- 15 Mar, 2022 10 commits
-
-
Jacob Keller authored
When ice_eswitch_configure fails, print an error message to make it more obvious why VF initialization did not succeed. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Jacob Keller authored
The ice_ena_vfs function and some of its sub-functions like ice_set_per_vf_res use a "if (<function>) { <print error> ; <exit> }" flow. This flow discards specialized errors reported by the called function. This style is generally not preferred as it makes tracing error sources more difficult. It also means we cannot log the actual error received properly. Refactor several calls in the ice_ena_vfs function that do this to catch the error in the 'ret' variable. Report this in the messages, and then return the more precise error value. Doing this reveals that ice_set_per_vf_res returns -EINVAL or -EIO in places where -ENOSPC makes more sense. Fix these calls up to return the more appropriate value. Signed-off-by:Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by:
-
Jacob Keller authored
The ice_set_vf_port_vlan function is located in ice_sriov.c very far away from the other .ndo operations that it is similar to. Move this so that its located near the other .ndo operation definitions. Signed-off-by:
-
Jacob Keller authored
The API to control the VSI spoof checking for a VF VSI has three functions: enable, disable, and set. The set function takes the VSI and the VF and decides whether to call enable or disable based on the vf->spoofchk field. In some flows, vf->spoofchk is not yet set, such as the function used to control the setting for a VF. (vf->spoofchk is only updated after a success). Simplify this API by refactoring ice_vf_set_spoofchk_cfg to be "ice_vsi_apply_spoofchk" which takes the boolean and allows all callers to avoid having to determine whether to call enable or disable themselves. This matches the expected callers better, and will prevent the need to export more than one function when this code must be called from another file. Signed-off-by:
-
Jacob Keller authored
The ICE_MAX_VF_COUNT field is defined in ice_sriov.h. This count is true for SR-IOV but will not be true for all VF implementations, such as when the ice driver supports Scalable IOV. Rename this definition to clearly indicate ICE_MAX_SRIOV_VFS. Signed-off-by:
-
Jacob Keller authored
A few more macros exist in ice_sriov.h which are not used anywhere. These can be safely removed. Note that ICE_VIRTCHNL_VF_CAP_L2 capability is set but never checked anywhere in the driver. Thus it is also safe to remove. Signed-off-by:
-
Jacob Keller authored
The vc_ops structure is used to allow different handlers for virtchnl commands when the driver is in representor mode. The current implementation uses a copy of the ops table in each VF, and modifies this copy dynamically. The usual practice in kernel code is to store the ops table in a constant structure and point to different versions. This has a number of advantages: 1. Reduced memory usage. Each VF merely points to the correct table, so they're able to re-use the same constant lookup table in memory. 2. Consistency. It becomes more difficult to accidentally update or edit only one op call. Instead, the code switches to the correct able by a single pointer write. In general this is atomic, either the pointer is updated or its not. 3. Code Layout. The VF structure can store a pointer to the table without needing to have the full structure definition defined prior to the VF structure definition. This will aid in future refactoring of code by allowing the VF pointer to be kept in ice_vf_lib.h while the virtchnl ops table can be maintained in ice_virtchnl.h There is one major downside in the case of the vc_ops structure. Most of the operations in the table are the same between the two current implementations. This can appear to lead to duplication since each implementation must now fill in the complete table. It could make spotting the differences in the representor mode more challenging. Unfortunately, methods to make this less error prone either add complexity overhead (macros using CPP token concatenation) or don't work on all compilers we support (constant initializer from another constant structure). The cost of maintaining two structures does not out weigh the benefits of the constant table model. While we're making these changes, go ahead and rename the structure and implementations with "virtchnl" instead of "vc_vf_". This will more closely align with the planned file renaming, and avoid similar names when we later introduce a "vf ops" table for separating Scalable IOV and Single Root IOV implementations. Leave the accessor/assignment functions in order to avoid issues with compiling with options disabled. The interface makes it easier to handle when CONFIG_PCI_IOV is disabled in the kernel. Signed-off-by: -
Jacob Keller authored
Several headers in the ice driver include ice.h even though they are themselves included by that header. The most notable of these is ice_common.h, but several other headers also do this. Such a recursive inclusion is problematic as it forces headers to be included in a strict order, otherwise compilation errors can result. The circular inclusions do not trigger an endless loop due to standard header inclusion guards, however other errors can occur. For example, ice_flow.h defines ice_rss_hash_cfg, which is used by ice_sriov.h as part of the definition of ice_vf_hash_ip_ctx. ice_flow.h includes ice_acl.h, which includes ice_common.h, and which finally includes ice.h. Since ice.h itself includes ice_sriov.h, this creates a circular dependency. The definition in ice_sriov.h requires things from ice_flow.h, but ice_flow.h itself will lead to trying to load ice_sriov.h as part of its process for expanding ice.h. The current code avoids this issue by having an implicit dependency without the include of ice_flow.h. If we were to fix that so that ice_sriov.h explicitly depends on ice_flow.h the following pattern would occur: ice_flow.h -> ice_acl.h -> ice_common.h -> ice.h -> ice_sriov.h At this point, during the expansion of, the header guard for ice_flow.h is already set, so when ice_sriov.h attempts to load the ice_flow.h header it is skipped. Then, we go on to begin including the rest of ice_sriov.h, including structure definitions which depend on ice_rss_hash_cfg. This produces a compiler warning because ice_rss_hash_cfg hasn't yet been included. Remember, we're just at the start of ice_flow.h! If the order of headers is incorrect (ice_flow.h is not implicitly loaded first in all files which include ice_sriov.h) then we get the same failure. Removing this recursive inclusion requires fixing a few cases where some headers depended on the header inclusions from ice.h. In addition, a few other changes are also required. Most notably, ice_hw_to_dev is implemented as a macro in ice_osdep.h, which is the likely reason that ice_common.h includes ice.h at all. This macro implementation requires the full definition of ice_pf in order to properly compile. Fix this by moving it to a function declared in ice_main.c, so that we do not require all files to depend on the layout of the ice_pf structure. Note that this change only fixes circular dependencies, but it does not fully resolve all implicit dependencies where one header may depend on the inclusion of another. I tried to fix as many of the implicit dependencies as I noticed, but fixing them all requires a somewhat tedious analysis of each header and attempting to compile it separately. Signed-off-by:
-
Jacob Keller authored
The ice_virtchnl_pf.c and ice_virtchnl_pf.h files are where most of the code for implementing Single Root IOV virtualization resides. This code includes support for bringing up and tearing down VFs, hooks into the kernel SR-IOV netdev operations, and for handling virtchnl messages from VFs. In the future, we plan to support Scalable IOV in addition to Single Root IOV as an alternative virtualization scheme. This implementation will re-use some but not all of the code in ice_virtchnl_pf.c To prepare for this future, we want to refactor and split up the code in ice_virtchnl_pf.c into the following scheme: * ice_vf_lib.[ch] Basic VF structures and accessors. This is where scheme-independent code will reside. * ice_virtchnl.[ch] Virtchnl message handling. This is where the bulk of the logic for processing messages from VFs using the virtchnl messaging scheme will reside. This is separated from ice_vf_lib.c because it is distinct and has a bulk of the processing code. * ice_sriov.[ch] Single Root IOV implementation, including initialization and the routines for interacting with SR-IOV based netdev operations. * (future) ice_siov.[ch] Scalable IOV implementation. As a first step, lets assume that all of the code in ice_virtchnl_pf.[ch] is for Single Root IOV. Rename this file to ice_sriov.c and its header to ice_sriov.h Future changes will further split out the code in these files following the plan outlined here. Signed-off-by:
-
Jacob Keller authored
The ice_sriov.c file primarily contains code which handles the logic for mailbox overflow detection and some other utility functions related to the virtualization mailbox. The bulk of the SR-IOV implementation is actually found in ice_virtchnl_pf.c, and this file isn't strictly SR-IOV specific. In the future, the ice driver will support an additional virtualization scheme known as Scalable IOV, and the code in this file will be used for this alternative implementation. Rename this file (and its associated header) to ice_vf_mbx.c, so that we can later re-use the ice_sriov.c file as the SR-IOV specific file. Signed-off-by:
-
- 14 Mar, 2022 23 commits
-
-
Niklas Söderlund authored
Fix the following coccicheck warning: drivers/net/ethernet/netronome/nfp/flower/action.c:959:7-69: WARNING avoid newline at end of message in NL_SET_ERR_MSG_MOD Signed-off-by:Niklas Söderlund <niklas.soderlund@corigine.com> Signed-off-by:
Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20220312095823.2425775-1-niklas.soderlund@corigine.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Saeed Mahameed authored
We need to sync page pool stats only for active channels. Reading ethtool stats on a down netdev or a netdev with modified number of channels will result in a user-after-free, trying to access page pools that are freed already. BUG: KASAN: use-after-free in mlx5e_stats_grp_sw_update_stats+0x465/0xf80 Read of size 8 at addr ffff888004835e40 by task ethtool/720 Fixes: cc10e84b ("mlx5: add support for page_pool_get_stats") Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com> Reported-by:
Joe Damato <jdamato@fastly.com> Link: https://lore.kernel.org/r/20220312005353.786255-1-saeed@kernel.orgSigned-off-by:
-
Julia Lawall authored
Use kzalloc instead of kmalloc + memset. The semantic patch that makes this change is: (https://coccinelle.gitlabpages.inria.fr/website/) //<smpl> @@ expression res, size, flag; @@ - res = kmalloc(size, flag); + res = kzalloc(size, flag); ... - memset(res, 0, size); //</smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@inria.fr> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20220312102705.71413-3-Julia.Lawall@inria.frSigned-off-by:
-
Eric Dumazet authored
syzbot was kind enough to remind us that dev->{tx_dropped|rx_dropped} could be increased in process context. BUG: using smp_processor_id() in preemptible [00000000] code: syz-executor413/3593 caller is netdev_core_stats_alloc+0x98/0x110 net/core/dev.c:10298 CPU: 1 PID: 3593 Comm: syz-executor413 Not tainted 5.17.0-rc7-syzkaller-02426-g97aeb877 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 check_preemption_disabled+0x16b/0x170 lib/smp_processor_id.c:49 netdev_core_stats_alloc+0x98/0x110 net/core/dev.c:10298 dev_core_stats include/linux/netdevice.h:3855 [inline] dev_core_stats_rx_dropped_inc include/linux/netdevice.h:3866 [inline] tun_get_user+0x3455/0x3ab0 drivers/net/tun.c:1800 tun_chr_write_iter+0xe1/0x200 drivers/net/tun.c:2015 call_write_iter include/linux/fs.h:2074 [inline] new_sync_write+0x431/0x660 fs/read_write.c:503 vfs_write+0x7cd/0xae0 fs/read_write.c:590 ksys_write+0x12d/0x250 fs/read_write.c:643 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f2cf4f887e3 Code: 5d 41 5c 41 5d 41 5e e9 9b fd ff ff 66 2e 0f 1f 84 00 00 00 00 00 90 64 8b 04 25 18 00 00 00 85 c0 75 14 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 55 c3 0f 1f 40 00 48 83 ec 28 48 89 54 24 18 RSP: 002b:00007ffd50dd5fd8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 00007ffd50dd6000 RCX: 00007f2cf4f887e3 RDX: 000000000000002a RSI: 0000000000000000 RDI: 00000000000000c8 RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007ffd50dd5ff0 R14: 00007ffd50dd5fe8 R15: 00007ffd50dd5fe4 </TASK> Fixes: 625788b5 ("net: add per-cpu storage and net->core_stats") Signed-off-by:Eric Dumazet <edumazet@google.com> Cc: jeffreyji <jeffreyji@google.com> Cc: Brian Vazquez <brianvv@google.com> Acked-by:
Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20220312214505.3294762-1-eric.dumazet@gmail.comSigned-off-by:
-
Julia Lawall authored
Various spelling mistakes in comments. Detected with the help of Coccinelle. Signed-off-by:
-
David S. Miller authored
Ioana Ciornei says: ==================== dpaa2-mac: add support for changing the protocol at runtime This patch set adds support for changing the Ethernet protocol at runtime on Layerscape SoCs which have the Lynx 28G SerDes block. The first two patches add a new generic PHY driver for the Lynx 28G and the bindings file associated. The driver reads the PLL configuration at probe time (the frequency provided to the lanes) and determines what protocols can be supported. Based on this the driver can deny or approve a request from the dpaa2-mac to setup a new protocol. The next 2 patches add some MC APIs for inquiring what is the running version of firmware and setting up a new protocol on the MAC. Moving along, we extract the code for setting up the supported interfaces on a MAC on a different function since in the next patches will update the logic. In the next patch, the dpaa2-mac is updated so that it retrieves the SerDes PHY based on the OF node and in case of a major reconfig, call the PHY driver to set up the new protocol on the associated lane and the MC firmware to reconfigure the MAC side of things. Finally, the LX2160A dtsi is annotated with the SerDes PHY nodes for the 1st SerDes block. Beside this, the LX2160A Clearfog dtsi is annotated with the 'phys' property for the exposed SFP cages. Changes in v2: - 1/8: add MODULE_LICENSE Changes in v3: - 2/8: fix 'make dt_binding_check' errors - 7/8: reverse order of dpaa2_mac_start() and phylink_start() - 7/8: treat all RGMII variants in dpmac_eth_if_mode - 7/8: remove the .mac_prepare callback - 7/8: ignore PHY_INTERFACE_MODE_NA in validate Changes in v4: - 1/8: remove the DT nodes parsing - 1/8: add an xlate function - 2/8: remove the children phy nodes for each lane - 7/8: rework the of_phy_get if statement - 8/8: remove the DT nodes for each lane and the lane id in the phys phandle Changes in v5: - 2/8: use phy as the name of the DT node in the example ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Ioana Ciornei authored
Describe the SerDes block #1 using the generic phys infrastructure. This way, the ethernet nodes can each reference their serdes lanes individually using the 'phys' dts property. Signed-off-by:
Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by:
-
Ioana Ciornei authored
This patch integrates the dpaa2-eth driver with the generic PHY infrastructure in order to search, find and reconfigure the SerDes lanes in case of a protocol change. On the .mac_config() callback, the phy_set_mode_ext() API is called so that the Lynx 28G SerDes PHY driver can change the lane's configuration. In the same phylink callback the MC firmware is called so that it reconfigures the MAC side to run using the new protocol. The consumer drivers - dpaa2-eth and dpaa2-switch - are updated to call the dpaa2_mac_start/stop functions newly added which will power_on/power_off the associated SerDes lane. Signed-off-by:
-
Ioana Ciornei authored
The logic to setup the supported interfaces will get annotated based on what the configuration of the SerDes PLLs supports. Move the current setup into a separate function just to try to keep it clean. Signed-off-by:
-
Ioana Ciornei authored
Retrieve the API version running on the firmware and based on it detect which features are available for usage. The first one to be listed is the capability to change the MAC protocol at runtime. Signed-off-by:
-
Ioana Ciornei authored
The MC firmware gained recently a new command which can reconfigure the running protocol on the underlying MAC. Add this new command which will be used in the next patches in order to do a major reconfig on the interface. Signed-off-by:
-
Ioana Ciornei authored
The dpmac_get_api_version command will be used in the next patches to determine if the current firmware is capable or not to change the Ethernet protocol running on the MAC. Signed-off-by:
-
Ioana Ciornei authored
Add device tree binding for the Lynx 28G SerDes PHY driver used on Layerscape based SoCs. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
Ioana Ciornei authored
This patch adds a new generic PHY driver to support the Lynx 28G SerDes block found on some of the Layerscape SoCs such as LX2160A. At the moment, only the following Ethernet protocols are supported: SGMII/1000Base-X and 10GBaseR. SerDes lanes which are not running an Ethernet protocol or a currently supported Ethenet protocol will be left as it was configured through the RCW (Reset Configuration Word) at boot time. At probe time, the platform driver will read the current configuration of both PLLs found on a SerDes block and will determine what protocols are supported using that PLL. For example, if a PLL is configured to generate a clock net (frate) of 5GHz the only protocols sustained by that PLL are SGMII/1000Base-X (using a quarter of the full clock rate) and QSGMII using the full clock net frequency on the lane. On the .set_mode() callback, the PHY driver will first check if the requested operating mode (protocol) is even supported by the current PLL configuration and will error out if not. Then, the lane is reconfigured to run on the requested protocol. Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Basic QoS classification on Felix DSA switch using dcbnl Basic QoS classification for Ocelot switches means port-based default priority, DSCP-based and VLAN PCP based. This is opposed to advanced QoS classification which is done through the VCAP IS1 TCAM based engine. The patch set is a logical continuation of this RFC which attempted to describe the default-prio as a matchall entry placed at the end of a series of offloaded tc filters: https://patchwork.kernel.org/project/netdevbpf/cover/20210113154139.1803705-1-olteanv@gmail.com/ I have tried my best to satisfy the feedback that we should cater for pre-configured QoS profiles. Ironically, the only pre-configured QoS profile that the Felix switch driver has is for VLAN PCP (1:1 mapping with QoS class), yet IEEE 802.1Q or dcbnl offer no mechanism for reporting or changing that. Testing was done with the iproute2 dcb app. The qos_class of packets was dumped from net/dsa/tag_ocelot.c. (1) $ dcb app show dev swp3 default-prio 0 (2) $ dcb app replace dev swp3 default-prio 3 (3) $ dcb app replace dev swp3 dscp-prio CS3:5 (4) $ dcb app replace dev swp3 dscp-prio CS2:2 (5) $ dcb app show dev swp3 default-prio 3 dscp-prio CS2:2 CS3:5 Traffic sent with "ping -Q 64 <ipaddr>", which means CS2. These packets match qos_class 0 after command (1), qos_class 3 after command (2), qos_class 3 after command (3), and qos_class 2 after command (2). ==================== Signed-off-by:
-
Vladimir Oltean authored
Follow the established programming model for this driver and provide shims in the felix DSA driver which call the implementations from the ocelot switch lib. The ocelot switchdev driver wasn't integrated with dcbnl due to lack of hardware availability. The switch doesn't have any fancy QoS classification enabled by default. The provided getters will create a default-prio app table entry of 0, and no dscp entry. However, the getters have been made to actually retrieve the hardware configuration rather than static values, to be future proof in case DSA will need this information from more call paths. For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG, called QOS_DEFAULT_VAL. DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG (field QOS_DSCP_ENA), and individual DSCP values are configured as trusted or not through register ANA_DSCP_CFG (replicated 64 times). An untrusted DSCP value falls back to other QoS classification methods. If trusted, the selected ANA_DSCP_CFG register also holds the QoS class in the QOS_DSCP_VAL field. The hardware also supports DSCP remapping (DSCP value X is translated to DSCP value Y before the QoS class is determined based on the app table entry for Y) and DSCP packet rewriting. The dcbnl framework, for being so flexible in other useless areas, doesn't appear to support this. So this functionality has been left out. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
Similar to the port-based default priority, IEEE 802.1Q-2018 allows the Application Priority Table to define QoS classes (0 to 7) per IP DSCP value (0 to 63). In the absence of an app table entry for a packet with DSCP value X, QoS classification for that packet falls back to other methods (VLAN PCP or port-based default). The presence of an app table for DSCP value X with priority Y makes the hardware classify the packet to QoS class Y. As opposed to the default-prio where DSA exposes only a "set" in dsa_switch_ops (because the port-based default is the fallback, it always exists, either implicitly or explicitly), for DSCP priorities we expose an "add" and a "del". The addition of a DSCP entry means trusting that DSCP priority, the deletion means ignoring it. Drivers that already trust (at least some) DSCP values can describe their configuration in dsa_switch_ops :: port_get_dscp_prio(), which is called for each DSCP value from 0 to 63. Again, there can be more than one dcbnl app table entry for the same DSCP value, DSA chooses the one with the largest configured priority. Signed-off-by:
-
Vladimir Oltean authored
The port-based default QoS class is assigned to packets that lack a VLAN PCP (or the port is configured to not trust the VLAN PCP), an IP DSCP (or the port is configured to not trust IP DSCP), and packets on which no tc-skbedit action has matched. Similar to other drivers, this can be exposed to user space using the DCB Application Priority Table. IEEE 802.1Q-2018 specifies in Table D-8 - Sel field values that when the Selector is 1, the Protocol ID value of 0 denotes the "Default application priority. For use when application priority is not otherwise specified." The way in which the dcbnl integration in DSA has been designed has to do with its requirements. Andrew Lunn explains that SOHO switches are expected to come with some sort of pre-configured QoS profile, and that it is desirable for this to come pre-loaded into the DSA slave interfaces' DCB application priority table. In the dcbnl design, this is possible because calls to dcb_ieee_setapp() can be initiated by anyone including being self-initiated by this device driver. However, what makes this challenging to implement in DSA is that the DSA core manages the net_devices (effectively hiding them from drivers), while drivers manage the hardware. The DSA core has no knowledge of what individual drivers' QoS policies are. DSA could export to drivers a wrapper over dcb_ieee_setapp() and these could call that function to pre-populate the app priority table, however drivers don't have a good moment in time to do this. The dsa_switch_ops :: setup() method gets called before the net_devices are created (dsa_slave_create), and so is dsa_switch_ops :: port_setup(). What remains is dsa_switch_ops :: port_enable(), but this gets called upon each ndo_open. If we add app table entries on every open, we'd need to remove them on close, to avoid duplicate entry errors. But if we delete app priority entries on close, what we delete may not be the initial, driver pre-populated entries, but rather user-added entries. So it is clear that letting drivers choose the timing of the dcb_ieee_setapp() call is inappropriate. The alternative which was chosen is to introduce hardware-specific ops in dsa_switch_ops, and effectively hide dcbnl details from drivers as well. For pre-populating the application table, dsa_slave_dcbnl_init() will call ds->ops->port_get_default_prio() which is supposed to read from hardware. If the operation succeeds, DSA creates a default-prio app table entry. The method is called as soon as the slave_dev is registered, but before we release the rtnl_mutex. This is done such that user space sees the app table entries as soon as it sees the interface being registered. The fact that we populate slave_dev->dcbnl_ops with a non-NULL pointer changes behavior in dcb_doit() from net/dcb/dcbnl.c, which used to return -EOPNOTSUPP for any dcbnl operation where netdev->dcbnl_ops is NULL. Because there are still dcbnl-unaware DSA drivers even if they have dcbnl_ops populated, the way to restore the behavior is to make all dcbnl_ops return -EOPNOTSUPP on absence of the hardware-specific dsa_switch_ops method. The dcbnl framework absurdly allows there to be more than one app table entry for the same selector and protocol (in other words, more than one port-based default priority). In the iproute2 dcb program, there is a "replace" syntactical sugar command which performs an "add" and a "del" to hide this away. But we choose the largest configured priority when we call ds->ops->port_set_default_prio(), using __fls(). When there is no default-prio app table entry left, the port-default priority is restored to 0. Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210113154139.1803705-2-olteanv@gmail.com/Signed-off-by:
-
Victor Nogueira authored
Some tests, such as Test d052: Add 1M filters with the same action, may not work with a small timeout value. Increase timeout to 24 seconds. Signed-off-by:
Victor Nogueira <victor@mojatatu.com> Acked-by:
Davide Caratti <dcaratti@redhat.com> Signed-off-by:
-
Sebastian Andrzej Siewior authored
____napi_schedule() needs to be invoked with disabled interrupts due to __raise_softirq_irqoff (in order not to corrupt the per-CPU list). ____napi_schedule() needs also to be invoked from an interrupt context so that the raised-softirq is processed while the interrupt context is left. Add lockdep asserts for both conditions. While this is the second time the irq/softirq check is needed, provide a generic lockdep_assert_softirq_will_run() which is used by both caller. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
David S. Miller authored
Ziyang Xuan says: ==================== net: macvlan: fix potential UAF problem for lowerdev Add the reference operation to lowerdev of macvlan to avoid the potential UAF problem under the following known scenario: Someone module puts the NETDEV_UNREGISTER event handler to a work, and lowerdev is accessed in the work handler. But when the work is excuted, lowerdev has been destroyed because upper macvlan did not get reference to lowerdev correctly. In addition, add net device refcount tracker to macvlan. ==================== Signed-off-by: -
Ziyang Xuan authored
Add net device refcount tracker to macvlan. Signed-off-by:
Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by:
-
Ziyang Xuan authored
Add the reference operation to lowerdev of macvlan to avoid the potential UAF problem under the following known scenario: Someone module puts the NETDEV_UNREGISTER event handler to a work, and lowerdev is accessed in the work handler. But when the work is excuted, lowerdev has been destroyed because upper macvlan did not get reference to lowerdev correctly. That likes as the scenario occurred by commit 563bcbae ("net: vlan: fix a UAF in vlan_dev_real_dev()"). Signed-off-by:
-
- 13 Mar, 2022 7 commits
-
-
David S. Miller authored
Merge tag 'linux-can-next-for-5.18-20220313' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next linux-can-next-for-5.18-20220313 Marc Kleine-Budde says: ==================== pull-request: can-next 2022-03-13 this is a pull request of 13 patches for net-next/master. The 1st patch is by me and fixes the freeing of a skb in the vxcan driver (initially added in this net-next window). The remaining 12 patches are also by me and target the mcp251xfd driver. The first patch fixes a printf modifier (initially added in this net-next window). The remaining patches add ethtool based ring and RX/TX IRQ coalescing support to the driver. ==================== Signed-off-by:
-
Marc Kleine-Budde authored
This patch increases the number of RX-FIFOs to 3 and the max TX-FIFO depth to 16. This leads to the following default ring configuration. CAN-2.0 mode: | FIFO setup: TEF: 0x400: 8*12 bytes = 96 bytes | FIFO setup: RX-0: FIFO 1/0x460: 32*20 bytes = 640 bytes | FIFO setup: RX-1: FIFO 2/0x6e0: 32*20 bytes = 640 bytes | FIFO setup: RX-2: FIFO 3/0x960: 16*20 bytes = 320 bytes | FIFO setup: TX: FIFO 4/0xaa0: 8*16 bytes = 128 bytes | FIFO setup: free: 224 bytes CAN-FD mode: | FIFO setup: TEF: 0x400: 4*12 bytes = 48 bytes | FIFO setup: RX-0: FIFO 1/0x430: 16*76 bytes = 1216 bytes | FIFO setup: RX-1: FIFO 2/0x8f0: 4*76 bytes = 304 bytes | FIFO setup: TX: FIFO 3/0xa20: 4*72 bytes = 288 bytes | FIFO setup: free: 192 bytes With the previously added ethtool ring configuration support the RAM on the chip can now be runtime configured between RX and TX buffers. Link: https://lore.kernel.org/20220313083640.501791-13-mkl@pengutronix.deSigned-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Marc Kleine-Budde authored
This patch adds support ethtool based configuration for the TX IRQ coalescing added in the previous patch. Link: https://lore.kernel.org/20220313083640.501791-12-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds TX IRQ coalescing support to the driver. The implemented algorithm is similar to the RX IRQ coalescing support added in the previous patch. Link: https://lore.kernel.org/20220313083640.501791-11-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds support ethtool based configuration for the RX IRQ coalescing added in the previous patch. Link: https://lore.kernel.org/20220313083640.501791-10-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds RX IRQ coalescing support to the driver. The mcp251xfd chip doesn't support proper hardware based coalescing, so this patch tries to implemented it in software. The RX-FIFO offers a "FIFO not empty" interrupt, which is used if no coalescing is active. With activated RX IRQ coalescing the "FIFO not empty" interrupt is disabled in the RX IRQ handler and the "FIFO half full" or "FIFO full interrupt" (depending on RX max coalesced frames IRQ) is used instead. To avoid RX CAN frame starvation a hrtimer is setup with RX coalesce usecs IRQ,on timer expiration the "FIFO not empty" is enabled again. Support for ethtool configuration is added in the next patch. Link: https://lore.kernel.org/20220313083640.501791-9-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch adds runtime configurable RX and TX ring parameters via ethtool to the driver. Link: https://lore.kernel.org/20220313083640.501791-8-mkl@pengutronix.deSigned-off-by:
-
