PHY of the i225 device support only copper mode.
There is no point to check media type in the
igc_power_up_link() method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the implementation of igc_power_down_link()
method was just calling igc_power_down_phy_copper_base()
method.
We can just call igc_power_down_phy_copper_base()
method directly.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

TCP segmentation TX context fail counter is not
applicable for i225 devices.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown<aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add EEE TX LPI and EEE RX LPI counters. A EEE TX LPI event
occurs when the transmitter enters EEE (IEEE 802.3az) LPI
state. A EEE RX LPI event occurs when the receiver detect
link partner entry into EEE(IEEE 802.3az) LPI state.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When Rx timestamping is enabled, we set the timestamp bit in SRRCTL
register for each queue, but we don't clear it when disabling. This
patch fixes igc_ptp_disable_rx_timestamp() accordingly.

Also, this patch gets rid of igc_ptp_enable_tstamp_rxqueue() and
igc_ptp_enable_tstamp_all_rxqueues() and move their logic into
igc_ptp_enable_rx_timestamp() to keep the enable and disable
helpers symmetric.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Current igc_ptp_set_timestamp_mode() logic is a bit tangled since it
handles many different hardware configurations in one single place,
making it harder to follow. This patch untangles that code by breaking
it into helper functions.

Quick note about the hw->mac.type check which was removed in this
refactoring: this check it not really needed since igc_i225 is the only
type supported by the IGC driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

As implemented in igc_ethtool_get_ts_info(), igc only supports HWTSTAMP_
FILTER_ALL so any HWTSTAMP_FILTER_* option the user may set falls back to
HWTSTAMP_FILTER_ALL.

HWTSTAMP_FILTER_ALL is implemented via Rx Time Sync Control (TSYNCRXCTL)
configuration which timestamps all incoming packets. Configuring a
UDP filter, in addition to TSYNCRXCTL, doesn't add much so this patch
removes that code. It also takes this opportunity to remove some
non-applicable comments.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The __IGC_PTP_TX_IN_PROGRESS flag indicates we have a pending Tx
timestamp. In some places, instead of checking that flag, we check
adapter->ptp_tx_skb. This patch fixes those places to use the flag.

Quick note about igc_ptp_tx_hwtstamp() change: when that function is
called, adapter->ptp_tx_skb is expected to be valid always so we
WARN_ON_ONCE() in case it is not.

Quick note about igc_ptp_suspend() change: when suspending, we don't
really need to check if there is a pending timestamp. We can simply
clear it unconditionally.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The functions igc_ptp_tx_hang() and igc_ptp_tx_work() have duplicate
code which handles Tx timestamp timeouts. This patch does a trivial
refactoring by moving that code to its own function and reusing it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Differently from I210, I225 doesn't report Rx timestamps via the TS bit
Rx descriptor + RXSTMPL/RXSTMPH registers mechanism. Rx timestamps are
reported in the packet buffer only, which is implemented by igc_ptp_rx_
pktstamp(). So this patch removes igc_ptp_rx_rgtstamp() and all code
related to it, copied from igb driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The LTR message on the PCIe inform the requested latency
on which the PCIe must become active to the downstream
PCIe port of the system.
This patch provide recommended LTR parameters by i225
specification.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

IEEE802.3az-2010 Energy Efficient Ethernet has been
approved as standard (September 2010) and the driver
can enable and disable it via ethtool.
Disable the feature by default on parts which support it.
Add enable/disable eee options.
tx-lpi, tx-timer and advertise not supported yet.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use list_empty_careful() instead of open-coding.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use list_is_singular() instead of open-coding.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix some coding-style issues, including one which
made the function pointers in the struct ei_device
hard to understand.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that all net_device operations are bundled together inside
mscc_ocelot.ko and no longer part of the common library, there's no
reason to export these symbols.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: make RTL8401 a separate chip version

So far RTL8401 was treated like a RTL8101e, means we relied on the BIOS
to configure MAC and PHY properly. Make RTL8401 a separate chip version
and copy MAC / PHY config from r8101 vendor driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

So far RTL8401 was treated like a RTL8101e, means we relied on the BIOS
to configure MAC and PHY properly. Make RTL8401 a separate chip version
and copy MAC / PHY config from r8101 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Chip versions 13, 14, 15 are treated the same by the driver, therefore
let's merge them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Luc Van Oostenryck says:

====================
net: always use netdev_tx_t for xmit()'s return type

The ndo_start_xmit() methods should return a 'netdev_tx_t', not
an int, and so should return NETDEV_TX_OK, not 0.
The patches in the series fix most of the remaning drivers and
subsystems (those included in allyesconfig on x86).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too and
returning NETDEV_TX_OK instead of 0 accordingly.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too and
returning NETDEV_TX_OK instead of 0 accordingly.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Metadata need not be collected in receive if the packet from bareudp
device is not targeted to openvswitch.
Signed-off-by: Martin <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Luo bin says:

====================
hinic: add some ethtool ops support

patch #1: support to set and get pause params with
          "ethtool -A/a" cmd
patch #2: support to set and get irq coalesce params with
          "ethtool -C/c" cmd
patch #3: support to do self test with "ethtool -t" cmd
patch #4: support to identify physical device with "ethtool -p" cmd
patch #5: support to get eeprom information with "ethtool -m" cmd
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

add support to get eeprom information from the plug-in module
with ethtool -m cmd.
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add support to identify physical device by flashing an LED
attached to it with ethtool -p cmd.
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add support to excute internal and external loopback test with
ethtool -t cmd.
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>