- 20 May, 2012 40 commits
-
-
Sakari Ailus authored
Implement more generic quirk registers than just limit and capability registers. This comes with the expense of a little bit more access time so these should be only used when really needed. Signed-off-by:
Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
Some sensors do use binning but do not have valid limits in binning registers. Use non-binning limits in that case. Signed-off-by:
-
Sakari Ailus authored
rval was not properly initialised in smiapp_read_nvm(). Do that. Signed-off-by:
-
Sakari Ailus authored
The pre_pll divisor must be such that ext_clk / pre_pll divisor does not result in a frequency that is greater than pll_ip_clk_freq. Fix this. Signed-off-by:
-
Sakari Ailus authored
Some sensors only allow 8-bit access, so use safe 8-bit access before the sensor has been identified. Signed-off-by:
-
Sakari Ailus authored
Some sensors implement only 8-bit read functionality and fail on wider reads. Add a quirk flag for such sensors. Signed-off-by:
-
Sakari Ailus authored
Pass struct sensor to register access commands. This allows taking quirks into account in register access. Signed-off-by:
-
Sakari Ailus authored
Instead of providing a function in platform data, allow also providing the name of the external clock and use it through the clock framework. Signed-off-by:
-
Antti Palosaari authored
Report SNR in 0.1 dB scale instead of raw hardware register values. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Jozsef Marton authored
gspca_pac7302 module supports the webcam with usb id: 093a:2627. It is a Genius FaceCam 300. The module does not need any changes but listing the usb id along with a vertical flip flag. The included patch adds this to the module source. Signed-off-by:
Jozsef Marton <jmarton@users.sourceforge.net> Acked-by:
Márton Németh <nm127@freemail.hu> Signed-off-by:
-
Malcolm Priestley authored
Continuous flip of bit2 reg 0x70 can cause device to become unresponsive. Also correct reg read mistake. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
-
Igor M. Liplianin authored
Trival patch to get it working with my cards stuff. Signed-off-by:
Igor M. Liplianin <liplianin@me.by> Acked-by:
-
Mauro Carvalho Chehab authored
This device supports V4L2_STD_ALL, but its check for 60Hz standards is broken, as NTSC is not the only standard that uses 60Hz. Cc: Federico Vaga <federico.vaga@gmail.com> Signed-off-by: -
Federico Vaga authored
V4L2 driver for the Video Input Port within STA2X11 board Signed-off-by:
Federico Vaga <federico.vaga@gmail.com> Acked-by:
Giancarlo Asnaghi <giancarlo.asnaghi@st.com> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Federico Vaga authored
Signed-off-by:
-
Federico Vaga authored
Video user controls such as brightness, contrast, saturation, and hue are now handled. Signed-off-by:
-
Ben Hutchings authored
fintek-cir, ite-cir and nuvoton-cir may try to free an I/O region and/or IRQ handler that was never allocated after a failure in their respective probe functions. Add and use separate labels on the failure path so they will do the right cleanup after each possible point of failure. Compile-tested only. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Malcolm Priestley authored
Correct incorrect scancode for KEY_1 Signed-off-by:
-
Anssi Hannula authored
There are many different Medion X10 remotes that need slightly different keymaps. We may not yet have all the needed keymaps, in which case a wrong keymap may be used. This happened with Medion X10 OR2x remotes before the keymap for them was added, causing the ati_remote driver to select the Medion Digitainer keymap instead. Unfortunately, the Medion Digitainer keymap doesn't have the standard X10 up/down scancodes assigned to KEY_UP and KEY_DOWN keycodes, making wrongly assigned remotes mostly unusable. Add the regular KEY_UP and KEY_DOWN scancodes to the Medion X10 Digitainer keymap, making any Medion remote mostly usable even when wrongly used with that keymap (standard buttons, such as up/down/left/right, 0-9, play/stop/pause, have the same scancode in all the X10 remotes). Signed-off-by:
Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by:
-
Anssi Hannula authored
Add another Medion X10 remote keymap. This is for the Medion OR2x remotes with the Windows MCE button. The receiver shipped with this remote has the same USB ID as the other Medion receivers, but the name is different and is therefore used to detect this variant. Signed-off-by:
-
Mauro Carvalho Chehab authored
This patch were applied by mistake, as it were rejected by Don, who requested it to be broken into per-change patches. This reverts commit 0982db20. Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Volokh Konstantin <volokh84@gmail.com> Signed-off-by:
-
joseph daniel authored
There was a warning when ran "make versioncheck" drivers/staging/media/as102/as102_fe.c: 20 linux/version.h not needed. Signed-off-by:
joseph daniel <josephdanielwalter@gmail.com> Signed-off-by:
-
Igor M. Liplianin authored
The card is similar to TeVii s470, but has different LNB power control. Signed-off-by:
-
Laurent Pinchart authored
The Logitech pan/tilt reset UVC control contains two V4L2 button controls to reset pan and tilt. As the UVC control is not marked as auto-update, the button bits are set but never reset. A pan reset that follows a tilt reset would thus reset both pan and tilt. Fix this by not caching the control value of write-only controls. All standard UVC controls are either readable or auto-update, so this will not cause any regression and will not result in extra USB requests. Reported-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
-
Ismael Luceno authored
Tested with Yfeng 680 ATV dongle. Signed-off-by:
Ismael Luceno <ismael.luceno@gmail.com> Signed-off-by:
-
Volokh Konstantin authored
This issuses applyed only for Adlink MPG24 board with go7007 & wis2804, all whese changes was tested for continuos load&restart mode This is minimal changes needed for start up go7007&wis2804 to work correctly in 3.4 branch Changes: - When go7007 reset device, i2c was not worked (need rewrite GPIO5) - As wis2804 has i2c_addr=0x00/*really*/, so Need set I2C_CLIENT_TEN flag for validity - some main nonzero initialization, rewrites with kzalloc instead kmalloc - STATUS_SHUTDOWN was placed in incorrect place, so if firmware wasn`t loaded, we failed v4l2_device_unregister with kernel panic (OOPS) - some new v4l2 style features as call_all(...s_stream...) for using subdev calls - wis-tw2804.ko module code was incompatible with 3.4 branch in initialization v4l2_subdev parts. now i2c_get_clientdata(...) contains v4l2_subdev struct instead non standart wis_tw2804 struct Adds: - Additional chipset tw2804 controls with: gain,auto gain,inputs[0,1],color kill,chroma gain,gain balances, for all 4 channels (from tw2804.pdf) - Power control for each 4 ADC (tw2804) up when s_stream(...,1), down otherwise Signed-off-by:Volokh Konstantin <volokh84@gmail.com> Signed-off-by:
-
Antti Palosaari authored
Demod needs some time to wake up after power on. Signed-off-by:
-
Antti Palosaari authored
to prevent I/O errors... Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Reports value as a 0.1 dB. Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
UIO-2 and UIO-3 were broken. Signed-off-by:
-
Hans-Frieder Vogt authored
Changes compared to version 0.1 of driver (sent 6 May): - Initial implementation of get_rf_strength function. - Introduction of a warning message Signed-off-by:
Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by:
-
Hans-Frieder Vogt authored
Changes compared to version 0.5 of driver (sent 6 May): - Initial implementation of get_rf_strength function. Signed-off-by:
-
Hans-Frieder Vogt authored
Support for tuner Fitipower FC0013 Signed-off-by:
-
Hans-Frieder Vogt authored
Support for tuner Fitipower FC0012 Signed-off-by:
-
Hans-Frieder Vogt authored
Common defines for the FC0012 (v0.5) and FC0013 tuner drivers Signed-off-by:
-
Mauro Carvalho Chehab authored
drivers/media/dvb/frontends/lg2160.c: In function ‘lg216x_read_ucblocks’: drivers/media/dvb/frontends/lg2160.c:1336:1: warning: label ‘fail’ defined but not used [-Wunused-label] drivers/media/dvb/frontends/lg2160.c:1325:6: warning: unused variable ‘ret’ [-Wunused-variable] drivers/media/dvb/frontends/lg2160.c:1324:23: warning: unused variable ‘state’ [-Wunused-variable] drivers/media/dvb/frontends/lg2160.c: In function ‘lg216x_set_ensemble’: drivers/media/dvb/frontends/lg2160.c:420:23: warning: ‘reg’ may be used uninitialized in this function [-Wuninitialized] Cc: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
