I found a problem of handling of modem status of atmel_serial driver.

With the commit 1ecc26 ("atmel_serial: split the interrupt handler"),
handling of modem status signal was splitted into two parts.  The
atmel_tasklet_func() compares new status with irq_status_prev, but
irq_status_prev is not correct if signal status was changed while the port
is closed.

Here is a sequence to cause problem:

1. Remote side sets CTS (and DSR).
2. Local side close the port.
3. Local side clears RTS and DTR.
4. Remote side clears CTS and DSR.
5. Local side reopen the port.  hw_stopped becomes 1.
6. Local side sets RTS and DTR.
7. Remote side sets CTS and DSR.

Then CTS change interrupt can be received, but since CTS bit in
irq_status_prev and new status is same, uart_handle_cts_change() will not
be called (so hw_stopped will not be cleared, i.e.  cannot send any data).

I suppose irq_status_prev should be initialized at somewhere in open
sequence.

Itai Levi pointed out that we need to initialize atmel_port->irq_status
as well here. His analysis is as follows:

> Regarding the second part of the patch (which resets irq_status_prev),
> it turns out that both versions of the patch (mine and Atsushi's)
> still leave enough room for faulty behavior when opening the port.
>
> This is because we are not resetting both irq_status_prev and
> irq_status in atmel_startup() to CSR, which leads faulty behavior in
> the following sequences:
>
> First case:
> 1. closing the port while CTS line = 1 (TX not allowed)
> 2. setting CTS line = 0 (TX allowed)
> 3. opening the port
> 4. transmitting one char
> 5. Cannot transmit more chars, although CTS line is 0
>
> Second case:
> 1. closing the port while CTS line = 0 (TX allowed)
> 2. setting CTS line = 1 (TX not allowed)
> 3. opening the port
> 4. receiving some chars
> 5. Now we can transmit, although CTS line is 1
>
> This reason for this is that the tasklet is scheduled as a result of
> TX or RX interrupts (not a status change!), in steps 4 above. Inside
> the tasklet, the atmel_port->irq_status (which holds the value from
> the previous session) is compared to atmel_port->irq_status_prev.
> Hence, a status-change of the CTS line is faultily detected.
>
> Both cases were verified on 9260 hardware.

[haavard.skinnemoen@atmel.com: folded with patch from Itai Levi]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: Itai Levi <itai.levi.devel@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The conversion of atmel-mci to dma_request_channel missed the
initialization of the channel dma_slave information.  The filter_fn passed
to dma_request_channel is responsible for initializing the channel's
private data.  This implementation has the additional benefit of enabling
a generic client-channel data passing mechanism.
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add support for HP Pavilion dv5.

Since Intel-based models have an inverted x axis, while AMD-based models
have an inverted y axis, we introduce a new macro that special-cases axis
orientation based on two DMI entries: HP dv5 axis configuration is then
based on both the PRODUCT and BOARD name.
Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Cc: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Tested-by: Palatis Tseng <palatis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Sensors responding with 0x3B to WHO_AM_I only have one data register per
direction, thus returning a signed byte from the position which is
occupied by the MSB in sensors responding with 0x3A.

Since multiple sensors share the reply to WHO_AM_I, we rename the defines
to better indicate what they identify (family of single and double
precision sensors).

We support both kind of sensors by checking for the sensor type on init
and defining appropriate data-access routines and sensor limits (for the
joystick) depending on what we find.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Acked-by: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This adds freefall handling to hp_accel driver.  According to HP, it
should just work, without us having to set the chip up by hand.

hpfall.c is example .c program that parks the disk when accelerometer
detects free fall.  It should work; for now, it uses fixed 20seconds
protection period.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Otherwise with INPUT=m, EEEPC_LAPTOP=y one gets

drivers/built-in.o: In function `input_sync':
eeepc-laptop.c:(.text+0x18ce51): undefined reference to `input_event'
drivers/built-in.o: In function `input_report_key':
eeepc-laptop.c:(.text+0x18ce73): undefined reference to `input_event'
drivers/built-in.o: In function `eeepc_hotk_check':
eeepc-laptop.c:(.text+0x18d05f): undefined reference to `input_allocate_device'
eeepc-laptop.c:(.text+0x18d10f): undefined reference to `input_register_device'
eeepc-laptop.c:(.text+0x18d131): undefined reference to `input_free_device'
drivers/built-in.o: In function `eeepc_backlight_exit':
eeepc-laptop.c:(.text+0x18d546): undefined reference to `input_unregister_device'
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Compilation of kprobes.c with CONFIG_PM unset is broken due to some broken
config dependncies.  Fix that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In cgroup_kill_sb(), root is freed before sb is detached from the list, so
another sget() may find this sb and call cgroup_test_super(), which will
access the root that has been freed.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

YAMAMOTO-san noticed that task_dirty_inc doesn't seem to be called properly for
cases where set_page_dirty is not used to dirty a page (eg. mark_buffer_dirty).

Additionally, there is some inconsistency about when task_dirty_inc is
called.  It is used for dirty balancing, however it even gets called for
__set_page_dirty_no_writeback.

So rather than increment it in a set_page_dirty wrapper, move it down to
exactly where the dirty page accounting stats are incremented.

Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As requested by Michael, add a missing check for valid flags in
timerfd_settime(), and make it return EINVAL in case some extra bits are
set.

Michael said:
If this is to be any use to userland apps that want to check flag
support (perhaps it is too late already), then the sooner we get it
into the kernel the better: 2.6.29 would be good; earlier stables as
well would be even better.

[akpm@linux-foundation.org: remove unused TFD_FLAGS_SET]
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org>		[2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

My @suse.cz address will stop working some day, so put working one into
MAINTAINERS/CREDITS.  It would be cool to get this to 2.6.29...  it should
not really break anything.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently seq_read assumes that the offset passed to it is always the
offset it passed to user space.  In the case pread this assumption is
broken and we do the wrong thing when presented with pread.

To solve this I introduce an offset cache inside of struct seq_file so we
know where our logical file position is.  Then in seq_read if we try to
read from another offset we reset our data structures and attempt to go to
the offset user space wanted.

[akpm@linux-foundation.org: restore FMODE_PWRITE]
[pjt@google.com: seq_open needs its fmode opened up to take advantage of this]
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Paul Turner <pjt@google.com>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Separate FMODE_PREAD and FMODE_PWRITE into separate flags to reflect the
reality that the read and write paths may have independent restrictions.

A git grep verifies that these flags are always cleared together so this
new behavior will only apply to interfaces that change to clear flags
individually.

This is required for "seq_file: properly cope with pread", a post-2.6.25
regression fix.

[akpm@linux-foundation.org: add comment]
Signed-off-by: Paul Turner <pjt@google.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc:  Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The css_set hash table was introduced in 2.6.26, so update the
documentation accordingly.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The Welland ME-747K-SI AoE target generates unsolicited AoE responses that
are marked as vendor extensions.  Instead of ignoring these packets, the
aoe driver was generating kernel messages for each unrecognized response
received.  This patch corrects the behavior.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Reported-by: <karaluh@karaluh.pl>
Tested-by: <karaluh@karaluh.pl>
Cc: <stable@kernel.org>
Cc: Alex Buell <alex.buell@munted.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We have get_vm_area_caller() and __get_vm_area() but not
__get_vm_area_caller()

On powerpc, I use __get_vm_area() to separate the ranges of addresses
given to vmalloc vs.  ioremap (various good reasons for that) so in order
to be able to implement the new caller tracking in /proc/vmallocinfo, I
need a "_caller" variant of it.

(akpm: needed for ongoing powerpc development, so merge it early)

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If a USB PCI controller is behind a cardbus bridge, we are trying to
restore its configuration registers too early, before the cardbus
bridge is operational.  To fix this, call pci_restore_state() from
usb_hcd_pci_resume() and remove usb_hcd_pci_resume_early() which is
no longer necessary (the configuration spaces of USB controllers that
are not behind cardbus bridges will be restored by the PCI PM core
with interrupts disabled anyway).

This patch fixes the regression from 2.6.28 tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12659

[ Side note: the proper long-term fix is probably to just force the
  unplug event at suspend time instead of doing a plug/unplug at resume
  time, but this patch is fine regardless  - Linus ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: cpu hotplug fix

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  timers: more consistently use clock vs timer

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  doc: mmiotrace.txt, buffer size control change
  trace: mmiotrace to the tracer menu in Kconfig
  mmiotrace: count events lost due to not recording

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, vm86: fix preemption bug
  x86, olpc: fix model detection without OFW
  x86, hpet: fix for LS21 + HPET = boot hang
  x86: CPA avoid repeated lazy mmu flush
  x86: warn if arch_flush_lazy_mmu_cpu is called in preemptible context
  x86/paravirt: make arch_flush_lazy_mmu/cpu disable preemption
  x86, pat: fix warn_on_once() while mapping 0-1MB range with /dev/mem
  x86/cpa: make sure cpa is safe to call in lazy mmu mode
  x86, ptrace, mm: fix double-free on race

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  iommu: fix Intel IOMMU write-buffer flushing
  futex: fix reference leak

Trivial conflicts fixed manually in drivers/pci/intel-iommu.c

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/vsx: Fix VSX alignment handler for regs 32-63
  powerpc/ps3: Move ps3_mm_add_memory to device_initcall
  powerpc/mm: Fix numa reserve bootmem page selection
  powerpc/mm: Fix _PAGE_CHG_MASK to protect _PAGE_SPECIAL

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: Documentation: fix minor PCIe HOWTO thinko
  PCI: fix missing kernel-doc and typos
  PCI: fix struct pci_platform_pm_ops kernel-doc
  PCI: fix rom.c kernel-doc warning
  PCI/MSI: fix msi_mask() shift fix

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: lrw - Fix big endian support

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: hold trans_mutex when using btrfs_record_root_in_trans
  Btrfs: make a lockdep class for the extent buffer locks
  Btrfs: fs/btrfs/volumes.c: remove useless kzalloc
  Btrfs: remove unused code in split_state()
  Btrfs: remove btrfs_init_path
  Btrfs: balance_level checks !child after access
  Btrfs: Avoid using __GFP_HIGHMEM with slab allocator
  Btrfs: don't clean old snapshots on sync(1)
  Btrfs: use larger metadata clusters in ssd mode
  Btrfs: process mount options on mount -o remount,
  Btrfs: make sure all pending extent operations are complete

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_nv: give up hardreset on nf2
  libata-sff: fix 32-bit PIO ATAPI regression

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  kbuild: create the source symlink earlier in the objdir
  scripts: add x86 64 bit support to the markup_oops.pl script
  scripts: add x86 register parser to markup_oops.pl
  kbuild: add sys_* entries for syscalls in tags
  kbuild: fix tags generation of config symbols
  bootgraph: fix for use with dot symbols
  kbuild: add vmlinux to kernel rpm
  kbuild,setlocalversion: shorten the make time when using svn

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  MAINTAINERS: Switch hdaps to Frank Seidel
  hwmon: Fix ACPI resource check error handling
  hwmon: (f71882fg) Hide misleading error message

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB (10626): ivtv: fix regression in get sliced vbi format
  V4L/DVB (10625): ivtv: fix decoder crash regression
  V4L/DVB (10619): gspca - main: Destroy the URBs at disconnection time.
  V4L/DVB (10572): Revert commit dda06a8e
  V4L/DVB (10533): fix LED status output
  V4L/DVB (10532): Correction of Stereo detection/setting and signal strength indication
  V4L/DVB (10527): tuner: fix TUV1236D analog/digital setup
  V4L/DVB (10516a): zoran: Update MAINTAINERS entry

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: fix bus endianity in file2alias
  HID: move tmff and zpff devices from ignore_list to blacklist
  HID: unlock properly on error paths in hidraw_ioctl()
  HID: blacklist Powercom USB UPS

* 'for-linus' of git://git.o-hand.com/linux-mfd:
  mfd: Fix sm501_register_gpio section mismatch
  mfd: fix sm501 section mismatches
  mfd: terminate pcf50633 i2c_device_id list
  mfd: Ensure all WM8350 IRQs are masked at startup
  mfd: fix htc-egpio iomem resource handling using resource_size
  mfd: Fix TWL4030 build on some ARM variants
  mfd: wm8350 tries reaches -1
  mfd: Mark WM835x USB_SLV_500MA bit as accessible
  mfd: Improve diagnostics for WM8350 ID register probe
  mfd: Initialise WM8350 interrupts earlier
  mfd: Fix egpio kzalloc return test

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] iTCO_wdt: fix SMI_EN regression 2

* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
  wusb: whci-hcd: always lock whc->lock with interrupts disabled

The macro doesn't expand correctly when its parameter isn't 'pte'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: Fix NULL dereference in ext4_ext_migrate()'s error handling
  ext4: Implement range_cyclic in ext4_da_writepages instead of write_cache_pages
  ext4: Initialize preallocation list_head's properly
  ext4: Fix lockdep warning
  ext4: Fix to read empty directory blocks correctly in 64k
  jbd2: Avoid possible NULL dereference in jbd2_journal_begin_ordered_truncate()
  Revert "ext4: wait on all pending commits in ext4_sync_fs()"
  jbd2: Fix return value of jbd2_journal_start_commit()

* 'kvm-updates/2.6.29' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: VMX: Flush volatile msrs before emulating rdmsr
  KVM: Fix assigned devices circular locking dependency
  KVM: x86: fix LAPIC pending count calculation
  KVM: Fix INTx for device assignment
  KVM: MMU: Map device MMIO as UC in EPT
  KVM: x86: disable kvmclock on non constant TSC hosts
  KVM: PIT: fix i8254 pending count read
  KVM: Fix racy in kvm_free_assigned_irq
  KVM: Add kvm_arch_sync_events to sync with asynchronize events
  KVM: mmu_notifiers release method
  KVM: Avoid using CONFIG_ in userspace visible headers
  KVM: ia64: fix fp fault/trap handler

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  cpumask: Use cpu_*_mask accessors code: alpha
  cpumask: fix powernow-k8: partial revert of 2fdf66b4

This is the cause of the DMA faults and disk corruption that people have
been seeing. Some chipsets neglect to report the RWBF "capability" --
the flag which says that we need to flush the chipset write-buffer when
changing the DMA page tables, to ensure that the change is visible to
the IOMMU.

Override that bit on the affected chipsets, and everything is happy
again.

Thanks to Chris and Bhavesh and others for helping to debug.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>