From: Yinghai Lu <yinghai@kernel.org>

Allocate resources to SRIOV BARs only after all other required
resource-requests are satisfied. Dont retry if resource allocation for SRIOV
BARs fail.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Currently pci-bridges are allocated enough resources to satisfy their immediate
requirements.  Any additional resource-requests fail if additional free space,
contiguous to the one already allocated, is not available. This behavior is not
reasonable since sufficient contiguous resources, that can satisfy the request,
are available at a different location.

This patch provides the ability to expand and relocate a allocated resource.

	v2: Changelog: Fixed size calculation in pci_reassign_resource()
	v3: Changelog : Split this patch. The resource.c changes are already
			upstream. All the pci driver changes are in here.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

git commit c8adf9a3
    "PCI: pre-allocate additional resources to devices only after
	successful allocation of essential resources."

fails to take into consideration the optional-resources needed by children
devices while calculating the optional-resource needed by the bridge.

This can be a problem on some setup. For example, if a hotplug bridge has 8
children hotplug bridges, the bridge should have enough resources to accomodate
the hotplug requirements for each of its children hotplug bridges.  Currently
this is not the case.

This patch fixes the problem.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size.  There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device.  However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.

This can be achieved two ways:

- A conservative approach is to use the smallest common denominator of
  the entire tree below a root complex for every device on that fabric.

This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.

It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.

- A more optimal way is possible, if it falls within a couple of
  constraints:
* The top-level host bridge will never generate packets larger than the
  smallest TLP (or if it can be controlled independently from its MPS at
  least)
* The device will never generate packets larger than MPS (which can be
  configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
  some additional code to specifically deal with that case

Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.

In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.

To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls.  "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.

NOTE: due to the location of the enablement, each arch will need to add
calls to this function.  This patch only enables x86.

This patch includes a number of changes recommended by Benjamin
Herrenschmidt.

Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  CIFS: Cleanup demupltiplex thread exiting code
  CIFS: Move mid search to a separate function
  CIFS: Move RFC1002 check to a separate function
  CIFS: Simplify socket reading in demultiplex thread
  CIFS: Move buffer allocation to a separate function
  cifs: remove unneeded variable initialization in cifs_reconnect_tcon
  cifs: simplify refcounting for oplock breaks
  cifs: fix compiler warning in CIFSSMBQAllEAs
  cifs: fix name parsing in CIFSSMBQAllEAs
  cifs: don't start signing too early
  cifs: trivial: goto out here is unnecessary
  cifs: advertise the right receive buffer size to the server

* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
  gpio_msm: Move Qualcomm MSM v2 gpio driver into drivers
  gpio_msm: Move Qualcomm v6 MSM driver into drivers
  msm: gpio: Fold register defs into C file
  msm: gpiomux: Move public API to public header
  msm: gpio: Remove ifdefs on gpio chip registers
  msm: gpio: Remove chip-specific register definitions
  msm: Remove chip-ifdefs for GPIO io mappings
  msm: gpio: Remove unsupported devices
  gpio: ab8500: fix MODULE_ALIAS for ab8500
  of/gpio: export of_gpio_simple_xlate

* 'for-3.1-rc1' of git://gitorious.org/linux-omap-dss2/linux: (31 commits)
  OMAP: DSS2: HDMI: fix hdmi clock name
  HACK: OMAP: DSS2: clk hack for OMAP2/3
  OMAP: DSS2: DSS: Fix context save/restore
  OMAP: DSS2: DISPC: Fix context save/restore
  OMAP: DSS2: Remove ctx loss count from dss.c
  OMAP: DSS2: Remove unused code from display.c
  OMAP: DSS2: DISPC: remove finegrained clk enables/disables
  OMAP: DSS2: Remove unused opt_clock_available
  OMAP: DSS2: Use PM runtime & HWMOD support
  OMAP: DSS2: Remove CONFIG_OMAP2_DSS_SLEEP_BEFORE_RESET
  OMAP: DSS2: Remove core_dump_clocks
  OMAP: DSS2: DPI: remove unneeded SYSCK enable/disable
  OMAP: DSS2: Use omap_pm_get_dev_context_loss_count to get ctx loss count
  OMAP: DSS2: rewrite use of context_loss_count
  OMAP: DSS2: Remove clk optimization at dss init
  OMAP: DSS2: Fix init and unit sequence
  OMAP: DSS2: Clean up probe for DSS & DSI
  OMAP: DSS2: Handle dpll4_m4_ck in dss_get/put_clocks
  OMAP: DSS2: Fix FIFO threshold and burst size for OMAP4
  OMAP: DSS2: DSI: sync when disabling a display
  ...

* 'sh-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x: (39 commits)
  SH: static should be at beginning of declaration
  sh: move CLKDEV_xxx_ID macro to sh_clk.h
  sh: clock-shx3: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7786: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7785: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7757: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7366: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7343: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7722: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7724: add CLKDEV_ICK_ID for cleanup
  sh: clock-sh7366: modify I2C clock settings
  sh: clock-sh7343: modify I2C clock settings
  sh: clock-sh7723: modify I2C clock settings
  sh: clock-sh7722: modify I2C clock settings
  sh: clock-sh7724: modify I2C clock settings
  serial: sh-sci: Fix up pretty name printing for port IRQs.
  serial: sh-sci: Kill off per-port enable/disable callbacks.
  serial: sh-sci: Add missing module description/author bits.
  serial: sh-sci: Regtype probing doesn't need to be fatal.
  sh: Tidy up pre-clkdev clk_get() error handling.
  ...

Conflicts:
	drivers/gpio/Kconfig
	drivers/gpio/Makefile

Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Move reading to separate function and remove csocket variable.

Also change semantic in a little: goto incomplete_rcv only when
we get -EAGAIN (or a familiar error) while reading rfc1002 header.
In this case we don't check for echo timeout when we don't get whole
header at once, as it was before.
Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Migrate the driver for the v7-based MSM chips into drivers/gpio.  The
driver is unchanged, only moved.

Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

Migrate the driver for the v6-based MSM chips into drivers/gpio.  The
driver is unchanged, only moved.

Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

No need to have a separate header file containing only register
definitions that are used by a single driver.  Fold these into the
gpio driver.
Signed-off-by: David Brown <davidb@codeaurora.org>

The gpiomux.h header contains some SOC ifdefs.  However, the API that
is actually used by the GPIO driver only uses two functions that are
general.  Move these general definitions into a public header file.

Change-Id: Ia5df8af87dba268225598d56908e523bcfc24ef6
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

Select the GPIO register configuration at runtime rather than through
idefs.

Change-Id: I02ea0a3d61bc81669f32097c32420f0688552231
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

Put an SOC prefix on each GPIO register definition, eliminating the
need to have SOC ifdefs around the definitions.

Change-Id: I5a01fd328a89ce1be610847934d6e118f5465e42
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

The two GPIO controllers are always mapped to the same virtual address
across all MSM devices.  Instead of selecting this at compile time,
determine the physical address at runtime, eliminating yet something
else preventing multiple MSM targets from being compiled into the same
kernel.

Change-Id: I1672219d978ab6243526adeda6badf49472baa27
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

The MSM7x25 and MSM7x27 devices are not yet supported in the kernel.
Remove #ifdef-based tables supporting these chips for now.

Change-Id: I4d9f5abc4cc0942ce75a067097b072489493c1b8
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>

The HDMI clock (hdmi_clk) is missing in the current OMAP4 HWMOD
database. Fix this in the DSS driver by using the old clock name
(dss_48mhz_clk).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The HWMOD data for OMAP2 and 3 are currently not up to date regarding
DSS (OMAP4 HWMOD data is fine). This patch makes the DSS driver to get
the opt clocks needed for OMAP2/3 with the old clock names, thus
allowing DSS driver to use runtime PM.

The HWMOD databases should be fixes ASAP, and this patch can be reverted
after that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (46 commits)
  mfd: Fix mismatch in twl4030 mutex lock-unlock
  mfd: twl6030-pwm.c needs MODULE_LICENSE
  mfd: Fix the omap-usb-host clock API usage on usbhs_disable()
  mfd: Acknowledge WM8994 IRQs before reporting
  mfd: Acknowlege all WM831x IRQs before we handle them
  mfd: Avoid two assignments if failures happen in tps65910_i2c_probe
  regulator: Storing tps65912 error codes in u8
  mfd: Don't leak init_data in tps65910_i2c_probe
  regulator: aat2870: Add AAT2870 regulator driver
  backlight: Add AAT2870 backlight driver
  mfd: Add AAT2870 mfd driver
  mfd: Remove dead code from max8997-irq
  mfd: Move TPS55910 Kconfig option
  mfd: Fix missing stmpe kerneldoc
  mfd: Fix off-by-one value range checking for tps65912_i2c_write
  mfd: Add devices for WM831x clocking module
  mfd: Remove comp{1,2}_threshold sysfs entries in tps65911_comparator_remove
  mfd: Don't ask about the TPS65912 core driver in Kconfig
  mfd: Fix off by one in WM831x IRQ code
  mfd: Add tps65921 support from twl-core
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/math-emu: Remove unnecessary code
  m68k/math-emu: Remove commented out old code
  m68k: Kill warning in setup_arch() when compiling for Sun3
  m68k/atari: Prefix GPIO_{IN,OUT} with CODEC_
  sparc: iounmap() and *_free_coherent() - Use lookup_resource()
  m68k/atari: Reserve some ST-RAM early on for device buffer use
  m68k/amiga: Chip RAM - Use lookup_resource()
  resources: Add lookup_resource()
  sparc: _sparc_find_resource() should check for exact matches
  m68k/amiga: Chip RAM - Offset resource end by CHIP_PHYSADDR
  m68k/amiga: Chip RAM - Use resource_size() to fix off-by-one error
  m68k/amiga: Chip RAM - Change chipavail to an atomic_t
  m68k/amiga: Chip RAM - Always allocate from the start of memory
  m68k/amiga: Chip RAM - Convert from printk() to pr_*()
  m68k/amiga: Chip RAM - Use tabs for indentation

Fix two recently introduced compile problems:

Fix a typo in fs/nfs/pnfs.h

Move the pnfs_blksize declaration outside the CONFIG_NFS_V4 section in
struct nfs_server.
Reported-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A mutex is locked on entry into twl4030_madc_conversion().
Immediate return on some error conditions leaves the
mutex locked.

This patch ensures that mutex is always unlocked before
leaving the function.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

twl6030_pwm: module license 'unspecified' taints kernel.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Hemanth V <hemanthv@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

usbhs_disable function was invoking clk_enable() instead of
clk_disable(), thus only increasing the clock usage counter and
preventing this particular clock from being ever turned off.
Because of this, the power domain of omap4 the USB Host subsystem
would never reach lower power states.This patch calls clk_disable()
in usbhs_disable function
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This ensures we never have a window where we've handled an interrupt but
not told the hardware about it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Ensure that we never have a window where we've handled an interrupt (and
therefore need to be notified of new events) but haven't yet told the
interrupt controller that this is the case (so any new events will be
discarded).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In drivers/mfd/tps65910.c:tps65910_i2c_probe() there's potential for a
tiny optimization.

We assign to init_data->irq and init_data->irq_base long before we
need them, and there are two potential exits from the function before
they are needed.

Moving the assignments below these two potential exits means we
completely avoid doing them in these two (failure) cases.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

get_ctrl_reg() returns -EINVAL so the error handling won't work here
if reg is a u8.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

There are a couple of situations where we leak init_data in
drivers/mfd/tps65910.c:tps65910_i2c_probe() - this patch should take
care of them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add regulator driver for AnalogicTech AAT2870.
Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add backlight driver for AnalogicTech AAT2870.
Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add mfd core driver for AnalogicTech AAT2870.
The AAT2870 is communication through I2C and contains backlight and
regulator components.
Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We either hit one of the case's or the default in the switch statement
in get_i2c(), so the 'return ERR_PTR(-EINVAL);' at the end of the
function is just dead code - remove it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Having another TPS chip at the end of the Kconfig when all it's
relatives are grouped together in their own section seems totally
counter-intuitive. Move it, also in the Makefile.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>