Signed-off-by: Igal Liberman <igal.liberman@freescale.com>

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>

Edge-rate:
As system and networking speeds increase, a signal's output transition,
also know as the edge rate or slew rate (V/ns), takes on greater importance
because high-speed signals come with a price. That price is an assortment of
interference problems like ringing on the line, signal overshoot and
undershoot, extended signal settling times, crosstalk noise, transmission
line reflections, false signal detection by the receiving device and
electromagnetic interference (EMI) -- all of which can negate the potential
gains designers are seeking when they try to increase system speeds through
the use of higher performance logic devices. The fact is, faster signaling
edge rates can cause a higher level of electrical noise or other type of
interference that can actually lead to slower line speeds and lower maximum
system frequencies. This parameter allow the board designers to change the
driving strange, and thereby change the EMI behavioral.

Edge-rate parameters (vddmac, edge-slowdown) get from Device Tree.

Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3_reset_work() expects tx queues to be stopped (via
vmxnet3_quiesce_dev -> netif_tx_disable). However, this races with the
netif_wake_queue() call in netif_tx_timeout() such that the driver's
start_xmit routine may be called unexpectedly, triggering one of the BUG_ON
in vmxnet3_map_pkt with a stack trace like this:

RIP: 0010:[<ffffffffa00cf4bc>] vmxnet3_map_pkt+0x3ac/0x4c0 [vmxnet3]
 [<ffffffffa00cf7e0>] vmxnet3_tq_xmit+0x210/0x4e0 [vmxnet3]
 [<ffffffff813ab144>] dev_hard_start_xmit+0x2e4/0x4c0
 [<ffffffff813c956e>] sch_direct_xmit+0x17e/0x1e0
 [<ffffffff813c96a7>] __qdisc_run+0xd7/0x130
 [<ffffffff813a6a7a>] net_tx_action+0x10a/0x200
 [<ffffffff810691df>] __do_softirq+0x11f/0x260
 [<ffffffff81472fdc>] call_softirq+0x1c/0x30
 [<ffffffff81004695>] do_softirq+0x65/0xa0
 [<ffffffff81069b89>] local_bh_enable_ip+0x99/0xa0
 [<ffffffffa031ff36>] destroy_conntrack+0x96/0x110 [nf_conntrack]
 [<ffffffff813d65e2>] nf_conntrack_destroy+0x12/0x20
 [<ffffffff8139c6d5>] skb_release_head_state+0xb5/0xf0
 [<ffffffff8139d299>] skb_release_all+0x9/0x20
 [<ffffffff8139cfe9>] __kfree_skb+0x9/0x90
 [<ffffffffa00d0069>] vmxnet3_quiesce_dev+0x209/0x340 [vmxnet3]
 [<ffffffffa00d020a>] vmxnet3_reset_work+0x6a/0xa0 [vmxnet3]
 [<ffffffff8107d7cc>] process_one_work+0x16c/0x350
 [<ffffffff810804fa>] worker_thread+0x17a/0x410
 [<ffffffff810848c6>] kthread+0x96/0xa0
 [<ffffffff81472ee4>] kernel_thread_helper+0x4/0x10
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2016-10-02

This series contains updates to fm10k only.

Jake fixes an issue where PTP applications requesting software timestamps
may complain that the requested mode is not supported, so add a generic
callback for those drivers that have software transmit timestamp support
enabled.  Then provides a trivial cleanup where a code was not wrapped
properly.  Got make sure that code looks good in a 80 character limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Although rare, it's possible to hit PCI error early on device
probe, meaning possibly some structs are not entirely initialized,
and some might even be completely uninitialized, leading to NULL
pointer dereference.

The i40e driver currently presents a "bad" behavior if device hits
such early PCI error: firstly, the struct i40e_pf might not be
attached to pci_dev yet, leading to a NULL pointer dereference on
access to pf->state.

Even checking if the struct is NULL and avoiding the access in that
case isn't enough, since the driver cannot recover from PCI error
that early; in our experiments we saw multiple failures on kernel
log, like:

  [549.664] i40e 0007:01:00.1: Initial pf_reset failed: -15
  [549.664] i40e: probe of 0007:01:00.1 failed with error -15
  [...]
  [871.644] i40e 0007:01:00.1: The driver for the device stopped because the
  device firmware failed to init. Try updating your NVM image.
  [871.644] i40e: probe of 0007:01:00.1 failed with error -32
  [...]
  [872.516] i40e 0007:01:00.0: ARQ: Unknown event 0x0000 ignored

Between the first probe failure (error -15) and the second (error -32)
another PCI error happened due to the first bad probe. Also, driver
started to flood console with those ARQ event messages.

This patch will prevent these issues by allowing error recovery
mechanism to remove the failed device from the system instead of
trying to recover from early PCI errors during device probe.

CC: <stable@vger.kernel.org>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2016-10-03

This series contains fixes to i40e only.

Stefan Assmann provides the changes in this series to resolve an issue
where when we run out of MSIx vectors, iWARP gets disabled automatically.
First adds a check for "no vectors left" during MSIx vector allocation
for VMDq, which will prevent more vectors being allocated than available.
Then fixed the MSIx vector redistribution when we reach the hardware limit
for vectors so that additional features like VMDq, iWARP, etc do not get
starved for vectors because the PF is hogging all the resources.  Lastly,
fix the issue for flow director by moving the check for the reaching the
vector limit earlier in the code so that a decision can be made on
disabling flow director.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed*: Add qedr infrastructure support

In the last couple of weeks we've been sending RFCs for the qedr
driver - the RoCE driver for QLogic FastLinQ 4xxxx line of adapters.
Latest RFC can be found at [1].

At Doug's advice [2], we've decided to split the series into two:
 - first part contains the qed backbone that's necessary for all the
configurations relating to the qedr driver, as well as the qede
infrastructure that is used for communication between the qedr and qede.
 - Second part consists of the actual qedr driver and introduces almost
no changes to qed/qede.

This is the first of said two parts. The second half would be sent
later this week.

The only 'oddity' in the devision are the Kconfig options -
As this series introduces both LL2 and QEDR-based logic in qed/qede,
I wanted to add the CONFIG_INFINIBAND_QEDR option here [with default n].
Otherwise, a lot of the code introduced would be dead-code [won't even
be compiled] until qedr is accepted.
As a result I've placed the config option in an odd place - under
qlogic's Kconfig. The second series would then remove that option
and add it in its correct place under the infiniband Kconfig.
[I'm fine with pushing it there to begin with, but I didn't want to
'contaminate' non-qlogic configuration files with half-baked options].

Dave - I don't think you were E-mailed with Doug's suggestion.
I think the notion was to have the two halves accepted side-by-side,
but actually the first has no dependency issues, so it's also
possible to simply take this first to net-next, and push the qedr
into rdma once it's merged. But it's basically up to you and Doug;
We'd align with whatever suits you best.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the RoCE-specific LL2 logic [as well as GSI support] over
the 'generic' LL2 interface.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add slowpath configuration support for user, dma and memory
regions registration.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the slowpath configurations of Queue Pair verbs
which adds, deletes, modifies and queries Queue Pairs.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the configurations of the protection domain and
completion queues.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the backbone required for the various HW initalizations
which are necessary for the qedr driver - FW notification, resource
initializations, etc.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds a skeletal implementation of the qede RoCE driver -
The qedr has some dependencies of the state of the underlying base
interface. This adds some logic required with mutual registrations
and the ability to pass updates on 'intresting' events.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Other protocols beside the networking driver need the ability
of passing some L2 traffic, usually [although not limited] for the
purpose of some management traffic.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently if the MSI-X vector limit is reached the sideband flow
director gets disabled. A bit too early to make that decision, as
vectors may get re-distributed. So move the check further back.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver allocates 1 vector per CPU thread and the current hardware
limit for vectors is 129 per PF. On systems with 128 or more threads
this currently means all vectors are used by the PF leaving no room for
additional features like VMDq, iWARP, etc...
The code that should redistribute the vectors in this case is broken and
never triggers. Fixed the code so that it actually triggers if the
hardware limit is reached and adjust the number of queue pairs
accordingly.
Also the number of initially requested iWARP vectors was not properly
saved when the vector limit was reached, and therefore always zero.

Comparison with debug statement.
Before:
i40e 0000:2d:00.0: VMDq disabled, not enough MSI-X vectors
i40e 0000:2d:00.0: IWARP disabled, not enough MSI-X vectors
i40e 00.0 MSI-X vector distribution: PF 128, VMDq 0, FDSB 0, iWARP 0
After:
i40e 0000:2d:00.0: MSI-X vector limit reached, attempting to redistribute vectors
i40e 00.0 MSI-X vector distribution: PF 78, VMDq 8, FDSB 0, iWARP 42
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During MSI-X vector allocation for VMDq, a check for "no vectors left"
was missing, add it. This prevents more vectors to be allocated than
available.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A call to 'ida_simple_remove()' is missing in the error handling path.

This as been spotted with the following coccinelle script which tries to
detect missing 'ida_simple_remove()' call in error handling paths.

///////////////
@@
expression x;
identifier l;
@@

*   x = ida_simple_get(...);
    ...
    if (...) {
    ...
    }
    ...
    if (...) {
       ...
       goto l;
    }
    ...
*   l: ... when != ida_simple_remove(...);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of error, the function ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.

Also add check for return value of platform_get_resource().

Fixes: 54e19bc7 ("net: qcom/emac: do not use devm on internal
phy pdev")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_vlan_pop/push were too generic, trying to support the cases where
skb->data is at mac header, and cases where skb->data is arbitrarily
elsewhere.

Supporting an arbitrary skb->data was complex and bogus:
 - It failed to unwind skb->data to its original location post actual
   pop/push.
   (Also, semantic is not well defined for unwinding: If data was into
    the eth header, need to use same offset from start; But if data was
    at network header or beyond, need to adjust the original offset
    according to the push/pull)
 - It mangled the rcsum post actual push/pop, without taking into account
   that the eth bytes might already have been pulled out of the csum.

Most callers (ovs, bpf) already had their skb->data at mac_header upon
invoking skb_vlan_pop/push.
Last caller that failed to do so (act_vlan) has been recently fixed.

Therefore, to simplify things, no longer support arbitrary skb->data
inputs for skb_vlan_pop/push().

skb->data is expected to be exactly at mac_header; WARN otherwise.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Pravin Shelar <pshelar@ovn.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Generic skb_vlan_push/skb_vlan_pop functions don't properly handle the
case where the input skb data pointer does not point at the mac header:

- They're doing push/pop, but fail to properly unwind data back to its
  original location.
  For example, in the skb_vlan_push case, any subsequent
  'skb_push(skb, skb->mac_len)' calls make the skb->data point 4 bytes
  BEFORE start of frame, leading to bogus frames that may be transmitted.

- They update rcsum per the added/removed 4 bytes tag.
  Alas if data is originally after the vlan/eth headers, then these
  bytes were already pulled out of the csum.

OTOH calling skb_vlan_push/skb_vlan_pop with skb->data at mac_header
present no issues.

act_vlan is the only caller to skb_vlan_*() that has skb->data pointing
at network header (upon ingress).
Other calles (ovs, bpf) already adjust skb->data at mac_header.

This patch fixes act_vlan to point to the mac_header prior calling
skb_vlan_*() functions, as other callers do.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Pravin Shelar <pshelar@ovn.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial change here to cleanup a checkpatch.pl warning that got
introduced when changing to alloc_workqueue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There is no need to clk_disable_unprepare(dev->clk)
before it was initialized.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160930' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: More fixes and adjustments

This set of patches contains some more fixes and adjustments:

 (1) Actually display the retransmission indication previously added to the
     tx_data trace.

 (2) Switch to Congestion Avoidance mode properly at cwnd==ssthresh rather
     than relying on detection during an overshoot and correction.

 (3) Reduce ssthresh to the peer's declared receive window.

 (4) The offset field in rxrpc_skb_priv can be dispensed with and the error
     field is no longer used.  Get rid of them.

 (5) Keep the call timeouts as ktimes rather than jiffies to make it easier
     to deal with RTT-based timeout values in future.  Rounding to jiffies
     is still necessary when the system timer is set.

 (6) Fix the call timer handling to avoid retriggering of expired timeout
     actions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Benc says:

====================
openvswitch: mpls fix and clean up

Convert to the new mpls skb layout the last remaining place in openvswitch,
forgotten on the mpls GSO rework. The GSO rework also allows for some
cleanup in the third patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_mpls_header is equivalent to mpls_hdr now. Use the existing helper
instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will be also used by openvswitch.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the 48d2ab60 ("net: mpls: Fixups for GSO"), MPLS handling in
openvswitch was changed to have network header pointing to the start of the
MPLS headers and inner_network_header pointing after the MPLS headers.

However, key_extract was missed by the mentioned commit, causing incorrect
headers to be set when a MPLS packet just enters the bridge or after it is
recirculated.

Fixes: 48d2ab60 ("net: mpls: Fixups for GSO")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If fi->fib_nhs is zero, the router interface pointer is uninitialized, as shown by
this warning:

drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c: In function 'mlxsw_sp_router_fib_event':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:1674:21: error: 'r' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:1643:23: note: 'r' was declared here

This changes the loop so we handle the case the same way as finding no router
interface pointer attached to one of the nexthops to ensure we always
trap here instead of using uninitialized data.

Fixes: b45f64d1 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Build-testing this driver with -Wmaybe-uninitialized gives a new false-positive
warning that I can't really explain:

drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function 'mlx5e_configure_flower':
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:509:3: error: 'old_attr' may be used uninitialized in this function [-Werror=maybe-uninitialized]

It's obvious from the code that 'old_attr' is initialized whenever 'old'
is non-NULL here. The warning appears with all versions I tested from gcc-4.7
through gcc-6.1, and I could not come up with a way to rewrite the function
in a more readable way that avoids the warning, so I'm adding another
initialization to shut it up.

Fixes: 8b32580d ("net/mlx5e: Add TC vlan action for SRIOV offloads")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This generic callback is for drivers which have software Tx timestamp
support enabled. Without this, PTP applications requesting software
timestamps may complain that the requested mode is not supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A recent cleanup marked cxgb4_dcb_enabled as 'static', which is correct, but this ignored
how the symbol is also exported. In addition, the export can be compiled out when modules
are disabled, causing a harmless compiler warning in configurations for which it is not
used at all:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:282:12: error: 'cxgb4_dcb_enabled' defined but not used [-Werror=unused-function]

This removes the export and moves the function into the correct #ifdef so we only build
it when there are users.

Fixes: 50935857 ("cxgb4: mark symbols static where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the newly added support for IFLA_VF_VLAN_LIST netlink messages,
we get a warning about potential uninitialized variable use in
the parsing of the user input when enabling the -Wmaybe-uninitialized
warning:

net/core/rtnetlink.c: In function 'do_setvfinfo':
net/core/rtnetlink.c:1756:9: error: 'ivvl$' may be used uninitialized in this function [-Werror=maybe-uninitialized]

I have not been able to prove whether it is possible to arrive in
this code with an empty IFLA_VF_VLAN_LIST block, but if we do,
then ndo_set_vf_vlan gets called with uninitialized arguments.

This adds an explicit check for an empty list, making it obvious
to the reader and the compiler that this cannot happen.

Fixes: 79aab093 ("net: Update API for VF vlan protocol 802.1ad support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 879c7220 ("net: pktgen: Observe needed_headroom
of the device") increased the 'pkt_overhead' field value by
LL_RESERVED_SPACE.
As a side effect the generated packet size, computed as:

	/* Eth + IPh + UDPh + mpls */
	datalen = pkt_dev->cur_pkt_size - 14 - 20 - 8 -
		  pkt_dev->pkt_overhead;

is decreased by the same value.
The above changed slightly the behavior of existing pktgen users,
and made the procfs interface somewhat inconsistent.
Fix it by restoring the previous pkt_overhead value and using
LL_RESERVED_SPACE as extralen in skb allocation.
Also, change pktgen_alloc_skb() to only partially reserve
the headroom to allow the caller to prefetch from ll header
start.

v1 -> v2:
 - fixed some typos in the comments

Fixes: 879c7220 ("net: pktgen: Observe needed_headroom of the device")
Suggested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the mac address origin is not dt, you can only safely assign a mac
address after "link up" of the device. If the link is off the clocks are
disabled and because of issues assigning registers when clocks are off the
new mac address cannot be written in .ndo_set_mac_address() on some soc's.
This fix sets the mac address unconditionally in fec_restart(...) and
ensures consistency between fec registers and the network layer.
Signed-off-by: Gavin Schenk <g.schenk@eckelmann.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 9638d19e ("net: fec: add netif status check before set mac address")
Signed-off-by: David S. Miller <davem@davemloft.net>

We get 2 warnings when building kernel with W=1:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:2041:5: warning: no previous prototype for 'mtk_get_link_ksettings' [-Wmissing-prototypes]
drivers/net/ethernet/mediatek/mtk_eth_soc.c:2052:5: warning: no previous prototype for 'mtk_set_link_ksettings' [-Wmissing-prototypes]

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get 1 warning when building kernel with W=1:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2715:5: warning: no previous prototype for 'cxgb_setup_tc' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is an effective no-op in terms of user observable behaviour.

By preventing the overwrite of non-null extra1/extra2 fields
in addrconf_sysctl() we can enable the use of proc_dointvec_minmax().

This allows us to eliminate the constant min/max (1..255) trampoline
function that is addrconf_sysctl_hop_limit().

This is nice because it simplifies the code, and allows future
sysctls with constant min/max limits to also not require trampolines.

We still can't eliminate the trampoline for mtu because it isn't
actually a constant (it depends on other tunables of the device)
and thus requires at-write-time logic to enforce range.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using bridge without bridge netfilter enabled the message
displayed is rather confusing and leads to belive that a deprecated
feature is in use. Use IS_MODULE to be explicit that the message only
affects users which use bridge netfilter as module and reword the
message.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>