[ Upstream commit d5c7b4d5 ]

Commit a22950c8 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 86aacdca ]

"rem * SDM_DEN" can easily overflow on the 32-bit Meson8 and Meson8b
SoCs if the "remainder" (after the division operation) is greater than
262143Hz. This is likely to happen since the input clock for the MPLLs
on Meson8 and Meson8b is "fixed_pll", which is running at a rate of
2550MHz.

One example where this was observed to be problematic was the Ethernet
clock calculation (which takes MPLL2 as input). When requesting a rate
of 125MHz there is a remainder of 2500000Hz.
The resulting MPLL2 rate before this patch was 127488329Hz.
The resulting MPLL2 rate after this patch is 124999103Hz.

Commit b609338b ("clk: meson: mpll: use 64bit math in
rate_from_params") already fixed a similar issue in rate_from_params.

Fixes: 007e6e5c ("clk: meson: mpll: add rw operation")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ce9ce741 ]

Casting to u16 before validating IRD/ORD connection
parameters could cause recording wrong IRD/ORD values
in the cm_node. Validate the IRD/ORD parameters as
they are passed by the application before recording
them.

Fixes: f27b4746 ("i40iw: add connection management code")
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit fe99afd1 ]

Lower Inbound RDMA Read Queue (Q1) object count by a factor of 2
as it is incorrectly doubled. Also, round up Q1 and Transmit FIFO (XF)
object count to power of 2 to satisfy hardware requirement.

Fixes: 86dbcd0f ("i40iw: add file to handle cqp calls")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit df8b13a1 ]

Partial FPDU processing is broken as the sequence number
for the first partial FPDU is wrong due to incorrect
Q2 buffer offset. The offset should be 64 rather than 16.

Fixes: 786c6adb ("i40iw: add puda code")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit e6cfc525 which is
commit 53c81e95 upstream.

Ben writes that there are a number of follow-on patches needed to fix
this up, but they get complex to backport, and some custom fixes are
needed, so let's just revert this and wait for a "real" set of patches
to resolve this to be submitted if it is really needed.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Petr Vorel <pvorel@suse.cz>
Cc: Alexey Kodanev <alexey.kodanev@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 0049457b which was
commit a8b149d3 upstream.

The backport was not correct, so just drop it entirely.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 2f1f60c4 which was
commit 7be4b5dc upstream.

It requires a driver that was not merged until 4.16, so remove it from
this stable tree as it is pointless.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 0ed43f94 which was
comit e153db03 upstream.

It requires a driver that was not merged until 4.16, so remove it from
this stable tree as it is pointless.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bd5c4fac upstream.

I'm getting a slab named "biovec-(1<<(21-12))". It is caused by unintended
expansion of the macro BIO_MAX_PAGES. This patch renames it to biovec-max.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org	# v4.14+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d61d263c upstream.

The driver implementation returns support for private flags, while
no private flags are present. When asked for the number of private
flags it returns the number of statistic flag names.

Fix this by returning EOPNOTSUPP for not implemented ethtool flags.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit aac4619d upstream.

Set powerhold property for tps65917
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 65d9982d upstream.

ECMA-48 [1] (aka ISO 6429) has defined SGR 21 as "doubly underlined"
since at least March 1984.  The Linux kernel has treated it as SGR 22
"normal intensity" since it was added in Linux-0.96b in June 1992.
Before that, it was simply ignored.  Other terminal emulators have
either ignored it, or treat it as double underline now.  xterm for
example added support in its 304 release (May 2014) [2] where it was
previously ignoring it.

Changing this behavior shouldn't be an issue:
- It isn't a named capability in ncurses's terminfo database, so no
  script is using libtinfo/libcurses to look this up, or using tput
  to query & output the right sequence.
- Any script assuming SGR 21 will reset intensity in all terminals
  already do not work correctly on non-Linux VTs (including running
  under screen/tmux/etc...).
- If someone has written a script that only runs in the Linux VT, and
  they're using SGR 21 (instead of SGR 22), the output should still
  be readable.

imo it's important to change this as the Linux VT's non-conformance
is sometimes used as an argument for other terminal emulators to not
implement SGR 21 at all, or do so incorrectly.

[1]: https://www.ecma-international.org/publications/standards/Ecma-048.htm
[2]: https://github.com/ThomasDickey/xterm-snapshots/commit/2fd29cb98d214cb536bcafbee00bc73b3f1eeb9dSigned-off-by: Mike Frysinger <vapier@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 04bb1719 upstream.

The touch sensor buttons on Sony VAIO VGN-CS series laptops (e.g.
VGN-CS31S) are a separate PS/2 device. As the MUX is disabled for all
VAIO machines by the nomux blacklist, the data from touch sensor
buttons and touchpad are combined. The protocol used by the buttons is
probably similar to the touchpad protocol (both are Synaptics) so both
devices get enabled. The controller combines the data, creating a mess
which results in random button clicks, touchpad stopping working and
lost sync error messages:
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 4
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: issuing reconnect request

Add a new i8042_dmi_forcemux_table whitelist with VGN-CS.
With MUX enabled, touch sensor buttons are detected as separate device
(and left disabled as there's currently no driver), fixing all touchpad
problems.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b56af54a upstream.

Reset i8042 before probing because of insufficient BIOS initialisation of
the i8042 serial controller. This makes Synaptics touchpad detection
possible. Without resetting the Synaptics touchpad is not detected because
there are always NACK messages from AUX port.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 567b9b54 upstream.

The primary interface for the touchpad device in Thinkpad L570 is SMBus,
so ALPS overlooked PS2 interface Firmware setting of TrackStick, and
shipped with TrackStick otp bit is disabled.

The address 0xD7 contains device number information, so we can identify
the device by checking this value, but to access it we need to enable
Command mode, and then re-enable the device. Devices shipped in Thinkpad
L570 report either 0x0C or 0x1D as device numbers, if we see them we assume
that the devices are DualPoints.

The same issue exists on Dell Latitude 7370.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196929
Fixes: 646580f793 ("Input: ALPS - fix multi-touch decoding on SS4 plus touchpads")
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Tested-by: Jaak Ristioja <jaak@ristioja.ee>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9de9a449 upstream.

This reverts commit 452562ab ("base: arch_topology: fix section
mismatch build warnings"). It causes the notifier call hangs in some
use-cases.

In some cases with using maxcpus, some of cpus are booted first and
then the remaining cpus are booted. As an example, some users who want
to realize fast boot up often use the following procedure.

  1) Define all CPUs on device tree (CA57x4 + CA53x4)
  2) Add "maxcpus=4" in bootargs
  3) Kernel boot up with CA57x4
  4) After kernel boot up, CA53x4 is booted from user

When kernel init was finished, CPUFREQ_POLICY_NOTIFIER was not still
unregisterd. This means that "__init init_cpu_capacity_callback()"
will be called after kernel init sequence. To avoid this problem,
it needs to remove __init{,data} annotations by reverting this commit.

Also, this commit was needed to fix kernel compile issue below.
However, this issue was also fixed by another patch: commit 82d8ba71
("arch_topology: Fix section miss match warning due to
free_raw_capacity()") in v4.15 as well.
Whereas commit 452562ab added all the missing __init annotations,
commit 82d8ba71 removed it from free_raw_capacity().

WARNING: vmlinux.o(.text+0x548f24): Section mismatch in reference
from the function init_cpu_capacity_callback() to the variable
.init.text:$x
The function init_cpu_capacity_callback() references
the variable __init $x.
This is often because init_cpu_capacity_callback lacks a __init
annotation or the annotation of $x is wrong.

Fixes: 82d8ba71 ("arch_topology: Fix section miss match warning due to free_raw_capacity()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Gaku Inami <gaku.inami.xh@renesas.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e1d9fc04 upstream.

Ack ai fifo error interrupts in interrupt handler to clear interrupt
after fifo overflow.  It should prevent lock-ups after the ai fifo
overflows.

Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 58113753 upstream.

Fstests generic/475 provides a way to fail metadata reads while
checking if checksum exists for the inode inside run_delalloc_nocow(),
and csum_exist_in_range() interprets error (-EIO) as inode having
checksum and makes its caller enter the cow path.

In case of free space inode, this ends up with a warning in
cow_file_range().

The same problem applies to btrfs_cross_ref_exist() since it may also
read metadata in between.

With this, run_delalloc_nocow() bails out when errors occur at the two
places.

cc: <stable@vger.kernel.org> v2.6.28+
Fixes: 17d217fe ("Btrfs: fix nodatasum handling in balancing code")
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8f461b1e upstream.

With ecb-cast5-avx, if a 128+ byte scatterlist element followed a
shorter one, then the algorithm accidentally encrypted/decrypted only 8
bytes instead of the expected 128 bytes.  Fix it by setting the
encryption/decryption 'fn' correctly.

Fixes: c12ab20b ("crypto: cast5/avx - avoid using temporary stack buffers")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6aaf49b4 upstream.

The decision to rebuild .S_shipped is made based on the relative
timestamps of .S_shipped and .pl files but git makes this essentially
random. This means that the perl script might run anyway (usually at
most once per checkout), defeating the whole purpose of _shipped.

Fix by skipping the rule unless explicit make variables are provided:
REGENERATE_ARM_CRYPTO or REGENERATE_ARM64_CRYPTO.

This can produce nasty occasional build failures downstream, for example
for toolchains with broken perl. The solution is minimally intrusive to
make it easier to push into stable.

Another report on a similar issue here: https://lkml.org/lkml/2018/3/8/1379Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0a9eb80e upstream.

rsa-pkcs1pad uses a value returned from a RSA implementation max_size
callback as a size of an input buffer passed to the RSA implementation for
encrypt and sign operations.

CCP RSA implementation uses a hardware input buffer which size depends only
on the current RSA key length, so it should return this key length in
the max_size callback, too.
This also matches what the kernel software RSA implementation does.

Previously, the value returned from this callback was always the maximum
RSA key size the CCP hardware supports.
This resulted in this huge buffer being passed by rsa-pkcs1pad to CCP even
for smaller key sizes and then in a buffer overflow when ccp_run_rsa_cmd()
tried to copy this large input buffer into a RSA key length-sized hardware
input buffer.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Fixes: ceeec0af ("crypto: ccp - Add support for RSA on the CCP")
Cc: stable@vger.kernel.org
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b85149f6 upstream.

caam_remove already removes the debugfs entry, so we need to remove the one
immediately before calling caam_remove.

This fix a NULL dereference at error paths is caam_probe fail.

Fixes: 67c2315d ("crypto: caam - add Queue Interface (QI) backend support")
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Cc: "Horia Geantă" <horia.geanta@nxp.com>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Cc: <stable@vger.kernel.org> # 4.12+
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 900a081f upstream.

When we have an unaligned SG list entry where there is no leftover
aligned data, the hash walk code will incorrectly return zero as if
the entire SG list has been processed.

This patch fixes it by moving onto the next page instead.
Reported-by: Eli Cooper <elicooper@gmx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 333e18c5 upstream.

The RSA private key for the first form should have
version, prime1, prime2, exponent1, exponent2, coefficient
values 0.
With non-zero values for prime1,2, exponent 1,2 and coefficient
the Intel QAT driver will assume that values are provided for the
private key second form. This will result in signature verification
failures for modules where QAT device is present and the modules
are signed with rsa,sha256.

Cc: <stable@vger.kernel.org>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Conor McLoughlin <conor.mcloughlin@intel.com>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f962eb46 upstream.

In this driver the clock is got but never put when the driver is removed
or if there is an error in the probe.

Using the managed version of clk_get() allows to let the kernel take care
of it.

Fixes: 1b44c5a6 ("crypto: inside-secure - add SafeXcel EIP197 crypto
engine driver")
cc: stable@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8c9bdab2 upstream.

The buffer rctx->ext contains potentially sensitive data and should
be freed with kzfree.

Cc: <stable@vger.kernel.org>
Fixes: 700cb3f5 ("crypto: lrw - Convert to skcipher")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 823f7923 upstream.

WCH CH382L is a PCI-E adapter with 1 parallel port. It is similair to CH382
but serial ports are not soldered on board. Detected as
Serial controller: Device 1c00:3050 (rev 10) (prog-if 05 [16850])
Signed-off-by: Alexander Gerasiov <gq@redlab-i.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 50e70445 upstream.

Quoting the original report:

It looks like there is a double-free vulnerability in Linux usbtv driver
on an error path of usbtv_probe function. When audio registration fails,
usbtv_video_free function ends up freeing usbtv data structure, which
gets freed the second time under usbtv_video_fail label.

usbtv_audio_fail:

        usbtv_video_free(usbtv); =>

           v4l2_device_put(&usbtv->v4l2_dev);

              => v4l2_device_put

                  => kref_put

                      => v4l2_device_release

  => usbtv_release (CALLBACK)

                             => kfree(usbtv) (1st time)

usbtv_video_fail:

        usb_set_intfdata(intf, NULL);

        usb_put_dev(usbtv->udev);

        kfree(usbtv); (2nd time)

So, as we have refcounting, use it
Reported-by: Yavuz, Tuba <tuba@ece.ufl.edu>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b5b38200 upstream.

Successes in probe_kernel_read() would mask failures in copy_to_user()
during read_mem().
Reported-by: Brad Spengler <spender@grsecurity.net>
Fixes: 22ec1a2a ("/dev/mem: Add bounce buffer for copy-out")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bb0829a7 upstream.

Currently the driver spams the kernel log on unsupported ioctls which is
unnecessary as the ioctl returns -ENOIOCTLCMD to indicate this anyway.
I suspect this was originally for debugging purposes but it really is not
required so remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f597fbce upstream.

The Nuvoton UART is almost compatible with the 8250 driver when probed
via the 8250_of driver, however it requires some extra configuration
at startup.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1f1e82f7 upstream.

Add device id for ELDAT Easywave RX09 tranceiver.
Reported-by: Jan Jansen <nattelip@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6555ad13 upstream.

Add device id for Harman FirmwareHubEmulator to make the device
auto-detectable by the driver.
Signed-off-by: Clemens Werther <clemens.werther@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9608e5c0 upstream.

This patch adds a device ID for the RT Systems cable used to
program Yaesu VX-8R/VX-8DR handheld radios. It uses the main
FTDI VID instead of the common RT Systems VID.
Signed-off-by: Major Hayden <major@mhtx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 21035965 upstream.

Commit 2a98dc02 ("include/linux/bitmap.h: turn bitmap_set and
bitmap_clear into memset when possible") introduced an optimization to
bitmap_{set,clear}() which uses memset() when the start and length are
constants aligned to a byte.

This is wrong on big-endian systems; our bitmaps are arrays of unsigned
long, so bit n is not at byte n / 8 in memory.  This was caught by the
Btrfs selftests, but the bitmap selftests also fail when run on a
big-endian machine.

We can still use memset if the start and length are aligned to an
unsigned long, so do that on big-endian.  The same problem applies to
the memcmp in bitmap_equal(), so fix it there, too.

Fixes: 2a98dc02 ("include/linux/bitmap.h: turn bitmap_set and bitmap_clear into memset when possible")
Fixes: 2c6deb01 ("bitmap: use memcmp optimisation in more situations")
Cc: stable@kernel.org
Reported-by: "Erhard F." <erhard_f@mailbox.org>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d2471d4a upstream.

In the earlier commit dad3f793 ("usb: dwc2: Make sure we
disconnect the gadget state"), I was trying to fix up the
fact that we somehow weren't disconnecting the gadget state,
so that when the OTG port was plugged in the second time we
would get warnings about the state tracking being wrong.

(This seems to be due to a quirk of the HiKey board where
we do not ever get any otg interrupts, particularly the session
end detected signal. Instead we only see status change
interrupt.)

The fix there was somewhat simple, as it just made sure to
call dwc2_hsotg_disconnect() before we connected things up
in OTG mode, ensuring the state handling didn't throw errors.

But in looking at a different issue I was seeing with UDC
state handling, I realized that it would be much better
to call dwc2_hsotg_disconnect when we get the state change
signal moving to host mode.

Thus, this patch removes the earlier disconnect call I added
and moves it (and the needed locking) to the host mode
transition.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 64e759f5 upstream.

If Security Request is received on connection that is already encrypted
with sufficient security master should perform encryption key refresh
procedure instead of just ignoring Slave Security Request
(Core Spec 5.0 Vol 3 Part H 2.4.6).

> ACL Data RX: Handle 3585 flags 0x02 dlen 6
      SMP: Security Request (0x0b) len 1
        Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
        Handle: 3585
        Random number: 0x0000000000000000
        Encrypted diversifier: 0x0000
        Long term key: 44264272a5c426a9e868f034cf0e69f3
> HCI Event: Command Status (0x0f) plen 4
      LE Start Encryption (0x08|0x0019) ncmd 1
        Status: Success (0x00)
> HCI Event: Encryption Key Refresh Complete (0x30) plen 3
        Status: Success (0x00)
        Handle: 3585
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 59fba086 upstream.

While the specific UFS PHY drivers (14nm and 20nm) have a module
license, the common base module does not, leading to a Kbuild
failure:

WARNING: modpost: missing MODULE_LICENSE() in drivers/phy/qualcomm/phy-qcom-ufs.o
FATAL: modpost: GPL-incompatible module phy-qcom-ufs.ko uses GPL-only symbol 'clk_enable'

This adds a module description and license tag to fix the build.
I added both Yaniv and Vivek as authors here, as Yaniv sent the initial
submission, while Vivek did most of the work since.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>