Replace long udelays with mdelays.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Just use likely/unlikely.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use generic Linux error codes to replace cvmx_usb_status_t.

The conversion table:

	Before				After
	cvmx_usb_status_t		int
	CVMX_USB_SUCCESS		0
	CVMX_USB_INVALID_PARAM		-EINVAL
	CVMX_USB_NO_MEMORY		-ENOMEM
	CVMX_USB_BUSY			-EBUSY
	CVMX_USB_TIMEOUT		-ETIMEDOUT
	CVMX_USB_INCORRECT_MODE		Deleted (was never used)
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Delete __cplusplus.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Delete redundant example code found in comments. It's already there in
the driver proper.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Delete redudant debug flags and dead code behind them.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Delete call, parameter, and return value tracing.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use CVMX_BOARD_TYPE_UBNT_E100 for EdgeRouter Lite.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB driver should depend on SOC instead of CPU.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed a pointer asterisk placement issue
Signed-off-by: Lilis Iskandar <veeableful@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed code indent issues
Signed-off-by: Lilis Iskandar <veeableful@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed C99 comments
Signed-off-by: Lilis Iskandar <veeableful@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed brace issues
Signed-off-by: Lilis Iskandar <veeableful@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This one fixes spacing/tabbing issues.
Signed-off-by: Lilis Iskandar <veeableful@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On resume the slave controller is reinitialized. The tegra i2c master
controller disables the clock at the end of the initialiation, propably
to save some power, and enables it again on each transfer. We don't
do this yet and also forgot to enable the clock on resume. Fix this
copy-paste error by not disabling the clock after initialization.

This didn't striked us yet because suspend/resume hasn't landed in mainline
yet, but will soon.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Conflict resolution for function name set_endian when building for powerpc
The name changed to gdm_set_endian
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Won Kang <wonkang@gctsemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a lot of sparse warnings about use of obsolete
struct and array initializer.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a lot of non-ANSI sparse warnings by adding void to
parameterless functions.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want these fixes here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control fixes from Linus Walleij:
 - Driver fixes for AM33xx, SIRF and PFC pin controllers
 - Fix a compile warning from the pinctrl single-register driver
 - Fix a little nasty memory leak

* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: fix a memleak when freeing maps
  pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
  pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
  arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
  pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
  pinctrl: sirf: fix the pin number and mux bit for usp0
  pinctrl: am33xx dt binding: correct include path

Merge tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "Oleg is working on fixing a very tight race between opening a event
  file and deleting that event at the same time (both must be done as
  root).

  I also found a bug while testing Oleg's patches which has to do with a
  race with kprobes using the function tracer.

  There's also a deadlock fix that was introduced with the previous
  fixes"

* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
  ftrace: Add check for NULL regs if ops has SAVE_REGS set
  tracing: Kill trace_cpu struct/members
  tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
  tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
  tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
  tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
  tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
  tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()

Pull SCSI fixes from James Bottomley:
 "This is five bug fixes, two of which fix long standing problems
  causing crashes (sd and mvsas).  The remaining three are hung (isci
  race) or lost (qla2xxx, isci) devices"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] isci: fix breakage caused by >16byte CDB patch
  [SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
  [SCSI] sd: fix crash when UA received on DIF enabled device
  [SCSI] qla2xxx: Properly set the tagging for commands.
  [SCSI] isci: Fix a race condition in the SSP task management path

Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Forest Bond <forest@alittletooquiet.net>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Devendra Naga <devendra.aaru@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In function zram_bvec_write(), previous data at the index is
already freed by function zram_free_page().
When failed to compress or zs_malloc, there is no way to restore old data.
Therefore, free previous data when it's about to update.

Also, no need to check whether table is not empty outside of
function zram_free_page(), because the function properly checks inside.
Signed-off-by: Sunghan Suh <sunghan.suh@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No one has the hardware for it anymore, and there has not been any
development on it in a long time.

If someone shows up with the hardware, and wants to clean it up, this
can be easily reverted.
Reported-by: Lidza Louina <lidza.louina@gmail.com>
Cc: Jakub Schmidtke <sjakub@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These functions are identical other than the which and how many urbs
are unlinked.

Consolidate the functions into one usbdux_unlink_urbs() function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetic reasons, move the defines used for the bulk transfer
commands out of the middle of the code and rename them so they are
a bit more readable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This define is not used, and it's actually incorrect. The usbdux device
only has 4 analog output channels.

Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'dac_commands' buffer is used to pass the ao channel list from
usbdux_ao_cmd() to the urb callback, usbduxsub_ao_isoc_irq(). This
buffer does not need to be allocated.

Change it into a simple array of the correct size. Rename the variable
to 'ao_chanlist' to clarify what it actually is.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This check is not necessary. The cmd->chanlist_len will always be
less than or equal to the subdevice len_chanlist that was setup
during the attach of the device.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This check is not necessary. The cmd->chanlist_len will always be
less than or equal to the subdevice len_chanlist that was setup
during the attach of the device.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the ugly casting of datap to the ao urb->transfer_buffer. The format
of the data in the buffer is simply.

  [0] = # of channels to update (s->async->cmd.chanlist.len)
  [1] = lsb of value for 1st channel to update
  [2] = msb of value for 1st channel to update
  [3] = 1st channel to update (depvriv->dac_commands[0])

If more than 1 channel is to be updated they are simply added to the buffer:

  [4] = lsb of value for 2st channel to update
  [5] = msb of value for 2st channel to update
  [6] = 1st channel to update (depvriv->dac_commands[1])

etc.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This buffer is used to cache the values that are written to the
analog output channels. Currently it only caches the single writes
to the channels using the (*insn_write) callback. The async command
writes are not cached. The buffer is also being kzalloc'ed during
the attach of the driver to a size much larger that required.

Rename the CamelCase buffer and change it to an array in the private
data of the correct size to cache the analog output channel values.

Modify the analog output urb callback so it updates the cached values
with those used for the asynchronous command to allow readback after
the command completes.

The sanity check of the index to dac_commands[] (i.e. the 'chan' being
written) is not needed. The chanlist_len will always be less than the
number of channels.

Also, fix the dev_err() message so it uses the proper device pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The usbdux and usbduxsigma drivers are _very_ similar. For aesthetic
reasons, rename the private data variables in this driver to match
the names in the usbduxsigma driver so we can start sharing the
common code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the comedi_range_is_bipolar() helper instead of checking the
'range' index against a magic number.

Also, use the s->maxdata to calculate the value needed to munge the
value for bipolar data instead of the magic number.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetics, move this function closer to the (*auto_attach).

Also, rename some of the defined constants that are used by the
firmware upload.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>