Drivers such as sja1105 and stmmac that call xpcs_create() expects an
error returned by the pcs-xpcs module, but this was not the case on
failed to allocate memory.

Fixed this by returning an -ENOMEM instead of a NULL pointer.

Fixes: 3ad1d171 ("net: dsa: sja1105: migrate to xpcs for SGMII")
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210810085812.1808466-1-vee.khee.wong@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

After migrating my laptop from 4.19-LTS to 5.4-LTS a while ago I noticed
that my Ethernet port to which a bond and a VLAN interface are attached
appeared to remain up after resuming from suspend with the cable unplugged
(and that problem still persists with 5.10-LTS).

It happens that the following happens:

  - the network driver (e1000e here) prepares to suspend, calls e1000e_down()
    which calls netif_carrier_off() to signal that the link is going down.
  - netif_carrier_off() adds a link_watch event to the list of events for
    this device
  - the device is completely stopped.
  - the machine suspends
  - the cable is unplugged and the machine brought to another location
  - the machine is resumed
  - the queued linkwatch events are processed for the device
  - the device doesn't yet have the __LINK_STATE_PRESENT bit and its events
    are silently dropped
  - the device is resumed with its link down
  - the upper VLAN and bond interfaces are never notified that the link had
    been turned down and remain up
  - the only way to provoke a change is to physically connect the machine
    to a port and possibly unplug it.

The state after resume looks like this:
  $ ip -br li | egrep 'bond|eth'
  bond0            UP             e8:6a:64:64:64:64 <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP>
  eth0             DOWN           e8:6a:64:64:64:64 <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP>
  eth0.2@eth0      UP             e8:6a:64:64:64:64 <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP>

Placing an explicit call to netdev_state_change() either in the suspend
or the resume code in the NIC driver worked around this but the solution
is not satisfying.

The issue in fact really is in link_watch that loses events while it
ought not to. It happens that the test for the device being present was
added by commit 124eee3f ("net: linkwatch: add check for netdevice
being present to linkwatch_do_dev") in 4.20 to avoid an access to
devices that are not present.

Instead of dropping events, this patch proceeds slightly differently by
postponing their handling so that they happen after the device is fully
resumed.

Fixes: 124eee3f ("net: linkwatch: add check for netdevice being present to linkwatch_do_dev")
Link: https://lists.openwall.net/netdev/2018/03/15/62
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210809160628.22623-1-w@1wt.euSigned-off-by: Jakub Kicinski <kuba@kernel.org>

I got a memleak report:

BUG: memory leak
unreferenced object 0x607ee521a658 (size 240):
comm "syz-executor.0", pid 955, jiffies 4294780569 (age 16.449s)
hex dump (first 32 bytes, cpu 1):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000d830ea5a>] br_multicast_add_port+0x1c2/0x300 net/bridge/br_multicast.c:1693
[<00000000274d9a71>] new_nbp net/bridge/br_if.c:435 [inline]
[<00000000274d9a71>] br_add_if+0x670/0x1740 net/bridge/br_if.c:611
[<0000000012ce888e>] do_set_master net/core/rtnetlink.c:2513 [inline]
[<0000000012ce888e>] do_set_master+0x1aa/0x210 net/core/rtnetlink.c:2487
[<0000000099d1cafc>] __rtnl_newlink+0x1095/0x13e0 net/core/rtnetlink.c:3457
[<00000000a01facc0>] rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3488
[<00000000acc9186c>] rtnetlink_rcv_msg+0x369/0xa10 net/core/rtnetlink.c:5550
[<00000000d4aabb9c>] netlink_rcv_skb+0x134/0x3d0 net/netlink/af_netlink.c:2504
[<00000000bc2e12a3>] netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
[<00000000bc2e12a3>] netlink_unicast+0x4a0/0x6a0 net/netlink/af_netlink.c:1340
[<00000000e4dc2d0e>] netlink_sendmsg+0x789/0xc70 net/netlink/af_netlink.c:1929
[<000000000d22c8b3>] sock_sendmsg_nosec net/socket.c:654 [inline]
[<000000000d22c8b3>] sock_sendmsg+0x139/0x170 net/socket.c:674
[<00000000e281417a>] ____sys_sendmsg+0x658/0x7d0 net/socket.c:2350
[<00000000237aa2ab>] ___sys_sendmsg+0xf8/0x170 net/socket.c:2404
[<000000004f2dc381>] __sys_sendmsg+0xd3/0x190 net/socket.c:2433
[<0000000005feca6c>] do_syscall_64+0x37/0x90 arch/x86/entry/common.c:47
[<000000007304477d>] entry_SYSCALL_64_after_hwframe+0x44/0xae

On error path of br_add_if(), p->mcast_stats allocated in
new_nbp() need be freed, or it will be leaked.

Fixes: 1080ab95 ("net: bridge: add support for IGMP/MLD stats and export them via netlink")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210809132023.978546-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

net: switchdev: zero-initialize struct switchdev_notifier_fdb_info emitted by drivers towards the bridge

The blamed commit added a new field to struct switchdev_notifier_fdb_info,
but did not make sure that all call paths set it to something valid.
For example, a switchdev driver may emit a SWITCHDEV_FDB_ADD_TO_BRIDGE
notifier, and since the 'is_local' flag is not set, it contains junk
from the stack, so the bridge might interpret those notifications as
being for local FDB entries when that was not intended.

To avoid that now and in the future, zero-initialize all
switchdev_notifier_fdb_info structures created by drivers such that all
newly added fields to not need to touch drivers again.

Fixes: 2c4eca3e ("net: bridge: switchdev: include local flag in FDB notifications")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20210810115024.1629983-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ignore fdb flags when adding port extern learn entries and always set
BR_FDB_LOCAL flag when adding bridge extern learn entries. This is
closest to the behaviour we had before and avoids breaking any use cases
which were allowed.

This patch fixes iproute2 calls which assume NUD_PERMANENT and were
allowed before, example:
$ bridge fdb add 00:11:22:33:44:55 dev swp1 extern_learn

Extern learn entries are allowed to roam, but do not expire, so static
or dynamic flags make no sense for them.

Also add a comment for future reference.

Fixes: eb100e0e ("net: bridge: allow to add externally learned entries from user-space")
Fixes: 0541a629 ("net: bridge: validate the NUD_PERMANENT bit when adding an extern_learn FDB entry")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210810110010.43859-1-razor@blackwall.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
bpf 2021-08-10

We've added 5 non-merge commits during the last 2 day(s) which contain
a total of 7 files changed, 27 insertions(+), 15 deletions(-).

1) Fix missing bpf_read_lock_trace() context for BPF loader progs, from Yonghong Song.

2) Fix corner case where BPF prog retrieves wrong local storage, also from Yonghong Song.

3) Restrict availability of BPF write_user helper behind lockdown, from Daniel Borkmann.

4) Fix multiple kernel-doc warnings in BPF core, from Randy Dunlap.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf, core: Fix kernel-doc notation
  bpf: Fix potentially incorrect results with bpf_get_local_storage()
  bpf: Add missing bpf_read_[un]lock_trace() for syscall program
  bpf: Add lockdown check for probe_write_user helper
  bpf: Add _kernel suffix to internal lockdown_bpf_read
====================

Link: https://lore.kernel.org/r/20210810144025.22814-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
Fix broken backpressure during FDB dump in DSA drivers

rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).

When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.

Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.

DSA is one of the few switchdev drivers that have an .ndo_fdb_dump
implementation, because of the assumption that the hardware and software
FDBs cannot be efficiently kept in sync via SWITCHDEV_FDB_ADD_TO_BRIDGE.
Other drivers with a home-cooked .ndo_fdb_dump implementation are
ocelot and dpaa2-switch. These appear to do the correct thing, as do the
other DSA drivers, so nothing else appears to need fixing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).

When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.

Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.

Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.

Fixes: 291d1e72 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).

When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.

Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.

Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.

Fixes: 58c59ef9 ("net: dsa: lantiq: Add Forwarding Database access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).

When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.

Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.

Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.

Fixes: ab335349 ("net: dsa: lan9303: Add port_fast_age and port_fdb_dump methods")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).

When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.

Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.

Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.

Fixes: e4b27ebc ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix kernel-doc warnings in kernel/bpf/core.c (found by scripts/kernel-doc
and W=1 builds). That is, correct a function name in a comment and add
return descriptions for 2 functions.

Fixes these kernel-doc warnings:

  kernel/bpf/core.c:1372: warning: expecting prototype for __bpf_prog_run(). Prototype was for ___bpf_prog_run() instead
  kernel/bpf/core.c:1372: warning: No description found for return value of '___bpf_prog_run'
  kernel/bpf/core.c:1883: warning: No description found for return value of 'bpf_prog_select_runtime'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210809215229.7556-1-rdunlap@infradead.org

Fix the data-race reported by syzbot [1]
Issue here is that igmp_ifc_timer_expire() can update in_dev->mr_ifc_count
while another change just occured from another context.

in_dev->mr_ifc_count is only 8bit wide, so the race had little
consequences.

[1]
BUG: KCSAN: data-race in igmp_ifc_event / igmp_ifc_timer_expire

write to 0xffff8881051e3062 of 1 bytes by task 12547 on cpu 0:
 igmp_ifc_event+0x1d5/0x290 net/ipv4/igmp.c:821
 igmp_group_added+0x462/0x490 net/ipv4/igmp.c:1356
 ____ip_mc_inc_group+0x3ff/0x500 net/ipv4/igmp.c:1461
 __ip_mc_join_group+0x24d/0x2c0 net/ipv4/igmp.c:2199
 ip_mc_join_group_ssm+0x20/0x30 net/ipv4/igmp.c:2218
 do_ip_setsockopt net/ipv4/ip_sockglue.c:1285 [inline]
 ip_setsockopt+0x1827/0x2a80 net/ipv4/ip_sockglue.c:1423
 tcp_setsockopt+0x8c/0xa0 net/ipv4/tcp.c:3657
 sock_common_setsockopt+0x5d/0x70 net/core/sock.c:3362
 __sys_setsockopt+0x18f/0x200 net/socket.c:2159
 __do_sys_setsockopt net/socket.c:2170 [inline]
 __se_sys_setsockopt net/socket.c:2167 [inline]
 __x64_sys_setsockopt+0x62/0x70 net/socket.c:2167
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff8881051e3062 of 1 bytes by interrupt on cpu 1:
 igmp_ifc_timer_expire+0x706/0xa30 net/ipv4/igmp.c:808
 call_timer_fn+0x2e/0x1d0 kernel/time/timer.c:1419
 expire_timers+0x135/0x250 kernel/time/timer.c:1464
 __run_timers+0x358/0x420 kernel/time/timer.c:1732
 run_timer_softirq+0x19/0x30 kernel/time/timer.c:1745
 __do_softirq+0x12c/0x26e kernel/softirq.c:558
 invoke_softirq kernel/softirq.c:432 [inline]
 __irq_exit_rcu+0x9a/0xb0 kernel/softirq.c:636
 sysvec_apic_timer_interrupt+0x69/0x80 arch/x86/kernel/apic/apic.c:1100
 asm_sysvec_apic_timer_interrupt+0x12/0x20 arch/x86/include/asm/idtentry.h:638
 console_unlock+0x8e8/0xb30 kernel/printk/printk.c:2646
 vprintk_emit+0x125/0x3d0 kernel/printk/printk.c:2174
 vprintk_default+0x22/0x30 kernel/printk/printk.c:2185
 vprintk+0x15a/0x170 kernel/printk/printk_safe.c:392
 printk+0x62/0x87 kernel/printk/printk.c:2216
 selinux_netlink_send+0x399/0x400 security/selinux/hooks.c:6041
 security_netlink_send+0x42/0x90 security/security.c:2070
 netlink_sendmsg+0x59e/0x7c0 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:703 [inline]
 sock_sendmsg net/socket.c:723 [inline]
 ____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
 ___sys_sendmsg net/socket.c:2446 [inline]
 __sys_sendmsg+0x1ed/0x270 net/socket.c:2475
 __do_sys_sendmsg net/socket.c:2484 [inline]
 __se_sys_sendmsg net/socket.c:2482 [inline]
 __x64_sys_sendmsg+0x42/0x50 net/socket.c:2482
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x01 -> 0x02

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 12539 Comm: syz-executor.1 Not tainted 5.14.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
ksz8795 VLAN fixes

This series fixes a number of bugs in the ksz8795 driver that affect
VLAN filtering, tag insertion, and tag removal.

I've tested these on the KSZ8795CLXD evaluation board, and checked the
register usage against the datasheets for the other supported chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The magic number 4 in VLAN table lookup was the number of entries we
can read and write at once.  Using phy_port_cnt here doesn't make
sense and presumably broke VLAN filtering for 3-port switches.  Change
it back to 4.

Fixes: 4ce2a984 ("net: dsa: microchip: ksz8795: use phy_port_cnt ...")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently ksz8_port_vlan_filtering() sets or clears the VLAN Enable
hardware flag.  That controls discarding of packets with a VID that
has not been enabled for any port on the switch.

Since it is a global flag, set the dsa_switch::vlan_filtering_is_global
flag so that the DSA core understands this can't be controlled per
port.

When VLAN filtering is enabled, the switch should also discard packets
with a VID that's not enabled on the ingress port.  Set or clear each
external port's VLAN Ingress Filter flag in ksz8_port_vlan_filtering()
to make that happen.

Fixes: e66f840c ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the CPU port, we can support both tagged and untagged VLANs at the
same time by doing any necessary untagging in software rather than
hardware.  To enable that, keep the CPU port's Remove Tag flag cleared
and set the dsa_switch::untag_bridge_pvid flag.

Fixes: e66f840c ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a VLAN is deleted from a port, the flags in struct
switchdev_obj_port_vlan are always 0.  ksz8_port_vlan_del() copies the
BRIDGE_VLAN_INFO_UNTAGGED flag to the port's Tag Removal flag, and
therefore always clears it.

In case there are multiple VLANs configured as untagged on this port -
which seems useless, but is allowed - deleting one of them changes the
remaining VLANs to be tagged.

It's only ever necessary to change this flag when a VLAN is added to
the port, so leave it unchanged in ksz8_port_vlan_del().

Fixes: e66f840c ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

The switches supported by ksz8795 only have a per-port flag for Tag
Removal.  This means it is not possible to support both tagged and
untagged VLANs on the same port.  Reject attempts to add a VLAN that
requires the flag to be changed, unless there are no VLANs currently
configured.

VID 0 is excluded from this check since it is untagged regardless of
the state of the flag.

On the CPU port we could support tagged and untagged VLANs at the same
time.  This will be enabled by a later patch.

Fixes: e66f840c ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

ksz8795 has never actually enabled PVID tag insertion, and it also
programmed the PVID incorrectly.  To fix this:

* Allow tag insertion to be controlled per ingress port.  On most
  chips, set bit 2 in Global Control 19.  On KSZ88x3 this control
  flag doesn't exist.

* When adding a PVID:
  - Set the appropriate register bits to enable tag insertion on
    egress at every other port if this was the packet's ingress port.
  - Mask *out* the VID from the default tag, before or-ing in the new
    PVID.

* When removing a PVID:
  - Clear the same control bits to disable tag insertion.
  - Don't update the default tag.  This wasn't doing anything useful.

Fixes: e66f840c ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

ksz_read64() currently does some dubious byte-swapping on the two
halves of a 64-bit register, and then only returns the high bits.
Replace this with a straightforward expression.

Fixes: e66f840c ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.14-20210810' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

linux-can-fixes-for-5.14-20210810

Marc Kleine-Budde says:

====================
pull-request: can 2021-08-10

this is a pull request of 2 patches for net/master.

Baruch Siach's patch fixes a typo for the Microchip CAN BUS Analyzer
Tool entry in the MAINTAINERS file.

Hussein Alasadi fixes the setting of the M_CAN_DBTP register in the
m_can driver. The regression git mainline in v5.14-rc1, so no backport
to stable is needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 fixes 2021-08-09

This series introduces fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-08-09

This series contains updates to ice and iavf drivers.

Ani prevents the ice driver from accidentally being probed to a virtual
function and stops processing of VF messages when VFs are being torn
down.

Brett prevents the ice driver from deleting is own MAC address.

Fahad ensures the RSS LUT and key are always set following reset for
iavf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b910eaaa ("bpf: Fix NULL pointer dereference in bpf_get_local_storage()
helper") fixed a bug for bpf_get_local_storage() helper so different tasks
won't mess up with each other's percpu local storage.

The percpu data contains 8 slots so it can hold up to 8 contexts (same or
different tasks), for 8 different program runs, at the same time. This in
general is sufficient. But our internal testing showed the following warning
multiple times:

  [...]
  warning: WARNING: CPU: 13 PID: 41661 at include/linux/bpf-cgroup.h:193
     __cgroup_bpf_run_filter_sock_ops+0x13e/0x180
  RIP: 0010:__cgroup_bpf_run_filter_sock_ops+0x13e/0x180
  <IRQ>
   tcp_call_bpf.constprop.99+0x93/0xc0
   tcp_conn_request+0x41e/0xa50
   ? tcp_rcv_state_process+0x203/0xe00
   tcp_rcv_state_process+0x203/0xe00
   ? sk_filter_trim_cap+0xbc/0x210
   ? tcp_v6_inbound_md5_hash.constprop.41+0x44/0x160
   tcp_v6_do_rcv+0x181/0x3e0
   tcp_v6_rcv+0xc65/0xcb0
   ip6_protocol_deliver_rcu+0xbd/0x450
   ip6_input_finish+0x11/0x20
   ip6_input+0xb5/0xc0
   ip6_sublist_rcv_finish+0x37/0x50
   ip6_sublist_rcv+0x1dc/0x270
   ipv6_list_rcv+0x113/0x140
   __netif_receive_skb_list_core+0x1a0/0x210
   netif_receive_skb_list_internal+0x186/0x2a0
   gro_normal_list.part.170+0x19/0x40
   napi_complete_done+0x65/0x150
   mlx5e_napi_poll+0x1ae/0x680
   __napi_poll+0x25/0x120
   net_rx_action+0x11e/0x280
   __do_softirq+0xbb/0x271
   irq_exit_rcu+0x97/0xa0
   common_interrupt+0x7f/0xa0
   </IRQ>
   asm_common_interrupt+0x1e/0x40
  RIP: 0010:bpf_prog_1835a9241238291a_tw_egress+0x5/0xbac
   ? __cgroup_bpf_run_filter_skb+0x378/0x4e0
   ? do_softirq+0x34/0x70
   ? ip6_finish_output2+0x266/0x590
   ? ip6_finish_output+0x66/0xa0
   ? ip6_output+0x6c/0x130
   ? ip6_xmit+0x279/0x550
   ? ip6_dst_check+0x61/0xd0
  [...]

Using drgn [0] to dump the percpu buffer contents showed that on this CPU
slot 0 is still available, but slots 1-7 are occupied and those tasks in
slots 1-7 mostly don't exist any more. So we might have issues in
bpf_cgroup_storage_unset().

Further debugging confirmed that there is a bug in bpf_cgroup_storage_unset().
Currently, it tries to unset "current" slot with searching from the start.
So the following sequence is possible:

  1. A task is running and claims slot 0
  2. Running BPF program is done, and it checked slot 0 has the "task"
     and ready to reset it to NULL (not yet).
  3. An interrupt happens, another BPF program runs and it claims slot 1
     with the *same* task.
  4. The unset() in interrupt context releases slot 0 since it matches "task".
  5. Interrupt is done, the task in process context reset slot 0.

At the end, slot 1 is not reset and the same process can continue to occupy
slots 2-7 and finally, when the above step 1-5 is repeated again, step 3 BPF
program won't be able to claim an empty slot and a warning will be issued.

To fix the issue, for unset() function, we should traverse from the last slot
to the first. This way, the above issue can be avoided.

The same reverse traversal should also be done in bpf_get_local_storage() helper
itself. Otherwise, incorrect local storage may be returned to BPF program.

  [0] https://github.com/osandov/drgn

Fixes: b910eaaa ("bpf: Fix NULL pointer dereference in bpf_get_local_storage() helper")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210810010413.1976277-1-yhs@fb.com

Commit 79a7f8bd ("bpf: Introduce bpf_sys_bpf() helper and program type.")
added support for syscall program, which is a sleepable program.

But the program run missed bpf_read_lock_trace()/bpf_read_unlock_trace(),
which is needed to ensure proper rcu callback invocations. This patch adds
bpf_read_[un]lock_trace() properly.

Fixes: 79a7f8bd ("bpf: Introduce bpf_sys_bpf() helper and program type.")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210809235151.1663680-1-yhs@fb.com

Back then, commit 96ae5227 ("bpf: Add bpf_probe_write_user BPF helper
to be called in tracers") added the bpf_probe_write_user() helper in order
to allow to override user space memory. Its original goal was to have a
facility to "debug, divert, and manipulate execution of semi-cooperative
processes" under CAP_SYS_ADMIN. Write to kernel was explicitly disallowed
since it would otherwise tamper with its integrity.

One use case was shown in cf9b1199 ("samples/bpf: Add test/example of
using bpf_probe_write_user bpf helper") where the program DNATs traffic
at the time of connect(2) syscall, meaning, it rewrites the arguments to
a syscall while they're still in userspace, and before the syscall has a
chance to copy the argument into kernel space. These days we have better
mechanisms in BPF for achieving the same (e.g. for load-balancers), but
without having to write to userspace memory.

Of course the bpf_probe_write_user() helper can also be used to abuse
many other things for both good or bad purpose. Outside of BPF, there is
a similar mechanism for ptrace(2) such as PTRACE_PEEK{TEXT,DATA} and
PTRACE_POKE{TEXT,DATA}, but would likely require some more effort.
Commit 96ae5227 explicitly dedicated the helper for experimentation
purpose only. Thus, move the helper's availability behind a newly added
LOCKDOWN_BPF_WRITE_USER lockdown knob so that the helper is disabled under
the "integrity" mode. More fine-grained control can be implemented also
from LSM side with this change.

Fixes: 96ae5227 ("bpf: Add bpf_probe_write_user BPF helper to be called in tracers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>

This patch fixes the setting of the M_CAN_DBTP register contents:
- use DBTP_ (the data bitrate macros) instead of NBTP_ which area used
  for the nominal bitrate
- do not overwrite possibly-existing DBTP_TDC flag by ORing reg_btp
  instead of overwriting

Link: https://lore.kernel.org/r/FRYP281MB06140984ABD9994C0AAF7433D1F69@FRYP281MB0614.DEUP281.PROD.OUTLOOK.COM
Fixes: 20779943 ("can: m_can: use bits.h macros for all regmasks")
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Hussein Alasadi <alasadi@arecs.eu>
[mkl: update patch description, update indention]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the abbreviated name of the Microchip CAN BUS
Analyzer Tool.

Fixes: 8a7b46fa ("MAINTAINERS: add Yasushi SHOJI as reviewer for the Microchip CAN BUS Analyzer Tool driver")
Link: https://lore.kernel.org/r/cc4831cb1c8759c15fb32c21fd326e831183733d.1627876781.git.baruch@tkos.co.ilSigned-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Check return value of mlx5_fw_tracer_start(), set error path and fix
return value of mlx5_fw_tracer_init() accordingly.

Fixes: c71ad41c ("net/mlx5: FW tracer, events handling")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The CQ destroy is performed based on the IRQ number that is stored in
cq->irqn. That number wasn't set explicitly during CQ creation and as
expected some of the API users of mlx5_core_create_cq() forgot to update
it.

This caused to wrong synchronization call of the wrong IRQ with a number
0 instead of the real one.

As a fix, set the IRQ number directly in the mlx5_core_create_cq() and
update all users accordingly.

Fixes: 1a86b377 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Fixes: ef1659ad ("IB/mlx5: Add DEVX support for CQ events")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Free the offload sample action on error.

Fixes: f94d6389 ("net/mlx5e: TC, Add support to offload sample action")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Destroy pool->mutex when we destroy the pool.

Fixes: c36326d3 ("net/mlx5: Round-Robin EQs over IRQs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently irq->pool is set after the irq is insert to the xarray.
Set irq->pool before the irq is inserted to the xarray.

Fixes: 71e084e2 ("net/mlx5: Allocating a pool of MSI-X vectors for SFs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Change order of functions in mlx5_irq_detach_nb() so it will be
a mirror of mlx5_irq_attach_nb.

Fixes: 71e084e2 ("net/mlx5: Allocating a pool of MSI-X vectors for SFs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Since switchdev mode can't support  devlink traps, verify there are
no active devlink traps before moving eswitch to switchdev mode. If
there are active traps, prevent the switchdev mode configuration.

Fixes: eb3862a0 ("net/mlx5e: Enable traps according to link state")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

mlx5e_close_xdpsq does the cleanup: it calls mlx5e_free_xdpsq_descs to
free the outstanding descriptors, which relies on
mlx5e_page_release_dynamic and page_pool_release_page. However,
page_pool_destroy is already called by this point, because
mlx5e_close_rq runs before mlx5e_close_xdpsq.

This commit fixes the use-after-free by swapping mlx5e_close_xdpsq and
mlx5e_close_rq.

The commit cited below started calling page_pool_destroy directly from
the driver. Previously, the page pool was destroyed under a call_rcu
from xdp_rxq_info_unreg_mem_model, which would defer the deallocation
until after the XDPSQ is cleaned up.

Fixes: 1da4bbef ("net: core: page_pool: add user refcnt and reintroduce page_pool_destroy")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Ageing time is not converted from clock_t to jiffies which results
incorrect ageing timeout calculation in workqueue update task. Fix it by
applying clock_t_to_jiffies() to provided value.

Fixes: c636a0f0 ("net/mlx5: Bridge, dynamic entry ageing")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

It could be local and remote are on the same machine and the route
result will be a local route which will result in creating encap id
with src/dst mac address of 0.

Fixes: a54e20b4 ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

While processing encapsulated packet on RX, one of the fields that is
checked is the inner packet length. If the length as specified in the header
doesn't match the actual inner packet length, the packet is invalid
and should be dropped. However, such packet caused the NIC to hang.

This patch turns on a 'fail_on_error' HW bit which allows HW to drop
such an invalid packet while processing RX packet and trying to decap it.

Fixes: ad17dc8c ("net/mlx5: DR, Move STEv0 action apply logic")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>