcport delete path.
  scsi: qla2xxx: Silence fwdump template message
  scsi: hisi_sas: Make three functions static
  scsi: megaraid: disable device when probe failed after enabled device
  scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue
  scsi: qedf: Remove always false 'tmp_prio < 0' statement
  scsi: ufs: skip shutdown if hba is not powered
  scsi: bnx2fc: Handle scope bits when array returns BUSY or TSF

This makes getdents() and getdents64() do sanity checking on the
pathname that it gives to user space.  And to mitigate the performance
impact of that, it first cleans up the way it does the user copying, so
that the code avoids doing the SMAP/PAN updates between each part of the
dirent structure write.

I really wanted to do this during the merge window, but didn't have
time.  The conversion of filldir to unsafe_put_user() is something I've
had around for years now in a private branch, but the extra pathname
checking finally made me clean it up to the point where it is mergable.

It's worth noting that the filename validity checking really should be a
bit smarter: it would be much better to delay the error reporting until
the end of the readdir, so that non-corrupted filenames are still
returned.  But that involves bigger changes, so let's see if anybody
actually hits the corrupt directory entry case before worrying about it
further.

* branch 'readdir':
  Make filldir[64]() verify the directory entry filename is valid
  Convert filldir[64]() from __put_user() to unsafe_put_user()

This has been discussed several times, and now filesystem people are
talking about doing it individually at the filesystem layer, so head
that off at the pass and just do it in getdents{64}().

This is partially based on a patch by Jann Horn, but checks for NUL
bytes as well, and somewhat simplified.

There's also commentary about how it might be better if invalid names
due to filesystem corruption don't cause an immediate failure, but only
an error at the end of the readdir(), so that people can still see the
filenames that are ok.

There's also been discussion about just how much POSIX strictly speaking
requires this since it's about filesystem corruption.  It's really more
"protect user space from bad behavior" as pointed out by Jann.  But
since Eric Biederman looked up the POSIX wording, here it is for context:

 "From readdir:

   The readdir() function shall return a pointer to a structure
   representing the directory entry at the current position in the
   directory stream specified by the argument dirp, and position the
   directory stream at the next entry. It shall return a null pointer
   upon reaching the end of the directory stream. The structure dirent
   defined in the <dirent.h> header describes a directory entry.

  From definitions:

   3.129 Directory Entry (or Link)

   An object that associates a filename with a file. Several directory
   entries can associate names with the same file.

  ...

   3.169 Filename

   A name consisting of 1 to {NAME_MAX} bytes used to name a file. The
   characters composing the name may be selected from the set of all
   character values excluding the slash character and the null byte. The
   filenames dot and dot-dot have special meaning. A filename is
   sometimes referred to as a 'pathname component'."

Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.

Also note that if this ends up being noticeable as a performance
regression, we can fix that to do a much more optimized model that
checks for both NUL and '/' at the same time one word at a time.

We haven't really tended to optimize 'memchr()', and it only checks for
one pattern at a time anyway, and we really _should_ check for NUL too
(but see the comment about "soft errors" in the code about why it
currently only checks for '/')

See the CONFIG_DCACHE_WORD_ACCESS case of hash_name() for how the name
lookup code looks for pathname terminating characters in parallel.

Link: https://lore.kernel.org/lkml/20190118161440.220134-2-jannh@google.com/
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jann Horn <jannh@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We really should avoid the "__{get,put}_user()" functions entirely,
because they can easily be mis-used and the original intent of being
used for simple direct user accesses no longer holds in a post-SMAP/PAN
world.

Manually optimizing away the user access range check makes no sense any
more, when the range check is generally much cheaper than the "enable
user accesses" code that the __{get,put}_user() functions still need.

So instead of __put_user(), use the unsafe_put_user() interface with
user_access_{begin,end}() that really does generate better code these
days, and which is generally a nicer interface.  Under some loads, the
multiple user writes that filldir() does are actually quite noticeable.

This also makes the dirent name copy use unsafe_put_user() with a couple
of macros.  We do not want to make function calls with SMAP/PAN
disabled, and the code this generates is quite good when the
architecture uses "asm goto" for unsafe_put_user() like x86 does.

Note that this doesn't bother with the legacy cases.  Nobody should use
them anyway, so performance doesn't really matter there.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Fix ieeeu02154 atusb driver use-after-free, from Johan Hovold.

 2) Need to validate TCA_CBQ_WRROPT netlink attributes, from Eric
    Dumazet.

 3) txq null deref in mac80211, from Miaoqing Pan.

 4) ionic driver needs to select NET_DEVLINK, from Arnd Bergmann.

 5) Need to disable bh during nft_connlimit GC, from Pablo Neira Ayuso.

 6) Avoid division by zero in taprio scheduler, from Vladimir Oltean.

 7) Various xgmac fixes in stmmac driver from Jose Abreu.

 8) Avoid 64-bit division in mlx5 leading to link errors on 32-bit from
    Michal Kubecek.

 9) Fix bad VLAN check in rtl8366 DSA driver, from Linus Walleij.

10) Fix sleep while atomic in sja1105, from Vladimir Oltean.

11) Suspend/resume deadlock in stmmac, from Thierry Reding.

12) Various UDP GSO fixes from Josh Hunt.

13) Fix slab out of bounds access in tcp_zerocopy_receive(), from Eric
    Dumazet.

14) Fix OOPS in __ipv6_ifa_notify(), from David Ahern.

15) Memory leak in NFC's llcp_sock_bind, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
  selftests/net: add nettest to .gitignore
  net: qlogic: Fix memory leak in ql_alloc_large_buffers
  nfc: fix memory leak in llcp_sock_bind()
  sch_dsmark: fix potential NULL deref in dsmark_init()
  net: phy: at803x: use operating parameters from PHY-specific status
  net: phy: extract pause mode
  net: phy: extract link partner advertisement reading
  net: phy: fix write to mii-ctrl1000 register
  ipv6: Handle missing host route in __ipv6_ifa_notify
  net: phy: allow for reset line to be tied to a sleepy GPIO controller
  net: ipv4: avoid mixed n_redirects and rate_tokens usage
  r8152: Set macpassthru in reset_resume callback
  cxgb4:Fix out-of-bounds MSI-X info array access
  Revert "ipv6: Handle race in addrconf_dad_work"
  net: make sock_prot_memory_pressure() return "const char *"
  rxrpc: Fix rxrpc_recvmsg tracepoint
  qmi_wwan: add support for Cinterion CLS8 devices
  tcp: fix slab-out-of-bounds in tcp_zerocopy_receive()
  lib: textsearch: fix escapes in example code
  udp: only do GSO if # of segs > 1
  ...

Pull s390 fixes from Vasily Gorbik:

 - defconfig updates

 - Fix build errors with CC_OPTIMIZE_FOR_SIZE due to usage of "i"
   constraint for function arguments. Two kvm changes acked-by Christian
   Borntraeger.

 - Fix -Wunused-but-set-variable warnings in mm code.

 - Avoid a constant misuse in qdio.

 - Handle a case when cpumf is temporarily unavailable.

* tag 's390-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  KVM: s390: mark __insn32_query() as __always_inline
  KVM: s390: fix __insn32_query() inline assembly
  s390: update defconfigs
  s390/pci: mark function(s) __always_inline
  s390/mm: mark function(s) __always_inline
  s390/jump_label: mark function(s) __always_inline
  s390/cpu_mf: mark function(s) __always_inline
  s390/atomic,bitops: mark function(s) __always_inline
  s390/mm: fix -Wunused-but-set-variable warnings
  s390: mark __cpacf_query() as __always_inline
  s390/qdio: clarify size of the QIB parm area
  s390/cpumf: Fix indentation in sampling device driver
  s390/cpumsf: Check for CPU Measurement sampling
  s390/cpumf: Use consistant debug print format

__insn32_query() will not compile if the compiler decides to not
inline it, since it contains an inline assembly with an "i" constraint
with variable contents.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

The inline assembly constraints of __insn32_query() tell the compiler
that only the first byte of "query" is being written to. Intended was
probably that 32 bytes are written to.

Fix and simplify the code and just use a "memory" clobber.

Fixes: d6681397 ("KVM: s390: provide query function for instructions returning 32 byte")
Cc: stable@vger.kernel.org # v5.2+
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>