[ Upstream commit 427460c8 ]

When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.

The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.

Testing performed on Altera CycloneV (D_CAN).  Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 8c5122e4 ]

When this code was reworked for IBoE support the order of assignments
for the sl_tclass_flowlabel got flipped around resulting in
TClass & FlowLabel being permanently set to 0 in the packet headers.

This breaks IB routers that rely on these headers, but only affects
kernel users - libmlx4 does this properly for user space.

Cc: stable@vger.kernel.org
Fixes: fa417f7b ("IB/mlx4: Add support for IBoE")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 64c12921 ]

The test for !trans->blocks_used in btrfs_abort_transaction is
insufficient to determine whether it's safe to drop the transaction
handle on the floor.  btrfs_cow_block, informed by should_cow_block,
can return blocks that have already been CoW'd in the current
transaction.  trans->blocks_used is only incremented for new block
allocations. If an operation overlaps the blocks in the current
transaction entirely and must abort the transaction, we'll happily
let it clean up the trans handle even though it may have modified
the blocks and will commit an incomplete operation.

In the long-term, I'd like to do closer tracking of when the fs
is actually modified so we can still recover as gracefully as possible,
but that approach will need some discussion.  In the short term,
since this is the only code using trans->blocks_used, let's just
switch it to a bool indicating whether any blocks were used and set
it when should_cow_block returns false.

Cc: stable@vger.kernel.org # 3.4+
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 8198868f ]

Call path:

  1) snd_hdac_power_up_pm()
  2) snd_hdac_power_up()
  3) pm_runtime_get_sync()
  4) __pm_runtime_resume()
  5) rpm_resume()

The rpm_resume() returns 1 when the device is already active.
Because the return value is unmodified, the hdac regmap read/write
functions should allow this value for the retry I/O operation, too.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 3194ed49 ]

HD-audio driver uses regmap cache bypass feature for reading a raw
value without the cache.  But this is racy since both the cached and
the uncached reads may occur concurrently.  The former is done via the
normal control API access while the latter comes from the proc file
read.

Even though the regmap itself has the protection against the
concurrent accesses, the flag set/reset is done without the
protection, so it may lead to inconsistent state of bypass flag that
doesn't match with the current read and occasionally result in a
kernel WARNING like:
  WARNING: CPU: 3 PID: 2731 at drivers/base/regmap/regcache.c:499 regcache_cache_only+0x78/0x93

One way to work around such a problem is to wrap with a mutex.  But in
this case, the solution is simpler: for the uncached read, we just
skip the regmap and directly calls its accessor.  The verb execution
there is protected by itself, so basically it's safe to call
individually.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 38327424 ]

If __key_link_begin() failed then "edit" would be uninitialized.  I've
added a check to fix that.

This allows a random user to crash the kernel, though it's quite
difficult to achieve.  There are three ways it can be done as the user
would have to cause an error to occur in __key_link():

 (1) Cause the kernel to run out of memory.  In practice, this is difficult
     to achieve without ENOMEM cropping up elsewhere and aborting the
     attempt.

 (2) Revoke the destination keyring between the keyring ID being looked up
     and it being tested for revocation.  In practice, this is difficult to
     time correctly because the KEYCTL_REJECT function can only be used
     from the request-key upcall process.  Further, users can only make use
     of what's in /sbin/request-key.conf, though this does including a
     rejection debugging test - which means that the destination keyring
     has to be the caller's session keyring in practice.

 (3) Have just enough key quota available to create a key, a new session
     keyring for the upcall and a link in the session keyring, but not then
     sufficient quota to create a link in the nominated destination keyring
     so that it fails with EDQUOT.

The bug can be triggered using option (3) above using something like the
following:

	echo 80 >/proc/sys/kernel/keys/root_maxbytes
	keyctl request2 user debug:fred negate @t

The above sets the quota to something much lower (80) to make the bug
easier to trigger, but this is dependent on the system.  Note also that
the name of the keyring created contains a random number that may be
between 1 and 10 characters in size, so may throw the test off by
changing the amount of quota used.

Assuming the failure occurs, something like the following will be seen:

	kfree_debugcheck: out of range ptr 6b6b6b6b6b6b6b68h
	------------[ cut here ]------------
	kernel BUG at ../mm/slab.c:2821!
	...
	RIP: 0010:[<ffffffff811600f9>] kfree_debugcheck+0x20/0x25
	RSP: 0018:ffff8804014a7de8  EFLAGS: 00010092
	RAX: 0000000000000034 RBX: 6b6b6b6b6b6b6b68 RCX: 0000000000000000
	RDX: 0000000000040001 RSI: 00000000000000f6 RDI: 0000000000000300
	RBP: ffff8804014a7df0 R08: 0000000000000001 R09: 0000000000000000
	R10: ffff8804014a7e68 R11: 0000000000000054 R12: 0000000000000202
	R13: ffffffff81318a66 R14: 0000000000000000 R15: 0000000000000001
	...
	Call Trace:
	  kfree+0xde/0x1bc
	  assoc_array_cancel_edit+0x1f/0x36
	  __key_link_end+0x55/0x63
	  key_reject_and_link+0x124/0x155
	  keyctl_reject_key+0xb6/0xe0
	  keyctl_negate_key+0x10/0x12
	  SyS_keyctl+0x9f/0xe7
	  do_syscall_64+0x63/0x13a
	  entry_SYSCALL64_slow_path+0x25/0x25

Fixes: f70e2e06 ('KEYS: Do preallocation for __key_link()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 8fa3b8d6 ]

If percpu_ref initialization fails during css_create(), the free path
can end up trying to free css->id of zero.  As ID 0 is unused, it
doesn't cause a critical breakage but it does trigger a warning
message.  Fix it by setting css->id to -1 from init_and_link_css().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Wenwei Tao <ww.tao0320@gmail.com>
Fixes: 01e58659 ("cgroup: release css->id after css_free")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 8f50b8e5 ]

In the omap gpmc driver it can be noticed that GPMC_CONFIG4_OEEXTRADELAY
is overwritten by the WEEXTRADELAY value from the device tree and
GPMC_CONFIG4_WEEXTRADELAY is not updated by the value from the device
tree.

As a consequence, the memory accesses cannot be configured properly when
the extra delay are needed for OE and WE.

Fix the update of GPMC_CONFIG4_WEEXTRADELAY with the value from the
device tree file and prevents GPMC_CONFIG4_OEXTRADELAY
being overwritten by the WEXTRADELAY value from the device tree.

Cc: stable@vger.kernel.org
Signed-off-by: Ocquidant, Sebastien <sebastienocquidant@eaton.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit caf1ff26 ]

These days, we experienced one guest crash with 8 cores and 3 disks,
with qemu error logs as bellow:

qemu-system-x86_64: /build/qemu-2.0.0/kvm-all.c:984:
kvm_irqchip_commit_routes: Assertion `ret == 0' failed.

And then we found one patch(bdf026317d) in qemu tree, which said
could fix this bug.

Execute the following script will reproduce the BUG quickly:

irq_affinity.sh
========================================================================

vda_irq_num=25
vdb_irq_num=27
while [ 1 ]
do
    for irq in {1,2,4,8,10,20,40,80}
        do
            echo $irq > /proc/irq/$vda_irq_num/smp_affinity
            echo $irq > /proc/irq/$vdb_irq_num/smp_affinity
            dd if=/dev/vda of=/dev/zero bs=4K count=100 iflag=direct
            dd if=/dev/vdb of=/dev/zero bs=4K count=100 iflag=direct
        done
done
========================================================================

The following qemu log is added in the qemu code and is displayed when
this bug reproduced:

kvm_irqchip_commit_routes: max gsi: 1008, nr_allocated_irq_routes: 1024,
irq_routes->nr: 1024, gsi_count: 1024.

That's to say when irq_routes->nr == 1024, there are 1024 routing entries,
but in the kernel code when routes->nr >= 1024, will just return -EINVAL;

The nr is the number of the routing entries which is in of
[1 ~ KVM_MAX_IRQ_ROUTES], not the index in [0 ~ KVM_MAX_IRQ_ROUTES - 1].

This patch fix the BUG above.

Cc: stable@vger.kernel.org
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: Zhang Zhuoyu <zhangzhuoyu@cmss.chinamobile.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 7e1b1fc4 ]

Modules which register drivers via standard path (driver_register) in
parallel can cause a warning:
WARNING: CPU: 2 PID: 3492 at ../fs/sysfs/dir.c:31 sysfs_warn_dup+0x62/0x80
sysfs: cannot create duplicate filename '/module/saa7146/drivers'
Modules linked in: hexium_gemini(+) mxb(+) ...
...
Call Trace:
...
 [<ffffffff812e63a2>] sysfs_warn_dup+0x62/0x80
 [<ffffffff812e6487>] sysfs_create_dir_ns+0x77/0x90
 [<ffffffff8140f2c4>] kobject_add_internal+0xb4/0x340
 [<ffffffff8140f5b8>] kobject_add+0x68/0xb0
 [<ffffffff8140f631>] kobject_create_and_add+0x31/0x70
 [<ffffffff8157a703>] module_add_driver+0xc3/0xd0
 [<ffffffff8155e5d4>] bus_add_driver+0x154/0x280
 [<ffffffff815604c0>] driver_register+0x60/0xe0
 [<ffffffff8145bed0>] __pci_register_driver+0x60/0x70
 [<ffffffffa0273e14>] saa7146_register_extension+0x64/0x90 [saa7146]
 [<ffffffffa0033011>] hexium_init_module+0x11/0x1000 [hexium_gemini]
...

As can be (mostly) seen, driver_register causes this call sequence:
  -> bus_add_driver
    -> module_add_driver
      -> module_create_drivers_dir
The last one creates "drivers" directory in /sys/module/<...>. When
this is done in parallel, the directory is attempted to be created
twice at the same time.

This can be easily reproduced by loading mxb and hexium_gemini in
parallel:
while :; do
  modprobe mxb &
  modprobe hexium_gemini
  wait
  rmmod mxb hexium_gemini saa7146_vv saa7146
done

saa7146 calls pci_register_driver for both mxb and hexium_gemini,
which means /sys/module/saa7146/drivers is to be created for both of
them.

Fix this by a new mutex in module_create_drivers_dir which makes the
test-and-create "drivers" dir atomic.

I inverted the condition and removed 'return' to avoid multiple
unlocks or a goto.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: fe480a26 (Modules: only add drivers/ direcory if needed)
Cc: v2.6.21+ <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d50039ea ]

Also simplify the logic a bit.

Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: Trond Myklebust <trondmy@primarydata.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit fd2d2bac ]

Not clearing mst manager's proposed vcpis table for destroyed connectors when the manager is stopped leaves it pointing to unrefernced memory, this causes pagefault when the manager is restarted when plugging back a branch.

Fixes: 91a25e46 ("drm/dp/mst: deallocate payload on port destruction")
Signed-off-by: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Cc: stable@vger.kernel.org
Cc: Mykola Lysenko <Mykola.Lysenko@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 476490a9 ]

Thanks to Ville Syrjälä for pointing me towards the cause of this issue.

Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:

[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config]     FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config]     scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A

Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.

A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.

Changes since v4:
 - Fix calculation of final for systems with LVDS panels (fixes BUG() on
   CI test suite)
Changes since v3:
 - Move temp variable into loop
 - Move checks for using_ssc_source to after we've figured out has_ck505
 - Add using_ssc_source to debug output
Changes since v2:
 - Fix debug output for when we disable the CPU source
Changes since v1:
 - Leave the SSC source clock on instead of just shutting it off on all
   of the DPLL configurations.

Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465916649-10228-1-git-send-email-cpaul@redhat.comSigned-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 5bc28b93 ]

Change power_supply_read_temp() to use power_supply_get_property()
so that it will check the use_cnt and ensure it is > 0. The use_cnt
will be incremented at the end of __power_supply_register, so this
will block to case where get_property can be called before the supply
is fully registered. This fixes the issue show in the stack below:

[    1.452598] power_supply_read_temp+0x78/0x80
[    1.458680] thermal_zone_get_temp+0x5c/0x11c
[    1.464765] thermal_zone_device_update+0x34/0xb4
[    1.471195] thermal_zone_device_register+0x87c/0x8cc
[    1.477974] __power_supply_register+0x364/0x424
[    1.484317] power_supply_register_no_ws+0x10/0x18
[    1.490833] bq27xxx_battery_setup+0x10c/0x164
[    1.497003] bq27xxx_battery_i2c_probe+0xd0/0x1b0
[    1.503435] i2c_device_probe+0x174/0x240
[    1.509172] driver_probe_device+0x1fc/0x29c
[    1.515167] __driver_attach+0xa4/0xa8
[    1.520643] bus_for_each_dev+0x58/0x98
[    1.526204] driver_attach+0x20/0x28
[    1.531505] bus_add_driver+0x1c8/0x22c
[    1.537067] driver_register+0x68/0x108
[    1.542630] i2c_register_driver+0x38/0x7c
[    1.548457] bq27xxx_battery_i2c_driver_init+0x18/0x20
[    1.555321] do_one_initcall+0x38/0x12c
[    1.560886] kernel_init_freeable+0x148/0x1ec
[    1.566972] kernel_init+0x10/0xfc
[    1.572101] ret_from_fork+0x10/0x40

Also make the same change to ps_get_max_charge_cntl_limit() and
ps_get_cur_chrage_cntl_limit() to be safe. Lastly, change the return
value of power_supply_get_property() to -EAGAIN from -ENODEV if
use_cnt <= 0.

Fixes: 297d716f ("power_supply: Change ownership from driver to core")
Cc: stable@vger.kernel.org
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 57675cb9 ]

Lengthy output of sysrq-w may take a lot of time on slow serial console.

Currently we reset NMI-watchdog on the current CPU to avoid spurious
lockup messages. Sometimes this doesn't work since softlockup watchdog
might trigger on another CPU which is waiting for an IPI to proceed.
We reset softlockup watchdogs on all CPUs, but we do this only after
listing all tasks, and this may be too late on a busy system.

So, reset watchdogs CPUs earlier, in for_each_process_thread() loop.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1465474805-14641-1-git-send-email-aryabinin@virtuozzo.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit dcfc4724 ]

Fix kprobe_fault_handler() to clear the TF (trap flag) bit of
the flags register in the case of a fault fixup on single-stepping.

If we put a kprobe on the instruction which caused a
page fault (e.g. actual mov instructions in copy_user_*),
that fault happens on the single-stepping buffer. In this
case, kprobes resets running instance so that the CPU can
retry execution on the original ip address.

However, current code forgets to reset the TF bit. Since this
fault happens with TF bit set for enabling single-stepping,
when it retries, it causes a debug exception and kprobes
can not handle it because it already reset itself.

On the most of x86-64 platform, it can be easily reproduced
by using kprobe tracer. E.g.

  # cd /sys/kernel/debug/tracing
  # echo p copy_user_enhanced_fast_string+5 > kprobe_events
  # echo 1 > events/kprobes/enable

And you'll see a kernel panic on do_debug(), since the debug
trap is not handled by kprobes.

To fix this problem, we just need to clear the TF bit when
resetting running kprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: systemtap@sourceware.org
Cc: stable@vger.kernel.org # All the way back to ancient kernels
Link: http://lkml.kernel.org/r/20160611140648.25885.37482.stgit@devbox
[ Updated the comments. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 719bd654 ]

The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 6d9fe44b ]

When testing SPI without DMA I noticed that filling the FIFO on the
spi controller causes timeout.

Always leave room for one byte in the FIFO.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 797179bc ]

Copy __kvm_mips_vcpu_run() into unmapped memory, so that we can never
get a TLB refill exception in it when KVM is built as a module.

This was observed to happen with the host MIPS kernel running under
QEMU, due to a not entirely transparent optimisation in the QEMU TLB
handling where TLB entries replaced with TLBWR are copied to a separate
part of the TLB array. Code in those pages continue to be executable,
but those mappings persist only until the next ASID switch, even if they
are marked global.

An ASID switch happens in __kvm_mips_vcpu_run() at exception level after
switching to the guest exception base. Subsequent TLB mapped kernel
instructions just prior to switching to the guest trigger a TLB refill
exception, which enters the guest exception handlers without updating
EPC. This appears as a guest triggered TLB refill on a host kernel
mapped (host KSeg2) address, which is not handled correctly as user
(guest) mode accesses to kernel (host) segments always generate address
error exceptions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit ea1d39a3 ]

Fix warning about tainted kernel because usb-otg-fsm has no license.
WARNING: with this patch usb-otg-fsm module can be loaded
but then the kernel will hang. Tested with a udoo quad board.

Cc: <stable@vger.kernel.org> #v4.1+
Signed-off-by: Oscar <oscar@naiandei.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 05082b8b ]

When executing in a PCI passthrough based virtuzliation environment, the
hypervisor will usually attempt to send a PCIe bus reset signal to the
ASIC when the VM reboots. In this scenario, the card is not correctly
initialized, but we still consider it to be posted. Therefore, in a
passthrough based environemnt we should always post the card to guarantee
it is in a good state for driver initialization.

Ported from amdgpu commit:
amdgpu: fix asic initialization for virtualized environments

Cc: Andres Rodriguez <andres.rodriguez@amd.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit ae4ea9a2 ]

Commit 7ea0ed2b ("ipmi: Make the message handler easier to use for
SMI interfaces") changed handle_new_recv_msgs() to call handle_one_recv_msg()
for a smi_msg while the smi_msg is still connected to waiting_rcv_msgs list.
That could lead to following list corruption problems:

1) low-level function treats smi_msg as not connected to list

  handle_one_recv_msg() could end up calling smi_send(), which
  assumes the msg is not connected to list.

  For example, the following sequence could corrupt list by
  doing list_add_tail() for the entry still connected to other list.

    handle_new_recv_msgs()
      msg = list_entry(waiting_rcv_msgs)
      handle_one_recv_msg(msg)
        handle_ipmb_get_msg_cmd(msg)
          smi_send(msg)
            spin_lock(xmit_msgs_lock)
            list_add_tail(msg)
            spin_unlock(xmit_msgs_lock)

2) race between multiple handle_new_recv_msgs() instances

  handle_new_recv_msgs() once releases waiting_rcv_msgs_lock before calling
  handle_one_recv_msg() then retakes the lock and list_del() it.

  If others call handle_new_recv_msgs() during the window shown below
  list_del() will be done twice for the same smi_msg.

  handle_new_recv_msgs()
    spin_lock(waiting_rcv_msgs_lock)
    msg = list_entry(waiting_rcv_msgs)
    spin_unlock(waiting_rcv_msgs_lock)
  |
  | handle_one_recv_msg(msg)
  |
    spin_lock(waiting_rcv_msgs_lock)
    list_del(msg)
    spin_unlock(waiting_rcv_msgs_lock)

Fixes: 7ea0ed2b ("ipmi: Make the message handler easier to use for SMI interfaces")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
[Added a comment to describe why this works.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 3.19
Tested-by: Ye Feng <yefeng.yl@alibaba-inc.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 19ced623 ]

The hash buffer is really HASH_BLOCK_SIZE bytes, someone
must have thought that memmove takes n*u32 words by mistake.
Tests work as good/bad as before after this patch.

Cc: Joakim Bech <joakim.bech@linaro.org>
Cc: stable@vger.kernel.org
Reported-by: David Binderman <linuxdev.baldrick@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 12d3f49e ]

All of the VMX AES ciphers (AES, AES-CBC and AES-CTR) are set at
priority 1000. Unfortunately this means we never use AES-CBC and
AES-CTR, because the base AES-CBC cipher that is implemented on
top of AES inherits its priority.

To fix this, AES-CBC and AES-CTR have to be a higher priority. Set
them to 2000.

Testing on a POWER8 with:

cryptsetup benchmark --cipher aes --key-size 256

Shows decryption speed increase from 402.4 MB/s to 3069.2 MB/s,
over 7x faster. Thanks to Mike Strosaker for helping me debug
this issue.

Fixes: 8c755ace ("crypto: vmx - Adding CBC routines for VMX module")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 56530f5d ]

Currently pmd_mknotpresent will use a zero entry to respresent an
invalidated pmd.

Unfortunately this definition clashes with pmd_none, thus it is
possible for a race condition to occur if zap_pmd_range sees pmd_none
whilst __split_huge_pmd_locked is running too with pmdp_invalidate
just called.

This patch fixes the race condition by modifying pmd_mknotpresent to
create non-zero faulting entries (as is done in other architectures),
removing the ambiguity with pmd_none.

[catalin.marinas@arm.com: using L_PMD_SECT_VALID instead of PMD_TYPE_SECT]

Fixes: 8d962507 ("ARM: mm: Transparent huge page support for LPAE systems.")
Cc: <stable@vger.kernel.org> # 3.11+
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 62453188 ]

In a subsequent patch, pmd_mknotpresent will clear the valid bit of the
pmd entry, resulting in a not-present entry from the hardware's
perspective. Unfortunately, pmd_present simply checks for a non-zero pmd
value and will therefore continue to return true even after a
pmd_mknotpresent operation. Since pmd_mknotpresent is only used for
managing huge entries, this is only an issue for the 3-level case.

This patch fixes the 3-level pmd_present implementation to take into
account the valid bit. For bisectability, the change is made before the
fix to pmd_mknotpresent.

[catalin.marinas@arm.com: comment update regarding pmd_mknotpresent patch]

Fixes: 8d962507 ("ARM: mm: Transparent huge page support for LPAE systems.")
Cc: <stable@vger.kernel.org> # 3.11+
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steve Capper <Steve.Capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 72d8c36e ]

sas_ata_strategy_handler() adds the works of the ata error handler to
system_unbound_wq. This workqueue asynchronously runs work items, so the
ata error handler will be performed concurrently on different CPUs. In
this case, ->host_failed will be decreased simultaneously in
scsi_eh_finish_cmd() on different CPUs, and become abnormal.

It will lead to permanently inequality between ->host_failed and
->host_busy, and scsi error handler thread won't start running. IO
errors after that won't be handled.

Since all scmds must have been handled in the strategy handler, just
remove the decrement in scsi_eh_finish_cmd() and zero ->host_busy after
the strategy handler to fix this race.

Fixes: 50824d6c ("[SCSI] libsas: async ata-eh")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit f8a15a96 ]

There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.

Commit a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.

This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.

Fixes: a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 7b2c17f8 ]

Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit f3eec0cf ]

shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d95815ba ]

I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.

Tests on another motherboard show that it does work with streams disabled.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 32cb0b37 ]

The Acer C120 LED Projector is a USB-3 connected pico projector which
takes both its power and video data from USB-3.

In combination with some hubs this device does not play well with
lpm, so disable lpm for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 81099f97 ]

Properly sort all the entries by vendor id.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit de95c40d ]

On some platforms, the clocks might be registered by a platform
driver. When this is the case, the clock platform driver may very well
be probed after xhci-plat, in which case the first probe() invocation
of xhci-plat will receive -EPROBE_DEFER as the return value of
devm_clk_get().

The current code handles that as a normal error, and simply assumes
that this means that the system doesn't have a clock for the XHCI
controller, and continues probing without calling
clk_prepare_enable(). Unfortunately, this doesn't work on systems
where the XHCI controller does have a clock, but that clock is
provided by another platform driver. In order to fix this situation,
we handle the -EPROBE_DEFER error condition specially, and abort the
XHCI controller probe(). It will be retried later automatically, the
clock will be available, devm_clk_get() will succeed, and the probe()
will continue with the clock prepared and enabled as expected.

In practice, such issue is seen on the ARM64 Marvell 7K/8K platform,
where the clocks are registered by a platform driver.

Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 3425aa03 ]

If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.

If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.

There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.

The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.

Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.

Cc: stable <stable@vger.kernel.org>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit ed596a4a ]

Flushing a work that reschedules itself is not a sensible operation. It needs
to be killed. Failure to do so leads to a kernel panic in the timer code.

CC: stable@vger.kernel.org
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d246dcb2 ]

[   40.467381] =============================================
[   40.473013] [ INFO: possible recursive locking detected ]
[   40.478651] 4.6.0-08691-g7f3db9a #37 Not tainted
[   40.483466] ---------------------------------------------
[   40.489098] usb/733 is trying to acquire lock:
[   40.493734]  (&(&dev->lock)->rlock){-.....}, at: [<bf129288>] ep0_complete+0x18/0xdc [gadgetfs]
[   40.502882]
[   40.502882] but task is already holding lock:
[   40.508967]  (&(&dev->lock)->rlock){-.....}, at: [<bf12a420>] ep0_read+0x20/0x5e0 [gadgetfs]
[   40.517811]
[   40.517811] other info that might help us debug this:
[   40.524623]  Possible unsafe locking scenario:
[   40.524623]
[   40.530798]        CPU0
[   40.533346]        ----
[   40.535894]   lock(&(&dev->lock)->rlock);
[   40.540088]   lock(&(&dev->lock)->rlock);
[   40.544284]
[   40.544284]  *** DEADLOCK ***
[   40.544284]
[   40.550461]  May be due to missing lock nesting notation
[   40.550461]
[   40.557544] 2 locks held by usb/733:
[   40.561271]  #0:  (&f->f_pos_lock){+.+.+.}, at: [<c02a6114>] __fdget_pos+0x40/0x48
[   40.569219]  #1:  (&(&dev->lock)->rlock){-.....}, at: [<bf12a420>] ep0_read+0x20/0x5e0 [gadgetfs]
[   40.578523]
[   40.578523] stack backtrace:
[   40.583075] CPU: 0 PID: 733 Comm: usb Not tainted 4.6.0-08691-g7f3db9a #37
[   40.590246] Hardware name: Generic AM33XX (Flattened Device Tree)
[   40.596625] [<c010ffbc>] (unwind_backtrace) from [<c010c1bc>] (show_stack+0x10/0x14)
[   40.604718] [<c010c1bc>] (show_stack) from [<c04207fc>] (dump_stack+0xb0/0xe4)
[   40.612267] [<c04207fc>] (dump_stack) from [<c01886ec>] (__lock_acquire+0xf68/0x1994)
[   40.620440] [<c01886ec>] (__lock_acquire) from [<c0189528>] (lock_acquire+0xd8/0x238)
[   40.628621] [<c0189528>] (lock_acquire) from [<c06ad6b4>] (_raw_spin_lock_irqsave+0x38/0x4c)
[   40.637440] [<c06ad6b4>] (_raw_spin_lock_irqsave) from [<bf129288>] (ep0_complete+0x18/0xdc [gadgetfs])
[   40.647339] [<bf129288>] (ep0_complete [gadgetfs]) from [<bf10a728>] (musb_g_giveback+0x118/0x1b0 [musb_hdrc])
[   40.657842] [<bf10a728>] (musb_g_giveback [musb_hdrc]) from [<bf108768>] (musb_g_ep0_queue+0x16c/0x188 [musb_hdrc])
[   40.668772] [<bf108768>] (musb_g_ep0_queue [musb_hdrc]) from [<bf12a944>] (ep0_read+0x544/0x5e0 [gadgetfs])
[   40.678963] [<bf12a944>] (ep0_read [gadgetfs]) from [<c0284470>] (__vfs_read+0x20/0x110)
[   40.687414] [<c0284470>] (__vfs_read) from [<c0285324>] (vfs_read+0x88/0x114)
[   40.694864] [<c0285324>] (vfs_read) from [<c0286150>] (SyS_read+0x44/0x9c)
[   40.702051] [<c0286150>] (SyS_read) from [<c0107820>] (ret_fast_syscall+0x0/0x1c)

This is caused by the spinlock bug in ep0_read().
Fix the two other deadlock sources in gadgetfs_setup() too.

Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 4879efb3 ]

dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.

Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.

Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057 ("usb: dwc3: exynos: add nop transceiver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 595144c1 ]

The flags element of clk_init_data was never initialized for mmc-
phase-clocks resulting in the element containing a random value
and thus possibly enabling unwanted clock flags.

Fixes: 89bf26cb ("clk: rockchip: Add support for the mmc clock phases using the framework")
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 9295c41d ]

Due to the way CUBC register is updated, a double flush is needed to
compute an accurate residue. First flush aim is to get data from the DMA
FIFO and second one ensures that we won't report data which are not in
memory.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9ee ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #v4.1 and later
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>