This patch completely changes the descriptor layout to improve
the whole performances due to the single read usage of the
descriptors in critical paths.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch restructures the DMA bus settings and this is done
by introducing a new platform structure used for programming
the AXI Bus Mode Register inside the DMA module.
This structure can be populated from device-tree as documented in the
binding txt file.

After initializing the DMA, the AXI register can be optionally tuned
for platform drivers based.
This patch also reworks some parameters to make coherent the DMA
configuration now that AXI register is introduced.
For example, the burst_len is managed by using the mentioned axi
support above; so the snps,burst-len parameter has been removed.
It makes sense to provide the AAL parameter from DT to Address-Aligned
Beats inside the Register0 and review the PBL settings when initialize
the engine.

For PCI glue, rebuilding the story of this setting, it
was added to align a configuration so not for fixing some
known problem. No issue raised after this patch.
It is safe to use the default burst length instead of
tuning it to the maximum value
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to share the same reset procedure between dwmac100 and
dwmac1000 chips.
This will also help on enhancing the driver and support new chips.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Santosh Shilimkar says:

====================
RDS: Major clean-up with couple of new features for 4.6

v3:
Re-generated the same series by omitting "-D" option from git format-patch
command. Since first patch has file removals, git apply/am can't deal
with it when formated with '-D' option.

v2:
Dropped module parameter from [PATCH 11/13] as suggested by David Miller

Series is generated against net-next but also applies against Linus's tip
cleanly. Entire patchset is available at below git tree:

 git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux.git for_4.6/net-next/rds_v2

The diff-stat looks bit scary since almost ~4K lines of code is
getting removed. Brief summary of the series:

- Drop the stale iWARP support:
	RDS iWarp support code has become stale and non testable for
	sometime.  As discussed and agreed earlier on list, am dropping
	its support for good. If new iWarp user(s) shows up in future,
	the plan is to adapt existing IB RDMA with special sink case.
- RDS gets SO_TIMESTAMP support
- Long due RDS maintainer entry gets updated
- Some RDS IB code refactoring towards new FastReg Memory registration (FRMR)
- Lastly the initial support for FRMR

RDS IB RDMA performance with FRMR is not yet as good as FMR and I do have
some patches in progress to address that. But they are not ready for 4.6
so I left them out of this series.

Also am keeping eye on new CQ API adaptations like other ULPs doing and
will try to adapt RDS for the same most likely in 4.7+ timeframe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fastreg MR(FRMR) is another method with which one can
register memory to HCA. Some of the newer HCAs supports only fastreg
mr mode, so we need to add support for it to have RDS functional
on them.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Avinash Repaka <avinash.repaka@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fastreg MR(FRMR) memory registration and invalidation makes use
of work request and completion queues for its operation. Patch
allocates extra queue space towards these operation(s).
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Discovere Fast Memmory Registration support using IB device
IB_DEVICE_MEM_MGT_EXTENSIONS. Certain HCA might support just FRMR
or FMR or both FMR and FRWR. In case both mr type are supported,
default FMR is used.

Default MR is still kept as FMR against what everyone else
is following. Default will be changed to FRMR once the
RDS performance with FRMR is comparable with FMR. The
work is in progress for the same.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add MR reuse statistics to RDS IB transport.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drop the RDS connection on RDMA_CM_EVENT_TIMEWAIT_EXIT so that
it can reconnect and resume.

While testing fastreg, this error happened in couple of tests but
was getting un-noticed.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Preperatory patch for FRMR support. From connection info,
we can retrieve cm_id which contains qp handled needed for
work request posting.

We also need to drop the RDS connection on QP error states
where connection handle becomes useful.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No functional change.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Keep fmr related filed in its own struct. Fastreg MR structure
will be added to the union.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No functional changes. This is in preperation towards adding
fastreg memory resgitration support.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This helps to combine asynchronous fastreg MR completion handler
with send completion handler.

No functional change.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Acked-by: Chien Yen <chien.yen@oracle.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SO_TIMESTAMP generates time stamp for each incoming RDS messages
User app can enable it by using SO_TIMESTAMP setsocketopt() at
SOL_SOCKET level. CMSG data of cmsg type SO_TIMESTAMP contains the
time stamp in struct timeval format.
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDS iWarp support code has become stale and non testable. As
indicated earlier, am dropping the support for it.

If new iWarp user(s) shows up in future, we can adapat the RDS IB
transprt for the special RDMA READ sink case. iWarp needs an MR
for the RDMA READ sink.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: update series

This patch series tries to improve general configuration by changing
configuration to better suit B0 boards and allow more available
resources to each physical function.
In additition, it contains some small fixes and semantic changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove 2 unused fields from driver code.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of problems when initializing the chip, the error flows aren't
being properly done. Specifically, it's possible that the chip would be
left in a configuration allowing it [internally] to access the host
memory, causing fatal problems in the device that would require power
cycle to overcome.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current statistics logic is meant for L2, not for all future protocols.
Move this content to the proper designated file.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BB_A0 is a development model that is will not reach actual clients.
In fact, future firmware would simply fail to initialize such chip.

This changes the configuration into B0 instead of A0, and adds a safeguard
against the slim chance someone would actually try this with an A0 adapter
in which case probe would gracefully fail.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver learns the inner bar sized from a register configured by management
firmware, but older versions are not setting this register.
But since we know which values were configured back then, use them instead.
Signed-off-by: Ram Amrani <Ram.Amrani@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver calls cfg80211_get_station, which may be part of a
module, so we must not enable BATMAN_ADV_BATMAN_V if
BATMAN_ADV=y and CFG80211=m:

net/built-in.o: In function `batadv_v_elp_get_throughput':
(text+0x5c62c): undefined reference to `cfg80211_get_station'

This clarifies the dependency to cover all combinations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c833484e ("batman-adv: ELP - compute the metric based on the estimated throughput")
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use managed resource functions devm_kzalloc and pcim_enable_device
to simplify error handling. Subsequently, remove unnecessary
kfree, pci_disable_device and pci_release_regions.

To be compatible with the change, various gotos are replaced with
direct returns and unneeded labels are dropped.

Also, `sc` was only being freed in the probe function and not the
remove function before the change. By using devm_kzalloc this patch
also fixes this memory leak.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
batman-adv 20160229

this is our (hopefully) latest batch of patches intended for net-next.

With this patchset we finally introduce B.A.T.M.A.N. V: the latest
version of our routing protocol.
Technical documentation describing the protocol in more detail can
be found in our wiki[1][2][3][4].

For what concerns this pull request, you can find the high level
description right below.

[1] https://www.open-mesh.org/projects/batman-adv/wiki/BATMAN_V
[2] https://www.open-mesh.org/projects/batman-adv/wiki/OGMv2
[3] https://www.open-mesh.org/projects/batman-adv/wiki/ELP
[4] https://www.open-mesh.org/projects/batman-adv/wiki/BATMAN_V_Tests

 ...

With this patchset we finally introduce our new routing protocol:
B.A.T.M.A.N. V. Its implementation started quite some years ago,
but due to the big changes being introduced it took a while to be
discussed, designed, worked, re-worked, tested and debugged (well,
we're never done with the latest). The entire operation has
basically been a team work involving all the core contributors
together with other people interested in the project.

The new protocol is divided into two main subcomponents, called
respectively ELP and OGMv2. The former is in charge of
dealing with the neighbour discovery and link quality estimation,
while the latter implements the algorithm that spreads the
metrics around the network and computes optimal paths.

The biggest change introduced with B.A.T.M.A.N. V is the new
metric: the protocol won't rely on packet loss anymore, but it
will use the estimated throughput extracted directly from the
wifi driver (when available) by querying cfg80211.
Batman-adv will also send some unicast probing packets when
an interface is not used for payload traffic to make sure that
such values are current.

The new protocol can be compiled-in or not like other
features we have and when selected will pull in CFG80211 as
dependency for the reason described above.

Thanks to the big work brought up in the past by Marek Lindner,
batman-adv can easily deal several protocol implementations,
therefore compiling in this new version does not exclude the
older.
This means that the user is offered the option to choose
the protocol when creating the mesh interface (default is the
old one to keep backward compatibility).

Along with the protocol there are some sysfs knobs that are
introduced to fine tune some of its behaviours, but users
are recommended to keep the default values unless they know
what they are doing.

The last patch is about advertising our own patchwork platform
(thanks to Sven Eckelmann for having set that up!) in the
MAINTAINERS file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since offset is zero, it's not necessary to use set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

  CC [M]  net/sched/sch_mqprio.o
net/sched/sch_mqprio.c: In function ?mqprio_init?:
net/sched/sch_mqprio.c:145: error: unknown field ?tc? specified in initializer
net/sched/sch_mqprio.c:145: warning: missing braces around initializer
net/sched/sch_mqprio.c:145: warning: (near initialization for ?tc.<anonymous>?)
make[2]: *** [net/sched/sch_mqprio.o] Error 1
make[1]: *** [net/sched] Error 2
make: *** [net] Error 2

Several people reported this, surround the unnamed union
member initialization with braces to fix.
Signed-off-by: David S. Miller <davem@davemloft.net>

of_mdiobus_register()  declares the 'paddr' variable to hold the result of
the of_get_property()  but only uses it once after that while the function
can be called directly from the *if* statement. Remove that variable and
switch to calling of_find_property() instead since  we don't care about
the "reg" property's value anyway...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: Attention support patch series

Until now we've only enabled attention generation for the sake of
management firmware indications [required for link notifications].

This series enables [almost] all the attention sources of the HW,
currently for the sake of logging information relating to issues
experienced by HW. In future, infrastructure laid here would also be used
for the sake of the recovery process.

The first patch in the series is a semantic alignemnt of the code.
The later 3 patches incremently create said infrastructure and enrich
the logged information.
Notice #3 contains quite a bit of structures [consisting of ~1K lines]
that will eventually be removed and incorporated in the binary fw file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch utilizes the attention infrastructure to log additional
information that relates only to specific HW blocks.
For some of those HW blocks, it also stops automatically disabling the
attention generation as the attention is considered benign and thus
should only be logged; No fear of it flooding the system.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each HW block contains common information about attention reasons,
raising a bit for each one of the different sub-reasons that caused it
to raise an attention.

This patch extends the infrastructure by allowing logging of the various
reasons causing the HW blocks to generate an attention.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HW is capable of generating attentnions for a multitude of reasons,
but current driver is enabling attention generation only for management
firmware [required for link notifications].

This patch enables almost all of the possible reasons for HW attentions,
logging the HW block generating the attention and preventing further
attentions from that source [to prevent possible attention flood].
It also lays the infrastructure for additional exploration of the various
attentions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 52bd2d62 ("net: better skb->sender_cpu and skb->napi_id cohabitation")
skb_sender_cpu_clear() becomes empty and can be removed.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 driver updates

This series includes some bug fixes and updates for the mlx5 core
and ethernet driver.

From Gal, two fixes that protects the update CQ moderation flows
when it is not allowed.

From Moshe, two fixes for the core and ethernet driver in
non-cached(NC) and write combining(WC) buffers mappings,
which prevents the driver from double memory mappings.

From Or, reduce the firmware command completion timeout.

From Tariq, several small trivial fixes.

Changes from v0:
	- "Fix global UAR mapping" commit messages updated to explain ARCH_HAS_IOREMAP_WC usage.
	- rebased to commit 8d3f2806 'Merge branch ethtool-ksettings'

Changes from v1:
	- Removed ARCH_HAS_IOREMAP_WC config flag from "Fix global UAR mapping" commit,	as it was not accurate to use it.
	- Squashed "Fix global UAR mapping" and "net/mlx5: Avoid double mapping of io mapped memory"
	- Added more info for "Fix global UAR mapping" in commit message

Changes from v2:
	- None. resubmission per Dave's request due to two parallel submissions to mlx5 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid double mapping of io mapped memory, Device page may be
mapped to non-cached(NC) or to write-combining(WC).
The code before this fix tries to map it both to WC and NC
contrary to what stated in Intel's software developer manual.

Here we remove the global WC mapping of all UARS
"dev->priv.bf_mapping", since UAR mapping should be decided
per UAR (e.g we want different mappings for EQs, CQs vs QPs).

Caller will now have to choose whether to map via
write-combining API or not.

mlx5e SQs will choose write-combining in order to perform
BlueFlame writes.

Fixes: 88a85f99 ('TX latency optimization to save DMA reads')
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Reviewed-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The command timeout is terribly long, whole two hours. Make it 60s so if
things do go wrong, the user gets feedback in relatively short time, so
they can take corrective actions and/or investigate using tools and such.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling mlx5e_set_coalesce while the interface is down will result in
modifying CQs that don't exist.

Fixes: f62b8bb8 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If CQ moderation is not supported by the device, print a warning on
netdevice load, and return error when trying to modify/query cq
moderation via ethtool.

Fixes: f62b8bb8 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>