On systems where there is MMIO space between different blocks of RAM in
the physical address space, __ioremap_caller did not allow mapping these
MMIO areas, because they were below the end RAM and thus considered RAM
as well.  Use the memblock-based page_is_ram function, which returns
false for such MMIO holes.

v2:
  Keep the check for p < virt_to_phys(high_memory). On 32-bit systems
  with high memory (memory above physical address 4GiB), the high memory
  is expected to be available though ioremap. The high_memory variable
  marks the end of low memory; comparing against it means that only
  ioremap requests for low RAM will be denied.
  Reported by Michael Ellerman.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

To support accurate checking for different blocks of memory on PPC32,
use the same memblock-based approach that's already used on PPC64 also
on PPC32.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Instead of open-coding the search in page_is_ram, call memblock_is_memory.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The Wii has a blue LED in the disk drive slot, which is controlled via a
GPIO line. Add this LED to wii.dts, and mark it as a panic-indicator.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

These are the GPIO line names on a Nintendo Wii, as documented in:
https://wiibrew.org/wiki/Hardware/Hollywood_GPIOsSigned-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The Hollywood GPIO controller supports 32 GPIOs, but on the Wii, only 24
are used.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The Hollywood chipset's GPIO controller has two sets of registers: One
for access by the PowerPC CPU, and one for access by the ARM coprocessor
(but both are accessible from the PPC because the memory firewall
(AHBPROT) is usually disabled when booting Linux, today).

The wii_power_off function currently assumes that the poweroff GPIO pin
is configured for use via the ARM side, but the upcoming GPIO driver
configures all pins for use via the PPC side, breaking poweroff.

Configure the owner register explicitly in wii_power_off to make
wii_power_off work with and without the new GPIO driver.

I think the Wii can be switched to the generic gpio-poweroff driver,
after the GPIO driver is merged.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Previously, wii_device_probe would only initialize devices under the
/hollywood node. After this patch, platform devices placed outside of
/hollywood will also be initialized.

The intended usecase for this are devices located outside of the
Hollywood chip, such as GPIO LEDs and GPIO buttons.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On 64-bit Book3E systems, in setup_tlb_core_data() we reference other
CPUs pacas. But in commit 59f57774 ("powerpc/64: Defer paca
allocation until memory topology is discovered") the allocation of
non-boot-CPU pacas was deferred until later in boot.

This leads to an oops:

  CPU maps initialized for 1 thread per core
  Unable to handle kernel paging request for data at address 0x8888888888888918
  Faulting instruction address: 0xc000000000e2f0d0
  Oops: Kernel access of bad area, sig: 11 [#1]
  NIP .setup_tlb_core_data+0xdc/0x160
  Call Trace:
    .setup_tlb_core_data+0x5c/0x160 (unreliable)
    .setup_arch+0x80/0x348
    .start_kernel+0x7c/0x598
    start_here_common+0x1c/0x40

Luckily setup_tlb_core_data() is called immediately prior to
smp_setup_pacas(). So simply switching their order is sufficient to
fix the oops and seems unlikely to have any other unwanted side
effects.

Fixes: 59f57774 ("powerpc/64: Defer paca allocation until memory topology is discovered")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

SLOF checks for 'sc 1' (hypercall) support by issuing a hcall with
H_SET_DABR. Since the recent commit e8ebedbf ("KVM: PPC: Book3S
HV: Return error from h_set_dabr() on POWER9") changed H_SET_DABR to
return H_UNSUPPORTED on Power9, we see guest boot failures, the
symptom is the boot seems to just stop in SLOF, eg:

  SLOF ***************************************************************
  QEMU Starting
   Build Date = Sep 24 2017 12:23:07
   FW Version = buildd@ release 20170724
  <no further output>

SLOF can cope if H_SET_DABR returns H_HARDWARE. So wwitch the return
value to H_HARDWARE instead of H_UNSUPPORTED so that we don't break
the guest boot.

That does mean we return a different error to PowerVM in this case,
but that's probably not a big concern.

Fixes: e8ebedbf ("KVM: PPC: Book3S HV: Return error from h_set_dabr() on POWER9")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Bring in yet another series that touches KVM code, and might need to
be merged into the kvm-ppc branch to resolve conflicts.

This required some changes in pnv_power9_force_smt4_catch/release()
due to the paca array becomming an array of pointers.

We need to zero-out pgd table only if we share the slab cache with
pud/pmd level caches. With the support of 4PB, we don't share the slab
cache anymore. Instead of removing the code completely hide it within
an #ifdef. We don't need to do this with any other page table level,
because they all allocate table of double the size and we take of
initializing the first half corrrectly during page table zap.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Consolidate multiple #if / #ifdef into one]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch increases the max virtual (effective) address value to 4PB.
With 4K page size config we continue to limit ourself to 64TB.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Keep the H_PGTABLE_RANGE test, update it to work]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

For addresses above 512TB we allocate additional mmu contexts. To make
it all easy, addresses above 512TB are handled with IR/DR=1 and with
stack frame setup.

The mmu_context_t is also updated to track the new extended_ids. To
support upto 4PB we need a total 8 contexts.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Minor formatting tweaks and comment wording, switch BUG to WARN
      in get_ea_context().]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In a following patch, on finding a free area we will need to do
allocatinon of extra contexts as needed. Consolidating the return path
for slice_get_unmapped_area() will make that easier.

Split into a separate patch to make review easy.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Memory keys are supported only with hash translation mode. Instead of
using #ifdef in generic code move the key related pte bits to
respective headers
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We should zero an array using sizeof instead of number of elements.

Fixes the following compiler (GCC 7.3.0) warnings:

drivers/macintosh/rack-meter.c: In function 'rackmeter_do_pause':
drivers/macintosh/rack-meter.c:157:2: warning: 'memset' used with length equal to number of elements without multiplication by element size [-Wmemset-elt-size]
drivers/macintosh/rack-meter.c:158:2: warning: 'memset' used with length equal to number of elements without multiplication by element size [-Wmemset-elt-size]

Fixes: 4f7bef7a ("drivers: macintosh: rack-meter: fix bogus memsets")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

asm/barrier.h is not always included after asm/synch.h, which meant
it was missing __SUBARCH_HAS_LWSYNC, so in some files smp_wmb() would
be eieio when it should be lwsync. kernel/time/hrtimer.c is one case.

__SUBARCH_HAS_LWSYNC is only used in one place, so just fold it in
to where it's used. Previously with my small simulator config, 377
instances of eieio in the tree. After this patch there are 55.

Fixes: 46d075be ("powerpc: Optimise smp_wmb")
Cc: stable@vger.kernel.org # v2.6.29+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[mpe: Add missing ';' to make it compile]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

thread_pkey_regs_init() initializes the pkey related registers
instead of initializing the fields in the task structures.  Fortunately
those key related registers are re-set to zero when the task
gets scheduled on the cpu. However its good to fix this glaringly
visible error.

Fixes: 06bb53b3 ("powerpc: store and restore the pkey state across context switches")
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Michael Ellerman reported the following call trace when running
ftracetest:

  BUG: using __this_cpu_write() in preemptible [00000000] code: ftracetest/6178
  caller is opt_pre_handler+0xc4/0x110
  CPU: 1 PID: 6178 Comm: ftracetest Not tainted 4.15.0-rc7-gcc6x-gb2cd1df6 #1
  Call Trace:
  [c0000000f9ec39c0] [c000000000ac4304] dump_stack+0xb4/0x100 (unreliable)
  [c0000000f9ec3a00] [c00000000061159c] check_preemption_disabled+0x15c/0x170
  [c0000000f9ec3a90] [c000000000217e84] opt_pre_handler+0xc4/0x110
  [c0000000f9ec3af0] [c00000000004cf68] optimized_callback+0x148/0x170
  [c0000000f9ec3b40] [c00000000004d954] optinsn_slot+0xec/0x10000
  [c0000000f9ec3e30] [c00000000004bae0] kretprobe_trampoline+0x0/0x10

This is showing up since OPTPROBES is now enabled with CONFIG_PREEMPT.

trampoline_probe_handler() considers itself to be a special kprobe
handler for kretprobes. In doing so, it expects to be called from
kprobe_handler() on a trap, and re-enables preemption before returning a
non-zero return value so as to suppress any subsequent processing of the
trap by the kprobe_handler().

However, with optprobes, we don't deal with special handlers (we ignore
the return code) and just try to re-enable preemption causing the above
trace.

To address this, modify trampoline_probe_handler() to not be special.
The only additional processing done in kprobe_handler() is to emulate
the instruction (in this case, a 'nop'). We adjust the value of
regs->nip for the purpose and delegate the job of re-enabling
preemption and resetting current kprobe to the probe handlers
(kprobe_handler() or optimized_callback()).

Fixes: 8a2d71a3 ("powerpc/kprobes: Disable preemption before invoking probe handler for optprobes")
Cc: stable@vger.kernel.org # v4.15+
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

No change to object files.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

opal_nvram_write currently just assumes success if it encounters an
error other than OPAL_BUSY or OPAL_BUSY_EVENT. Have it return -EIO
on other errors instead.

Fixes: 628daa8d ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The H_CPU_BEHAV_* flags should be checked for in the 'behaviour' field
of 'struct h_cpu_char_result' -- 'character' is for H_CPU_CHAR_*
flags.

Found by playing around with QEMU's implementation of the hypercall:

  H_CPU_CHAR=0xf000000000000000
  H_CPU_BEHAV=0x0000000000000000

  This clears H_CPU_BEHAV_FAVOUR_SECURITY and H_CPU_BEHAV_L1D_FLUSH_PR
  so pseries_setup_rfi_flush() disables 'rfi_flush'; and it also
  clears H_CPU_CHAR_L1D_THREAD_PRIV flag. So there is no RFI flush
  mitigation at all for cpu_show_meltdown() to report; but currently
  it does:

  Original kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/meltdown
    Mitigation: RFI Flush

  Patched kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/meltdown
    Not affected

  H_CPU_CHAR=0x0000000000000000
  H_CPU_BEHAV=0xf000000000000000

  This sets H_CPU_BEHAV_BNDS_CHK_SPEC_BAR so cpu_show_spectre_v1() should
  report vulnerable; but currently it doesn't:

  Original kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/spectre_v1
    Not affected

  Patched kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/spectre_v1
    Vulnerable
Brown-paper-bag-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: f636c147 ("powerpc/pseries: Set or clear security feature flags")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Move __map_kernel_page_nid() inside #ifdef SPARSEMEM_VMEMMAP]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Try to allocate kernel page tables for direct mapping and vmemmap
according to the node of the memory they will map. The node is not
available for the linear map in early boot, so use range allocation
to allocate the page tables from the region they map, which is
effectively node-local.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix build error in radix__create_section_mapping()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Per-node allocations are possible on 64s with radix that does
not have the bolted SLB limitation.

Hash would be able to do the same if all CPUs had the bottom of
their node-local memory bolted as well. This is left as an
exercise for the reader.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add dummy definition of boot_cpuid for !SMP]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Rename the dummy allocate_pacas() to fix 32-bit build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Build an array that finds hardware CPU number from logical CPU
number in firmware CPU discovery. Use that rather than setting
paca of other CPUs directly, to begin with. Subsequent patch will
not have pacas allocated at this point.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix SMP=n build by adding #ifdef in arch_match_cpu_phys_id()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Move this into the early setup code, and don't iterate over CPU masks.
We don't want to call into sysfs so early from setup, and a future patch
won't initialize CPU masks by the time this is called.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fold in incremental fix from Nick for DSCR handling]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Split sparsemem initialisation from basic numa topology discovery.
Move the parsing earlier in boot, before pacas are allocated.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This will be used by powerpc to allocate per-cpu stacks and other
data structures node-local where possible.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop stray change to memblock_alloc_range() as noticed by akpm]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

slb_shadow structures are avoided for radix environment.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We no longer allocate lppacas in an array, so this patch removes the
1kB static alignment for the structure, and enforces the PAPR
alignment requirements at allocation time. We can not reduce the 1kB
allocation size however, due to existing KVM hypervisors.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Change the paca array into an array of pointers to pacas. Allocate
pacas individually.

This allows flexibility in where the PACAs are allocated. Future work
will allocate them node-local. Platforms that don't have address limits
on PACAs would be able to defer PACA allocations until later in boot
rather than allocate all possible ones up-front then freeing unused.

This is slightly more overhead (one additional indirection) for cross
CPU paca references, but those aren't too common.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The "lppaca" is a structure registered with the hypervisor. This is
unnecessary when running on non-virtualised platforms. One field from
the lppaca (pmcregs_in_use) is also used by the host, so move the host
part out into the paca (lppaca field is still updated in
guest mode).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix non-pseries build with some #ifdefs]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In mpic_physmask() we loop over all CPUs up to 32, then get the hard
SMP processor id of that CPU.

Currently that's possibly walking off the end of the paca array, but
in a future patch we will change the paca array to be an array of
pointers, and in that case we will get a NULL for missing CPUs and
oops. eg:

  Unable to handle kernel paging request for data at address 0x88888888888888b8
  Faulting instruction address: 0xc00000000004e380
  Oops: Kernel access of bad area, sig: 11 [#1]
  ...
  NIP .mpic_set_affinity+0x60/0x1a0
  LR  .irq_do_set_affinity+0x48/0x100

Fix it by checking the CPU is possible, this also fixes the code if
there are gaps in the CPU numbering which probably never happens on
mpic systems but who knows.
Debugged-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>