Magnus Damm says:

====================
ravb: Duplex handling update V3

[PATCH v3 01/02] ravb: Do not announce HDX as supported
[PATCH v3 02/02] ravb: Clean up duplex handling

This series is V3 of duplex handling improvements for the Ethernet-AVB driver.

Previous versions of this series have been posted to linux-renesas-soc as RFC
so V3 is the first actual version to make it to netdev.

Based on the latest data sheet for R-Car Gen3 [1] and R-Car Gen2 [2]
the following information is part of the EthernetAVB-IF overview page:

Transfer speed: Supports transfer at 100 and 1000 Mbps
Mode: Full-duplex mode

It seems that the driver implementation is not matching the information
provided in the friendly data sheet, and on top of this during run-time
when changing PHY configuration of the link partner the Ethernet-AVB PHY
seems to want to announce unsupported modes.

[1] R-Car Series, 3rd Generation Rev.1.00 (Apr 2018)
[2] R-Car Series, 2nd Generation Rev.2.00 (Feb 2016)

Changes since V2:
- Updated patch 1/2 to make use of phy_remove_link_mode()
- Added Reviewed-by from Sergei - thanks!

Changes since V1:
- Updated patches to reflect input from Sergei and Geert - thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since only full-duplex operation is supported by the
hardware, remove duplex handling code and keep the
register setting of ECMR.DM fixed at 1.

This updates the driver implementation to follow the
data sheet text "This bit should always be set to 1."

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the data sheet the Ethernet-AVB hardware in R-Car Gen3
and R-Car Gen2 SoCs do not support half duplex operation. So update
the driver to mark 100Mbit and 1Gbps HDX as unsupported.

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the fw supports returning VIN/VIVLD in FW_VI_CMD save it
in port_info structure else retrieve these from viid and save
them  in port_info structure. Do the same for smt_idx from
FW_VI_MAC_CMD
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit c5a54bbc ("net: bcmgenet: abort suspend on error")
mistakenly introduced register accesses that should not occur
in bcmgenet_wol_power_up_cfg().

Fixes: c5a54bbc ("net: bcmgenet: abort suspend on error")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Perform CQ initialization in the driver when the capability is supported
by the FW.  When passing the CQ to HW indicate that the CQ buffer has
been pre-initialized.

Doing so decreases CQ creation time.  Testing on P8 showed a single 2048
entry CQ creation time was reduced from ~395us to ~170us, which is
2.3x faster.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 3327a9c4 ("selftests: add functionals test for UDP GRO")
make use of ipv6 NAT, but such a feature is not currently implied by
selftests. Since the 'ip[6]tables' commands may actually create nft rules,
depending on the specific user-space version, let's pull both NF and
NFT nat modules plus the needed deps.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 3327a9c4 ("selftests: add functionals test for UDP GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Add VxLAN learning support

This patchset adds VxLAN learning support in the mlxsw driver.

The first five patches from Petr add the required switchdev APIs which
allow device drivers to notify the VxLAN driver about learned / aged-out
FDB entries.

First in patch #1, an unnecessary argument is dropped from
__vxlan_fdb_delete().

In patches #2-#4, the VxLAN FDB handling code is extended to make
sending the switchdev events configurable; to mark user-added entries as
such; and to make sure HW-learned FDB entries do not take over
user-added ones.

Finally in patch #5, the necessary switchdev notifications are added and
handled by VxLAN, similarly to how this is handled in the bridge driver.

Patch #6 allows changing of the VxLAN's device ageing time since it is
useful for the selftest in the last patch.

Patch #7 adds support for querying bridge port flags of a given
netdevice, as a new entry should not be learned and notified to the
bridge driver in case learning is disabled on the bridge port.

Next patches gradually add learning support in mlxsw.

The last patch adds a new test case for VxLAN learning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test which checks that the VxLAN driver can learn FDB entries and
that these entries are correctly deleted and aged-out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The test currently expects that a configuration which includes a VxLAN
device with learning enabled to fail.

Previous patches enabled VxLAN learning in mlxsw, so change the test
accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up until now the driver returned an error when learning was enabled on a
VxLAN device enslaved to an offloaded bridge.

Previous patches added VxLAN learning support, so remove the check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow users to delete learned FDB entries from the bridge's FDB before
enabling VxLAN learning.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Start processing two new entry types in addition to current ones:
* Learned unicast tunnel entry
* Aged-out unicast tunnel entry

In both cases the device reports on a new {MAC, FID, IP address} tuple
that was learned / aged-out. Based on this notification, the driver
instructs the device to add / delete the entry to / from its database.

The driver also makes sure to notify the bridge and VxLAN drivers about
the new entry.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FDB notifications for entries learned from an NVE tunnel contain the IP
address of the remote VTEP. In the case of IPv4 underlay, the IP address
is specified as-is. IPv6 addresses on the other hand, are specified as
handles which then need to be used to query the actual address from the
device.

Only IPv4 underlay is currently supported, so we cannot receive
notifications for IPv6 addresses and therefore an error is returned when
one tries to resolve such an address.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When processing a notification about a new FDB entry learned from a
VxLAN tunnel, the driver is provided with the FID index among other
parameters.

The driver potentially needs to update the bridge and VxLAN drivers
about the new entry using a pointer to the VxLAN device and the
corresponding VNI.

These two parameters are stored in the FID, so add a new function that
allows looking up a FID based on its index.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver periodically polls for new FDB entries learned by the device.
In the case of an FDB entry learned from a VxLAN tunnel, the
notification includes the IP of the remote VTEP, the filtering
identifier (FID) and the source MAC address of the overlay packet.

Assuming learning is enabled in the VxLAN and bridge drivers, the driver
needs to generate a notification and update them about the new FDB
entry.

Store the ifindex of the NVE device in the FID so that the driver will
be able to update the VxLAN and bridge drivers using it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Will be used to process learned FDB records from an NVE tunnel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow querying bridge port flags so that drivers capable of performing
VxLAN learning will update the bridge driver only if learning is enabled
on its bridge port corresponding to the VxLAN device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a similar fashion to the bridge device, allow changing the ageing
time of the VxLAN device by scheduling its timer to fire if the ageing
time changed.

One use case is selftests where learning / ageing of VxLAN FDB entries
is tested. The default ageing time is 5 minutes, which is too long for a
simple selftest.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to allow devices to signal learning events to VXLAN, introduce
two new switchdev messages: SWITCHDEV_VXLAN_FDB_ADD_TO_BRIDGE and
SWITCHDEV_VXLAN_FDB_DEL_TO_BRIDGE.

Listen to these notifications in the vxlan driver. The FDB entries
learned this way have an NTF_EXT_LEARNED flag, and only entries marked
as such can be unlearned by the _DEL_ event. They are also immediately
marked as offloaded. This is the same behavior that the bridge driver
observes.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an external learning event collides with an user-added entry, the
user-added entry shouldn't be taken over. Otherwise on an unlearn event
the entry would be completely lost, even though the user added it by
hand.

Therefore skip update of FDB flags and state for these cases. This is in
accordance with the bridge behavior.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VXLAN driver needs to differentiate between FDB entries learned by
the VXLAN driver, and those added by the user. The latter ones shouldn't
be taken over by external learning events. This is in accordance with
bridge behavior.

Therefore, extend the flags bitfield to 16 bits and add a new private
NTF flag to mark the user-added entries.

This seems preferable to adding a dedicated boolean, because passing the
flag, unlike passing e.g. a true, makes it clear what the meaning of the
bit is.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a following patch, vxlan is extended to allow hardware FDB learning.
For FDB entries learned this way, switchdev notifications should not be
sent again, because the driver already knows about these entries.

To that end, add an argument vxlan_fdb_notify() to determine whether
the switchdev notifications should be sent. Propagate the argument to
all call sites transitively, eventually passing true in all root calls.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This argument is necessary for vxlan_fdb_delete(), the API of which is
prescribed by ndo_fdb_del, but __vxlan_fdb_delete() doesn't need it.
Therefore drop it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix comment typo rxfliterctrl -> rxfilterctrl
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michał Mirosław says:

====================
VLAN tag handling cleanup

This is a cleanup set after VLAN_TAG_PRESENT removal. The CFI bit
handling is made similar to how other tag fields are used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace open-coded bitfield manipulation with skb_vlan_tag_*() helpers.
This also enables correctly passing of VLAN.CFI bit.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Abstract CFI/DEI bit access consistently with other VLAN tag fields.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2018-11-20

This series contains updates to the ice driver only.

Akeem updates the driver to determine whether or not to do
auto-negotiation based on the VSI state.

Bruce cleans up the control queue code to remove duplicate code.  Take
advantage of some compiler optimizations by making some structures
constant, and also note that they cannot be modified.  Cleaned up
formatting issues and code comment that needed clarification.  Fixed a
potential NULL pointer dereference by adding a check.

Jaroslaw adds a check to verify if memory was allocated or not.

Yashaswini Raghuram fixes the driver to ensure we are not enabling the
LAN_EN flag if the MAC in the MAC-VLAN is a unicast MAC, so that the
unicast packets are not forwarded to the wire.

Dave fixes the return value of ice_napi_poll() to be more useful in
returning the work that was done and should only return 0 when no work
was done.

Anirudh does code comment cleanup, to make more consistent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'dsa-microchip-Modify-KSZ9477-DSA-driver-in-preparation-to-add-other-KSZ-switch-drivers'

Tristram Ha says:

====================
net: dsa: microchip: Modify KSZ9477 DSA driver in preparation to add other KSZ switch drivers

This series of patches is to modify the original KSZ9477 DSA driver so
that other KSZ switch drivers can be added and use the common code.

There are several steps to accomplish this achievement.  First is to
rename some function names with a prefix to indicate chip specific
function.  Second is to move common code into header that can be shared.
Last is to modify tag_ksz.c so that it can handle many tail tag formats
used by different KSZ switch drivers.

ksz_common.c will contain the common code used by all KSZ switch drivers.
ksz9477.c will contain KSZ9477 code from the original ksz_common.c.
ksz9477_spi.c is renamed from ksz_spi.c.
ksz9477_reg.h is renamed from ksz_9477_reg.h.
ksz_common.h is added to provide common code access to KSZ switch
drivers.
ksz_spi.h is added to provide common SPI access functions to KSZ SPI
drivers.

v4
- Patches were removed to concentrate on changing driver structure without
adding new code.

v3
- The phy_device structure is used to hold port link information
- A structure is passed in ksz_xmit and ksz_rcv instead of function pointer
- Switch offload forwarding is supported

v2
- Initialize reg_mutex before use
- The alu_mutex is only used inside chip specific functions

v1
- Each patch in the set is self-contained
- Use ksz9477 prefix to indicate KSZ9477 specific code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename ksz_9477_reg.h to ksz9477_reg.h for consistency as the product
name is always KSZ####.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Break KSZ9477 DSA driver into two files in preparation to add more KSZ
switch drivers.
Add common functions in ksz_common.h so that other KSZ switch drivers
can access code in ksz_common.c.
Add ksz_spi.h for common functions used by KSZ switch SPI drivers.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename ksz_spi.c to ksz9477_spi.c and update Kconfig in preparation to add
more KSZ switch drivers.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename some functions with ksz9477 prefix to separate chip specific code
from common code.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean up code according to patch check suggestions.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace license with GPL.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent update to smatch is causing it to report the error "we previously
assumed 'm_entry->vsi_list_info' could be null". Fix that.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In code comments, use Tx|Rx instead of tx|rx
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>