- 11 Dec, 2017 14 commits
-
-
Mauro Carvalho Chehab authored
The tuning logic is broken with regards to status report: it relies on a previously-cached value that may not be valid if re-tuned. Change the logic to always read the status. Acked-by:
Daniel Scheller <d.scheller@gmx.net> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Akinobu Mita authored
Fix typo s/:/;/ Cc: Rob Herring <robh+dt@kernel.org> Cc: Hyun Kwon <hyun.kwon@xilinx.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Maciej S. Szmigiero authored
If set_fmt callback is called with format->width or format->height set to zero and HACTIVE_CNT or VACTIVE_CNT bits (respectively) in chip are zero we will divide by zero later in this callback when we try to calculate HSC or VSC values. Fix this by explicitly rejecting these values. Signed-off-by:
Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by:
-
Maciej S. Szmigiero authored
A 0b1100 value in 4 LSBs of "General Status 1" register (AFD_FMT_STAT) has known meaning for CX2584x-series chips - it means that a SECAM signal is currently detected by the chip. Use this opportunity to also fix wrong binary values that were present as comments attached to some entries in an array where chip register -> V4L2 standard mappings are stored. Signed-off-by:
-
Russell King authored
Setting a burst size of "8" doesn't work for IMX219 with 8-bit bayer, but a burst size of "16" does. Fix this. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Acked-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Russell King authored
The complete handler walks all entities, expecting to find an imx subdevice for each and every entity. However, camera drivers such as smiapp can themselves contain multiple entities, for which there will not be an imx subdevice. This causes imx_media_find_subdev_by_sd() to fail, making the imx capture system unusable with such cameras. Work around this by killing the error entirely, thereby allowing the imx capture to be used with such cameras. Signed-off-by:
Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by:
-
Malcolm Priestley authored
When the tuner was split from m88rs2000 the attach function is in wrong place. Move to dm04_lme2510_tuner to trap errors on failure and removing a call to lme_coldreset. Prevents driver starting up without any tuner connected. Fixes to trap for ts2020 fail. LME2510(C): FE Found M88RS2000 ts2020: probe of 0-0060 failed with error -11 ... LME2510(C): TUN Found RS2000 tuner kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Tested-by:
-
Malcolm Priestley authored
Warm start has no check as whether a genuine device has connected and proceeds to next execution path. Check device should read 0x47 at offset of 2 on USB descriptor read and it is the amount requested of 6 bytes. Fix for kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access as Reported-by:
-
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, add the proper SPDX, better identifying the licenses whith apply to the source code. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2 at the Siano's common driver. Some codes there are licensed on GPL v2 or latter, while others are GPL v2 only. So, in order to reflect the common license that applies to everything, the module itself should be GPLv2 only. While here, use the Kernel's coding style for the comments with copyright info. Signed-off-by: -
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on the several media drivers I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on the several RC keymap files I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to identify GPL v2, as this is the minimal license requirement for those modles. Signed-off-by: -
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on several media drivers I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2. Signed-off-by:
Philippe Ombredanne <pombredanne@nexb.com> Acked-by:
-
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on the several media drivers I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2. Signed-off-by:
-
Mauro Carvalho Chehab authored
As we're now using SPDX identifiers, on the several media drivers I wrote, add the proper SPDX, identifying the license I meant. As we're now using the short license, it doesn't make sense to keep the original license text. Also, fix MODULE_LICENSE to properly identify GPL v2. Signed-off-by:
-
- 08 Dec, 2017 26 commits
-
-
Laurent Pinchart authored
According to the UVC specification, stream error events carry no data. Fix a buffer overflow (that should be harmless given data alignment) when reporting the stream error event by removing the data byte from the message. Signed-off-by:
-
Baoyou Xie authored
Some cameras post inaccurate frame where next frame data overlap it. this results in screen flicker, and it need to be prevented. So this patch marks the buffer error to discard the frame where buffer overflow. Signed-off-by:
Baoyou Xie <baoyou.xie@linaro.org> Reviewed-by:
-
Jaejoong Kim authored
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0] by & operation with 0x7ff. So, we can remove the duplicate & operation with 0x7ff. Signed-off-by:
Jaejoong Kim <climbbb.kim@gmail.com> Reviewed-by:
-
Nicolas Dufresne authored
Microsoft HoloLense UVC sensor uses D3DFMT instead of FOURCC when exposing formats. This adds support for D3DFMT_L8 as exposed from the Acer Windows Mixed Reality Headset. Signed-off-by:
Nicolas Dufresne <nicolas.dufresne@collabora.com> Reviewed-by:
-
Vasyl Gomonovych authored
Fix ptr_ret.cocci warnings: drivers/media/platform/exynos4-is/fimc-lite.c:1465:1-3: WARNING: PTR_ERR_OR_ZERO can be used Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR Generated by: scripts/coccinelle/api/ptr_ret.cocci Signed-off-by:
Vasyl Gomonovych <gomonovych@gmail.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Stanimir Varbanov authored
Move ptype (property type) initialization out of switch case and save few lines of code. Signed-off-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by:
-
Geert Uytterhoeven authored
As of_node_full_name() now returns only the basename, the endpoint information printed became useless: adv748x 4-0070: Endpoint endpoint on port 7 adv748x 4-0070: Endpoint endpoint on port 8 adv748x 4-0070: Endpoint endpoint on port 10 adv748x 4-0070: Endpoint endpoint on port 11 Restore the old behavior by using "%pOF" instead: adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@7/endpoint on port 7 adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@8/endpoint on port 8 adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@10/endpoint on port 10 adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@11/endpoint on port 11 Fixes: a7e4cfb0 ("of/fdt: only store the device node basename in full_name") Signed-off-by:Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Acked-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Arnd Bergmann authored
timespec is generally deprecated because of the y2038 overflow. In vivid, the usage is fine, since we are dealing with monotonic timestamps, but we can also simplify the code by going to ktime_t. Using ktime_divns() should be roughly as efficient as the old code, since the constant 64-bit division gets turned into a multiplication on modern platforms, and we save multiple 32-bit divisions that can be expensive e.g. on ARMv7. Tested-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Arnd Bergmann authored
The imx media driver passes around monotonic timestamps in the deprecated 'timespec' format. This is not a problem for the driver, as they won't overflow, but moving to either timespec64 or ktime_t is preferred. I'm picking ktime_t for simplicity here. frame_interval_monitor() is the main function that changes, as it tries to compare a time interval in microseconds. The algorithm slightly changes here, to avoid 64-bit division. The code previously assumed that the error was at most 32-bit worth of microseconds here, so I'm making the same assumption but add an explicit test for it. Signed-off-by:
-
Arnd Bergmann authored
solo6x10 correctly deals with time stamps and will never suffer from overflows, but it uses the deprecated 'struct timespec' type and 'ktime_get_ts()' interface to read the monotonic clock. This changes it to use ktime_get_ts64() instead, so we can eventually remove ktime_get_ts(). Signed-off-by:
Ismael Luceno <ismael@iodev.co.uk> Signed-off-by:
-
Loic Poulain authored
Deblocking filter allows to reduce blocking artifacts and improve visual quality. This is configurable via the V4L2 API but eventually not applied to the encoder. Note that alpha and beta deblocking values are 32-bit signed (-6;+6). Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Reviewed-by:
-
Loic Poulain authored
H264 entropy mode can be selected via V4L2 API but is eventually not applied. Configure encoder with selected mode, CALVC (def) or CABAC. Note that hw/firmware also expects a CABAC model configuration which currently doesn't have existing V4L2 API control. For now, use model_0 which seems always supported and so the default one. Signed-off-by:
-
Gustavo A. R. Silva authored
Check return value from call to devm_kzalloc() in order to prevent a NULL pointer dereference. This issue was detected with the help of Coccinelle. Fixes: 4a5f8ae5 ("[media] davinci: vpif_capture: get subdevs from DT when available") Signed-off-by:
Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by:
-
Jesse Chan authored
This change resolves a new compile-time warning when built as a loadable module: WARNING: modpost: missing MODULE_LICENSE() in drivers/media/platform/tegra-cec/tegra_cec.o see include/linux/module.h for more information This adds the license as "GPL v2", which matches the header of the file. MODULE_DESCRIPTION and MODULE_AUTHOR are also added. Signed-off-by:
Jesse Chan <jc@linux.com> Signed-off-by:
-
Jesse Chan authored
This change resolves a new compile-time warning when built as a loadable module: WARNING: modpost: missing MODULE_LICENSE() in drivers/media/platform/soc_camera/soc_scale_crop.o see include/linux/module.h for more information This adds the license as "GPL", which matches the header of the file. MODULE_DESCRIPTION and MODULE_AUTHOR are also added. Signed-off-by:
-
Jesse Chan authored
This change resolves a new compile-time warning when built as a loadable module: WARNING: modpost: missing MODULE_LICENSE() in drivers/media/platform/mtk-vcodec/mtk-vcodec-common.o see include/linux/module.h for more information This adds the license as "GPL v2", which matches the header of the file. MODULE_DESCRIPTION is also added. Signed-off-by:
-
Greg Kroah-Hartman authored
There is no need to #define the license of the driver, just put it in the MODULE_LICENSE() line directly as a text string. This allows tools that check that the module license matches the source code license to work properly, as there is no need to unwind the unneeded dereference. Cc: Hans Verkuil <hverkuil@xs4all.nl> Cc: Johan Hovold <johan@kernel.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Reported-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by:
Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by:
-
Arnd Bergmann authored
time_to_tm() takes a time_t value that overflows in 2038 on 32-bit systems. time64_to_tm() doesn't have this problem, so let's use that in combination with ktime_get_real_seconds() to read a 64-bit time value. Signed-off-by:
-
Dan Carpenter authored
The cam->buffers[] array has cam->num_frames elements so the > needs to be changed to >= to avoid going beyond the end of the array. The ->buffers[] array is allocated in cpia2_allocate_buffers() if you want to confirm. Fixes: ab33d507 ("V4L/DVB (3376): Add cpia2 camera support") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Martin Kepplinger authored
According to i.MX VPU API Reference Manuals the MJPG video codec is referenced to by number 7, not 3. Also Philipp pointed out that this value is only meant to fill in CMD_ENC_SEQ_COD_STD for encoding, only on i.MX53. It was never written to any register, and even if defined correctly, wouldn't be needed for i.MX6. So avoid confusion and remove this definition. Signed-off-by:
Martin Kepplinger <martink@posteo.de> Acked-by:
-
Gustavo A. R. Silva authored
Fix inconsistent IS_ERR and PTR_ERR in csi_link_validate. The proper pointer to be passed as argument is sensor. This issue was detected with the help of Coccinelle. Reported-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
-
Hans Verkuil authored
When the device is being unregistered disable the hardware, don't wait until cec_delete_adapter is called as the hardware may have disappeared by then. This would be the case for hotplugable devices. Signed-off-by:
Bård Eirik Winther <bwinther@cisco.com> Tested-by:
-
Hans Verkuil authored
Document what this op does. Signed-off-by:
-
Hans Verkuil authored
Some devices can monitor the CEC pin using an interrupt, but you only want to enable the interrupt if you actually switch to pin monitoring mode. So add a new op that is called when pin monitoring needs to be switched on or off. Also fix a small bug where the initial CEC pin event was sent again when calling S_MODE twice with the same CEC_MODE_MONITOR_PIN mode. Signed-off-by:
-
Arnd Bergmann authored
The firmware timestamp is an unsigned 32-bit value, but we copy it into a signed 32-bit variable, so we can theoretically get an overflow in the calculation when the timestamp is between 2038 and 2106. This changes the temporary variable to time64_t and changes the deprecated time_to_tm() over to time64_to_tm() accordingly. There is still an overflow in y2106, but that is a limitation of the firmware interface, not a kernel problem. Signed-off-by:
-
Hans Verkuil authored
Add support for the test_pattern control and the h/vflip controls. This makes it possible to switch to more interesting test patterns and to test control handling in v4l-subdevs. There are more tpg-related controls that can be added, but this is a good start. Signed-off-by:
-
