rtl8169_mark_as_last_descriptor() has just one user, so inline it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2020-04-19

This series contains updates to e1000e and igc only.

Sasha adds new device IDs supported by the igc driver.

Vitaly fixes the S0ix entry and exit flows in e1000e for TGP and newer
MAC types when a cable is connected.

Andre has the remaining changes in the series, starting with cleanup of
the igc driver of duplicate code.  Added a check for
IGC_MAC_STATE_SRC_ADDR flag which is unsupported for MAC filters in igc.
Cleaned up the return values for igc_add_mac_filter(), where the return
value was not being used, so update the function to only return success
or failure.  Fix the return value of igc_uc_unsync() as well.  Refactor
the igc driver in several functions to help reduce the convoluted logic
and simplify the driver filtering mechanisms.  Improve the MAC address
checks when adding a MAC filter.  Lastly, improve the log messages
related to MAC address filtering to ease debugging.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove casting the values returned by memory allocation function.

Coccinelle emits WARNING: casting value returned by memory allocation
function to struct pointer is useless.

This issue was detected by using the Coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove casting the values returned by memory allocation function.

Coccinelle emits WARNING: casting value returned by memory allocation
function to (struct cas_init_block *) is useless.

This issue was detected by using the Coccinelle software.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add PMTU discovery tests for these encapsulations:

- IPIP
- SIT, mode ip6ip
- ip6tnl, modes ip6ip6 and ipip6
Signed-off-by: Lourdes Pedrajas <lu@pplo.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't use internal knowledge of the mdio bus core, instead use
mdiobus_get_phy() which does the same thing.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Two small changes

Patch #1 increases the scale of supported IPv6 nexthops groups when each
group has one nexthop and all are using the same nexthop device, but
with a different gateway IP.

Patch #2 adjusts a register definition in accordance with recent
firmware changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The Infrastructure Entry Delete Register (IEDR) is used to delete
entries stored in the KVD linear database. Currently, it is only
possible to delete entries of size up to 2048. Future firmware versions
will support deletion of entries of size up to 4096.

Increase the size of the field so that the driver will be able to
perform such deletions in the future, when required.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As explained in commit fc25996e ("mlxsw: spectrum_router: Increase
scale of IPv6 nexthop groups"), each nexthop group is hashed by XOR-ing
the interface indexes of all the member nexthop devices.

To avoid many different nexthop groups ending up using the same key, the
above commit started hashing the interface indexes themselves before
they are XOR-ed.

However, in cases in which there are many nexthop groups that all use
the same nexthop device and only differ in the gateway IP, we can still
end up in a situation in which all the groups are using the same key.
This eventually leads to -EBUSY error from rhashtable during insertion.

Improve the situation by also making the gateway IP part of the key.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a bus->reset() call for the mii_bus structure returns an error (e.g.:
-EPROE_DEFER) we should propagate it accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: realtek: move PHY resume delay from MAC to PHY driver

Internal PHY's from RTL8168h up may not be instantly ready after calling
genphy_resume(). So far r8169 network driver adds the needed delay, but
better handle this in the PHY driver. The network driver may miss other
places where the PHY is resumed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The Realtek PHY driver takes care of adding the needed delay now,
therefore we can remove the delay here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Internal PHY's from RTL8168h up may not be instantly ready after calling
genphy_resume(). So far r8169 network driver adds the needed delay, but
better handle this in the PHY driver. The network driver may miss other
places where the PHY is resumed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following coccicheck warning:

drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:700:2-8: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:702:2-8: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warnings:

drivers/ptp/ptp_idt82p33.c:26:5: warning: symbol 'sync_tod_timeout' was not declared. Should it be static?
drivers/ptp/ptp_idt82p33.c:31:5: warning: symbol 'phase_snap_threshold' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/ptp/ptp_kvm.c:25:1: warning:
 symbol 'kvm_ptp_lock' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some boards do not have the RX_ER MII signal connected. Normally in such
situation, those pins would be grounded, but then again, some boards
left it electrically floating.

When sending traffic to those switch ports, one can see that the
N_SOFERR statistics counter is incrementing once per each packet. The
user manual states for this counter that it may count the number of
frames "that have the MII error input being asserted prior to or
up to the SOF delimiter byte". So the switch MAC is sampling an
electrically floating signal, and preventing proper traffic reception
because of that.

As a workaround, enable the internal weak pull-downs on the input pads
for the MII control signals. This way, a floating signal would be
internally tied to ground.

The logic levels of signals which _are_ externally driven should not be
bothered by this 40-50 KOhm internal resistor. So it is not an issue to
enable the internal pull-down unconditionally, irrespective of PHY
interface type (MII, RMII, RGMII, SGMII) and of board layout.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds log messages to functions related to the MAC address
filtering code to ease debugging.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does a code refactoring in igc_del_mac_filter() so it uses
the new helper igc_find_mac_filter() and improves the comment about the
special handling when deleting the default filter.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The helper igc_mac_entry_can_be_used() implementation is a bit
convoluted since it does two different things: find a not-in-use slot
in mac_table or find an in-use slot where the address and address type
match. This patch does a code refactoring and break it up into two
helper functions.

With this patch we might traverse mac_table twice in some situations,
but this is not harmful performance-wise (mac_table has only 16 entries
and adding mac filters is not hot-path), and it improves igc_add_mac_
filter() readability considerably.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

With the previous two patches, igc_add_mac_steering_filter() and
igc_del_mac_steering_filter() became a pointless wrapper of
igc_add_mac_filter() and igc_del_mac_filter().

This patch removes these wrappers and update callers to call
igc_add_mac_filter() and igc_del_mac_filter() directly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The IGC_MAC_STATE_QUEUE_STEERING bit in mac_table[i].state is
utilized to indicate that frames matching the filter are assigned to
mac_table[i].queue. This bit is not strictly necessary since we can
convey the same information as follows: queue == -1 means queue
assignment is disabled, otherwise it is enabled.

In addition to make the code simpler, this change fixes some awkward
situations where we pass a complete misleading 'queue' value such as in
igc_uc_sync().

So this patch removes IGC_MAC_STATE_QUEUE_STEERING and also takes the
opportunity to improve the igc_add_mac_filter documentation.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igc_add_mac_filter() doesn't allow us to have more than one entry with
the same address and address type in adapter->mac_table so checking if
'queue' matches in igc_del_mac_filter() isn't necessary. This patch
removes that check.

This patch also takes the opportunity to improve the igc_del_mac_filter
documentation and remove comment which is not applicable to this I225
controller.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

igc_add_mac_filter() doesn't allow filters with invalid MAC address to
be added to adapter->mac_table so, in igc_del_mac_filter(), we can early
return if MAC address is invalid. No need to traverse the table.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Current igc_rar_set_index() implementation is a bit convoluted so this
patch does some code refactoring to improve it.

The helper igc_rar_set_index() is about writing MAC filter settings into
hardware registers. Logic such as address validation belongs to
functions upper in the call chain such as igc_set_mac() and
igc_add_mac_filter(). So this patch moves the is_valid_ether_addr() call
to igc_add_mac_filter(). No need to touch igc_set_mac() since it already
checks it.

The variables 'rar_low' and 'rar_high' represent the value in registers
RAL and RAH so we rename them to 'ral' and 'rah', respectively, to
match the registers names.

To make it explicit, filter settings are passed as arguments to the
function instead of reading them from adapter->mac_table "under the
hood". Also, the function was renamed to igc_set_mac_filter_hw to make
it more clear what it does.

Finally, the patch removes some wrfl() calls and comments not needed.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In case igc_del_mac_filter() returns error, that error is masked
since the functions always return 0 (success). This patch fixes
igc_uc_unsync() so it returns whatever value igc_del_mac_filter()
returns (0 on success, negative number on error).
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In case of success, igc_add_mac_filter() returns the index in
adapter->mac_table where the requested filter was added. This
information, however, is not used by any caller of that function.
In fact, callers have extra code just to handle this returning
index as 0 (success).

So this patch changes the function to return 0 on success instead,
and cleans up the extra code.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The IGC_MAC_STATE_SRC_ADDR flags is not supported by igc_add_mac_
filter() so this patch adds a check for it and returns -ENOTSUPP
in case it is set.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does a code refactoring in the MAC address filtering logic to
get rid of some duplicate code.

IGC driver has two functions to add MAC address filters that are pretty
much the same: igc_add_mac_filter() and igc_add_mac_filter_flags(). The
only difference is that the latter allows the callee to specify the
'flags' parameter while the former has it hard coded as zero. The same
rationale applies to filter deletion counterparts.

So this patch refactors igc_add_mac_filter() and igc_del_mac_filter() so
they handle the 'flags' parameters, removes the _flags() functions, and
fixes callees accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Added a fix to S0ix entry and exit flows for TGP and above
MAC types, to the case when the Ethernet cable is connected
and the link is up. With that the system is able to reach
SLP_S0 when going to freeze power state.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add new device IDs for the next step of i225
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Heiner Kallweit says:

====================
r8169: series with improvements

Again a series with few improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add workaround for hw issues with TSO on RTL8168evl. This workaround is
based on information I got from Realtek, and *should* allow to safely
enable TSO on this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the code and avoid the overhead of calling vlan_get_protocol().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At that place in rtl_init_one() we can safely use rtl8169_set_features()
to configure the chip according to the default features.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far we set RX_VLAN_8125 unconditionally, even if
NETIF_F_HW_VLAN_CTAG_RX may not be set. Don't touch these bits,
and let only rtl8169_set_features() control them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NETIF_F_HIGHDMA is added to vlan_features by register_netdev(),
therefore we can omit this here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move setting the ocp_base to rtl_init_one(). Where supported the value
is always the same, and if not supported it doesn't hurt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each ENETC station interface (SI) has a VLAN filter list and a port
flag (PSIPVMR) by which it can be put in "VLAN promiscuous" mode, which
enables the reception of VLAN-tagged traffic even if it is not in the
VLAN filtering list.

Currently the handling of this setting works like this: the port starts
off as VLAN promiscuous, then it switches to enabling VLAN filtering as
soon as the first VLAN is installed in its filter via
.ndo_vlan_rx_add_vid. In practice that does not work out very well,
because more often than not, the first VLAN to be installed is out of
the control of the user: the 8021q module, if loaded, adds its rule for
802.1p (VID 0) traffic upon bringing the interface up.

What the user is currently seeing in ethtool is this:
ethtool -k eno2
rx-vlan-filter: on [fixed]

which doesn't match the intention of the code, but the practical reality
of having the 8021q module install its VID which has the side-effect of
turning on VLAN filtering in this driver. All in all, a slightly
confusing experience.

So instead of letting this driver switch the VLAN filtering state by
itself, just wire it up with the rx-vlan-filter feature from ethtool,
and let it be user-configurable just through that knob, except for one
case, see below.

In promiscuous mode, it is more intuitive that all traffic is received,
including VLAN tagged traffic. It appears that it is necessary to set
the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is
also temporarily enabled. On exit from promiscuous mode, the setting
made by ethtool is restored.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>