Analyze and rework the PIO mode operation. The PIO mode operation
was unreliable on MX28, by analyzing the bus with LA, the checks
for when data were available or were to be sent were wrong.

The PIO WRITE has to be completely reworked as it multiple problems.
The MX23 datasheet helped here, see comments in the code for details.
The problems boil down to:
- RUN bit in CTRL0 must be set after DATA register was written
- The PIO transfer must be 4 bytes long tops, otherwise use
  clock stretching.
Both of these fixes are implemented.

The PIO READ operation can only be done for up to four bytes as
we are unable to read out the data from the DATA register fast
enough.

This patch also tries to document the investigation within the
code.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

It seems the PIO mode does not work, or at least not like it works
on a i.MX28. Each short transfer needs about one second (without an
error message) but does not send anything on the I2C lines.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The 'driver' field of the i2c_client struct is redundant. The same data can be
accessed through to_i2c_driver(client->dev.driver). The generated code for both
approaches in more or less the same.

E.g. on ARM the expression client->driver->command(...) generates

		...
		ldr     r3, [r0, #28]
		ldr     r3, [r3, #32]
		blx     r3
		...

and the expression to_i2c_driver(client->dev.driver)->command(...) generates

		...
		ldr     r3, [r0, #160]
    	ldr     r3, [r3, #-4]
    	blx     r3
		...

Other architectures will generate similar code.

All users of the 'driver' field outside of the I2C core have already been
converted. So this only leaves the core itself. This patch converts the
remaining few users in the I2C core and then removes the 'driver' field from the
i2c_client struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The 'driver' field of the i2c_client struct is redundant and is going to be
removed. Check i2c_client->dev.driver instead to see if a driver is bound to the
device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The 'driver' field of the i2c_client struct is redundant and is going to be
removed. Use 'to_i2c_driver(client->dev.driver)' instead to get direct
access to the i2c_driver struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The 'driver' field of the i2c_client struct is redundant and is going to be
removed. Use 'to_i2c_driver(client->dev.driver)' instead to get direct access to
the i2c_driver struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later. To get direct access to the i2c_driver struct use
'to_i2c_driver(client->dev.driver)'.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch moves the at24.h header from include/linux/i2c to
include/linux/platform_data and updates existing support accordingly.

It also fixes the following checkpatch warning:

    WARNING: please, no space before tabs
    #436: FILE: include/linux/platform_data/at24.h:31:
    + * ^Iu8 *mac_addr = ethernet_pdata->mac_addr;$
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Using the same clock for all device instances is non-portable and obtaining
clock references by an ID without using a device pointer is discouraged.
This is also not needed, because on platforms, where this driver is used,
suitable clocks are available for the I2C controllers, that are children of
the peripheral clock and just pass its rate 1-to-1 to controllers. This
patch switches the driver to obtain references to correct clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

When clk_get() fails, it returns an error code, not a NULL. This patch
fixes such an error handling bug.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch adds Device Tree support to the i2c-rcar driver and respective
documentation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

There is no need to repeatedly query clock frequency, where it is not
expected to change. The complete loop can also trivially be replaced with
a simple division. A further loop below the one, being simplified, could
also be replaced, but that would get more complicated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

A recent patch added even more superfluous parenthesis to those, which
already were there. Remove them again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The 'name' attribute is needed for all i2c-dev class devices, meaning
it can be created automatically by pointing to it in the class data
structure. This simplifies the code and reduces the probability for race
conditions (the name attribute should exist by the time the device is
announced to user space).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull USB fixes from Greg KH:
 "Here are a number of USB driver fixes for 3.12-rc3.

  These are all for host controller issues that have been reported, and
  there's a fix for an annoying error message that gets printed every
  time you remove a USB 3 device from the system that's been bugging me
  for a while"

* tag 'usb-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: dwc3: add support for Merrifield
  USB: fsl/ehci: fix failure of checking PHY_CLK_VALID during reinitialization
  USB: Fix breakage in ffs_fs_mount()
  fsl/usb: Resolve PHY_CLK_VLD instability issue for ULPI phy
  usb/core/devio.c: Don't reject control message to endpoint with wrong direction bit
  usb: chipidea: USB_CHIPIDEA should depend on HAS_DMA
  usb: chipidea: udc: free pending TD at removal procedure
  usb: chipidea: imx: Add usb_phy_shutdown at probe's error path
  usb: chipidea: Fix memleak for ci->hw_bank.regmap when removal
  usb: chipidea: udc: fix the oops after rmmod gadget
  USB: fix PM config symbol in uhci-hcd, ehci-hcd, and xhci-hcd
  USB: OHCI: accept very late isochronous URBs
  USB: UHCI: accept very late isochronous URBs
  USB: iMX21: accept very late isochronous URBs
  usbcore: check usb device's state before sending a Set SEL control transfer
  xhci: Fix race between ep halt and URB cancellation
  usb: Fix xHCI host issues on remote wakeup.
  xhci: Ensure a command structure points to the correct trb on the command ring
  xhci: Fix oops happening after address device timeout

Pull tty/serial fixes from Greg KH:
 "Here are some serial at tty driver fixes for 3.12-rc3

  The serial driver fixes some kref leaks, documentation is moved to the
  proper places, and the tty and n_tty fixes resolve some reported
  regressions.  There is still one outstanding tty regression fix that
  isn't in here yet, as I want to test it out some more, it will be sent
  for 3.12-rc4 if it checks out"

* tag 'tty-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: ar933x_uart: move devicetree binding documentation
  tty: Fix SIGTTOU not sent with tcflush()
  n_tty: Fix EOF push index when termios changes
  serial: pch_uart: remove unnecessary tty_port_tty_get
  serial: pch_uart: fix tty-kref leak in dma-rx path
  serial: pch_uart: fix tty-kref leak in rx-error path
  serial: tegra: fix tty-kref leak

Pull staging fixes from Greg KH:
 "Here are some staging driver fixes, MAINTAINER updates, and a new
  device id.  All of these have been in the linux-next tree, and are
  pretty simple patches"

* tag 'staging-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8188eu: Add new device ID
  staging: imx-drm: Fix probe failure
  staging: vt6656: [BUG] iwctl_siwencodeext return if device not open
  staging: vt6656: [BUG] main_usb.c oops on device_close move flag earlier.
  staging: vt6656: rxtx.c [BUG] s_vGetFreeContext dead lock on null apTD.
  Staging: rtl8192u: r819xU_cmdpkt: checking NULL value after doing dev_alloc_skb
  staging: usbip: Orphan usbip
  staging: r8188eu: Add files for new drive: Cocci spatch "noderef"
  staging: r8188eu: Cocci spatch "noderef"
  staging: octeon-usb: Cocci spatch "noderef"
  staging: r8188eu: Add files for new drive: Cocci spatch "noderef"
  MAINTAINERS: staging: dgnc and dgap drivers: add maintainer
  staging: lustre: Cocci spatch "noderef"

Merge tag 'driver-core-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core / sysfs fixes from Greg KH:
 "Here are 2 fixes for 3.12-rc3.  One fixes a sysfs problem with
  mounting caused by 3.12-rc1, and the other is a bug reported by the
  chromeos developers with the driver core.

  Both have been in linux-next for a bit"

* tag 'driver-core-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core : Fix use after free of dev->parent in device_shutdown
  sysfs: Allow mounting without CONFIG_NET

Pull char/misc driver fixes from Greg KH:
 "Here are some HyperV and MEI driver fixes for 3.12-rc3.  They resolve
  some issues that people have been reporting for them"

* tag 'char-misc-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Drivers: hv: vmbus: Terminate vmbus version negotiation on timeout
  Drivers: hv: util: Correctly support ws2008R2 and earlier
  mei: cancel stall timers in mei_reset
  mei: bus: stop wait for read during cl state transition
  mei: make me client counters less error prone

Pull perf revert from Ingo Molnar:
 "This fixes the 'perf top' regression Markus Trippelsdorf reported"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "perf symbols: Demangle cloned functions"

Pull drm fixes from Dave Airlie:
 "Nothing too major, radeon still has some dpm changes for off by
  default.

  Radeon, intel, msm:
   - radeon: a few more dpm fixes (still off by default), uvd fixes
   - i915: runtime warn backtrace and regression fix
   - msm: iommu changes fallout"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (27 commits)
  drm/msm: use drm_gem_dumb_destroy helper
  drm/msm: deal with mach/iommu.h removal
  drm/msm: Remove iommu include from mdp4_kms.c
  drm/msm: Odd PTR_ERR usage
  drm/i915: Fix up usage of SHRINK_STOP
  drm/radeon: fix hdmi audio on DCE3.0/3.1 asics
  drm/i915: preserve pipe A quirk in i9xx_set_pipeconf
  drm/i915/tv: clear adjusted_mode.flags
  drm/i915/dp: increase i2c-over-aux retry interval on AUX DEFER
  drm/radeon/cik: fix overflow in vram fetch
  drm/radeon: add missing hdmi callbacks for rv6xx
  drm/i915: Use a temporary va_list for two-pass string handling
  drm/radeon/uvd: lower msg&fb buffer requirements on UVD3
  drm/radeon: disable tests/benchmarks if accel is disabled
  drm/radeon: don't set default clocks for SI when DPM is disabled
  drm/radeon/dpm/ci: filter clocks based on voltage/clk dep tables
  drm/radeon/dpm/si: filter clocks based on voltage/clk dep tables
  drm/radeon/dpm/ni: filter clocks based on voltage/clk dep tables
  drm/radeon/dpm/btc: filter clocks based on voltage/clk dep tables
  drm/radeon/dpm: fetch the max clk from voltage dep tables helper
  ...

This reverts commit de95ab53.

Markus Trippelsdorf reported that this commit broke 'perf top':

 > I just see a gray screen with no text at all. Sometimes the
 > following error messages are printed:
 >
 >  *** Error in `perf': invalid fastbin entry (free): 0x00000000029b18c0
 >  ***
 >  *** Error in `perf': malloc(): memory corruption (fast): 0x0000000000ee0b10 ***

While this code is fixable, the commit itself fails on several levels:

 - it should have been a separate helper function
 - why the heck does it do strchr() twice
 - it casts a const char * over into char *
 - sloppy style
 - it's not even a regression fix!

So lets revert it and re-try the patch in v3.13.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

A small fix + deal with fallout of iommu changes + use new
drm_gem_dumb_destroy helper.

* 'msm-fixes-3.12-rc2' of git://people.freedesktop.org/~robclark/linux:
  drm/msm: use drm_gem_dumb_destroy helper
  drm/msm: deal with mach/iommu.h removal
  drm/msm: Remove iommu include from mdp4_kms.c
  drm/msm: Odd PTR_ERR usage

Merge branches 'sched-urgent-for-linus', 'timers-urgent-for-linus' and 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull scheduler, timer and x86 fixes from Ingo Molnar:
 - A context tracking ARM build and functional fix
 - A handful of ARM clocksource/clockevent driver fixes
 - An AMD microcode patch level sysfs reporting fixlet

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  arm: Fix build error with context tracking calls

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: em_sti: Set cpu_possible_mask to fix SMP broadcast
  clocksource: of: Respect device tree node status
  clocksource: exynos_mct: Set IRQ affinity when the CPU goes online
  arm: clocksource: mvebu: Use the main timer as clock source from DT

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode/AMD: Fix patch level reporting for family 15h

Pull perf fixes from Ingo Molnar:
 "A couple of tooling fixlets and a PMU detection printout fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86: Fix PMU detection printout when no PMU is detected
  perf symbols: Demangle cloned functions
  perf machine: Fix path unpopulated in machine__create_modules()
  perf tools: Explicitly add libdl dependency
  perf probe: Fix probing symbols with optimization suffix
  perf trace: Add mmap2 handler
  perf kmem: Make it work again on non NUMA machines

Pull xfs bugfixes from Ben Myers:
 - fix for directory node collapse regression
 - fix for recovery over stale on disk structures
 - fix for eofblocks ioctl
 - fix asserts in xfs_inode_free
 - lock the ail before removing an item from it

* tag 'xfs-for-linus-v3.12-rc3' of git://oss.sgi.com/xfs/xfs:
  xfs: fix node forward in xfs_node_toosmall
  xfs: log recovery lsn ordering needs uuid check
  xfs: fix XFS_IOC_FREE_EOFBLOCKS definition
  xfs: asserting lock not held during freeing not valid
  xfs: lock the AIL before removing the buffer item

Pull i2c fixes from Wolfram Sang:
 "Some driver bugfixes for the I2C subsystem"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: ismt: initialize DMA buffer
  i2c: designware: 10-bit addressing mode enabling if I2C_DYNAMIC_TAR_UPDATE is set
  i2c: mv64xxx: Do not use writel_relaxed()
  i2c: mv64xxx: Fix some build warnings
  i2c: s3c2410: fix clk_disable/clk_unprepare WARNings

Pull ACPI and power management fixes from Rafael Wysocki:
 "These fix one recent cpufreq regression, a few older bugs that may
  harm users and a kerneldoc typo.

  Specifics:

   1) After the recent locking changes in the cpufreq core it is
      possible to trigger BUG_ON(!policy) in lock_policy_rwsem_read() if
      cpufreq_get() is called before registering a cpufreq driver.  Fix
      from Viresh Kumar.

   2) If intel_pstate has been loaded already, it doesn't make sense to
      do anything in acpi_cpufreq_init() and moreover doing something in
      there in that case may be harmful, so make that function return
      immediately if another cpufreq driver is already present.  From
      Yinghai Lu.

   3) The ACPI IPMI driver sometimes attempts to acquire a mutex from
      interrupt context, which can be avoided by replacing that mutex
      with a spinlock.  From Lv Zheng.

   4) A NULL pointer may be dereferenced by the exynos5440 cpufreq
      driver if a memory allocation made by it fails.  Fix from Sachin
      Kamat.

   5) Hanjun Guo's commit fixes a typo in the kerneldoc comment
      documenting acpi_bus_unregister_driver()"

* tag 'pm+acpi-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / scan: fix typo in comments of acpi_bus_unregister_driver()
  cpufreq: exynos5440: Fix potential NULL pointer dereference
  cpufreq: check cpufreq driver is valid and cpufreq isn't disabled in cpufreq_get()
  acpi-cpufreq: skip loading acpi_cpufreq after intel_pstate
  ACPI / IPMI: Fix atomic context requirement of ipmi_msg_handler()

Ben Herrenschmidt found that commit 928bea96 ("PCI: Delay enabling
bridges until they're needed") breaks PCI in some powerpc environments.

The reason is that the PCIe port driver will call pci_enable_device() on
the bridge, so the device is enabled, but skips pci_set_master because
pcie_port_auto and no acpi on powerpc.

Because of that, pci_enable_bridge() later on (called as a result of the
child device driver doing pci_enable_device) will see the bridge as
already enabled and will not call pci_set_master() on it.

Fixed by add checking in pci_enable_bridge, and call pci_set_master
if driver skip that.

That will make the code more robot and wade off problem for missing
pci_set_master in drivers.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull s390 lockref enablement from Heiko Carstens:
 "Enabling the new lockless lockref variant on s390 would have been
  trivial until Tony Luck added a cpu_relax() call into the
  CMPXCHG_LOOP(), with commit d472d9d9 ("lockref: Relax in cmpxchg
  loop")

  As already mentioned cpu_relax() is very expensive on s390 since it
  yields() the current virtual cpu.  So we are talking of several
  thousand cycles.  Considering this enabling the lockless lockref
  variant would contradict the intention of the new semantics.  And also
  some quick measurements show performance regressions of 50% and more.

  Simply removing the cpu_relax() call again seems also not very
  desireable since Waiman Long reported that for some workloads the call
  improved performance by 5%."

* 'lockref' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: enable ARCH_USE_CMPXCHG_LOCKREF
  lockref: use arch_mutex_cpu_relax() in CMPXCHG_LOOP()
  mutex: replace CONFIG_HAVE_ARCH_MUTEX_CPU_RELAX with simple ifdef

Commit 6072ddc8 ("kernel: replace strict_strto*() with kstrto*()")
broke the handling of signed integer types, fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull DeviceTree fixes from Rob Herring:
 "Clean-up to fix some warnings for !OF builds and spelling fixes in
  docs:

   - Clean-up openrisc prom.h
   - Fix warnings caused by of_irq.h ifdefs
   - Spelling fix for Synopsys"

* tag 'devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dts: Fix misspelling of Synopsys
  of: clean-up ifdefs in of_irq.h
  openrisc: clean-up prom.h

Pull ARM fixes from Russell King:
 "Just a few relatively small ARM fixes found since the last merge
  window, nothing too exciting"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7837/3: fix Thumb-2 bug in AES assembler code
  ARM: only allow kernel mode neon with AEABI
  ARM: 7839/1: entry: fix tracing of ARM-private syscalls
  ARM: 7836/1: add __get_user_unaligned/__put_user_unaligned