- 30 Jul, 2015 11 commits
-
-
Sunil Goutham authored
Fixing TSO packages not being counted. Signed-off-by:
Sunil Goutham <sgoutham@cavium.com> Signed-off-by:
Aleksey Makarov <aleksey.makarov@caviumnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sunil Goutham authored
Fix for memory leak when changing queue/channel count via ethtool Signed-off-by:
-
Sunil Goutham authored
With earlier configured value sufficient number of CQEs are not being reserved for transmitted packets. Hence under heavy incoming traffic load, receive notifications will take away most of the CQ thus transmit notifications will be lost resulting in tx skbs not being freed. Finally SQ will be full and it will be stopped, watchdog timer will kick in. After this fix receive notifications will not take morethan half of CQ reserving the rest for transmit notifications. Also changed CQ & SQ sizes from 16k to 4k. This is also due to the receive notifications taking first half of CQ under heavy load and time taken by NAPI to clear transmit notifications will increase with higher queue sizes. Again results in SQ being stopped. Signed-off-by:
-
Sunil Goutham authored
Fixed 'tso_hdrs' memory not being freed properly. Also fixed SQ skbuff maintenance issues. Signed-off-by:
-
Sunil Goutham authored
Switching back to LDD transactions from LDWB. While transmitting packets out with LDWB transactions data integrity issues are seen very frequently. hence switching back to LDD. Signed-off-by:
Robert Richter <rrichter@cavium.com> Signed-off-by:
-
Eric Dumazet authored
This patch is the IPv6 equivalent of commit 6c8b4e3f ("arp: flush arp cache on IFF_NOARP change") Without it, we keep buggy neighbours in the cache, with destination MAC address equal to our own MAC address. Tested: tcpdump -i eth0 -s 0 ip6 -n -e & ip link set dev eth0 arp off ping6 remote // sends buggy frames ip link set dev eth0 arp on ping6 remote // should work once kernel is patched Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Mario Fanelli <mariofanelli@google.com> Signed-off-by:
-
David S. Miller authored
Murali Karicheri says: ==================== net: netcp: bug fixes for dynamic module support This series fixes few bugs to allow keystone netcp modules to be dynamically loaded and removed. Currently it allows following sequence multiple times insmod cpsw_ale.ko insmod davinci_mdio.ko insmod keystone_netcp.ko insmod keystone_netcp_ethss.ko ifup eth0 ifup eth1 ping <hosts on eth0> ping <hosts on eth1> ifdown eth1 ifdown eth0 rmmod keystone_netcp_ethss.ko rmmod keystone_netcp.ko rmmod davinci_mdio.ko rmmod cpsw_ale.ko ==================== Signed-off-by: -
Karicheri, Muralidharan authored
This patch clean up error handle code to use goto label properly. In some cases, the code unnecessarily use goto instead of just returning the error code. Code also make explicit calls to devm_* APIs on error which is not necessary. In the gbe_remove() also it makes similar calls which is also unnecessary. Also fix few checkpatch warnings Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Signed-off-by:
-
Karicheri, Muralidharan authored
The code seems to assume a null is returned when the list is empty from first_sec_slave() to break the loop which is incorrect. Fix the code by using list_empty(). Signed-off-by:
-
Karicheri, Muralidharan authored
Currently if user do rmmod keystone_netcp.ko following warning is seen :- [ 59.035891] ------------[ cut here ]------------ [ 59.040535] WARNING: CPU: 2 PID: 1619 at drivers/net/ethernet/ti/ netcp_core.c:2127 netcp_remove) This is because the interface list is not cleaned up in netcp_remove. This patch fixes this. Also fix some checkpatch related warnings. Signed-off-by:
-
Daniel Borkmann authored
With eBPF JIT compiler enabled on x86_64, I was able to reliably trigger the following general protection fault out of an eBPF program with a simple tail call, f.e. tracex5 (or a stripped down version of it): [ 927.097918] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC [...] [ 927.100870] task: ffff8801f228b780 ti: ffff880016a64000 task.ti: ffff880016a64000 [ 927.102096] RIP: 0010:[<ffffffffa002440d>] [<ffffffffa002440d>] 0xffffffffa002440d [ 927.103390] RSP: 0018:ffff880016a67a68 EFLAGS: 00010006 [ 927.104683] RAX: 5a5a5a5a5a5a5a5a RBX: 0000000000000000 RCX: 0000000000000001 [ 927.105921] RDX: 0000000000000000 RSI: ffff88014e438000 RDI: ffff880016a67e00 [ 927.107137] RBP: ffff880016a67c90 R08: 0000000000000000 R09: 0000000000000001 [ 927.108351] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880016a67e00 [ 927.109567] R13: 0000000000000000 R14: ffff88026500e460 R15: ffff880220a81520 [ 927.110787] FS: 00007fe7d5c1f740(0000) GS:ffff880265000000(0000) knlGS:0000000000000000 [ 927.112021] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 927.113255] CR2: 0000003e7bbb91a0 CR3: 000000006e04b000 CR4: 00000000001407e0 [ 927.114500] Stack: [ 927.115737] ffffc90008cdb000 ffff880016a67e00 ffff88026500e460 ffff880220a81520 [ 927.117005] 0000000100000000 000000000000001b ffff880016a67aa8 ffffffff8106c548 [ 927.118276] 00007ffcdaf22e58 0000000000000000 0000000000000000 ffff880016a67ff0 [ 927.119543] Call Trace: [ 927.120797] [<ffffffff8106c548>] ? lookup_address+0x28/0x30 [ 927.122058] [<ffffffff8113d176>] ? __module_text_address+0x16/0x70 [ 927.123314] [<ffffffff8117bf0e>] ? is_ftrace_trampoline+0x3e/0x70 [ 927.124562] [<ffffffff810c1a0f>] ? __kernel_text_address+0x5f/0x80 [ 927.125806] [<ffffffff8102086f>] ? print_context_stack+0x7f/0xf0 [ 927.127033] [<ffffffff810f7852>] ? __lock_acquire+0x572/0x2050 [ 927.128254] [<ffffffff810f7852>] ? __lock_acquire+0x572/0x2050 [ 927.129461] [<ffffffff8119edfa>] ? trace_call_bpf+0x3a/0x140 [ 927.130654] [<ffffffff8119ee4a>] trace_call_bpf+0x8a/0x140 [ 927.131837] [<ffffffff8119edfa>] ? trace_call_bpf+0x3a/0x140 [ 927.133015] [<ffffffff8119f008>] kprobe_perf_func+0x28/0x220 [ 927.134195] [<ffffffff811a1668>] kprobe_dispatcher+0x38/0x60 [ 927.135367] [<ffffffff81174b91>] ? seccomp_phase1+0x1/0x230 [ 927.136523] [<ffffffff81061400>] kprobe_ftrace_handler+0xf0/0x150 [ 927.137666] [<ffffffff81174b95>] ? seccomp_phase1+0x5/0x230 [ 927.138802] [<ffffffff8117950c>] ftrace_ops_recurs_func+0x5c/0xb0 [ 927.139934] [<ffffffffa022b0d5>] 0xffffffffa022b0d5 [ 927.141066] [<ffffffff81174b91>] ? seccomp_phase1+0x1/0x230 [ 927.142199] [<ffffffff81174b95>] seccomp_phase1+0x5/0x230 [ 927.143323] [<ffffffff8102c0a4>] syscall_trace_enter_phase1+0xc4/0x150 [ 927.144450] [<ffffffff81174b95>] ? seccomp_phase1+0x5/0x230 [ 927.145572] [<ffffffff8102c0a4>] ? syscall_trace_enter_phase1+0xc4/0x150 [ 927.146666] [<ffffffff817f9a9f>] tracesys+0xd/0x44 [ 927.147723] Code: 48 8b 46 10 48 39 d0 76 2c 8b 85 fc fd ff ff 83 f8 20 77 21 83 c0 01 89 85 fc fd ff ff 48 8d 44 d6 80 48 8b 00 48 83 f8 00 74 0a <48> 8b 40 20 48 83 c0 33 ff e0 48 89 d8 48 8b 9d d8 fd ff ff 4c [ 927.150046] RIP [<ffffffffa002440d>] 0xffffffffa002440d The code section with the instructions that traps points into the eBPF JIT image of the root program (the one invoking the tail call instruction). Using bpf_jit_disasm -o on the eBPF root program image: [...] 4e: mov -0x204(%rbp),%eax 8b 85 fc fd ff ff 54: cmp $0x20,%eax <--- if (tail_call_cnt > MAX_TAIL_CALL_CNT) 83 f8 20 57: ja 0x000000000000007a 77 21 59: add $0x1,%eax <--- tail_call_cnt++ 83 c0 01 5c: mov %eax,-0x204(%rbp) 89 85 fc fd ff ff 62: lea -0x80(%rsi,%rdx,8),%rax <--- prog = array->prog[index] 48 8d 44 d6 80 67: mov (%rax),%rax 48 8b 00 6a: cmp $0x0,%rax <--- check for NULL 48 83 f8 00 6e: je 0x000000000000007a 74 0a 70: mov 0x20(%rax),%rax <--- GPF triggered here! fetch of bpf_func 48 8b 40 20 [ matches <48> 8b 40 20 ... from above ] 74: add $0x33,%rax <--- prologue skip of new prog 48 83 c0 33 78: jmpq *%rax <--- jump to new prog insns ff e0 [...] The problem is that rax has 5a5a5a5a5a5a5a5a, which suggests a tail call jump to map slot 0 is pointing to a poisoned page. The issue is the following: lea instruction has a wrong offset, i.e. it should be ... lea 0x80(%rsi,%rdx,8),%rax ... but it actually seems to be ... lea -0x80(%rsi,%rdx,8),%rax ... where 0x80 is offsetof(struct bpf_array, prog), thus the offset needs to be positive instead of negative. Disassembling the interpreter, we btw similarly do: [...] c88: lea 0x80(%rax,%rdx,8),%rax <--- prog = array->prog[index] 48 8d 84 d0 80 00 00 00 c90: add $0x1,%r13d 41 83 c5 01 c94: mov (%rax),%rax 48 8b 00 [...] Now the other interesting fact is that this panic triggers only when things like CONFIG_LOCKDEP are being used. In that case offsetof(struct bpf_array, prog) starts at offset 0x80 and in non-CONFIG_LOCKDEP case at offset 0x50. Reason is that the work_struct inside struct bpf_map grows by 48 bytes in my case due to the lockdep_map member (which also has CONFIG_LOCK_STAT enabled members). Changing the emitter to always use the 4 byte displacement in the lea instruction fixes the panic on my side. It increases the tail call instruction emission by 3 more byte, but it should cover us from various combinations (and perhaps other future increases on related structures). After patch, disassembly: [...] 9e: lea 0x80(%rsi,%rdx,8),%rax <--- CONFIG_LOCKDEP/CONFIG_LOCK_STAT 48 8d 84 d6 80 00 00 00 a6: mov (%rax),%rax 48 8b 00 [...] [...] 9e: lea 0x50(%rsi,%rdx,8),%rax <--- No CONFIG_LOCKDEP 48 8d 84 d6 50 00 00 00 a6: mov (%rax),%rax 48 8b 00 [...] Fixes: b52f00e6 ("x86: bpf_jit: implement bpf_tail_call() helper") Signed-off-by:Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
-
- 29 Jul, 2015 7 commits
-
-
Nikolay Aleksandrov authored
Since mdb states were introduced when deleting an entry the state was left as it was set in the delete request from the user which leads to the following output when doing a monitor (for example): $ bridge mdb add dev br0 port eth3 grp 239.0.0.1 permanent (monitor) dev br0 port eth3 grp 239.0.0.1 permanent $ bridge mdb del dev br0 port eth3 grp 239.0.0.1 permanent (monitor) dev br0 port eth3 grp 239.0.0.1 temp ^^^ Note the "temp" state in the delete notification which is wrong since the entry was permanent, the state in a delete is always reported as "temp" regardless of the real state of the entry. After this patch: $ bridge mdb add dev br0 port eth3 grp 239.0.0.1 permanent (monitor) dev br0 port eth3 grp 239.0.0.1 permanent $ bridge mdb del dev br0 port eth3 grp 239.0.0.1 permanent (monitor) dev br0 port eth3 grp 239.0.0.1 permanent There's one important note to make here that the state is actually not matched when doing a delete, so one can delete a permanent entry by stating "temp" in the end of the command, I've chosen this fix in order not to break user-space tools which rely on this (incorrect) behaviour. So to give an example after this patch and using the wrong state: $ bridge mdb add dev br0 port eth3 grp 239.0.0.1 permanent (monitor) dev br0 port eth3 grp 239.0.0.1 permanent $ bridge mdb del dev br0 port eth3 grp 239.0.0.1 temp (monitor) dev br0 port eth3 grp 239.0.0.1 permanent Note the state of the entry that got deleted is correct in the notification. Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: ccb1c31a ("bridge: add flags to distinguish permanent mdb entires") Signed-off-by:
-
Satish Ashok authored
When fast leave is configured on a bridge port and an IGMP leave is received for a group, the group is not deleted immediately if there is a router detected or if multicast querier is configured. Ideally the group should be deleted immediately when fast leave is configured. Signed-off-by:
Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by:
-
Toshiaki Makita authored
There are several devices that can receive vlan tagged packets with CHECKSUM_PARTIAL like tap, possibly veth and xennet. When (multiple) vlan tagged packets with CHECKSUM_PARTIAL are forwarded by bridge to a device with the IP_CSUM feature, they end up with checksum error because before entering bridge, the network header is set to ETH_HLEN (not including vlan header length) in __netif_receive_skb_core(), get_rps_cpu(), or drivers' rx functions, and nobody fixes the pointer later. Since the network header is exepected to be ETH_HLEN in flow-dissection and hash-calculation in RPS in rx path, and since the header pointer fix is needed only in tx path, set the appropriate network header on forwarding packets. Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by:
-
Alexander Drozdov authored
tpacket_fill_skb() can return a negative value (-errno) which is stored in tp_len variable. In that case the following condition will be (but shouldn't be) true: tp_len > dev->mtu + dev->hard_header_len as dev->mtu and dev->hard_header_len are both unsigned. That may lead to just returning an incorrect EMSGSIZE errno to the user. Fixes: 52f1454f ("packet: allow to transmit +4 byte in TX_RING slot for VLAN case") Signed-off-by:
Alexander Drozdov <al.drozdov@gmail.com> Acked-by:
-
Eric Dumazet authored
When arp is off on a device, and ioctl(SIOCGARP) is queried, a buggy answer is given with MAC address of the device, instead of the mac address of the destination/gateway. We filter out NUD_NOARP neighbours for /proc/net/arp, we must do the same for SIOCGARP ioctl. Tested: lpaa23:~# ./arp 10.246.7.190 MAC=00:01:e8:22:cb:1d // correct answer lpaa23:~# ip link set dev eth0 arp off lpaa23:~# cat /proc/net/arp # check arp table is now 'empty' IP address HW type Flags HW address Mask Device lpaa23:~# ./arp 10.246.7.190 MAC=00:1a:11:c3:0d:7f // buggy answer before patch (this is eth0 mac) After patch : lpaa23:~# ip link set dev eth0 arp off lpaa23:~# ./arp 10.246.7.190 ioctl(SIOCGARP) failed: No such device or address Signed-off-by:
Vytautas Valancius <valas@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
-
David Ward authored
This notification causes the FIB to be updated, which is not needed because the address already exists, and more importantly it may undo intentional changes that were made to the FIB after the address was originally added. (As a point of comparison, when an address becomes deprecated because its preferred lifetime expired, a notification on this chain is not generated.) The motivation for this commit is fixing an incompatibility between DHCP clients which set and update the address lifetime according to the lease, and a commercial VPN client which replaces kernel routes in a way that outbound traffic is sent only through the tunnel (and disconnects if any further route changes are detected via netlink). Signed-off-by:
David Ward <david.ward@ll.mit.edu> Signed-off-by:
-
Nikolay Aleksandrov authored
These should be handled only by the respective STP which is in control. They become problematic for devices with limited resources with many ports because the hold_timer is per port and fires each second and the hello timer fires each 2 seconds even though it's global. While in user-space STP mode these timers are completely unnecessary so it's better to keep them off. Also ensure that when the bridge is up these timers are started only when running with kernel STP. Signed-off-by:
-
- 27 Jul, 2015 22 commits
-
-
Lars Westerhoff authored
When binding a PF_PACKET socket, the use count of the bound interface is always increased with dev_hold in dev_get_by_{index,name}. However, when rebound with the same protocol and device as in the previous bind the use count of the interface was not decreased. Ultimately, this caused the deletion of the interface to fail with the following message: unregister_netdevice: waiting for dummy0 to become free. Usage count = 1 This patch moves the dev_put out of the conditional part that was only executed when either the protocol or device changed on a bind. Fixes: 902fefb8 ('packet: improve socket create/bind latency in some cases') Signed-off-by:Lars Westerhoff <lars.westerhoff@newtec.eu> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
-
Ivan Vecera authored
Network header is set with offset ETH_HLEN but it is not true for VLAN (multiple-)tagged and results in checksum issues in lower devices. v2: leave skb->protocol untouched (thx Vlad), comment added v3: moved after skb_probe_transport_header() call (thx Toshiaki) Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
-
Alexander Duyck authored
It was reported that update_suffix was taking a long time on systems where a large number of leaves were attached to a single node. As it turns out fib_table_flush was calling update_suffix for each leaf that didn't have all of the aliases stripped from it. As a result, on this large node removing one leaf would result in us calling update_suffix for every other leaf on the node. The fix is to just remove the calls to leaf_pull_suffix since they are redundant as we already have a call in resize that will go through and update the suffix length for the node before we exit out of fib_table_flush or fib_table_flush_external. Reported-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
Alexander Duyck <alexander.h.duyck@redhat.com> Tested-by:
-
David S. Miller authored
If an architecture defines readl/writel using CPP macros, we get the following kinds of build failure: > > > drivers/net/ethernet/cadence/macb.c:164:1: error: macro "writel" > > > passed 3 arguments, but takes just 2 > macb_or_gem_writel(bp, SA1B, bottom); > ^ Rename the methods so that this doesn't happen. Signed-off-by: -
Andrew Lunn authored
When a switch is attached to the mdio bus, the mdio bus can be used while the interface is not open. If the IPG clock is not enabled, MDIO reads/writes will simply time out. Add support for runtime PM to control this clock. Enable/disable this clock using runtime PM, with open()/close() and mdio read()/write() function triggering runtime PM operations. Since PM is optional, the IPG clock is enabled at probe and is no longer modified by fec_enet_clk_enable(), thus if PM is not enabled in the kernel, it is guaranteed the clock is running when MDIO operations are performed. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Cc: tyler.baker@linaro.org Cc: fabio.estevam@freescale.com Cc: shawn.guo@linaro.org Tested-by:
Fabio Estevam <fabio.estevam@freescale.com> Tested-by:
Tyler Baker <tyler.baker@linaro.org> Signed-off-by:
-
WingMan Kwok authored
This patch asserts SGMII RTRESET, i.e. resetting the SGMII Tx/Rx logic, during network interface shutdown to avoid having the hardware wedge when shutting down with high incoming traffic rates. This is cleared (brought out of RTRESET) when the interface is brought back up. Signed-off-by:
WingMan Kwok <w-kwok2@ti.com> Signed-off-by:
-
David S. Miller authored
Andy Shevchenko says: ==================== net/macb: fix for AVR32 and clean up It seems no one had tested recently the driver on AVR32 platforms such as ATNGW100. This series bring it back to work. ==================== Signed-off-by: -
Andy Shevchenko authored
This patch coverts struct description to the kernel doc format. There is no functional change. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Andy Shevchenko authored
macb_count_tx_descriptors() repeats the generic macro DIV_ROUND_UP(). The patch does a replacement. There is no functional change. Signed-off-by:
-
Andy Shevchenko authored
This patch fixes the following warnings: drivers/net/ethernet/cadence/macb.c: In function ‘macb_handle_link_change’: drivers/net/ethernet/cadence/macb.c:266: warning: comparison between signed and unsigned drivers/net/ethernet/cadence/macb.c:267: warning: comparison between signed and unsigned drivers/net/ethernet/cadence/macb.c:291: warning: comparison between signed and unsigned drivers/net/ethernet/cadence/macb.c: In function ‘gem_update_stats’: drivers/net/ethernet/cadence/macb.c:1908: warning: comparison between signed and unsigned drivers/net/ethernet/cadence/macb.c: In function ‘gem_get_ethtool_strings’: drivers/net/ethernet/cadence/macb.c:1988: warning: comparison between signed and unsigned Signed-off-by:
-
Andy Shevchenko authored
To avoid messages like macb macb.0 (unnamed net_device) (uninitialized): Cadence caps 0x00000000 macb macb.0 (unnamed net_device) (uninitialized): invalid hw address, using random let's use dev_*() macros. Signed-off-by:
-
Andy Shevchenko authored
The commit 98b5a0f4 introduces jumbo frame support, but also it assumes that macb_config present which is not always true. The configuration without macb_config fails to boot. Unable to handle kernel NULL pointer dereference at virtual address 00000010 ptbr = 90350000 pgd = 00000000 Oops: Kernel access of bad area, sig: 11 [#1] FRAME_POINTER chip: 0x01f:0x1e82 rev 2 Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 4.2.0-rc3-next-20150723+ #13 task: 91c26000 ti: 91c28000 task.ti: 91c28000 PC is at macb_probe+0x140/0x61c Fixes: 98b5a0f4 (net: macb: Add support for jumbo frames) Signed-off-by:
-
Andy Shevchenko authored
The commit a50dad35 (net: macb: Add big endian CPU support) converted I/O accessors to readl_relaxed() and writel_relaxed() and consequentially broke MACB driver on AVR32 platforms such as ATNGW100. This patch improves I/O access by checking endiannes first and use the corresponding methods. Fixes: a50dad35 (net: macb: Add big endian CPU support) Signed-off-by:
-
Sabrina Dubroca authored
Currently, tcp_recvmsg enters a busy loop in sk_wait_data if called with flags = MSG_WAITALL | MSG_PEEK. sk_wait_data waits for sk_receive_queue not empty, but in this case, the receive queue is not empty, but does not contain any skb that we can use. Add a "last skb seen on receive queue" argument to sk_wait_data, so that it sleeps until the receive queue has new skbs. Link: https://bugzilla.kernel.org/show_bug.cgi?id=99461 Link: https://sourceware.org/bugzilla/show_bug.cgi?id=18493 Link: https://bugzilla.redhat.com/show_bug.cgi?id=1205258Reported-by:
Enrico Scholz <rh-bugzilla@ensc.de> Reported-by:
Dan Searle <dan@censornet.com> Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Acked-by:
-
David S. Miller authored
Hayes Wang says: ==================== r8152: issues fix v2: Replace patch #2 with "r8152: fix wakeup settings". v1: These patches are used to fix issues. ==================== Signed-off-by: -
hayeswang authored
Adjust napi_disable() and napi_enable() to avoid r8152_poll() start working before rx ready. Otherwise, it may have race condition for rx_agg. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
hayeswang authored
Avoid the driver to enable WOL if the device doesn't support it. Signed-off-by:
-
hayeswang authored
- Disable U1/U2 during initialization. - Disable lpm when linking is on, and enable it when linking is off. - Disable U1/U2 when enabling runtime suspend. It is possible to let hw stop working, if the U1/U2 request occurs during some situations. The patch is used to avoid it. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetoothDavid S. Miller authored
Johan Hedberg says: ==================== pull request: bluetooth 2015-07-23 Here's another one-patch pull request for 4.2 which targets a potential NULL pointer dereference in the LE Security Manager code that can be triggered by using older user space tools. The issue has been there since 4.0 so there's the appropriate "Cc: stable" in place. Let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: -
Lucas Stach authored
This function frees resources and cancels delayed work item that have been initialized in fec_ptp_init(). Use this to do proper error handling if something goes wrong in probe function after fec_ptp_init has been called. Signed-off-by:
Fugang Duan <B38611@freescale.com> Signed-off-by:
-
Lucas Stach authored
So it gets freed when the device is going away. This fixes a DMA memory leak on driver probe() fail and driver remove(). Signed-off-by:
-
Jiri Pirko authored
Fixes: a3138df9 ("[NIU]: Add Sun Neptune ethernet driver.") Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
