Skip to content

L
linux
Switch branch/tag
  1. 12 Mar, 2015 13 commits
  3. 10 Mar, 2015 3 commits
  5. 07 Mar, 2015 1 commit
  7. 05 Mar, 2015 21 commits
    • Alan Stern's avatar
      USB: EHCI: adjust error return code · 8920e92c
      Alan Stern authored 
      commit c401e7b4 upstream.

The USB stack uses error code -ENOSPC to indicate that the periodic
schedule is too full, with insufficient bandwidth to accommodate a new
allocation.  It uses -EFBIG to indicate that an isochronous transfer
could not be linked into the schedule because it would exceed the
number of isochronous packets the host controller driver can handle
(generally because the new transfer would extend too far into the
future).

ehci-hcd uses the wrong error code at one point.  This patch fixes it,
along with a misleading comment and debugging message.
Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      8920e92c
    • Ian Abbott's avatar
      staging: comedi: cb_pcidas64: fix incorrect AI range code handling · 5bebf228
      Ian Abbott authored 
      commit be8e8908 upstream.

The hardware range code values and list of valid ranges for the AI
subdevice is incorrect for several supported boards.  The hardware range
code values for all boards except PCI-DAS4020/12 is determined by
calling `ai_range_bits_6xxx()` based on the maximum voltage of the range
and whether it is bipolar or unipolar, however it only returns the
correct hardware range code for the PCI-DAS60xx boards.  For
PCI-DAS6402/16 (and /12) it returns the wrong code for the unipolar
ranges.  For PCI-DAS64/Mx/16 it returns the wrong code for all the
ranges and the comedi range table is incorrect.

Change `ai_range_bits_6xxx()` to use a look-up table pointed to by new
member `ai_range_codes` of `struct pcidas64_board` to map the comedi
range table indices to the hardware range codes.  Use a new comedi range
table for the PCI-DAS64/Mx/16 boards (and the commented out variants).
Signed-off-by: default avatarIan Abbott <abbotti@mev.co.uk>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      5bebf228
    • Kalle Valo's avatar
      ath6kl: fix struct hif_scatter_req list handling · 52235599
      Kalle Valo authored 
      commit 31b9cc9a upstream.

Jason noticed that with Yocto GCC 4.8.1 ath6kl crashes with this iperf command:

iperf -c $TARGET_IP -i 5 -t 50 -w 1M

The crash was:

Unable to handle kernel paging request at virtual address 1a480000
pgd = 80004000
[1a480000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ath6kl_sdio ath6kl_core [last unloaded: ath6kl_core]
CPU: 0 PID: 1953 Comm: kworker/u4:0 Not tainted 3.10.9-1.0.0_alpha+dbf364b #1
Workqueue: ath6kl ath6kl_sdio_write_async_work [ath6kl_sdio]
task: dcc9a680 ti: dc9ae000 task.ti: dc9ae000
PC is at v7_dma_clean_range+0x20/0x38
LR is at dma_cache_maint_page+0x50/0x54
pc : [<8001a6f8>]    lr : [<800170fc>]    psr: 20000093
sp : dc9afcf8  ip : 8001a748  fp : 00000004
r10: 00000000  r9 : 00000001  r8 : 00000000
r7 : 00000001  r6 : 00000000  r5 : 80cb7000  r4 : 03f9a480
r3 : 0000001f  r2 : 00000020  r1 : 1a480000  r0 : 1a480000
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 6cc5004a  DAC: 00000015
Process kworker/u4:0 (pid: 1953, stack limit = 0xdc9ae238)
Stack: (0xdc9afcf8 to 0xdc9b0000)
fce0:                                                       80c9b29c 00000000
fd00: 00000000 80017134 8001a748 dc302ac0 00000000 00000000 dc454a00 80c12ed8
fd20: dc115410 80017238 00000000 dc454a10 00000001 80017588 00000001 00000000
fd40: 00000000 dc302ac0 dc9afe38 dc9afe68 00000004 80c12ed8 00000000 dc454a00
fd60: 00000004 80436f88 00000000 00000000 00000600 0000ffff 0000000c 80c113c4
fd80: 80c9b29c 00000001 00000004 dc115470 60000013 dc302ac0 dc46e000 dc302800
fda0: dc9afe10 dc302b78 60000013 dc302ac0 dc46e000 00000035 dc46e5b0 80438c90
fdc0: dc9afe10 dc302800 dc302800 dc9afe68 dc9afe38 80424cb4 00000005 dc9afe10
fde0: dc9afe20 80424de8 dc9afe10 dc302800 dc46e910 80424e90 dc473c00 dc454f00
fe00: 000001b5 7f619d64 dcc7c830 00000000 00000000 dc9afe38 dc9afe68 00000000
fe20: 00000000 00000000 dc9afe28 dc9afe28 80424d80 00000000 00000035 9cac0034
fe40: 00000000 00000000 00000000 00000000 000001b5 00000000 00000000 00000000
fe60: dc9afe68 dc9afe10 3b9aca00 00000000 00000080 00000034 00000000 00000100
fe80: 00000000 00000000 dc9afe10 00000004 dc454a00 00000000 dc46e010 dc46e96c
fea0: dc46e000 dc46e964 00200200 00100100 dc46e910 7f619ec0 00000600 80c0e770
fec0: dc15a900 dcc7c838 00000000 dc46e954 8042d434 dcc44680 dc46e954 dc004400
fee0: dc454500 00000000 00000000 dc9ae038 dc004400 8003c450 dcc44680 dc004414
ff00: dc46e954 dc454500 00000001 dcc44680 dc004414 dcc44698 dc9ae000 dc9ae030
ff20: 00000001 dc9ae000 dc004400 8003d158 8003d020 00000000 00000000 80c53941
ff40: dc9aff64 dcb71ea0 00000000 dcc44680 8003d020 00000000 00000000 00000000
ff60: 00000000 80042480 00000000 00000000 000000f8 dcc44680 00000000 00000000
ff80: dc9aff80 dc9aff80 00000000 00000000 dc9aff90 dc9aff90 dc9affac dcb71ea0
ffa0: 800423cc 00000000 00000000 8000e018 00000000 00000000 00000000 00000000
ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<8001a6f8>] (v7_dma_clean_range+0x20/0x38) from [<800170fc>] (dma_cache_maint_page+0x50/0x54)
[<800170fc>] (dma_cache_maint_page+0x50/0x54) from [<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c)
[<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c) from [<80017238>] (arm_dma_map_page+0x64/0x68)
[<80017238>] (arm_dma_map_page+0x64/0x68) from [<80017588>] (arm_dma_map_sg+0x7c/0xf4)
[<80017588>] (arm_dma_map_sg+0x7c/0xf4) from [<80436f88>] (sdhci_send_command+0x894/0xe00)
[<80436f88>] (sdhci_send_command+0x894/0xe00) from [<80438c90>] (sdhci_request+0xc0/0x1ec)
[<80438c90>] (sdhci_request+0xc0/0x1ec) from [<80424cb4>] (mmc_start_request+0xb8/0xd4)
[<80424cb4>] (mmc_start_request+0xb8/0xd4) from [<80424de8>] (__mmc_start_req+0x60/0x84)
[<80424de8>] (__mmc_start_req+0x60/0x84) from [<80424e90>] (mmc_wait_for_req+0x10/0x20)
[<80424e90>] (mmc_wait_for_req+0x10/0x20) from [<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio])
[<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio]) from [<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio])
[<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio]) from [<8003c450>] (process_one_work+0x10c/0x370)
[<8003c450>] (process_one_work+0x10c/0x370) from [<8003d158>] (worker_thread+0x138/0x3fc)
[<8003d158>] (worker_thread+0x138/0x3fc) from [<80042480>] (kthread+0xb4/0xb8)
[<80042480>] (kthread+0xb4/0xb8) from [<8000e018>] (ret_from_fork+0x14/0x3c)
Code: e1a02312 e2423001 e1c00003 f57ff04f (ee070f3a)
---[ end trace 0c038f0b8e0b67a3 ]---
Kernel panic - not syncing: Fatal exception

Jason's analysis:

  "The GCC 4.8.1 compiler will not do the for-loop till scat_entries, instead,
   it only run one round loop. This may be caused by that the GCC 4.8.1 thought
   that the scat_list only have one item and then no need to do full iteration,
   but this is simply wrong by looking at the assebly code. This will cause the sg
   buffer not get set when scat_entries > 1 and thus lead to kernel panic.

   Note: This issue not observed with GCC 4.7.2, only found on the GCC 4.8.1)"

Fix this by using the normal [0] style for defining unknown number of list
entries following the struct. This also fixes corruption with scat_q_depth, which
was mistankely added to the end of struct and overwritten if there were more
than item in the scat list.
Reported-by: default avatarJason Liu <r64343@freescale.com>
Tested-by: default avatarJason Liu <r64343@freescale.com>
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      52235599
    • Hector Marco-Gisbert's avatar
      x86, mm/ASLR: Fix stack randomization on 64-bit systems · 5fb6f0aa
      Hector Marco-Gisbert authored 
      commit 4e7c22d4 upstream.

The issue is that the stack for processes is not properly randomized on
64 bit architectures due to an integer overflow.

The affected function is randomize_stack_top() in file
"fs/binfmt_elf.c":

  static unsigned long randomize_stack_top(unsigned long stack_top)
  {
           unsigned int random_variable = 0;

           if ((current->flags & PF_RANDOMIZE) &&
                   !(current->personality & ADDR_NO_RANDOMIZE)) {
                   random_variable = get_random_int() & STACK_RND_MASK;
                   random_variable <<= PAGE_SHIFT;
           }
           return PAGE_ALIGN(stack_top) + random_variable;
           return PAGE_ALIGN(stack_top) - random_variable;
  }

Note that, it declares the "random_variable" variable as "unsigned int".
Since the result of the shifting operation between STACK_RND_MASK (which
is 0x3fffff on x86_64, 22 bits) and PAGE_SHIFT (which is 12 on x86_64):

	  random_variable <<= PAGE_SHIFT;

then the two leftmost bits are dropped when storing the result in the
"random_variable". This variable shall be at least 34 bits long to hold
the (22+12) result.

These two dropped bits have an impact on the entropy of process stack.
Concretely, the total stack entropy is reduced by four: from 2^28 to
2^30 (One fourth of expected entropy).

This patch restores back the entropy by correcting the types involved
in the operations in the functions randomize_stack_top() and
stack_maxrandom_size().

The successful fix can be tested with:

  $ for i in `seq 1 10`; do cat /proc/self/maps | grep stack; done
  7ffeda566000-7ffeda587000 rw-p 00000000 00:00 0                          [stack]
  7fff5a332000-7fff5a353000 rw-p 00000000 00:00 0                          [stack]
  7ffcdb7a1000-7ffcdb7c2000 rw-p 00000000 00:00 0                          [stack]
  7ffd5e2c4000-7ffd5e2e5000 rw-p 00000000 00:00 0                          [stack]
  ...

Once corrected, the leading bytes should be between 7ffc and 7fff,
rather than always being 7fff.
Signed-off-by: default avatarHector Marco-Gisbert <hecmargi@upv.es>
Signed-off-by: default avatarIsmael Ripoll <iripoll@upv.es>
[ Rebased, fixed 80 char bugs, cleaned up commit message, added test example and CVE ]
Signed-off-by: default avatarKees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: CVE-2015-1593
Link: http://lkml.kernel.org/r/20150214173350.GA18393@www.outflux.netSigned-off-by: default avatarBorislav Petkov <bp@suse.de>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      5fb6f0aa
    • Thadeu Lima de Souza Cascardo's avatar
      blk-throttle: check stats_cpu before reading it from sysfs · 1c222f7b
      Thadeu Lima de Souza Cascardo authored 
      commit 045c47ca upstream.

When reading blkio.throttle.io_serviced in a recently created blkio
cgroup, it's possible to race against the creation of a throttle policy,
which delays the allocation of stats_cpu.

Like other functions in the throttle code, just checking for a NULL
stats_cpu prevents the following oops caused by that race.

[ 1117.285199] Unable to handle kernel paging request for data at address 0x7fb4d0020
[ 1117.285252] Faulting instruction address: 0xc0000000003efa2c
[ 1137.733921] Oops: Kernel access of bad area, sig: 11 [#1]
[ 1137.733945] SMP NR_CPUS=2048 NUMA PowerNV
[ 1137.734025] Modules linked in: bridge stp llc kvm_hv kvm binfmt_misc autofs4
[ 1137.734102] CPU: 3 PID: 5302 Comm: blkcgroup Not tainted 3.19.0 #5
[ 1137.734132] task: c000000f1d188b00 ti: c000000f1d210000 task.ti: c000000f1d210000
[ 1137.734167] NIP: c0000000003efa2c LR: c0000000003ef9f0 CTR: c0000000003ef980
[ 1137.734202] REGS: c000000f1d213500 TRAP: 0300   Not tainted  (3.19.0)
[ 1137.734230] MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI>  CR: 42008884  XER: 20000000
[ 1137.734325] CFAR: 0000000000008458 DAR: 00000007fb4d0020 DSISR: 40000000 SOFTE: 0
GPR00: c0000000003ed3a0 c000000f1d213780 c000000000c59538 0000000000000000
GPR04: 0000000000000800 0000000000000000 0000000000000000 0000000000000000
GPR08: ffffffffffffffff 00000007fb4d0020 00000007fb4d0000 c000000000780808
GPR12: 0000000022000888 c00000000fdc0d80 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 000001003e120200 c000000f1d5b0cc0 0000000000000200 0000000000000000
GPR24: 0000000000000001 c000000000c269e0 0000000000000020 c000000f1d5b0c80
GPR28: c000000000ca3a08 c000000000ca3dec c000000f1c667e00 c000000f1d213850
[ 1137.734886] NIP [c0000000003efa2c] .tg_prfill_cpu_rwstat+0xac/0x180
[ 1137.734915] LR [c0000000003ef9f0] .tg_prfill_cpu_rwstat+0x70/0x180
[ 1137.734943] Call Trace:
[ 1137.734952] [c000000f1d213780] [d000000005560520] 0xd000000005560520 (unreliable)
[ 1137.734996] [c000000f1d2138a0] [c0000000003ed3a0] .blkcg_print_blkgs+0xe0/0x1a0
[ 1137.735039] [c000000f1d213960] [c0000000003efb50] .tg_print_cpu_rwstat+0x50/0x70
[ 1137.735082] [c000000f1d2139e0] [c000000000104b48] .cgroup_seqfile_show+0x58/0x150
[ 1137.735125] [c000000f1d213a70] [c0000000002749dc] .kernfs_seq_show+0x3c/0x50
[ 1137.735161] [c000000f1d213ae0] [c000000000218630] .seq_read+0xe0/0x510
[ 1137.735197] [c000000f1d213bd0] [c000000000275b04] .kernfs_fop_read+0x164/0x200
[ 1137.735240] [c000000f1d213c80] [c0000000001eb8e0] .__vfs_read+0x30/0x80
[ 1137.735276] [c000000f1d213cf0] [c0000000001eb9c4] .vfs_read+0x94/0x1b0
[ 1137.735312] [c000000f1d213d90] [c0000000001ebb38] .SyS_read+0x58/0x100
[ 1137.735349] [c000000f1d213e30] [c000000000009218] syscall_exit+0x0/0x98
[ 1137.735383] Instruction dump:
[ 1137.735405] 7c6307b4 7f891800 409d00b8 60000000 60420000 3d420004 392a63b0 786a1f24
[ 1137.735471] 7d49502a e93e01c8 7d495214 7d2ad214 <7cead02a> e9090008 e9490010 e9290018

And here is one code that allows to easily reproduce this, although this
has first been found by running docker.

void run(pid_t pid)
{
	int n;
	int status;
	int fd;
	char *buffer;
	buffer = memalign(BUFFER_ALIGN, BUFFER_SIZE);
	n = snprintf(buffer, BUFFER_SIZE, "%d\n", pid);
	fd = open(CGPATH "/test/tasks", O_WRONLY);
	write(fd, buffer, n);
	close(fd);
	if (fork() > 0) {
		fd = open("/dev/sda", O_RDONLY | O_DIRECT);
		read(fd, buffer, 512);
		close(fd);
		wait(&status);
	} else {
		fd = open(CGPATH "/test/blkio.throttle.io_serviced", O_RDONLY);
		n = read(fd, buffer, BUFFER_SIZE);
		close(fd);
	}
	free(buffer);
	exit(0);
}

void test(void)
{
	int status;
	mkdir(CGPATH "/test", 0666);
	if (fork() > 0)
		wait(&status);
	else
		run(getpid());
	rmdir(CGPATH "/test");
}

int main(int argc, char **argv)
{
	int i;
	for (i = 0; i < NR_TESTS; i++)
		test();
	return 0;
}
Reported-by: default avatarRicardo Marin Matinata <rmm@br.ibm.com>
Signed-off-by: default avatarThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: default avatarJens Axboe <axboe@fb.com>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      1c222f7b
    • David Sterba's avatar
      btrfs: set proper message level for skinny metadata · a4954420
      David Sterba authored 
      commit 5efa0490 upstream.

This has been confusing people for too long, the message is really just
informative.
Signed-off-by: default avatarDavid Sterba <dsterba@suse.cz>
Signed-off-by: default avatarChris Mason <clm@fb.com>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      a4954420
    • Chen Jie's avatar
      jffs2: fix handling of corrupted summary length · 8d3d232f
      Chen Jie authored 
      commit 164c2406 upstream.

sm->offset maybe wrong but magic maybe right, the offset do not have CRC.

Badness at c00c7580 [verbose debug info unavailable]
NIP: c00c7580 LR: c00c718c CTR: 00000014
REGS: df07bb40 TRAP: 0700   Not tainted  (2.6.34.13-WR4.3.0.0_standard)
MSR: 00029000 <EE,ME,CE>  CR: 22084f84  XER: 00000000
TASK = df84d6e0[908] 'mount' THREAD: df07a000
GPR00: 00000001 df07bbf0 df84d6e0 00000000 00000001 00000000 df07bb58 00000041
GPR08: 00000041 c0638860 00000000 00000010 22084f88 100636c8 df814ff8 00000000
GPR16: df84d6e0 dfa558cc c05adb90 00000048 c0452d30 00000000 000240d0 000040d0
GPR24: 00000014 c05ae734 c05be2e0 00000000 00000001 00000000 00000000 c05ae730
NIP [c00c7580] __alloc_pages_nodemask+0x4d0/0x638
LR [c00c718c] __alloc_pages_nodemask+0xdc/0x638
Call Trace:
[df07bbf0] [c00c718c] __alloc_pages_nodemask+0xdc/0x638 (unreliable)
[df07bc90] [c00c7708] __get_free_pages+0x20/0x48
[df07bca0] [c00f4a40] __kmalloc+0x15c/0x1ec
[df07bcd0] [c01fc880] jffs2_scan_medium+0xa58/0x14d0
[df07bd70] [c01ff38c] jffs2_do_mount_fs+0x1f4/0x6b4
[df07bdb0] [c020144c] jffs2_do_fill_super+0xa8/0x260
[df07bdd0] [c020230c] jffs2_fill_super+0x104/0x184
[df07be00] [c0335814] get_sb_mtd_aux+0x9c/0xec
[df07be20] [c033596c] get_sb_mtd+0x84/0x1e8
[df07be60] [c0201ed0] jffs2_get_sb+0x1c/0x2c
[df07be70] [c0103898] vfs_kern_mount+0x78/0x1e8
[df07bea0] [c0103a58] do_kern_mount+0x40/0x100
[df07bec0] [c011fe90] do_mount+0x240/0x890
[df07bf10] [c0120570] sys_mount+0x90/0xd8
[df07bf40] [c00110d8] ret_from_syscall+0x0/0x4

=== Exception: c01 at 0xff61a34
    LR = 0x100135f0
Instruction dump:
38800005 38600000 48010f41 4bfffe1c 4bfc2d15 4bfffe8c 72e90200 4082fc28
3d20c064 39298860 8809000d 68000001 <0f000000> 2f800000 419efc0c 38000001
mount: mounting /dev/mtdblock3 on /common failed: Input/output error
Signed-off-by: default avatarChen Jie <chenjie6@huawei.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      8d3d232f
    • Daniel J Blueman's avatar
      EDAC, amd64_edac: Prevent OOPS with >16 memory controllers · 9a8120f5
      Daniel J Blueman authored 
      commit 0c510cc8 upstream.

When DRAM errors occur on memory controllers after EDAC_MAX_MCS (16),
the kernel fatally dereferences unallocated structures, see splat below;
this occurs on at least NumaConnect systems.

Fix by checking if a memory controller info structure was found.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000320
IP: [<ffffffff819f714f>] decode_bus_error+0x2f/0x2b0
PGD 2f8b5a3067 PUD 2f8b5a2067 PMD 0
Oops: 0000 [#2] SMP
Modules linked in:
CPU: 224 PID: 11930 Comm: stream_c.exe.gn Tainted: G   D    3.19.0 #1
Hardware name: Supermicro H8QGL/H8QGL, BIOS 3.5b    01/28/2015
task: ffff8807dbfb8c00 ti: ffff8807dd16c000 task.ti: ffff8807dd16c000
RIP: 0010:[<ffffffff819f714f>] [<ffffffff819f714f>] decode_bus_error+0x2f/0x2b0
RSP: 0000:ffff8907dfc03c48 EFLAGS: 00010297
RAX: 0000000000000001 RBX: 9c67400010080a13 RCX: 0000000000001dc6
RDX: 000000001dc61dc6 RSI: ffff8907dfc03df0 RDI: 000000000000001c
RBP: ffff8907dfc03ce8 R08: 0000000000000000 R09: 0000000000000022
R10: ffff891fffa30380 R11: 00000000001cfc90 R12: 0000000000000008
R13: 0000000000000000 R14: 000000000000001c R15: 00009c6740001000
FS: 00007fa97ee18700(0000) GS:ffff8907dfc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000320 CR3: 0000003f889b8000 CR4: 00000000000407e0
Stack:
 0000000000000000 ffff8907dfc03df0 0000000000000008 9c67400010080a13
 000000000000001c 00009c6740001000 ffff8907dfc03c88 ffffffff810e4f9a
 ffff8907dfc03ce8 ffffffff81b375b9 0000000000000000 0000000000000010
Call Trace:
 <IRQ>
 ? vprintk_default
 ? printk
 amd_decode_mce
 notifier_call_chain
 atomic_notifier_call_chain
 mce_log
 machine_check_poll
 mce_timer_fn
 ? mce_cpu_restart
 call_timer_fn.isra.29
 run_timer_softirq
 __do_softirq
 irq_exit
 smp_apic_timer_interrupt
 apic_timer_interrupt
 <EOI>
 ? down_read_trylock
 __do_page_fault
 ? __schedule
 do_page_fault
 page_fault
Signed-off-by: default avatarDaniel J Blueman <daniel@numascale.com>
Link: http://lkml.kernel.org/r/1424144078-24589-1-git-send-email-daniel@numascale.com
[ Boris: massage commit message ]
Signed-off-by: default avatarBorislav Petkov <bp@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz> [backport to 3.12]
      9a8120f5
    • Tomáš Hodek's avatar
      md/raid1: fix read balance when a drive is write-mostly. · 8107488c
      Tomáš Hodek authored 
      commit d1901ef0 upstream.

When a drive is marked write-mostly it should only be the
target of reads if there is no other option.

This behaviour was broken by

commit 9dedf603
    md/raid1: read balance chooses idlest disk for SSD

which causes a write-mostly device to be *preferred* is some cases.

Restore correct behaviour by checking and setting
best_dist_disk and best_pending_disk rather than best_disk.

We only need to test one of these as they are both changed
from -1 or >=0 at the same time.

As we leave min_pending and best_dist unchanged, any non-write-mostly
device will appear better than the write-mostly device.
Reported-by: default avatarTomáš Hodek <tomas.hodek@volny.cz>
Reported-by: default avatarDark Penguin <darkpenguin@yandex.ru>
Signed-off-by: default avatarNeilBrown <neilb@suse.de>
Link: http://marc.info/?l=linux-raid&m=135982797322422
Fixes: 9dedf603Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      8107488c
    • NeilBrown's avatar
      md/raid5: Fix livelock when array is both resyncing and degraded. · ca39d6db
      NeilBrown authored 
      commit 26ac1073 upstream.

Commit a7854487:
  md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.

Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.

Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.

So change the condition to only force RCW on non-degraded arrays.
Reported-by: default avatarManibalan P <pmanibalan@amiindia.co.in>
Bisected-by: default avatarJes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: default avatarJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: default avatarNeilBrown <neilb@suse.de>
Fixes: a7854487Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      ca39d6db
    • James Hogan's avatar
      metag: Fix KSTK_EIP() and KSTK_ESP() macros · 5ce0984a
      James Hogan authored 
      commit c2996cb2 upstream.

The KSTK_EIP() and KSTK_ESP() macros should return the user program
counter (PC) and stack pointer (A0StP) of the given task. These are used
to determine which VMA corresponds to the user stack in
/proc/<pid>/maps, and for the user PC & A0StP in /proc/<pid>/stat.

However for Meta the PC & A0StP from the task's kernel context are used,
resulting in broken output. For example in following /proc/<pid>/maps
output, the 3afff000-3b021000 VMA should be described as the stack:

  # cat /proc/self/maps
  ...
  100b0000-100b1000 rwxp 00000000 00:00 0          [heap]
  3afff000-3b021000 rwxp 00000000 00:00 0

And in the following /proc/<pid>/stat output, the PC is in kernel code
(1074234964 = 0x40078654) and the A0StP is in the kernel heap
(1335981392 = 0x4fa17550):

  # cat /proc/self/stat
  51 (cat) R ... 1335981392 1074234964 ...

Fix the definitions of KSTK_EIP() and KSTK_ESP() to use
task_pt_regs(tsk)->ctx rather than (tsk)->thread.kernel_context. This
gets the registers from the user context stored after the thread info at
the base of the kernel stack, which is from the last entry into the
kernel from userland, regardless of where in the kernel the task may
have been interrupted, which results in the following more correct
/proc/<pid>/maps output:

  # cat /proc/self/maps
  ...
  0800b000-08070000 r-xp 00000000 00:02 207        /lib/libuClibc-0.9.34-git.so
  ...
  100b0000-100b1000 rwxp 00000000 00:00 0          [heap]
  3afff000-3b021000 rwxp 00000000 00:00 0          [stack]

And /proc/<pid>/stat now correctly reports the PC in libuClibc
(134320308 = 0x80190b4) and the A0StP in the [stack] region (989864576 =
0x3b002280):

  # cat /proc/self/stat
  51 (cat) R ... 989864576 134320308 ...
Reported-by: default avatarAlexey Brodkin <Alexey.Brodkin@synopsys.com>
Reported-by: default avatarVineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: default avatarJames Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      5ce0984a
    • Jan Kara's avatar
      xfs: Fix quota type in quota structures when reusing quota file · a776835f
      Jan Kara authored 
      commit dfcc70a8 upstream.

For filesystems without separate project quota inode field in the
superblock we just reuse project quota file for group quotas (and vice
versa) if project quota file is allocated and we need group quota file.
When we reuse the file, quota structures on disk suddenly have wrong
type stored in d_flags though. Nobody really cares about this (although
structure type reported to userspace was wrong as well) except
that after commit 14bf61ff (quota: Switch ->get_dqblk() and
->set_dqblk() to use bytes as space units) assertion in
xfs_qm_scall_getquota() started to trigger on xfs/106 test (apparently I
was testing without XFS_DEBUG so I didn't notice when submitting the
above commit).

Fix the problem by properly resetting ddq->d_flags when running quotacheck
for a quota file.
Reported-by: default avatarAl Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: default avatarJan Kara <jack@suse.cz>
Reviewed-by: default avatarDave Chinner <dchinner@redhat.com>
Signed-off-by: default avatarDave Chinner <david@fromorbit.com>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      a776835f
    • Nicolas Saenz Julienne's avatar
      gpio: tps65912: fix wrong container_of arguments · 22fd0313
      Nicolas Saenz Julienne authored 
      commit 2f97c20e upstream.

The gpio_chip operations receive a pointer the gpio_chip struct which is
contained in the driver's private struct, yet the container_of call in those
functions point to the mfd struct defined in include/linux/mfd/tps65912.h.
Signed-off-by: default avatarNicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      22fd0313
    • Hans Holmberg's avatar
      gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node · dddaecc2
      Hans Holmberg authored 
      commit 9cf75e9e upstream.

The change:

7b8792bb
gpiolib: of: Correct error handling in of_get_named_gpiod_flags

assumed that only one gpio-chip is registred per of-node.
Some drivers register more than one chip per of-node, so
adjust the matching function of_gpiochip_find_and_xlate to
not stop looking for chips if a node-match is found and
the translation fails.

Fixes: 7b8792bb ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags")
Signed-off-by: default avatarHans Holmberg <hans.holmberg@intel.com>
Acked-by: default avatarAlexandre Courbot <acourbot@nvidia.com>
Tested-by: default avatarRobert Jarzmik <robert.jarzmik@free.fr>
Tested-by: default avatarTyler Hall <tylerwhall@gmail.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      dddaecc2
    • Catalin Marinas's avatar
      arm64: compat Fix siginfo_t -> compat_siginfo_t conversion on big endian · 59e4cc3e
      Catalin Marinas authored 
      commit 9d42d48a upstream.

The native (64-bit) sigval_t union contains sival_int (32-bit) and
sival_ptr (64-bit). When a compat application invokes a syscall that
takes a sigval_t value (as part of a larger structure, e.g.
compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t
union is converted to the native sigval_t with sival_int overlapping
with either the least or the most significant half of sival_ptr,
depending on endianness. When the corresponding signal is delivered to a
compat application, on big endian the current (compat_uptr_t)sival_ptr
cast always returns 0 since sival_int corresponds to the top part of
sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int
is copied to the compat_siginfo_t structure.
Reported-by: default avatarBamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Tested-by: default avatarBamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Signed-off-by: default avatarCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      59e4cc3e
    • Martin Vajnar's avatar
      hx4700: regulator: declare full constraints · dada8422
      Martin Vajnar authored 
      commit a52d2093 upstream.

Since the removal of CONFIG_REGULATOR_DUMMY option, the touchscreen stopped
working. This patch enables the "replacement" for REGULATOR_DUMMY and
allows the touchscreen to work even though there is no regulator for "vcc".
Signed-off-by: default avatarMartin Vajnar <martin.vajnar@gmail.com>
Signed-off-by: default avatarRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      dada8422
    • Marcelo Tosatti's avatar
      KVM: x86: update masterclock values on TSC writes · 5202b358
      Marcelo Tosatti authored 
      commit 7f187922 upstream.

When the guest writes to the TSC, the masterclock TSC copy must be
updated as well along with the TSC_OFFSET update, otherwise a negative
tsc_timestamp is calculated at kvm_guest_time_update.

Once "if (!vcpus_matched && ka->use_master_clock)" is simplified to
"if (ka->use_master_clock)", the corresponding "if (!ka->use_master_clock)"
becomes redundant, so remove the do_request boolean and collapse
everything into a single condition.
Signed-off-by: default avatarMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      5202b358
    • Ilya Dryomov's avatar
      libceph: fix double __remove_osd() problem · 8ef0cf0e
      Ilya Dryomov authored 
      commit 7eb71e03 upstream.

It turns out it's possible to get __remove_osd() called twice on the
same OSD.  That doesn't sit well with rb_erase() - depending on the
shape of the tree we can get a NULL dereference, a soft lockup or
a random crash at some point in the future as we end up touching freed
memory.  One scenario that I was able to reproduce is as follows:

            <osd3 is idle, on the osd lru list>
<con reset - osd3>
con_fault_finish()
  osd_reset()
                              <osdmap - osd3 down>
                              ceph_osdc_handle_map()
                                <takes map_sem>
                                kick_requests()
                                  <takes request_mutex>
                                  reset_changed_osds()
                                    __reset_osd()
                                      __remove_osd()
                                  <releases request_mutex>
                                <releases map_sem>
    <takes map_sem>
    <takes request_mutex>
    __kick_osd_requests()
      __reset_osd()
        __remove_osd() <-- !!!

A case can be made that osd refcounting is imperfect and reworking it
would be a proper resolution, but for now Sage and I decided to fix
this by adding a safe guard around __remove_osd().

Fixes: http://tracker.ceph.com/issues/8087

Cc: Sage Weil <sage@redhat.com>
Signed-off-by: default avatarIlya Dryomov <idryomov@gmail.com>
Reviewed-by: default avatarSage Weil <sage@redhat.com>
Reviewed-by: default avatarAlex Elder <elder@linaro.org>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      8ef0cf0e
    • Ilya Dryomov's avatar
      libceph: change from BUG to WARN for __remove_osd() asserts · 27f9c180
      Ilya Dryomov authored 
      commit cc9f1f51 upstream.

No reason to use BUG_ON for osd request list assertions.
Signed-off-by: default avatarIlya Dryomov <idryomov@redhat.com>
Reviewed-by: default avatarAlex Elder <elder@linaro.org>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      27f9c180
    • Ilya Dryomov's avatar
      libceph: assert both regular and lingering lists in __remove_osd() · 66d37e92
      Ilya Dryomov authored 
      commit 7c6e6fc5 upstream.

It is important that both regular and lingering requests lists are
empty when the OSD is removed.
Signed-off-by: default avatarIlya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: default avatarAlex Elder <elder@linaro.org>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      66d37e92
    • Anantha Krishnan's avatar
      Bluetooth: Add support for Acer [0489:e078] · ebf03336
      Anantha Krishnan authored 
      commit 4b552bc9 upstream.

Add support for the QCA6174 chip.

    T:  Bus=06 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
    D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
    P:  Vendor=0489 ProdID=e078 Rev=00.01
    C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
    I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: default avatarAnantha Krishnan <ananthk@codeaurora.org>
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      ebf03336
  9. 02 Mar, 2015 1 commit
    • James Hogan's avatar
      KVM: MIPS: Don't leak FPU/DSP to guest · 48f80a96
      James Hogan authored 
      [ Upstream commit f798217d ]

The FPU and DSP are enabled via the CP0 Status CU1 and MX bits by
kvm_mips_set_c0_status() on a guest exit, presumably in case there is
active state that needs saving if pre-emption occurs. However neither of
these bits are cleared again when returning to the guest.

This effectively gives the guest access to the FPU/DSP hardware after
the first guest exit even though it is not aware of its presence,
allowing FP instructions in guest user code to intermittently actually
execute instead of trapping into the guest OS for emulation. It will
then read & manipulate the hardware FP registers which technically
belong to the user process (e.g. QEMU), or are stale from another user
process. It can also crash the guest OS by causing an FP exception, for
which a guest exception handler won't have been registered.

First lets save and disable the FPU (and MSA) state with lose_fpu(1)
before entering the guest. This simplifies the problem, especially for
when guest FPU/MSA support is added in the future, and prevents FR=1 FPU
state being live when the FR bit gets cleared for the guest, which
according to the architecture causes the contents of the FPU and vector
registers to become UNPREDICTABLE.

We can then safely remove the enabling of the FPU in
kvm_mips_set_c0_status(), since there should never be any active FPU or
MSA state to save at pre-emption, which should plug the FPU leak.

DSP state is always live rather than being lazily restored, so for that
it is simpler to just clear the MX bit again when re-entering the guest.
Signed-off-by: default avatarJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # v3.10+: 044f0f03: MIPS: KVM: Deliver guest interrupts
Cc: <stable@vger.kernel.org> # v3.10+: 3ce465e0: MIPS: Export FP functions used by lose_fpu(1) for KVM
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: default avatarJames Hogan <james.hogan@imgtec.com>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      48f80a96
  11. 01 Mar, 2015 1 commit
    • Alexey Brodkin's avatar
      ARC: fix page address calculation if PAGE_OFFSET != LINUX_LINK_BASE · 02c76a9a
      Alexey Brodkin authored 
      commit 06f34e1c upstream.

We used to calculate page address differently in 2 cases:

1. In virt_to_page(x) we do
 --->8---
 mem_map + (x - CONFIG_LINUX_LINK_BASE) >> PAGE_SHIFT
 --->8---

2. In in pte_page(x) we do
 --->8---
 mem_map + (pte_val(x) - PAGE_OFFSET) >> PAGE_SHIFT
 --->8---

That leads to problems in case PAGE_OFFSET != CONFIG_LINUX_LINK_BASE -
different pages will be selected depending on where and how we calculate
page address.

In particular in the STAR 9000853582 when gdb attempted to read memory
of another process it got improper page in get_user_pages() because this
is exactly one of the places where we search for a page by pte_page().

The fix is trivial - we need to calculate page address similarly in both
cases.
Signed-off-by: default avatarAlexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: default avatarVineet Gupta <vgupta@synopsys.com>
Signed-off-by: default avatarJiri Slaby <jslaby@suse.cz>
      02c76a9a
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7