* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Fix build errors in sc-mips.c

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  x86: avoid high BIOS area when allocating address space
  x86: avoid E820 regions when allocating address space
  x86: avoid low BIOS area when allocating address space
  resources: add arch hook for preventing allocation in reserved areas
  Revert "resources: support allocating space within a region from the top down"
  Revert "PCI: allocate bus resources from the top down"
  Revert "x86/PCI: allocate space from the end of a region, not the beginning"
  Revert "x86: allocate space within a region top-down"
  Revert "PCI: fix pci_bus_alloc_resource() hang, prefer positive decode"
  PCI: Update MCP55 quirk to not affect non HyperTransport variants

Seen with malta_defconfig on Linus' tree:

  CC      arch/mips/mm/sc-mips.o
arch/mips/mm/sc-mips.c: In function 'mips_sc_is_activated':
arch/mips/mm/sc-mips.c:77: error: 'config2' undeclared (first use in this function)
arch/mips/mm/sc-mips.c:77: error: (Each undeclared identifier is reported only once
arch/mips/mm/sc-mips.c:77: error: for each function it appears in.)
arch/mips/mm/sc-mips.c:81: error: 'tmp' undeclared (first use in this function)
make[2]: *** [arch/mips/mm/sc-mips.o] Error 1
make[1]: *** [arch/mips/mm] Error 2
make: *** [arch/mips] Error 2

[Ralf: Cosmetic changes to minimize the number of arguments passed to
mips_sc_is_activated]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1752/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This prevents allocation of the last 2MB before 4GB.

The experiment described here shows Windows 7 ignoring the last 1MB:
https://bugzilla.kernel.org/show_bug.cgi?id=23542#c27

This patch ignores the top 2MB instead of just 1MB because H. Peter Anvin
says "There will be ROM at the top of the 32-bit address space; it's a fact
of the architecture, and on at least older systems it was common to have a
shadow 1 MiB below."
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

When we allocate address space, e.g., to assign it to a PCI device, don't
allocate anything mentioned in the BIOS E820 memory map.

On recent machines (2008 and newer), we assign PCI resources from the
windows described by the ACPI PCI host bridge _CRS.  On many Dell
machines, these windows overlap some E820 reserved areas, e.g.,

    BIOS-e820: 00000000bfe4dc00 - 00000000c0000000 (reserved)
    pci_root PNP0A03:00: host bridge window [mem 0xbff00000-0xdfffffff]

If we put devices at 0xbff00000, they don't work, probably because
that's really RAM, not I/O memory.  This patch prevents that by removing
the 0xbfe4dc00-0xbfffffff area from the "available" resource.

I'm not very happy with this solution because Windows solves the problem
differently (it seems to ignore E820 reserved areas and it allocates
top-down instead of bottom-up; details at comment 45 of the bugzilla
below).  That means we're vulnerable to BIOS defects that Windows would not
trip over.  For example, if BIOS described a device in ACPI but didn't
mention it in E820, Windows would work fine but Linux would fail.

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This implements arch_remove_reservations() so allocate_resource() can
avoid any arch-specific reserved areas.  This currently just avoids the
BIOS area (the first 1MB), but could be used for E820 reserved areas if
that turns out to be necessary.

We previously avoided this area in pcibios_align_resource().  This patch
moves the test from that PCI-specific path to a generic path, so *all*
resource allocations will avoid this area.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This adds arch_remove_reservations(), which an arch can implement if it
needs to protect part of the address space from allocation.

Sometimes that can be done by just putting a region in the resource tree,
but there are cases where that doesn't work well.  For example, x86 BIOS
E820 reservations are not related to devices, so they may overlap part of,
all of, or more than a device resource, so they may not end up at the
correct spot in the resource tree.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This reverts commit e7f8567d.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This reverts commit b126b470.

We're going back to the old behavior of allocating from bus resources
in _CRS order.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This reverts commit dc9887dc.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This reverts commit 1af3c2e4.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This reverts commit 82e3e767.

We're going back to considering bus resources in the order we found
them (in _CRS order, when we're using _CRS), so we don't need to
define any ordering.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

* 'for_linus' of git://github.com/at91linux/linux-2.6-at91:
  at91: Refactor Stamp9G20 and PControl G20 board file
  at91: Fix uhpck clock rate in upll case

* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: Fix preemption counter leak in kvm_timer_init()
  KVM: enlarge number of possible CPUID leaves
  KVM: SVM: Do not report xsave in supported cpuid
  KVM: Fix OSXSAVE after migration

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Runtime: Fix pm_runtime_suspended()
  PM / Hibernate: Restore old swap signature to avoid user space breakage
  PM / Hibernate: Fix PM_POST_* notification with user-space suspend

* 'bkl_removal' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] uvcvideo: Convert to unlocked_ioctl
  [media] uvcvideo: Lock stream mutex when accessing format-related information
  [media] uvcvideo: Move mmap() handler to uvc_queue.c
  [media] uvcvideo: Move mutex lock/unlock inside uvc_free_buffers
  [media] uvcvideo: Lock controls mutex when querying menus
  [media] v4l2-dev: fix race condition
  [media] V4L: improve the BKL replacement heuristic
  [media] v4l2-dev: use mutex_lock_interruptible instead of plain mutex_lock
  [media] cx18: convert to unlocked_ioctl
  [media] radio-timb: convert to unlocked_ioctl
  [media] sh_vou: convert to unlocked_ioctl
  [media] cafe_ccic: replace ioctl by unlocked_ioctl
  [media] et61x251_core: trivial conversion to unlocked_ioctl
  [media] sn9c102: convert to unlocked_ioctl
  [media] BKL: trivial ioctl -> unlocked_ioctl video driver conversions
  [media] typhoon: convert to unlocked_ioctl
  [media] si4713: convert to unlocked_ioctl
  [media] tea5764: convert to unlocked_ioctl
  [media] cadet: use unlocked_ioctl
  [media] BKL: trivial BKL removal from V4L2 radio drivers

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix conflict of Mic Boot controls
  ALSA: HDA: Enable subwoofer on Asus G73Jw
  ALSA: HDA: Fix auto-mute on Lenovo Edge 14
  ASoC: Fix bias power down of non-DAPM codec
  ASoC: WM8580: Fix R8 initial value
  ASoC: fix deemphasis control in wm8904/55/60 codecs

Due to the recent change for multiple mics assignment, we need to handle
the index of each Mic Boost control respectively.  Otherwise the driver
gets the control element conflicts, and gives the unsable state.

Reference: kernel bug 25002
	https://bugzilla.kernel.org/show_bug.cgi?id=25002Reported-and-tested-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

As PControl G20 is a carrier board for the Stamp9G20 SoM, some code can
be shared. Therefore board-stamp9g20.c is refactored to allow reusing the
SoM initialization and board-pcontrol-g20.c is modified to use it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The uhpck clock should be divided from the utmi clock, not its parent
(main). This change is mostly cosmetic as the uhpck rate value is not
used anywhere except for the debugfs clock output.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

* 'for-linus' of git://git.infradead.org/users/eparis/notify:
  fanotify: fill in the metadata_len field on struct fanotify_event_metadata
  fanotify: split version into version and metadata_len
  fanotify: Dont try to open a file descriptor for the overflow event
  fanotify: Introduce FAN_NOFD
  fanotify: do not leak user reference on allocation failure
  inotify: stop kernel memory leak on file creation failure
  fanotify: on group destroy allow all waiters to bypass permission check
  fanotify: Dont allow a mask of 0 if setting or removing a mark
  fanotify: correct broken ref counting in case adding a mark failed
  fanotify: if set by user unset FMODE_NONOTIFY before fsnotify_perm() is called
  fanotify: remove packed from access response message
  fanotify: deny permissions when no event was sent

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (28 commits)
  MIPS: Add a CONFIG_FORCE_MAX_ZONEORDER Kconfig option.
  MIPS: LD/SD o32 macro GAS fix update
  MIPS: Alchemy: fix build with SERIAL_8250=n
  MIPS: Rename mips_dma_cache_sync back to dma_cache_sync
  MIPS: MT: Fix typo in comment.
  SSB: Fix nvram_get on BCM47xx platform
  MIPS: BCM47xx: Swap serial console if ttyS1 was specified.
  MIPS: BCM47xx: Use sscanf for parsing mac address
  MIPS: BCM47xx: Fill values for b43 into SSB sprom
  MIPS: BCM47xx: Do not read config from CFE
  MIPS: FDT size is a be32
  MIPS: Fix CP0 COUNTER clockevent race
  MIPS: Fix regression on BCM4710 processor detection
  MIPS: JZ4740: Fix pcm device name
  MIPS: Separate two consecutive loads in memset.S
  MIPS: Send proper signal and siginfo on FP emulator faults.
  MIPS: AR7: Fix loops per jiffies on TNETD7200 devices
  MIPS: AR7: Fix double ar7_gpio_init declaration
  MIPS: Rework GENERIC_HARDIRQS Kconfig.
  MIPS: Alchemy: Add return value check for strict_strtoul()
  ...

I wrote this quirk awhile ago to properly setup MCP55 chips on hypertransport
busses so that interrupts reached whatever cpu happend to boot the kdump kernel.
while that works well, it was recently shown to me that a a non-hypertransport
variant of the MCP55 exists, and on those system the register that this quirk
manipulates causes hangs if you write to it.  Since the quirk was only meant to
handle errors found on MCP55 chips that have a HT interface, this patch adds a
filter to make sure the chip is an HT capable before making the needed register
adjustment.  This lets the broken MCP55s work with kdump while not breaking the
non-HT variants.

Resolves https://bugzilla.kernel.org/show_bug.cgi?id=23952

Tested successfully by the reporter and myself.

Cc: stable@kernel.org
Reported-by: Mathieu Bérard <mathieu@mberard.eu>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

For huge page support with base page size of 16K or 32K, we have to
increase the MAX_ORDER so that huge pages can be allocated.

[Ralf: I don't think a user should have to configure obscure constants like
this but for the time being this will have to suffice.]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1685/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

I am about to commit:

http://sourceware.org/ml/binutils/2010-10/msg00033.html

that fixes a problem with the LD/SD macro currently implemented by GAS for
the o32 ABI in an inconsistent way.  This is best illustrated with a
simple program, which I'm copying here from the message above for easier
reference:

$ cat ld.s
	ld	$5,32767($4)
	ld	$5,32768($4)

This gets assebled into the following output:

$ mips-linux-as -32 -mips3 -o ld.o ld.s
$ mips-linux-objdump -d ld.o

ld.o:     file format elf32-tradbigmips

Disassembly of section .text:

00000000 <.text>:
   0:	dc857fff 	ld	a1,32767(a0)
   4:	3c010001 	lui	at,0x1
   8:	00810821 	addu	at,a0,at
   c:	8c258000 	lw	a1,-32768(at)
  10:	8c268004 	lw	a2,-32764(at)
	...

Oops!

 The GAS fix makes the macro behave in a consistent way and pairs of LW/SW
instructions to be output as appropriate regardless of the size of the
offset associated with the address used.  The machine instruction is still
available, but to reach it macros have to be disabled first.  This has a
side effect of requiring the use of a machine-addressable memory operand.

 As some platforms require 64-bit operations for accesses to some I/O
registers LD/SD instructions are used in a couple of places in Linux
regardless of the ABI selected.  Here's a fix for some pieces of code
affected I've been able to track down.  The fix should be backwards
compatible with all supported binutils releases in existence and can be
used as a reference for any other places or off-tree code.  The use of the
"R" constraint guarantees a machine-addressable operand.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1680/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

In commit 7d172bfe ("Alchemy: Add UART PM methods") I introduced
platform PM methods which call a function of the 8250 driver;
this patch works around link failures when the kernel is built
without 8250 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1737/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This fixes IP22 and IP28 build errors.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The nvram_get function was never in the mainline kernel, it only existed in
an external OpenWrt patch. Use nvram_getenv function, which is in mainline
and use an include instead of an extra function declaration.  et0macaddr
contains the mac address in text from like 00:11:22:33:44:55. We have to
parse it before adding it into macaddr.

nvram_parse_macaddr will be merged into asm/mach-bcm47xx/nvram.h through
the MIPS git tree and will be available soon. It will not build now without
nvram_parse_macaddr, but it hasn't before either.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: mb@bu3sch.de
Cc: netdev@vger.kernel.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Buesch <mb@bu3sch.de>
Patchwork: https://patchwork.linux-mips.org/patch/1849/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Some devices like the Netgear WGT634U are using ttyS1 for default console
output. We should switch to that console if it was given in the kernel_args
parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1848/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Instead of writing own function for parsing the mac address we now
use sscanf.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1847/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Fill the sprom with all available values from the nvram. Most of these
new values are needed for the b43 or b43legacy driver.

Parts of this patch have been in OpenWRT for a long time and were written
by Michael Buesch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1846/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The config options read out here are not stored in CFE but only in NVRAM on
the devices. Remove reading from CFE and only access the NVRAM.  Reading out
CFE does not harm but is useless here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1845/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The totalsize field was be32. And the reserve bootmem would cause failure.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
To: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Dezhong Diao <dediao@cisco.com>
Patchwork: https://patchwork.linux-mips.org/patch/1838/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Consider the following test case:

write_c0_compare(read_c0_count());

Even if the counter doesn't increment during execution, this might not
generate an interrupt until the counter wraps around.  The CPU may
perform the comparison each time CP0 COUNT increments, not when CP0
COMPARE is written.

If mips_next_event() is called with a very small delta, and CP0 COUNT
increments during the calculation of "cnt += delta", it is possible
that CP0 COMPARE will be written with the current value of CP0 COUNT.
If this is detected, the function should return -ETIME, to indicate
that the interrupt might not have actually gotten scheduled.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1836/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

BCM4710 uses the BMIPS32 core (like BCM6345), not the MIPS 4Kc core as
was previously believed.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Alexandros C. Couloumbis <alex@ozo.com>
Patchwork: https://patchwork.linux-mips.org/patch/1837/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

As part the ASoC multi-component patch (commit f0fba2ad) the jz4740 pcm
driver was renamed to 'jz4740-pcm-audio'. Adjust the device name
accordingly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1770/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

partial_fixup is used in noreorder block.

Separating two consecutive loads can save one cycle on processors with
GPR intrelock and can fix load-use on processors that need a load delay slot.

Also do so for fwd_fixup.

[Ralf: Only R2000/R3000 class processors are lacking the the load-user
interlock and even some of those got it retrofitted.  With R2000/R3000
being fairly uncommon these days the impact of this bug should be minor.]
Signed-off-by: Tony Wu <tung7970@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1768/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>