Some firmware revisions don't notify host about
self-bss-peer removal until after associated vdev
is deleted. This has been observed with qca6174
WLAN.RM.2.0-00073 firmware.

This patch fixes AP teardown slowdowns and
prevents delays and warnings:

 ath10k_pci 0000:00:05.0: failed to remove peer for AP vdev 0: -110
 ath10k_pci 0000:00:05.0: removing stale peer xx:xx:xx:xx:xx:xx from vdev_id 0
 ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 24
 ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 8
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The value was off by one.  The error probably has no negative
affect on any upstream firmware, but should be fixed anyway
in case it comes into use in the future.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Fix spelling error.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

A bit of general cleanup to make debug messages more useful.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In case firmware fails to start the scan, then complete
the start condition and clean up so that driver does not
block on timeout.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Major changes in ath10k:

* add support for qca6174 hardware
* enable RX batching to reduce CPU load

Merge tag 'iwlwifi-next-for-kalle-2015-02-03' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

* Add support for beamforming
* Enable stuck queue detection for iwlmvm
* A few fixes for EBS scan
* Fixes for various failure paths
* Improvements for TDLS Offchannel

The functions brcmu_pkt_buf_free_skb() and usb_free_urb() test whether
their argument is NULL and then return immediately. Thus the test around
the call is not needed.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The relay_close() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The functions kfree() and release_firmware() were called in a few cases
by the cw1200_load_firmware_cw1200() function during error handling even if
the passed variables contained still a null pointer.

Corresponding implementation details could be improved by adjustments for
jump targets.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This is only an API consolidation to make things more readable.
Instances of  HZ / CONST  are replaced by appropriate msecs_to_jiffies().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.

The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.

This patch partially reverts the commit 1846ac3d ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().

I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.

Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.

CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Fixes: 1846ac3d ("ath5k: Use usleep_range where possible")
Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Set the transmit rate for the keep-alive frames
as 1M/CCK when the current channel is in the
2GHz band.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Chips in the AR9003 family have a second TSF, which
needs to be cleared when putting the card to
sleep.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Setting the required configuration in the PCIE
WorkAround register needs to be done after all the
WoW parameters have been set.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch addresses several issues with the
ath9k_hw_wow_enable() routine:

* The usage of set/clr variables is removed. Writing
  the required values to registers is cleaner.

* The shift value of 28 for the contention window field
  in AR_WOW_PATTERN is incorrect, change it to 27.

* Disabling Keep Alive needs to be done based on the
  LINK_CHANGE option. This is done unconditionally now,
  fix this.

* The workaround for the D1/D3 issue is required only
  for AR9462.

* The bitfield for enabling pattern matching for packets
  less than 256 bytes has expanded for new chips, handle
  this accordingly.

* General cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Since the number of user patterns is higher for
newer chips, make sure that this is registered
during initialization.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Newer chips like WB222, WB335 support more than
8 user-configurable patterns. This patch adds
support for it by setting up the correct HW
registers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This driver utilizes a FIFO buffer for RX descriptors. There are four places
in the code where it calculates the number of free slots. Several of those
locations do the calculation incorrectly. To fix these and to prevent future
mistakes, a common inline routine is created.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The hardware and firmware for the RTL8192EE utilize a FIFO list of
descriptors. There were some problems with the initial implementation.
The worst of these failed to detect that the FIFO was becoming full,
which led to the device needing to be power cycled. As this condition
is not relevant to most of the devices supported by rtlwifi, a callback
routine was added to detect this situation. This patch implements the
necessary changes in the pci handler, and the linkage into the appropriate
rtl8192ee routine.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The 3.2 revision has a different target BMI
version so it wasn't recognized by ath10k (despite
the chip_id rev being on the supported list
already).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Introduce an optional log level configuration for the existing debugfs fw_dbglog file. It
allows users to configure the desired log level for firmware dbglog messages.

To configure log level as WARN:

echo 0xffffffff  2 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog

The values are:

VERBOSE		0
INFO		1
WARN		2
ERR		3
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Otherwise ath10k will just checksum everything even if it did not
go through the TCP/IP stack (for example bridged frames). In the worst
case this could mean recreating the checksum for incorrect data.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This should fix a very rare occurrence of the following deadlock:

  [<ffffffffa018265e>] ath10k_wmi_tx_beacons_nowait+0x1e/0x50 [ath10k_core]
  [<ffffffffa01829b6>] ath10k_wmi_op_ep_tx_credits+0x16/0x40 [ath10k_core]
  [<ffffffffa017d685>] ath10k_htc_send+0x285/0x3d0 [ath10k_core]
  [<ffffffffa0184b81>] ath10k_wmi_cmd_send_nowait+0x81/0x110 [ath10k_core]
  [<ffffffffa0184c61>] ath10k_wmi_tx_beacon_nowait.part.33+0x51/0x90 [ath10k_core]
  [<ffffffffa0184cd0>] ath10k_wmi_tx_beacons_iter+0x30/0x40 [ath10k_core]
  [<ffffffff81882246>] __iterate_active_interfaces+0xa6/0x100
  [<ffffffffa0184ca0>] ? ath10k_wmi_tx_beacon_nowait.part.33+0x90/0x90 [ath10k_core]
  [<ffffffff818822ae>] ieee80211_iterate_active_interfaces_atomic+0xe/0x10
  [<ffffffffa0182676>] ath10k_wmi_tx_beacons_nowait+0x36/0x50 [ath10k_core]
  [<ffffffffa01829b6>] ath10k_wmi_op_ep_tx_credits+0x16/0x40 [ath10k_core]
  [<ffffffffa017d140>] ath10k_htc_rx+0x280/0x410 [ath10k_core]
  [<ffffffffa01bcbf0>] ? ath10k_ce_completed_recv_next+0x60/0x80 [ath10k_pci]
  [<ffffffffa01bc6ab>] ath10k_pci_ce_recv_data+0x11b/0x1d0 [ath10k_pci]
  [<ffffffffa01bcf44>] ath10k_ce_per_engine_service+0x64/0xc0 [ath10k_pci]
  [<ffffffffa01bcfc2>] ath10k_ce_per_engine_service_any+0x22/0x50 [ath10k_pci]
  [<ffffffffa01bc4d0>] ath10k_pci_tasklet+0x30/0x90 [ath10k_pci]
  [<ffffffff81055a55>] tasklet_action+0xc5/0x100

To prevent this make sure to release ar->data_lock
while calling to ath10k_wmi_beacon_send_ref_nowait().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The command logic shouldn't really care about
arvif structure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Ath10k driver sets wrong default key idx that results in
sending unicast frames with multicast key.

The reason for this behavior is that cached broadcast key
is installed for station MAC address on association. After
dot1x completes, unicast key is installed for station
MAC address. Default key idx is set to broadcast key id when
driver tries to send broadcast frame. This causes firmware
to use broadcast key id to transmit unicast frames to stations.

Used TX_USAGE flag to set default key for stations.

Added callback for setting unicast default idx which will be
invoked on every default key idx configuration.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Current implementation depends on msm-bus driver which
is not merged into mainline kernel therefore
this code is removed
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Print (at debug level) all cipher and AKM suites
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Print Tx descriptors
Print ring index for all Tx related messages
Sort prefixes: Tx for transmit, TxC for completion, added "D"
for descriptor related prints
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use spinlock, this should not impact Tx as lock is always free
except for de-allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Non-cacheable Tx descriptor for the last fragment of
multi-fragment frame used to be written back twice.

Refactor code to always write non-cacheable descriptor
only once
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In the Tx, work around used to force destination index 0
to be used. This is no more necessary, as firmware supports
multiple destinations
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Since the maximum number of configurable patterns
is chip-specific, use the HW capability instead
of a fixed value for checking if a free pattern
slot is available.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

* Remove unnecessary comments.
* Remove unused macros.
* Indent the macros.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>