Add defines to make more human readable numbers for the lpass
clock controller found on IPQ806x SoCs. Also remove the PLL4
define in gcc to avoid #define conflicts because that clock
doesn't exist in gcc, instead it lives in lcc.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Split off into separate patch]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Add support for muxes that use regmap instead of readl/writel
directly. We don't support as many features as clk-mux.c, but
this is good enough to support getting and setting parents.
Adding a table based lookup can be added in the future if needed.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Add support for dividers that use regmap instead of readl/writel.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Switch to using generic divider code, drop
enable/disable, reword commit text]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Some devices don't use mmio to interact with dividers. Split out the
logic from the register read/write parts so that we can reuse the
division logic elsewhere.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Some clock drivers want to find the closest rate on the input of
a mux instead of a rate that's less than or equal to the desired
rate. Add a generic mux function to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Some of the clks can be registered & unregistered before the clk related debugfs
entries are initialized at late_initcall. In the unregister path checking for only
dentry before clk_debug_init() would lead dangling pointers in the debug clk list,
because the list is already populated in register path and the clk pointer freed in
unregister path.
The side effect of not removing it from the list is either a null pointer
dereference or if lucky to boot the system, the number of clk entries in
debugfs disappear.

We could add more checks like if (inited && !clk->dentry) but just removing
the check for dentry made more sense as debugfs_remove_recursive() seems to be
safe with null pointers. This will ensure that the unregistering clk would be
removed from the debug list in all the code paths.

Without this patch kernel would crash with log:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0204000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G    B          3.19.0-rc3-00007-g412f9ba-dirty #840
Hardware name: Qualcomm (Flattened Device Tree)
task: ed948000 ti: ed944000 task.ti: ed944000
PC is at strlen+0xc/0x40
LR is at __create_file+0x64/0x1dc
pc : [<c04ee604>]    lr : [<c049f1c4>]    psr: 60000013
sp : ed945e40  ip : ed945e50  fp : ed945e4c
r10: 00000000  r9 : c1006094  r8 : 00000000
r7 : 000041ed  r6 : 00000000  r5 : ed4af998  r4 : c11b5e28
r3 : 00000000  r2 : ed945e38  r1 : a0000013  r0 : 00000000
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c5787d  Table: 8020406a  DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xed944248)
Stack: (0xed945e40 to 0xed946000)
5e40: ed945e7c ed945e50 c049f1c4 c04ee604 c0fc2fa4 00000000 ecb748c0 c11c2b80
5e60: c0beec04 0000011c c0fc2fa4 00000000 ed945e94 ed945e80 c049f3e0 c049f16c
5e80: 00000000 00000000 ed945eac ed945e98 c08cbc50 c049f3c0 ecb748c0 c11c2b80
5ea0: ed945ed4 ed945eb0 c0fc3080 c08cbc30 c0beec04 c107e1d8 ecdf0600 c107e1d8
5ec0: c107e1d8 ecdf0600 ed945f54 ed945ed8 c0208ed4 c0fc2fb0 c026a784 c04ee628
5ee0: ed945f0c ed945ef0 c0f5d600 c04ee604 c0f5d5ec ef7fcc7d c0b40ecc 0000011c
5f00: ed945f54 ed945f10 c026a994 c0f5d5f8 c04ecc00 00000007 ef7fcc95 00000007
5f20: c0e90744 c0dd0884 ed945f54 c106cde0 00000007 c117f8c0 0000011c c0f5d5ec
5f40: c1006094 c100609c ed945f94 ed945f58 c0f5de34 c0208e50 00000007 00000007
5f60: c0f5d5ec be9b5ae0 00000000 c117f8c0 c0af1680 00000000 00000000 00000000
5f80: 00000000 00000000 ed945fac ed945f98 c0af169c c0f5dd2c ed944000 00000000
5fa0: 00000000 ed945fb0 c020f298 c0af168c 00000000 00000000 00000000 00000000
5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ebcc6d33 bfffca73
[<c04ee604>] (strlen) from [<c049f1c4>] (__create_file+0x64/0x1dc)
[<c049f1c4>] (__create_file) from [<c049f3e0>] (debugfs_create_dir+0x2c/0x34)
[<c049f3e0>] (debugfs_create_dir) from [<c08cbc50>] (clk_debug_create_one+0x2c/0x16c)
[<c08cbc50>] (clk_debug_create_one) from [<c0fc3080>] (clk_debug_init+0xdc/0x144)
[<c0fc3080>] (clk_debug_init) from [<c0208ed4>] (do_one_initcall+0x90/0x1e0)
[<c0208ed4>] (do_one_initcall) from [<c0f5de34>] (kernel_init_freeable+0x114/0x1e0)
[<c0f5de34>] (kernel_init_freeable) from [<c0af169c>] (kernel_init+0x1c/0xfc)
[<c0af169c>] (kernel_init) from [<c020f298>] (ret_from_fork+0x14/0x3c)
Code: c0b40ecc e1a0c00d e92dd800 e24cb004 (e5d02000)
---[ end trace b940e45b5e25c1e7 ]---

Fixes: 6314b679 "clk: Don't hold prepare_lock across debugfs creation"
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Merge branch 'clk-shmobile-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next

This new function is similar to clk_set_parent(), except that it doesn't
actually change the parent. It merely checks that the given parent clock
can be a parent for the given clock.

A situation where this is useful is to check that a particular setup is
valid before switching to it. One specific use-case for this is atomic
modesetting in the DRM framework where setting a mode is divided into a
check phase where a given configuration is validated before applying
changes to the hardware.

Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Provide CLK support for Alphascale ASM9260 SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Debugging eMMC on upstream kernels it has been noticed that when the
targetpack configures MMC0 clock to 200Mhz (required to switch to
HS200) then everything works OK. However if the kernel sets the
clock rate using clk_set_rate, then the eMMC card initialisation
fails with timeouts. Lower clock speeds (the default being 50Mhz)
work ok, but they we fail to get good eMMC transfer rates.

Looking through the vendor kernel clock driver reveals Giuseppe
had already fixed this issue, but the patch hasn't made its way
upstream.

The issue is fixed by changing the logic to manage the pdiv and
fdiv divisors used for setting the rate inside the flexgen driver code.

Pdiv is mainly targeted for low freq results, while fdiv should be
used for divs =< 64. The other way can lead to 'duty cycle'
issues.

I have changed the original patch to keep the original behaviour
in cases where the div is >64 which matches the original comment
and patch description more closely. Although no clocks appear to hit
this case currently when booting an upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Freescale introduced new ARM-based socs which using the compatible
clock IP block with PowerPC-based socs'. So this driver can be used
on both platforms.
Updated relevant descriptions and renamed this driver to better
represent its meaning and keep the function of driver untouched.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

redefine variable clocks_per_pll as a struct member

If there are multiple PLL clock nodes, this variable will
get overwritten. Redefining it as a struct member can avoid that.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

- Clock definitions for Exynos7 SoC peripheral devices:
  video scaler, USB, DMA, SPI and the audio subsystem.

The clocks on ti81xx are not compatible with omap3. On dm816x
the clock source is a FAPLL (Flying Adder PLL), and on dm814x
there seems to be an APLL (All Digital PLL).

Let's fix up things for dm816x in preparation for adding the
FAPLL support. As we already have a dummy ti81xx_dt_clk_init()
in place, let's use that for now to avoid adding a dependency
to the omap patches.

Later on if somebody adds dm814x support we can split the
ti81xx_dt_clk_init() clock init function as needed.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

On dm816x the clocks are sourced from a FAPLL (Flying Adder PLL)
that does not seem to be used on the other omap variants.

There are four instances of the FAPLL on dm816x that each have three
to seven child synthesizers.

I've set up the FAPLL as a single fapll.c driver. Later on we could
potentially have the PLL code generic. To do that, we would have to
consider the following:

1. Setting the PLL to bypass mode also sets the child synthesizers
   into bypass mode. As the bypass rate can also be generated by
   the PLL in regular mode, there's no way for the child synthesizers
   to detect the bypass mode based on the parent clock rate.

2. The PLL registers control the power for each of the child
   syntheriser.

Note that the clocks are currently still missing the set_rate
implementation so things are still running based on the bootloader
values. That's OK for now as most of the outputs have dividers and
those can be set using the existing TI component clock code.

I have verified that the extclk rates are correct for a few clocks,
so adding the set_rate support should be fairly trivial later on.

This code is partially based on the TI81XX-LINUX-PSP-04.04.00.02
patches published at:

http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

We don't need to fetch the parent index for clocks if they only
have one parent. Doing this also avoid an unnecessary allocation
for the parent cache.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit #
should be no higher than 15, however the corresponding check is obviously off-
by-one.

Fixes: 04577994 ("clk: gate: add CLK_GATE_HIWORD_MASK")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

In order to fix the following section mismatch warning:
  WARNING: drivers/clk/built-in.o(.data+0xe4): Section mismatch in reference from the variable ppc_corenet_clk_driver to the function .init.text:ppc_corenet_clk_probe()
  The variable ppc_corenet_clk_driver references
  the function __init ppc_corenet_clk_probe()
  If the reference is valid then annotate the
  variable with __init* or __refdata (see linux/init.h) or name the variable:
  *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console

  WARNING: drivers/clk/built-in.o(.data+0x10c): Section mismatch in reference from the variable ppc_corenet_clk_driver to the variable .init.rodata:ppc_clk_ids
  The variable ppc_corenet_clk_driver references
  the variable __initconst ppc_clk_ids
  If the reference is valid then annotate the
  variable with __init* or __refdata (see linux/init.h) or name the variable:
  *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console

We can't just add the __init annotation to ppc_corenet_clk_driver or
remove the __init from ppc_corenet_clk_probe() and ppc_clk_ids.
So choose to use CLK_OF_DECLARE to scan and init the clock devices.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

So the boards which has COMMON_CLK enabled don't have to
invoke this in its board specific file.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

The memory allocated by basic clock divider/gate/mux (struct clk_gate,
clk_divider and clk_mux) was leaking. During driver unbind or probe
failure the driver only unregistered the clocks.

Use clk_unregister_{gate,divider,mux} to release all resources.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

The common clk_register_{divider,gate,mux} functions allocated memory
for internal data which wasn't freed anywhere. Drivers using these
helpers could only unregister clocks but the memory would still leak.

Add corresponding unregister functions which will release all resources.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

The driver allows using CDCE706 in its default configuration recorded in
EEPROM and adjusting of synthesized clocks by consumers.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

The commit 646cafc6 (clk: Change clk_ops->determine_rate to
return a clk_hw as the best parent) opens a possibility for
null pointer dereference, fix this.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

This reverts commit da788acb.

That commit tried to fix the section mismatch warning by moving the
ppc_corenet_clk_driver struct to init section. This is definitely wrong
because the kernel would free the memories occupied by this struct
after boot while this driver is still registered in the driver core.
The kernel would panic when accessing this driver struct.

Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Lockdep reported a possible deadlock between the cpuclk lock and for example
the i2c driver.

       CPU0                    CPU1
       ----                    ----
  lock(clk_lock);
                               local_irq_disable();
                               lock(&(&i2c->lock)->rlock);
                               lock(clk_lock);
  <Interrupt>
    lock(&(&i2c->lock)->rlock);

 *** DEADLOCK ***

The generic clock-types of the core ccf already use spin_lock_irqsave when
touching clock registers, so do the same for the cpuclk.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: removed initialization of "flags"]

Add required clk support for I2S, PCM and SPDIF.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>

Add clock support for 5 SPI channels.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>

Add support for PDMA0 and PDMA1 gate clks.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>

The "smemc" clock is removed on BG2Q SoCs. In fact, bit19 of clkenable
register is for nfc. Current code use bit19 for non-exist "smemc"
incorrectly, this prevents eMMC from working due to the sdhci's
"core" clk is still gated.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Michael Turquette <mturquette@linaro.org>

All slow clk users are not properly claiming it (get + prepare + enable)
before using it.
If all users properly claiming this clock release it, the clock is
disabled, but faulty users still depends on it, and the system hangs.

This fix prevents the slow clock from being disabled, and should solve the
hanging issue, but offending drivers should be patched to properly claim
this clock.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Bo Shen <voice.shen@atmel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Merge tag 'v3.19-rockhip-clkfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-fixes

- two currently unused clocks that need to stay enabled
- fix the lock bit locations of the rk3066 plls
- fix rk3288 core divider values to the ones actually
  specified by the soc vendor

Add the ADSP clock support to the R-Car generation 2 CPG driver.  This clock
gets derived from  PLL1.  The layout of the ADSPCKCR register is  similar to
those of the clocks supported by the 'clk-div6' driver but the divider encoding
is non-linear, so can't be supported by that driver...

Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add the RCAN clock support to the R-Car generation 2 CPG driver.  This clock
gets derived from  the USB_EXTAL clock, dividing  it by 6.  The layout of the
RCANCKCR register is similar to those of the clocks supported by the 'clk-div6'
driver but has no divider field, and so can't be supported by that driver...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Driver for the R8A73A4's clocks that are too specific to be supported by a
generic driver.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

R-Car M2N (r8a7793) clock is handled in R-Car Gen2 clock driver.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

While DIV6 clocks require the divisor field to be non-zero when stopping
the clock, some clocks (e.g. ZB on sh73a0) fail to be re-enabled later
if the divisor field is changed when stopping the clock.
The reason for this is unknown.

To fix this, do not touch the divisor field if it's already non-zero.

On kzm9g, the smsc911x Ethernet controller is connected to the sh73a0
Bus State Controller, which is clocked by the ZB clock. Without this
fix, if the ZB clock is disabled during system suspend, and re-enabled
during resume, the kernel locks up when the smsc911x driver tries to
access the Ethernet registers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Commit 0e5bdb3f (clk: rockchip: switch to using the new cpuclk type
for armclk) didn't take into account that the divider used on rk3288
are of the (n+1) type.

The rk3066 and rk3188 socs use more complex divider types making it
necessary for the list-elements to be the real register-values to write.

Therefore reduce divider values in the table accordingly so that they
really are the values that should be written to the registers and match
the dividers actually specified for the rk3288.
Reported-by: Sonny Rao <sonnyrao@chromium.org>
Fixes: 0e5bdb3f ("clk: rockchip: switch to using the new cpuclk type for armclk")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org