When the controller is being reset or power cycled, then the flag
HCI_LL_RPA_RESOLUTION which indicates if controller based address
resolution is active needs to be also reset.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When starting active scanning for discovery the whitelist is not needed
to be used. So the filter_policy is 0x00. To make the core more readable
use a variable name instead of just setting 0 as paramter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The list of LE features constants has gotten a bit confused. It lost the
order and gained duplicated. Clean this up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Add new compatible device RTL8761B. RTL8761B is a USB Bluetooth device,
with support of BLE and BR/EDR. The USB info is

T:  Bus=03 Lev=04 Prnt=04 Port=00 Cnt=01 Dev#= 29 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=8771 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=XXXXXXXXXXXX
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Ziqian SUN (Zamir) <sztsian@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The error could indicate a problem with the Bluetooth device. It
is easier to investigate if the packet's actual length gets logged,
not just the fact that a discrepancy occurred.
Signed-off-by: Daniels Umanovskis <du@axentia.se>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

To improve security, always give the user-space daemon a chance to
accept or reject a Just Works pairing (LE). The daemon may decide to
auto-accept based on the user's intent.

This patch is similar to the previous patch but applies for LE Secure
Connections (SC).
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The new btusb_find_altsetting() dereferences it without checking
the check is added in this patch
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some static checker run by 0day reports a variableScope warning.

net/bluetooth/smp.c:870:6: warning:
	The scope of the variable 'err' can be reduced. [variableScope]

There is no need for two separate variables holding return values.
Stick with the existing variable. While at it, don't pre-initialize
'ret' because it is set in each code path.

tk_request() is supposed to return a negative error code on errors,
not a bluetooth return code. The calling code converts the return
value to SMP_UNSPECIFIED if needed.

Fixes: 92516cd9 ("Bluetooth: Always request for user confirmation for Just Works")
Cc: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The BT qualification test SM/MAS/PKE/BV-01-C needs us to turn off
the MITM flag when pairing, and at the same time also set the io
capability to something other than no input no output.

Currently the MITM flag is only unset when the io capability is set
to no input no output, therefore the test cannot be executed.

This patch introduces a debugfs option to force MITM flag to be
turned off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch assigns the next free HCI device identifier to Bluetooth
devices based on VIRTIO devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Increment the mgmt revision due to the recently added new commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

To allow userspace to make correcty security policy decision, the kernel
needs to export a few details of the supported security features and
encryption key size information. This command exports this information
and also allows future extensions if needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

With the Read Local Simple Pairing Options command it is possible to
retrieve the support for max encryption key size supported by the
controller and also if the controller correctly verifies the ECDH public
key during pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The Intel ThundePeak BT controllers support the Microsoft vendor
extension and they are using 0xFC1E for VsMsftOpCode.

< HCI Command: Vendor (0x3f|0x001e) plen 1
        00
> HCI Event: Command Complete (0x0e) plen 15
      Vendor (0x3f|0x001e) ncmd 1
        Status: Success (0x00)
        00 3f 00 00 00 00 00 00 00 01 50
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

In case the controller is already in operation mode, the Intel specific
events will not be enabled. Fix this by jumping to a common finish
section that will allow setting final details for the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Micrsoft defined a set for HCI vendor extensions. Check the following
link for details:

https://docs.microsoft.com/en-us/windows-hardware/drivers/bluetooth/microsoft-defined-bluetooth-hci-commands-and-events

This provides the basic framework to enable the extension and read its
supported features. Drivers still have to declare support for this
extension before it can be utilized by the host stack.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

This is just a cosmetic clean to move the selftests configuration option
to the bottom of the list of options.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

For mSBC encoded audio stream over usb transport, btusb driver
to be set to alternate settings 6 as per BT core spec 5.0. The
type of air mode is used to differenting which alt setting to be
used.

The changes are made considering some discussion over the similar
patch submitted earlier from Kuba Pawlak (link below)
https://www.spinics.net/lists/linux-bluetooth/msg64577.htmlReported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

This changes a simple typo in hci_event.c
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When scheduling TX packets, send all SCO/eSCO packets first, check for
pending SCO/eSCO packets after every ACL/LE packet and send them if any
are pending.  This is done to make sure that we can meet SCO deadlines
on slow interfaces like UART.

If we were to queue up multiple ACL packets without checking for a SCO
packet, we might miss the SCO timing. For example:

The time it takes to send a maximum size ACL packet (1024 bytes):
t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
        where 10/8 is uart overhead due to start/stop bits per byte

Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666.

At a baudrate of 3000000, if we didn't check for SCO packets within 1024
bytes, we would miss the 3.75ms timing window.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When BT module can't be initialized, but it has an IRQ, unloading
the driver WARNs when trying to free not-yet-requested IRQ. Fix it by
noting whether the IRQ was requested.

WARNING: CPU: 2 PID: 214 at kernel/irq/devres.c:144 devm_free_irq+0x49/0x4ca
[...]
WARNING: CPU: 2 PID: 214 at kernel/irq/manage.c:1746 __free_irq+0x8b/0x27c
Trying to free already-free IRQ 264
Modules linked in: hci_uart(-) btbcm bluetooth ecdh_generic ecc libaes
CPU: 2 PID: 214 Comm: rmmod Tainted: G        W         5.6.1mq-00044-ga5f9ea098318-dirty #928
[...]
[<b016aefb>] (devm_free_irq) from [<af8ba1ff>] (bcm_close+0x97/0x118 [hci_uart])
[<af8ba1ff>] (bcm_close [hci_uart]) from [<af8b736f>] (hci_uart_unregister_device+0x33/0x3c [hci_uart])
[<af8b736f>] (hci_uart_unregister_device [hci_uart]) from [<b035930b>] (serdev_drv_remove+0x13/0x20)
[<b035930b>] (serdev_drv_remove) from [<b037093b>] (device_release_driver_internal+0x97/0x118)
[<b037093b>] (device_release_driver_internal) from [<b0370a0b>] (driver_detach+0x2f/0x58)
[<b0370a0b>] (driver_detach) from [<b036f855>] (bus_remove_driver+0x41/0x94)
[<b036f855>] (bus_remove_driver) from [<af8ba8db>] (bcm_deinit+0x1b/0x740 [hci_uart])
[<af8ba8db>] (bcm_deinit [hci_uart]) from [<af8ba86f>] (hci_uart_exit+0x13/0x30 [hci_uart])
[<af8ba86f>] (hci_uart_exit [hci_uart]) from [<b01900bd>] (sys_delete_module+0x109/0x1d0)
[<b01900bd>] (sys_delete_module) from [<b0101001>] (ret_fast_syscall+0x1/0x5a)
[...]

Cc: stable@vger.kernel.org
Fixes: 6cc4396c ("Bluetooth: hci_bcm: Add wake-up capability")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The IRQ polarity is be configured in bcm_setup_sleep(). Make the
configured value match what is in the DeviceTree.

Cc: stable@vger.kernel.org
Fixes: f25a96c8 ("Bluetooth: hci_bcm: enable IRQ capability from devicetree")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

To improve security, always give the user-space daemon a chance to
accept or reject a Just Works pairing (LE). The daemon may decide to
auto-accept based on the user's intent.
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This adds BT_MODE socket option which can be used to set L2CAP modes,
including modes only supported over LE which were not supported using
the L2CAP_OPTIONS.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

L2CAP_OPTIONS shall only be used with BR/EDR modes.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds compatible string for the QCA chip QCA6390.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for QCA6390, including the devicetree and acpi
compatible hwid matching, and patch/nvm downloading.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Every remaining user just has the error case returning -EFAULT.

In fact, the exception was __get_user_asm_nozero(), which was removed in
commit 4b842e4e ("x86: get rid of small constant size cases in
raw_copy_{to,from}_user()"), and the other __get_user_xyz() macros just
followed suit for consistency.

Fix up some macro whitespace while at it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The last user was removed by commit 4b842e4e ("x86: get rid of small
constant size cases in raw_copy_{to,from}_user()").  Get rid of the
left-overs before somebody tries to use it again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking updates from David Miller:
 "Highlights:

   1) Fix the iwlwifi regression, from Johannes Berg.

   2) Support BSS coloring and 802.11 encapsulation offloading in
      hardware, from John Crispin.

   3) Fix some potential Spectre issues in qtnfmac, from Sergey
      Matyukevich.

   4) Add TTL decrement action to openvswitch, from Matteo Croce.

   5) Allow paralleization through flow_action setup by not taking the
      RTNL mutex, from Vlad Buslov.

   6) A lot of zero-length array to flexible-array conversions, from
      Gustavo A. R. Silva.

   7) Align XDP statistics names across several drivers for consistency,
      from Lorenzo Bianconi.

   8) Add various pieces of infrastructure for offloading conntrack, and
      make use of it in mlx5 driver, from Paul Blakey.

   9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.

  10) Lots of parallelization improvements during configuration changes
      in mlxsw driver, from Ido Schimmel.

  11) Add support to devlink for generic packet traps, which report
      packets dropped during ACL processing. And use them in mlxsw
      driver. From Jiri Pirko.

  12) Support bcmgenet on ACPI, from Jeremy Linton.

  13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
      Starovoitov, and your's truly.

  14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.

  15) Fix sysfs permissions when network devices change namespaces, from
      Christian Brauner.

  16) Add a flags element to ethtool_ops so that drivers can more simply
      indicate which coalescing parameters they actually support, and
      therefore the generic layer can validate the user's ethtool
      request. Use this in all drivers, from Jakub Kicinski.

  17) Offload FIFO qdisc in mlxsw, from Petr Machata.

  18) Support UDP sockets in sockmap, from Lorenz Bauer.

  19) Fix stretch ACK bugs in several TCP congestion control modules,
      from Pengcheng Yang.

  20) Support virtual functiosn in octeontx2 driver, from Tomasz
      Duszynski.

  21) Add region operations for devlink and use it in ice driver to dump
      NVM contents, from Jacob Keller.

  22) Add support for hw offload of MACSEC, from Antoine Tenart.

  23) Add support for BPF programs that can be attached to LSM hooks,
      from KP Singh.

  24) Support for multiple paths, path managers, and counters in MPTCP.
      From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
      and others.

  25) More progress on adding the netlink interface to ethtool, from
      Michal Kubecek"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
  net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
  cxgb4/chcr: nic-tls stats in ethtool
  net: dsa: fix oops while probing Marvell DSA switches
  net/bpfilter: remove superfluous testing message
  net: macb: Fix handling of fixed-link node
  net: dsa: ksz: Select KSZ protocol tag
  netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
  net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
  net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
  net: stmmac: create dwmac-intel.c to contain all Intel platform
  net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
  net: dsa: bcm_sf2: Add support for matching VLAN TCI
  net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
  net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
  net: dsa: bcm_sf2: Disable learning for ASP port
  net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
  net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
  net: dsa: b53: Restore VLAN entries upon (re)configuration
  net: dsa: bcm_sf2: Fix overflow checks
  hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
  ...

Pull NTB updates from Jon Mason:
 "Bug fixes for a few printing issues, link status detection bug on AMD
  hardware, and a DMA address issue with ntb_perf.

  Also, large series of AMD NTB patches"

* tag 'ntb-5.7' of git://github.com/jonmason/ntb: (21 commits)
  NTB: add pci shutdown handler for AMD NTB
  NTB: send DB event when driver is loaded or un-loaded
  NTB: remove redundant setting of DB valid mask
  NTB: return link up status correctly for PRI and SEC
  NTB: add helper functions to set and clear sideinfo
  NTB: move ntb_ctrl handling to init and deinit
  NTB: handle link up, D0 and D3 events correctly
  NTB: handle link down event correctly
  NTB: remove handling of peer_sta from amd_link_is_up
  NTB: set peer_sta within event handler itself
  NTB: return the side info status from amd_poll_link
  NTB: define a new function to get link status
  NTB: Enable link up and down event notification
  NTB: clear interrupt status register
  NTB: Fix access to link status and control register
  MAINTAINERS: update maintainer list for AMD NTB driver
  NTB: ntb_transport: Use scnprintf() for avoiding potential buffer overflow
  ntb_hw_switchtec: Fix ntb_mw_clear_trans error if size == 0
  ntb_tool: Fix printk format
  NTB: ntb_perf: Fix address err in perf_copy_chunk
  ...

Pull x86 platform driver updates from Andy Shevchenko:

 - Fix for improper handling of fan_boost_mode in sysfs for ASUS
   laptops.

 - On newer ASUS laptops the 1st battery is named differently, here is a
   fix.

 - Fix Lex 2I385SW to allow both network cards to be used.

 - The power integrated circuit driver for Surface 3 has been added.

 - Refactor and clean up of Intel PMC driver and enable it on Intel
   Jasper Lake.

 - Clean up of Dell RBU driver.

 - Big update for Intel Speed Select technology support tool and driver.

* tag 'platform-drivers-x86-v5.7-1' of git://git.infradead.org/linux-platform-drivers-x86: (75 commits)
  platform/x86: surface3_power: Fix always true condition in mshw0011_space_handler()
  platform/x86: surface3_power: Fix Kconfig section ordering
  platform/x86: surface3_power: Add missed headers
  platform/x86: surface3_power: Reformat GUID assignment
  platform/x86: surface3_power: Drop useless macro ACPI_PTR()
  platform/x86: surface3_power: Prefix POLL_INTERVAL with SURFACE_3
  platform/x86: surface3_power: Simplify mshw0011_adp_psr() to one liner
  platform/x86: surface3_power: Use dev_err() instead of pr_err()
  platform/x86: surface3_power: Drop unused structure definition
  platform/x86: surface3_power: MSHW0011 rev-eng implementation
  platform/x86: intel_pmc_core: Make pmc_core_substate_res_show() generic
  platform/x86: intel_pmc_core: Make pmc_core_lpm_display() generic for platforms that support sub-states
  tools/power/x86/intel-speed-select: Fix a typo in error message
  tools/power/x86/intel-speed-select: Update version
  tools/power/x86/intel-speed-select: Avoid duplicate Package strings for json
  tools/power/x86/intel-speed-select: Add display for enabled cpus count
  tools/power/x86/intel-speed-select: Print friendly warning for bad command line
  tools/power/x86/intel-speed-select: Fix avx options for turbo-freq feature
  tools/power/x86/intel-speed-select: Improve CLX commands
  tools/power/x86/intel-speed-select: Show error for invalid CPUs in the options
  ...

Pull tty/serial updates from Greg KH:
 "Here is the big set of TTY / Serial patches for 5.7-rc1

  Lots of console fixups and reworking in here, serial core tweaks
  (doesn't that ever get old, why are we still creating new serial
  devices?), serial driver updates, line-protocol driver updates, and
  some vt cleanups and fixes included in here as well.

  All have been in linux-next with no reported issues"

* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
  serial: 8250: Optimize irq enable after console write
  serial: 8250: Fix rs485 delay after console write
  vt: vt_ioctl: fix use-after-free in vt_in_use()
  vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
  tty: serial: make SERIAL_SPRD depend on COMMON_CLK
  tty: serial: fsl_lpuart: fix return value checking
  tty: serial: fsl_lpuart: move dma_request_chan()
  ARM: dts: tango4: Make /serial compatible with ns16550a
  ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
  ARM: dts: mmp*: Fix serial port names
  ARM: dts: mmp2-brownstone: Don't redeclare phandle references
  ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
  ARM: dts: pxa*: Fix serial port names
  ARM: dts: pxa*: Don't redeclare phandle references
  serial: omap: drop unused dt-bindings header
  serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
  serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
  serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
  serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
  serial: 8250: 8250_omap: Account for data in flight during DMA teardown
  ...

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Add support for host software queue for (e)MMC/SD
   - Throttle polling rate for CMD6
   - Update CMD13 busy condition check for CMD6 commands
   - Improve busy detect polling for erase/trim/discard/HPI
   - Fixup support for HW busy detection for HPI commands
   - Re-work and improve support for eMMC sanitize commands

  MMC host:
   - mmci:
       * Add support for sdmmc variant revision 2.0
   - mmci_sdmmc:
       * Improve support for busyend detection
       * Fixup support for signal voltage switch
       * Add support for tuning with delay block
   - mtk-sd:
       * Fix another SDIO irq issue
   - sdhci:
       * Disable native card detect when GPIO based type exist
   - sdhci:
       * Add option to defer request completion
   - sdhci_am654:
       * Add support to set a tap value per speed mode
   - sdhci-esdhc-imx:
       * Add support for i.MX8MM based variant
       * Fixup support for standard tuning on i.MX8 usdhc
       * Optimize for strobe/clock dll settings
       * Fixup support for system and runtime suspend/resume
   - sdhci-iproc:
       * Update regulator/bus-voltage management for bcm2711
   - sdhci-msm:
       * Prevent clock gating with PWRSAVE_DLL on broken variants
       * Fix management of CQE during SDHCI reset
   - sdhci-of-arasan:
       * Add support for auto tuning on ZynqMP based platforms
   - sdhci-omap:
       * Add support for system suspend/resume
   - sdhci-sprd:
       * Add support for HW busy detection
       * Enable support host software queue
   - sdhci-tegra:
       * Add support for HW busy detection
   - tmio/renesas_sdhi:
       * Enforce retune after runtime suspend
   - renesas_sdhi:
       * Use manual tap correction for HS400 on some variants
       * Add support for manual correction of tap values for tunings"

* tag 'mmc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
  mmc: cavium-octeon: remove nonsense variable coercion
  mmc: mediatek: fix SDIO irq issue
  mmc: mmci_sdmmc: Fix clear busyd0end irq flag
  dt-bindings: mmc: Fix node name in an example
  mmc: core: Re-work the code for eMMC sanitize
  mmc: sdhci: use FIELD_GET for preset value bit masks
  mmc: sdhci-of-at91: Display clock changes for debug purpose only
  mmc: sdhci: iproc: Add custom set_power() callback for bcm2711
  mmc: sdhci: am654: Use sdhci_set_power_and_voltage()
  mmc: sdhci: at91: Use sdhci_set_power_and_voltage()
  mmc: sdhci: milbeaut: Use sdhci_set_power_and_voltage()
  mmc: sdhci: arasan: Use sdhci_set_power_and_voltage()
  mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()
  mmc: vub300: Use scnprintf() for avoiding potential buffer overflow
  dt-bindings: mmc: synopsys-dw-mshc: fix clock-freq-min-max in example
  sdhci: tegra: Enable MMC_CAP_WAIT_WHILE_BUSY host capability
  sdhci: tegra: Implement Tegra specific set_timeout callback
  mmc: sdhci-omap: Add Support for Suspend/Resume
  mmc: renesas_sdhi: simplify execute_tuning
  mmc: renesas_sdhi: Use BITS_PER_LONG helper
  ...

Pull Kbuild updates from Masahiro Yamada:
 "Build system:

   - add CONFIG_UNUSED_KSYMS_WHITELIST, which will be useful to define a
     fixed set of export symbols for Generic Kernel Image (GKI)

   - allow to run 'make dt_binding_check' without .config

   - use full schema for checking DT examples in *.yaml files

   - make modpost fail for missing MODULE_IMPORT_NS(), which makes more
     sense because we know the produced modules are never loadable

   - Remove unused 'AS' variable

  Kconfig:

   - sanitize DEFCONFIG_LIST, and remove ARCH_DEFCONFIG from Kconfig
     files

   - relax the 'imply' behavior so that symbols implied by 'y' can
     become 'm'

   - make 'imply' obey 'depends on' in order to make 'imply' really weak

  Misc:

   - add documentation on building the kernel with Clang/LLVM

   - revive __HAVE_ARCH_STRLEN for 32bit sparc to use optimized strlen()

   - fix warning from deb-pkg builds when CONFIG_DEBUG_INFO=n

   - various script and Makefile cleanups"

* tag 'kbuild-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
  Makefile: Update kselftest help information
  kbuild: deb-pkg: fix warning when CONFIG_DEBUG_INFO is unset
  kbuild: add outputmakefile to no-dot-config-targets
  kbuild: remove AS variable
  net: wan: wanxl: refactor the firmware rebuild rule
  net: wan: wanxl: use $(M68KCC) instead of $(M68KAS) for rebuilding firmware
  net: wan: wanxl: use allow to pass CROSS_COMPILE_M68k for rebuilding firmware
  kbuild: add comment about grouped target
  kbuild: add -Wall to KBUILD_HOSTCXXFLAGS
  kconfig: remove unused variable in qconf.cc
  sparc: revive __HAVE_ARCH_STRLEN for 32bit sparc
  kbuild: refactor Makefile.dtbinst more
  kbuild: compute the dtbs_install destination more simply
  Makefile: disallow data races on gcc-10 as well
  kconfig: make 'imply' obey the direct dependency
  kconfig: allow symbols implied by y to become m
  net: drop_monitor: use IS_REACHABLE() to guard net_dm_hw_report()
  modpost: return error if module is missing ns imports and MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS=n
  modpost: rework and consolidate logging interface
  kbuild: allow to run dt_binding_check without kernel configuration
  ...

Merge branch 'next-general' of git://git.kernel.org:/pub/scm/linux/kernel/git/jmorris/linux-security

Pull security subsystem updates from James Morris:
 "Two minor updates for the core security subsystem:

   - kernel-doc warning fixes from Randy Dunlap

   - header cleanup from YueHaibing"

* 'next-general' of git://git.kernel.org:/pub/scm/linux/kernel/git/jmorris/linux-security:
  security: remove duplicated include from security.h
  security: <linux/lsm_hooks.h>: fix all kernel-doc warnings

Pull SELinux updates from Paul Moore:
 "We've got twenty SELinux patches for the v5.7 merge window, the
  highlights are below:

   - Deprecate setting /sys/fs/selinux/checkreqprot to 1.

     This flag was originally created to deal with legacy userspace and
     the READ_IMPLIES_EXEC personality flag. We changed the default from
     1 to 0 back in Linux v4.4 and now we are taking the next step of
     deprecating it, at some point in the future we will take the final
     step of rejecting 1.

   - Allow kernfs symlinks to inherit the SELinux label of the parent
     directory. In order to preserve backwards compatibility this is
     protected by the genfs_seclabel_symlinks SELinux policy capability.

   - Optimize how we store filename transitions in the kernel, resulting
     in some significant improvements to policy load times.

   - Do a better job calculating our internal hash table sizes which
     resulted in additional policy load improvements and likely general
     SELinux performance improvements as well.

   - Remove the unused initial SIDs (labels) and improve how we handle
     initial SIDs.

   - Enable per-file labeling for the bpf filesystem.

   - Ensure that we properly label NFS v4.2 filesystems to avoid a
     temporary unlabeled condition.

   - Add some missing XFS quota command types to the SELinux quota
     access controls.

   - Fix a problem where we were not updating the seq_file position
     index correctly in selinuxfs.

   - We consolidate some duplicated code into helper functions.

   - A number of list to array conversions.

   - Update Stephen Smalley's email address in MAINTAINERS"

* tag 'selinux-pr-20200330' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: clean up indentation issue with assignment statement
  NFS: Ensure security label is set for root inode
  MAINTAINERS: Update my email address
  selinux: avtab_init() and cond_policydb_init() return void
  selinux: clean up error path in policydb_init()
  selinux: remove unused initial SIDs and improve handling
  selinux: reduce the use of hard-coded hash sizes
  selinux: Add xfs quota command types
  selinux: optimize storage of filename transitions
  selinux: factor out loop body from filename_trans_read()
  security: selinux: allow per-file labeling for bpffs
  selinux: generalize evaluate_cond_node()
  selinux: convert cond_expr to array
  selinux: convert cond_av_list to array
  selinux: convert cond_list to array
  selinux: sel_avc_get_stat_idx should increase position index
  selinux: allow kernfs symlinks to inherit parent directory context
  selinux: simplify evaluate_cond_node()
  Documentation,selinux: deprecate setting checkreqprot to 1
  selinux: move status variables out of selinux_ss

Pull audit updates from Paul Moore:
 "We've got two audit patches for the v5.7 merge window with a stellar
  14 lines changed between the two patches. The patch descriptions are
  far more lengthy than the patches themselves, which is a very good
  thing for patches this size IMHO. The patches pass our test suites and
  a quick summary is below:

   - Stop logging inode information when updating an audit file watch.

     Since we are not changing the inode, or the fact that we are
     watching the associated file, the inode information is just noise
     that we can do without.

   - Fix a problem where mandatory audit records were missing their
     accompanying audit records (e.g. SYSCALL records were missing).

     The missing records often meant that we didn't have the necessary
     context to understand what was going on when the event occurred"

* tag 'audit-pr-20200330' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
  audit: trigger accompanying records when no rules present
  audit: CONFIG_CHANGE don't log internal bookkeeping as an event