It's disabled by default and the data mapping is supposed to be
retrieved from the attached panel driver in mainline.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

VDDD is supplied by VCC_1P8 on HB2.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Trivial formatting change.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use proper gpio flag definitions for GPIOs rather than using opaque
uninformative numbers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix the SD card detect signal, which was missing the polarity
specification, and the pull-up necessary for proper signalling.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Broadcom Wi-Fi was moved out to a separate include file.  Add the
include.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move the microsom includes into the .dts files.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rename microsom include to imx6qdl-sr-som.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the AR8035 include, the file is now gone.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for the Hummingboard Gate and Edge devices from
SolidRun.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These device trees add support for the TS-4600 by Technologic Systems.

More details here:
  http://wiki.embeddedarm.com/wiki/TS-4600Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the documentation for the TS-4600 by Technologic Systems.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These device trees add support for TS-7970 by Technologic Systems.

More details here:
   https://wiki.embeddedarm.com/wiki/TS-7970Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the documentation for the TS-7970 by Technologic Systems.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the Computer on Module Colibri iMX7D 1GB along
with the Colibri Evaluation Board device trees. Follow the usual
hierarchic include model, maintaining shared configuration in
imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Colibri Evaluation Carrier Board provides a MCP2515 CAN
controller connected via SPI. Note that the i.MX 7 provides
an internal CAN controller which is much better suited for CAN
operations. Using the MCP2515 with a Colibri iMX7 module is
mainly useful to test the SPI interface.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Colibri standard defines SODIMM 71 as backlight enable
GPIO. Assign the GPIO to the backlight node in the module
level device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The usdhc1 controller instance is used to provide the default
SD/MMC capabilities of the Colibri standard. The IO pins are
supplied to the SoC on the module whereas the SD-card is powered
by the Carrier Board supply.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Specify CPU supply using the "cpu-supply" property instead of
the invalid "arm-supply" property.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All Colibri iMX7 SKUs use either single-die NAND or eMMC, hence
NAND_CE1 is not used on the module and can be used as a GPIO by
carrier boards.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use pull-ups instead of pull-downs for the pins which are already
pulled-up externally.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Colibri pins PWM<A> and <D> are multiplexed on the module, make
sure the secondary SoC pin is not active.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Colibri default which enables USB Host power is not necessarily
tied to the OTG2 controller, some carrier board use the pin to
control USB power for both controllers. Hence name the pinctrl
group more generic.

Also move the regulator to the generic eval-v3 device tree since
the regulator is always on the carrier board. In the Colibri iMX7S
case the regulator is just not used.  This allows to reuse the
regulator in a upcoming SKU Colibri iMX7D 1GB with eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.

So pass the "sii,43wvf1g" compatible string which describes the parallel
LCD.

Also, pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place regulators inside "simple-bus", so move
them out.

The motivation for doing this is to make it easier to adding new
regulators.
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.

So pass the "sii,43wvf1g" compatible string, which describes the parallel
LCD.

Also pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All Toradex Carrier Boards use a st,m41t0 compatible RTC. Compared
to a st,m41t00 this RTC has also an oscillator fail bit which allows
to detect when the RTC lost track of time.

Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This avoids the warning

  hw perfevents: no interrupt-affinity property for /pmu, guessing.
Signed-off-by: Esben Haabendal <eha@deif.com>
[RV: adapt commit log to the warning emitted in current mainline]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add usb2 and usb3 labels to USB2 and USB3 controller device tree nodes,
for easier modification in board dts files.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LS1021A can be reset via the dcfg regmap in the same way as the
arm64 layerscape SoCs, so add the corresponding DT node.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The USB PHYs are supplied via MC13892 VUSB regulator rail,
so properly describe this in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

device_type = "pci" should be used for the SoC level PCI controller and
it is already present at imx6qdl.dtsi.

Remove it from the subnode in order to fix the following build
warnings with W=1:

arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing ranges for PCI bridge (or not a bridge)
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing bus-range for PCI bridge
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (unit_address_format): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:

arch/arm/boot/dts/imx6ul-14x14-evk.dtb: Warning (simple_bus_reg): Node /regulators/sd1_regulator missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the unneeded unit address for the i2cmux nodes in order to fix
the following build warnings with W=1:

arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@3 has a unit name, but no reg property

While at it, rename the i2cmux nodes and subnodes to make it clearer to which
i2c controller the mux belongs to.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the unneeded unit address for the port nodes in order to fix
the following build warnings with W=1:

arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a0000/tc358743@f/port@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@0 has a unit name, but no reg property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:

arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name

Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:

arch/arm/boot/dts/imx6q-apalis-eval.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move disp0 node from soc node to root node.

disp0 node does not have any register properties and thus
shouldn't be placed on the bus.

This fixes the following build warnings with W=1:

arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (simple_bus_reg): Node /soc/disp0 missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:

arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit name, but no reg property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>