- 20 Apr, 2020 20 commits
-
-
Andrew Lunn authored
Measurements of the MDIO bus have shown that driving the MDIO bus using interrupts is slow. Back to back MDIO transactions take about 90us, with 25us spent performing the transaction, and the remainder of the time the bus is idle. Replacing the completion interrupt with polled IO results in back to back transactions of 40us. The polling loop waiting for the hardware to complete the transaction takes around 28us. Which suggests interrupt handling has an overhead of 50us, and polled IO nearly halves this overhead, and doubles the MDIO performance. Suggested-by: Chris Heally <cphealy@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Inline rtl8169_make_unusable_by_asic() and simplify it: - Address field doesn't need to be poisoned because descriptor is owned by CPU now - desc->opts1 is set by rtl8169_mark_to_asic() and rtl8169_rx_fill(), therefore we don't have to preserve any field parts. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
rtl8169_mark_as_last_descriptor() has just one user, so inline it. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 1GbE Intel Wired LAN Driver Updates 2020-04-19 This series contains updates to e1000e and igc only. Sasha adds new device IDs supported by the igc driver. Vitaly fixes the S0ix entry and exit flows in e1000e for TGP and newer MAC types when a cable is connected. Andre has the remaining changes in the series, starting with cleanup of the igc driver of duplicate code. Added a check for IGC_MAC_STATE_SRC_ADDR flag which is unsupported for MAC filters in igc. Cleaned up the return values for igc_add_mac_filter(), where the return value was not being used, so update the function to only return success or failure. Fix the return value of igc_uc_unsync() as well. Refactor the igc driver in several functions to help reduce the convoluted logic and simplify the driver filtering mechanisms. Improve the MAC address checks when adding a MAC filter. Lastly, improve the log messages related to MAC address filtering to ease debugging. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Aishwarya Ramakrishnan authored
Remove casting the values returned by memory allocation function. Coccinelle emits WARNING: casting value returned by memory allocation function to struct pointer is useless. This issue was detected by using the Coccinelle. Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com> Acked-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Aishwarya Ramakrishnan authored
Remove casting the values returned by memory allocation function. Coccinelle emits WARNING: casting value returned by memory allocation function to (struct cas_init_block *) is useless. This issue was detected by using the Coccinelle software. Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dejin Zheng authored
use devm_platform_get_and_ioremap_resource() to simplify code, which contains platform_get_resource() and devm_ioremap_resource(), it also get the resource for use by the following code. Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lourdes Pedrajas authored
Add PMTU discovery tests for these encapsulations: - IPIP - SIT, mode ip6ip - ip6tnl, modes ip6ip6 and ipip6 Signed-off-by: Lourdes Pedrajas <lu@pplo.net> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Walle authored
Don't use internal knowledge of the mdio bus core, instead use mdiobus_get_phy() which does the same thing. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Two small changes Patch #1 increases the scale of supported IPv6 nexthops groups when each group has one nexthop and all are using the same nexthop device, but with a different gateway IP. Patch #2 adjusts a register definition in accordance with recent firmware changes. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
The Infrastructure Entry Delete Register (IEDR) is used to delete entries stored in the KVD linear database. Currently, it is only possible to delete entries of size up to 2048. Future firmware versions will support deletion of entries of size up to 4096. Increase the size of the field so that the driver will be able to perform such deletions in the future, when required. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
As explained in commit fc25996e ("mlxsw: spectrum_router: Increase scale of IPv6 nexthop groups"), each nexthop group is hashed by XOR-ing the interface indexes of all the member nexthop devices. To avoid many different nexthop groups ending up using the same key, the above commit started hashing the interface indexes themselves before they are XOR-ed. However, in cases in which there are many nexthop groups that all use the same nexthop device and only differ in the gateway IP, we can still end up in a situation in which all the groups are using the same key. This eventually leads to -EBUSY error from rhashtable during insertion. Improve the situation by also making the gateway IP part of the key. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alex Veber <alexve@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Tested-by: Alex Veber <alexve@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
If a bus->reset() call for the mii_bus structure returns an error (e.g.: -EPROE_DEFER) we should propagate it accordingly. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Heiner Kallweit says: ==================== net: phy: realtek: move PHY resume delay from MAC to PHY driver Internal PHY's from RTL8168h up may not be instantly ready after calling genphy_resume(). So far r8169 network driver adds the needed delay, but better handle this in the PHY driver. The network driver may miss other places where the PHY is resumed. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
The Realtek PHY driver takes care of adding the needed delay now, therefore we can remove the delay here. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Internal PHY's from RTL8168h up may not be instantly ready after calling genphy_resume(). So far r8169 network driver adds the needed delay, but better handle this in the PHY driver. The network driver may miss other places where the PHY is resumed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jason Yan authored
Fix the following coccicheck warning: drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:700:2-8: WARNING: Assignment of 0/1 to bool variable drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:702:2-8: WARNING: Assignment of 0/1 to bool variable Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YueHaibing authored
Fix sparse warnings: drivers/ptp/ptp_idt82p33.c:26:5: warning: symbol 'sync_tod_timeout' was not declared. Should it be static? drivers/ptp/ptp_idt82p33.c:31:5: warning: symbol 'phase_snap_threshold' was not declared. Should it be static? Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YueHaibing authored
Fix sparse warning: drivers/ptp/ptp_kvm.c:25:1: warning: symbol 'kvm_ptp_lock' was not declared. Should it be static? Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
Some boards do not have the RX_ER MII signal connected. Normally in such situation, those pins would be grounded, but then again, some boards left it electrically floating. When sending traffic to those switch ports, one can see that the N_SOFERR statistics counter is incrementing once per each packet. The user manual states for this counter that it may count the number of frames "that have the MII error input being asserted prior to or up to the SOF delimiter byte". So the switch MAC is sampling an electrically floating signal, and preventing proper traffic reception because of that. As a workaround, enable the internal weak pull-downs on the input pads for the MII control signals. This way, a floating signal would be internally tied to ground. The logic levels of signals which _are_ externally driven should not be bothered by this 40-50 KOhm internal resistor. So it is not an issue to enable the internal pull-down unconditionally, irrespective of PHY interface type (MII, RMII, RGMII, SGMII) and of board layout. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 19 Apr, 2020 20 commits
-
-
Andre Guedes authored
This patch adds log messages to functions related to the MAC address filtering code to ease debugging. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
This patch does a code refactoring in igc_del_mac_filter() so it uses the new helper igc_find_mac_filter() and improves the comment about the special handling when deleting the default filter. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
The helper igc_mac_entry_can_be_used() implementation is a bit convoluted since it does two different things: find a not-in-use slot in mac_table or find an in-use slot where the address and address type match. This patch does a code refactoring and break it up into two helper functions. With this patch we might traverse mac_table twice in some situations, but this is not harmful performance-wise (mac_table has only 16 entries and adding mac filters is not hot-path), and it improves igc_add_mac_ filter() readability considerably. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
With the previous two patches, igc_add_mac_steering_filter() and igc_del_mac_steering_filter() became a pointless wrapper of igc_add_mac_filter() and igc_del_mac_filter(). This patch removes these wrappers and update callers to call igc_add_mac_filter() and igc_del_mac_filter() directly. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
The IGC_MAC_STATE_QUEUE_STEERING bit in mac_table[i].state is utilized to indicate that frames matching the filter are assigned to mac_table[i].queue. This bit is not strictly necessary since we can convey the same information as follows: queue == -1 means queue assignment is disabled, otherwise it is enabled. In addition to make the code simpler, this change fixes some awkward situations where we pass a complete misleading 'queue' value such as in igc_uc_sync(). So this patch removes IGC_MAC_STATE_QUEUE_STEERING and also takes the opportunity to improve the igc_add_mac_filter documentation. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
igc_add_mac_filter() doesn't allow us to have more than one entry with the same address and address type in adapter->mac_table so checking if 'queue' matches in igc_del_mac_filter() isn't necessary. This patch removes that check. This patch also takes the opportunity to improve the igc_del_mac_filter documentation and remove comment which is not applicable to this I225 controller. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
igc_add_mac_filter() doesn't allow filters with invalid MAC address to be added to adapter->mac_table so, in igc_del_mac_filter(), we can early return if MAC address is invalid. No need to traverse the table. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
Current igc_rar_set_index() implementation is a bit convoluted so this patch does some code refactoring to improve it. The helper igc_rar_set_index() is about writing MAC filter settings into hardware registers. Logic such as address validation belongs to functions upper in the call chain such as igc_set_mac() and igc_add_mac_filter(). So this patch moves the is_valid_ether_addr() call to igc_add_mac_filter(). No need to touch igc_set_mac() since it already checks it. The variables 'rar_low' and 'rar_high' represent the value in registers RAL and RAH so we rename them to 'ral' and 'rah', respectively, to match the registers names. To make it explicit, filter settings are passed as arguments to the function instead of reading them from adapter->mac_table "under the hood". Also, the function was renamed to igc_set_mac_filter_hw to make it more clear what it does. Finally, the patch removes some wrfl() calls and comments not needed. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
In case igc_del_mac_filter() returns error, that error is masked since the functions always return 0 (success). This patch fixes igc_uc_unsync() so it returns whatever value igc_del_mac_filter() returns (0 on success, negative number on error). Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
In case of success, igc_add_mac_filter() returns the index in adapter->mac_table where the requested filter was added. This information, however, is not used by any caller of that function. In fact, callers have extra code just to handle this returning index as 0 (success). So this patch changes the function to return 0 on success instead, and cleans up the extra code. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
The IGC_MAC_STATE_SRC_ADDR flags is not supported by igc_add_mac_ filter() so this patch adds a check for it and returns -ENOTSUPP in case it is set. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
This patch does a code refactoring in the MAC address filtering logic to get rid of some duplicate code. IGC driver has two functions to add MAC address filters that are pretty much the same: igc_add_mac_filter() and igc_add_mac_filter_flags(). The only difference is that the latter allows the callee to specify the 'flags' parameter while the former has it hard coded as zero. The same rationale applies to filter deletion counterparts. So this patch refactors igc_add_mac_filter() and igc_del_mac_filter() so they handle the 'flags' parameters, removes the _flags() functions, and fixes callees accordingly. Signed-off-by: Andre Guedes <andre.guedes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Vitaly Lifshits authored
Added a fix to S0ix entry and exit flows for TGP and above MAC types, to the case when the Ethernet cable is connected and the link is up. With that the system is able to reach SLP_S0 when going to freeze power state. Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Add new device IDs for the next step of i225 Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
David S. Miller authored
Heiner Kallweit says: ==================== r8169: series with improvements Again a series with few improvements. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Add workaround for hw issues with TSO on RTL8168evl. This workaround is based on information I got from Realtek, and *should* allow to safely enable TSO on this chip version. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Simplify the code and avoid the overhead of calling vlan_get_protocol(). Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
At that place in rtl_init_one() we can safely use rtl8169_set_features() to configure the chip according to the default features. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
So far we set RX_VLAN_8125 unconditionally, even if NETIF_F_HW_VLAN_CTAG_RX may not be set. Don't touch these bits, and let only rtl8169_set_features() control them. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
NETIF_F_HIGHDMA is added to vlan_features by register_netdev(), therefore we can omit this here. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-