Merge tag 'samsung-soc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc

Samsung Exynos (and older platforms) improvements for v4.6:
1. Split out Exynos PMU driver implementation from arm/mach-exynos
   to the drivers/soc/samsung which will allow re-use of it on ARM64.
2. Use generic DT cpufreq driver on Exynos542x/5800.
3. Minor cleanups.

* tag 'samsung-soc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: s3c24xx: Avoid warning for inb/outb
  ARM: SAMSUNG: Remove unused register offset definition
  ARM: EXYNOS: Cleanup header files inclusion
  drivers: soc: samsung: Enable COMPILE_TEST
  MAINTAINERS: Add maintainers entry for drivers/soc/samsung
  drivers: soc: Add support for Exynos PMU driver
  ARM: EXYNOS: Split up exynos5420 SoC specific PMU data
  ARM: EXYNOS: Split up exynos5250 SoC specific PMU data
  ARM: EXYNOS: Split up exynos4 SoC specific PMU data
  ARM: EXYNOS: Split up exynos3250 SoC specific PMU data
  ARM: EXYNOS: Move pmu specific headers under "linux/soc/samsung"
  ARM: EXYNOS: Correct header comment in Kconfig file
  ARM: EXYNOS: Use generic cpufreq driver for Exynos5422/5800
  ARM: EXYNOS: Use generic cpufreq driver for Exynos5420
  ARM: s3c64xx: use "depends on" instead of "if" after prompt
  ARM: plat-samsung: use to_platform_device()
  ARM: EXYNOS: Code cleanup in map.h
  ARM: EXYNOS: Remove unused static mapping of CMU for exynos5
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'stm32-soc-for-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32 into next/soc

Merge "STM32 SoC updates for v4.6 #2" from Maxime Coquelin:

Highlights:
-----------
 - Add a new stm32f469 SoC

* tag 'stm32-soc-for-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32:
  ARM: stm32: Identify a new SoC - STM32F469

Merge tag 'omap-for-v4.6/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc

Merge "omap soc changes for v4.6 merge window" from Tony Lindgren:

SoC related changes for omaps for v4.6 merge window:

- Enable runtime revision detection for dra7 to avoid multiple dts
  files for various variants

- Add dma_slave_map for omap1/2/3 legacy mode booting

- Add RTC interconnect target data for ti81xx and am43x

- Add custom reset handler for PCIeSS

- Add eDMA interconnect target data for dra7

* tag 'omap-for-v4.6/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
  ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
  ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
  ARM: OMAP2+: DMA: Provide dma_slave_map to omap-dma for legacy boot
  ARM: OMAP1: DMA: Provide dma_slave_map to omap-dma
  ARM: OMAP: DRA7: Make use of omap_revision information for soc_is* calls
  ARM: AM43XX: hwmod: Add rtc hwmod
  ARM: DRA7: hwmod: Add reset data for PCIe
  ARM: DRA7: hwmod: Fix OCP2SCP sysconfig
  ARM: OMAP2+: hwmod data: Add SSI data for omap36xx

Merge tag 'imx-soc-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc

Merge "i.MX SoC update for 4.6" from Shawn Guo:

- Enable big endian mode support for i.MX platform
- Add support for i.MX6QP SoC which is the latest i.MX6 family addition
- Add basic suspend/resume support for i.MX25
- A couple of i.MX7D support updates
- A few random code cleanups

* tag 'imx-soc-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx: Make reset_control_ops const
  ARM: imx: Do L2 errata only if the L2 cache isn't enabled
  ARM: imx: select ARM_CPU_SUSPEND only for imx6
  ARM: mx25: Add basic suspend/resume support
  ARM: imx: Add msl code support for imx6qp
  ARM: imx: enable big endian mode
  ARM: imx: use endian-safe readl/readw/writel/writew
  ARM: imx7d: correct chip version information
  ARM: imx: select HAVE_ARM_ARCH_TIMER if selected i.MX7D
  ARM: imx6: fix cleanup path in imx6q_suspend_init()

In an invalid randconfig build (fixed by another patch),
I ran across this warning:

arch/arm/include/debug/at91.S:18:0: error: "CONFIG_DEBUG_UART_VIRT" redefined [-Werror]
 #define CONFIG_DEBUG_UART_VIRT AT91_IO_P2V(CONFIG_DEBUG_UART_PHYS)

As Russell pointed out, we should never #define a macro starting
with CONFIG_ in a source file, as that is rather confusing.

This renames the macro to avoid the symbol clash.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Merge tag 'for-v4.6/omap-hwmod-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/soc

ARM: OMAP2+: second set of hwmod changes for v4.6

These patches add RTC support for the AM43xx, and add support for
the DRA7xx eDMA controller's TPCC, TPTC0, and TPTC1 IP blocks.
Also included is a workaround for PRCM hardreset control of the DRA7xx
PCIe subsystem.

Note that I do not have a DRA7xx board, and therefore cannot
test any patches for that SoC family.

Basic build, boot, and PM test logs can be found here:

http://www.pwsan.com/omap/testlogs/omap-hwmod-b-for-v4.6/20160301021258/

Add hwmod data for the eDMA blocks:
 - TPCC: Third-party channel controller
 - TPTC0: Third-party transfer controller 0
 - TPTC1: Third-party transfer controller 1

The TPCC's clock gating status follows the status of its clock and
power domain. This means that the hwmod code can not directly control
the TPCC enable/disable status.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: rephrased last two sentences of the patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Merge "pxa changes for v4.6 cycle" from Robert Jarzmik:

This is a minor cycle with :
 - cleanup fixes from Arnd, mainly build oriented and sparse type ones
 - dma fixes for requestors above 32 (impacting mainly camera driver)
 - some minor cleanup on pxa3xx device-tree side

* tag 'pxa-for-4.6' of https://github.com/rjarzmik/linux:
  dmaengine: pxa_dma: fix the maximum requestor line
  ARM: pxa: add the number of DMA requestor lines
  dmaengine: mmp-pdma: add number of requestors
  dma: mmp_pdma: Add the #dma-requests DT property documentation
  ARM: pxa: pxa3xx device-tree support cleanup
  ARM: pxa: don't select RFKILL if CONFIG_NET is disabled
  ARM: pxa: fix building without IWMMXT
  ARM: pxa: move extern declarations to pm.h
  ARM: pxa: always select one of the two CPU types
  ARM: pxa: don't select GPIO_SYSFS for MIOA701
  ARM: pxa: mark unused eseries code as __maybe_unused
  ARM: pxa: mark spitz_card_pwr_ctrl as __maybe_unused
  ARM: pxa: define clock registers as __iomem

Merge tag 'sunxi-core-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/soc

Merge "Allwinner core changes for 4.6" from Maxime Ripard:

Just introduce the A83T support.

* tag 'sunxi-core-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: sunxi: Introduce Allwinner for A83T support

The imx_src_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All the generic L2 cache handling code is encapsulated by a
check if the L2 cache is enabled. If it's enabled already, the code
is skipped. The write to the L2-Cache controller from non-secure
world causes an imprecise external abort. This is needed in
scenarios where one of the cores runs an other OS, e.g. an RTOS.

For the i.MX6 specific L2 cache handling we missed this check.
Add it.
Signed-off-by: Marcel Grosshans <MarcelViktor.Grosshans@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX only needs to select ARM_CPU_SUSPEND manually for the
very specific case that CONFIG_PM_SLEEP is disabled and imx6
is used with CONFIG_PM enabled for runtime PM.

If we are building a kernel only for CPUs that are not using
the cpu_suspend() helper, we otherwise get a harmless
build warning:

warning: (ARCH_MXC && SOC_IMX23 && SOC_IMX28 && ARCH_PXA && MACH_MVEBU_V7 && ARCH_OMAP3 && ARCH_OMAP4 && SOC_OMAP5 && SOC_AM33XX && SOC_DRA7XX && ARCH_EXYNOS3 && ARCH_EXYNOS4 && EXYNOS5420_MCPM &&
EXYNOS_CPU_SUSPEND && ARCH_VEXPRESS_TC2_PM && ARM_BIG_LITTLE_CPUIDLE && ARM_HIGHBANK_CPUIDLE && QCOM_PM) selects ARM_CPU_SUSPEND which has unmet direct dependencies (ARCH_SUSPEND_POSSIBLE)

This moves the option to the SOC_IMX6 option that actually
requires it, in effect reverting commit f36b594f ("ARM:
mach-imx: Select ARM_CPU_SUSPEND at ARCH_MXC level") that was
meant as a cleanup and unintentionally caused this warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Merge "Broadcom maintainers changes for 4.6" from Florian Fainelli:

This pull request contains MAINTAINERS file updates for Broadcom ARM-based SoCs:

- Florian updates the Broadcom BCM63xx ARM-based DSL SoCs to use the same mailing-list
  and development tree as all the other Broadcom SoCS

* tag 'arm-soc/for-4.6/maintainers' of http://github.com/Broadcom/stblinux:
  MAINTAINERS: ARM: BCM63xx: Update git and mailing-lists

Merge "Broadcom soc changes for 4.6" from Florian Fainelli:

This pull request contains Broadcom ARM-based SoC/platform changes:

- Masahiro updates the Broadcom Northstar Plus SMP operations to be annotated
  with const and __initconst

- Florian removes an unused variable in the Broadcom BCM63XX SMP code

* tag 'arm-soc/for-4.6/soc' of http://github.com/Broadcom/stblinux:
  ARM: BCM63xx: Remove unused pmb_dn variable
  ARM: bcm: use const and __initconst for smp_operations

The current number of requestor lines is limited to 31. This was an
error of a previous commit, as this number is platform dependent, and is
actually :
 - for pxa25x: 40 requestor lines
 - for pxa27x: 75 requestor lines
 - for pxa3xx: 100 requestor lines

The previous testing did not reveal the faulty constant as on pxa[23]xx
platforms, only camera, MSL and USB are above requestor 32, and in these
only the camera has a driver using dma.

Fixes: e87ffbdf ("dmaengine: pxa_dma: fix the no-requestor case")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vinod Koul <vinod.koul@intel.com>

Select the Alpine MSI controller driver when using an Alpine platform.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Declare the number of DMA requestor lines per platform :
 - for pxa25x: 40 requestor lines
 - for pxa27x: 75 requestor lines
 - for pxa3xx: 100 requestor lines

This information will be used to activate the DMA flow control or not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

The DMA chip has a fixed number of requestor lines used for flow
control. This number is platform dependent. The pxa_dma dma driver will
use this value to activate or not the flow control.

There won't be any impact on mmp_pdma driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

For pxa based platforms, the number of requestor lines should be
specified, so that the driver can check if the flow control should be
activated (when a requestor line is asked for) or not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Rob Herring <robh@kernel.org>

Merge "ARM: Xilinx Zynq patches for v4.6" from Michal Simek:

- SLCR early init
- Fix L2 cache data corruption
- Fix early printk uart setting

* tag 'zynq-soc-for-4.6' of https://github.com/Xilinx/linux-xlnx:
  ARM: zynq: Move early printk virtual address to vmalloc area
  ARM: zynq: address L2 cache data corruption
  ARM: zynq: initialize slcr mapping earlier

Merge tag 'davinci-for-v4.6/edma' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc

Merge "DaVinci EDMA enhancements for v4.6" from Sekhar Nori:

Pass dma_slave_map data to EDMA driver. This will help
migration to new DMA engine API for requesting
slave channels dma_request_chan().

* tag 'davinci-for-v4.6/edma' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: davinci: dm646x: Add dma_slave_map to edma
  ARM: davinci: dm644x: Add dma_slave_map to edma
  ARM: davinci: dm365: Add dma_slave_map to edma
  ARM: davinci: dm355: Add dma_slave_map to edma
  ARM: davinci: devices-da8xx: Add dma_slave_map to edma

Merge tag 'renesas-soc-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

Merge "Renesas ARM Based SoC Updates for v4.6" from Simon Horman:

* Enable PM and PM_GENERIC_DOMAINS for SoCs with PM Domains
* Move emev2_smp_ops to emev2
* Remove legacy map_io callbacks on r8a7740 and emev2 SoCs
* Migrate to generic l2c OF initialization on r8a7740

* tag 'renesas-soc-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: Enable PM and PM_GENERIC_DOMAINS for SoCs with PM Domains
  ARM: shmobile: emev2: Move declaration of emev2_smp_ops to emev2.h
  ARM: shmobile: emev2: Remove legacy machine_desc.map_io() callback
  ARM: shmobile: r8a7740: Remove legacy machine_desc.map_io() callback
  ARM: shmobile: r8a7740: Remove mapping of L2 cache controller registers
  ARM: shmobile: r8a7740: Migrate to generic l2c OF initialization

Merge "ARM: mediatek: soc updates for v4.6" from Matthias Brugger:

Fix state machine implemenation of PMIC wrapper.
Add SMP support for mt7623.
Disable watchdog of STAUPD in PMIC wrapper for mt8173.
Add SMP support for mt2701.
Use builtin_platform_driver for scpsys. Driver can't be build as module.
Fix regulator enablement in scpsys.

* tag 'v4.5-next-soc' of https://github.com/mbgg/linux-mediatek:
  soc: mediatek: SCPSYS: Fix double enabling of regulators
  soc: mediatek: SCPSYS: use builtin_platform_driver
  ARM: mediatek: add mt2701 smp bringup code
  soc: mediatek: PMIC wrap: clear the STAUPD_TRIG bit of WDT_SRC_EN
  ARM: mediatek: add MT7623 smp bringup code
  soc: mediatek: PMIC wrap: Clear the vldclr if state machine stay on FSM_VLDCLR state.

This allows RTC to work properly with the related DTS
changes.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

s3c24xx implements its own inb/outb macros, but the implementation
prints warnings when the port number argument is not a 32-bit scalar:

drivers/scsi/pas16.c: In function 'NCR5380_pwrite':
arch/arm/mach-s3c24xx/include/mach/io.h:193:68: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
 #define __ioaddrc(port) ((__PORT_PCIO(port) ? PCIO_BASE + (port) : (void __iomem *)(port)))

This slightly modifies the definition of the __ioaddrc macro to avoid
the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

The patch
"ARM: 8432/1: move VMALLOC_END from 0xff000000 to 0xff800000"
(sha1: 6ff09660)
has moved also start of VMALLOC area because size didn't change.
That's why origin location of vmalloc was
   vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
and now is
   vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)

That's why uart virtual addresses need to be changed to reflect this new
memory setup. Starting address should be vmalloc start address.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>

Add a custom reset handler for DRA7x PCIeSS. This
handler is required to deassert PCIe hardreset lines
after they have been asserted.

This enables the PCIe driver to access registers after
PCIeSS has been runtime enabled without having to
deassert hardreset lines itself.

With this patch applied, used lspci to make sure
connected PCIe device enumerates on DRA74x and DRA72x
EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reported-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This patch cleans up various map.h under mach-exynos, mach-s3c24xx and
plat-samsung by removing unused register offset. This patch also does a
minor nitpick of changing EXYNOS4 to EXYNOS from comment section of
header file "mach-exynos/include/mach/map.h".
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This includes trivial cleanup in exynos files such as
 - remove unused header files inclusion from exynos.c, s5p-dev-mfc.c,
   firmware.c, pm.c.
 - move inclusion of of.h from common.h to pm.c where it is really
   required
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

Get some build coverage of Exynos PMU driver. It depends on
asm/cputype.h so its compilation is limited to ARM architectures.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>

This patch adds maintainers entry for new driver folder
drivers/soc/samsung
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch moves Exynos PMU driver implementation from "arm/mach-exynos"
to "drivers/soc/samsung". This driver is mainly used for setting misc
bits of register from PMU IP of Exynos SoC which will be required to
configure before Suspend/Resume. Currently all these settings are done
in "arch/arm/mach-exynos/pmu.c" but moving ahead for ARM64 based SoC
support, there is a need of this PMU driver in driver/* folder.

This driver uses existing DT binding information and there should
be no functionality change in the supported platforms.
Signed-off-by: Amit Daniel Kachhap <amitdanielk@gmail.com>
[tested on Peach-Pi (Exynos5880)]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[for testing on Trats2 (Exynos4412) and Odroid XU3 (Exynos5422)]
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[k.kozlowski: Rebased, add necessary infrastructure for building and
selecting drivers/soc because original patchset was on top of movement
SROMc to drivers/soc]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch splits up mach-exynos/pmu.c file, and moves exynos5420,
PMU configuration data and functions handing data into exynos5420
SoC specific PMU file mach-exynos/exynos5420-pmu.c.

[tested on Peach-Pi (Exynos5880)]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch splits up mach-exynos/pmu.c file, and moves exynos5250,
PMU configuration data and functions handing data into exynos5250
SoC specific PMU file mach-exynos/exynos5250-pmu.c.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch splits up mach-exynos/pmu.c file, and moves exynos4210,
exynos4412 and exynos4212 PMU configuration data and functions handing
data into a common exynos4 SoC specific PMU file mach-exynos/exynos4-pmu.c.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[for testing on Trats2 (Exynos4412, S2R, reboot, poweroff)]
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch splits up mach-exynos/pmu.c file, and moves exynos3250 PMU
configuration data and functions handing those data into exynos3250
SoC specific PMU file mach-exynos/exynos3250-pmu.c.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

Moving Exynos PMU specific header file into "include/linux/soc/samsung"
thus updated affected files under "mach-exynos" to use new location of
these header files.
Signed-off-by: Amit Daniel Kachhap <amitdanielk@gmail.com>
[tested on Peach-Pi (Exynos5880)]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[for testing on Trats2 (Exynos4412) and Odroid XU3 (Exynos5422)]
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch corrects header comment of Kconfig file by changing EXYNOS4 to
EXYNOS.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

The new CPU clock type allows the use of generic cpufreq-dt driver
for Exynos5422/5800.

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

The new CPU clock type allows the use of cpufreq-dt driver
for Exynos5420.

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>